Renesas User System Interface Board HS1664ECH61H manuale d’uso

H8SX/1663 Group E600 0H FP-144L User System Interface Boa rd HS1664ECH61H User’s Manual Renesas M icrocomput er Developm ent Envi ronment System H8SX Family / H8SX/ 1600 Ser ies HS1664EC H61HE REJ10J1395-0100 Revision Date: Jun. 28, 2006 Rev.1.00[...]

[...]

1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp[...]

[...]

I IMPORTANT INFORMATION READ FIRST • READ this user's ma nual bef ore using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to u se the user s ystem in terface board until y ou fully understa nd its mechanism. User Syst em Interf ace Board : Throughout this docume nt, t he term &qu[...]

II LIMITED WA RRANTY Renesas warrants its user syst em interfa ce boards to be manufactu red in accordance with published specifications and fr ee from defects in material and/or workmanship. Renesas will repair or replace any user system interfac e boards determined to be defective in mate rial and/or workmanship. Us er system interface bo ards ar[...]

III State Law : Some states do not allo w the exclusion or limitation of implied warranties o r liability for incidental or c onsequential damages, s o the above limit ation or exclus ion may not apply to you. This warrant y gives you s pecific l egal rights, and you may have other rights whi ch may va ry from state to state. The Warrant y is Void [...]

IV SAFETY PAGE READ FIRST • READ this user's ma nual bef ore using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to use the user s ystem in terface boa rd until you fully understand its mechanism. DEFINITION OF SI GNAL WORDS This is the safety ale rt symb ol. It is used to alert [...]

V W ARNING Observe the pr ecautions listed b elow. Failure t o do so will result in a FIRE H AZARD and will damage the us er system and the emul ator product or will r esult in PERSONAL INJURY. The USER PROGRA M will be LOST. 1. Do not repair or remodel the emul ator product by yourself for elect ric shock pre vention and quality assurance. 2. Alwa[...]

i Preface The HS1664ECH61H is a us er system interface board that connects a user s ystem for the H8SX/1663, H8S X/1664 FP-144L package to t he H8SX/1650 E6000H emulat or (HS1650EPH60H). Emul ation of the H8S X/1663 group is only pos sible w hen this user s ystem interface board is connected to the HS1650EPH60H.[...]

ii Contents Section 1 Configuration ..................................................................................... 1 Section 2 Connection Procedures ...................................................................... 3 2.1 Connecting the User System Interf ace B oard to the User System .................................... 3 2.1.1 Installi[...]

1 Section 1 Configuration Figure 1 and table 1 show the conf iguration and component s of the user syst em interface board for the FP-144L package. Pleas e make sure you ha ve all of these component s after you have unpacked the box. Evaluation chip board Spacer User system interface board User system IC socket Screws (M2 × 10 mm) (for fastening t[...]

2 CAUTION Use an NQPACK 144SD socket (manufact ured by Tokyo Eletech Corporati on) as the FP-144L- packaged IC socket on the user syst em. Table 1 HS1664ECH61H Com ponents No. Component Quantity Remarks 1 User system interface board 1 2 IC socket 1 For the FP-144L package (to be mounted on the user system) 3 Socket cover 1 For installing an FP-144L[...]

3 Section 2 Connection Procedures 2.1 Connecting the User Sy stem Interface Board to the User System W ARNING Always switch OFF the user syst em and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed. Before connecting t he two, make sure that pin 1 on both sides are correct ly aligned. Failure to do so will result [...]

4 To connect th e board to th e user system, follo w the instructions b elow. 2.1.1 Installing the IC So cket After checking the locat ion of pin 1 on the IC s ocket fasten it to the user s ystem before soldering. CAUTION After confirming the locat ion of pin 1 on the IC socket, apply epoxy resin adhesive to the end of t he four projections at the [...]

5 2.1.2 Soldering the IC Socket After fastening, s older the IC socket for an F P-144L package to the user sys tem. CAUTION Be sure to completely solder the leads so th at the solder gently covers the leads and forms solder fillets. (Use slightly more solder than with the MCU.) 2.1.3 Inserting the IC Socket Connector CAUTION Check the location of p[...]

6 2.1.4 Fastening th e IC Socket Connector CAUTION 1. Use the screwdriver provided for t ightening screws. 2. The tightening torque must be 0.054 N•m or less. If the applied torque ca nnot be accurately measured, stop tightening when the f orce required to turn th e screw becomes significantly greater t h an that needed when f irst tightening. If[...]

7 User system interface board User system Pin 1 Screws (M2 × 10 mm) (for fastenin g the board) IC socket (NQPACK144SD manufactured by Tokyo Eletech Corporation) Figure 3 Connecting the User System In terface B oard to the User System[...]

8 2.2 Exchanging the S pacers of the Evaluation Ch ip Board After connecting the user system in terface board to the us er system, be careful not to apply load to the user system. Exchange the spacers (2.6MP × 10 mm) of the evaluation chip board with the spacers (2.6MP × 25 mm) provided with the user system interface board and adjust the height. [...]

