Renesas H8/3694 manuale d’uso

2003. 12.19 H8/3694, H8/36014 Group TNP-48 User System Interface Cable for E6000 Emulator HS36 014ECN6 1H Use r’s Manu al Renesas M icrocompu ter Dev elopment Enviro nment Syst em H8 Family / H8/3 00 H Tiny Serie s Rev.1. 00[...]

Cautions Keep safety first in your circ uit designs ! 1. Renesas Technology Corp. put s the maxi mum effo rt into maki ng semicon ductor product s better and more reliable, but the re is always the possi bility that trouble may occur with them. Trouble with semi conductors may lead to personal injury , fire or propert y damage. Remember to give due[...]

I ? IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this u ser system interface cable. • KEEP the user's manual handy for future reference. Do not atte m pt to use the user system interface ca ble unt il you fully under stand its mec ha ni s m. User Syst em Interface Cable: Throughout thi s document, the ter m [...]

II LIMITED WARRANTY Renesas warrants its user system interface cabl es to be manufactured in accordance with published specifications and free from defects in material and/or workmanship. Renesas will re pair or replace any user system interfac e cables determine d to be defective in ma terial and/or workmanship. User s ystem interface cables are w[...]

III State Law: Some states do not allo w the exclusion or li mitatio n of implied warranties or liabilit y for incidental o r consequen tial