9 2.3 Connecting the User Syst em Interface Board to the Evaluation Chip Board W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user syst em and the emulator [...]

10 Connector No. UCN1 UCN1 UCN2 UCN2 User system interface board Evaluation Chip Board Connector No. Board Connector No. Evaluation chip board Figure 5 Connecting the User System Interface Board to the Evaluation Chip B oard[...]

11 2.4 Recommended Dimensions for the User System Mounting Pad (Footprint) Figure 6 shows the recommended dimensions for the mounting pad (footpri nt) for the user sys tem with the IC s ocket for an FP-144L package (NQP ACK144SD: manufact ured by Tokyo Eletech Corporation). Note t hat the dimensions in figure 6 are somewhat different from those of [...]

12 2.5 Dimensions of the Evaluation Chip Board and the User System Interface Board The dimensions of the evaluati on chip board and the user s ystem interface board are shown in figure 7. Unit: mm Tolerance: ± 0.5 mm 140.0 Evaluation chip board User system interface board 102.5 16.0 118.5 100.0 84.5 69.0 78.5 34.5 Figure 7 Dimen sions of th e Eval[...]

13 2.6 Resulting Dimensions after Conn ecting the User Sy stem Interface Board The dimensions of the ass embly after the user system interface board has been connected to the user syst em are shown in figure 8. Unit: mm Tolerance: ±1.0 mm 32.9 13.3 54.9 User system Evaluation chip board IC socket (NQPACK144SD manufactured by Tokyo Eletech Corporat[...]

14 2.7 Using the Emulator with out Connecting User System W ARNING Always switch OFF the user syst em and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed. Before connecting t he two, make sure that pin 1 on both sides are correct ly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user s[...]

15 P1 SW1 USER ON USER OFF Figure 9 SW1 Jumper Socket Spacer (2.6MQ x 13 mm) Figure 10 Attaching Spacers[...]

16 Section 3 User System Interface Circuits The following user interface circuits are required fo r the emulator when th e user system interface board is in use. Sub-MCU MD control circuit Monitorin g circuit LPT16244 MD_CLK Vcc 47 k Ω PM0-PM4 User system VBUS MD_CLK DrVss DrVss PM0-PM4 VBUS DrVcc DrVcc USD- USD- USD+ USD+ Power-supply circuit EPM[...]

17 P23 P27 P23 P27 SN74CB3Q3306A SN74CB3Q3306A MCU User system Figure 12 User System Interface Circuit (2) MCU User system Sub-MCU P14 P14 SN74CB3Q3306A TXD SN74CB3Q3306A Figure 13 User System Interface Circuit (3)[...]

18 MCU VHC244 UHC14 _RES Vcc User system EPM7128 EPM7128 _RES 47 k Ω Figure 14 User System Interface Circuit (4)[...]

19 Section 4 Verifying Operation 1. Turn on the emulator according to the pr ocedures described in the H8SX/1650 E6000H Emulator User' s Manual (HS1650EPH 60HE). 2. Verify the user system interface cable c onnections by checking the pin s tates with the EXMONITOR_DISPLAY command (emulator command ) and checking the bus states with the MEMORY_F[...]

20 ⎯ To use the crystal oscillator mount ed on the evaluation chip board Install the cry stal oscillator into the cr ystal oscillator termin als on the evalua tion chip board. Evaluation chip board Crystal oscillator terminals Crystal oscillator Enlar g ed view X1 X2 Figure 16 Insta lling the Clock Oscillato r[...]

21 Section 5 Points for Caution 1. Before connecting any parts or cables, make sure that the pins at the pin 1 posi tion on both sides are correctly aligned. 2. Do not apply excessive force to the user sy stem interface board while it is connected to the user sy stem. 3. The dimensions of the recommended mounting pad for the IC socket for this user[...]

22 8. When you use the emulator wit hout connecting it t o the user system, ens ure that the SW1 jumper pin is i nserted to [US ER-OFF]. W hile no pin or S W1 jumper pin is inserted to [USER-OF F], the emulator s upplies 3.3-V pow er to DrVCC, w hich is the power s upply exclusively used for USB. 9. To connect the emulator to the user system, ensur[...]

23 Section 6 Restrictions There are the following res trictions on emulation of the H8SX /1663 group when the user sys tem interface board is connect ed to the emulator. 1. The USB clock frequency is fixed to 48 MHz regardl ess of the EXTAL i nput. 2. P14 cannot be used as a port if the seri al output function has already been selected. The port pi[...]

H8SX/1663 Group E6000H FP-144L User System Interface Board HS1664ECH61H User's Manual Publication Date: Rev.1.00, June 28, 2006 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Customer Support Department Global Strategic Communication Div. Renesas Solutions Corp. © 2006. Renesas Technology Corp., All rights res[...]

Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan http://www.renesas.com Refer to " http://www.renesas.com/en/network " for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) [...]

H8SX/1663 Group E6 000H FP-144L User System Interface Board HS1664ECH6 1H User’s Manual[...]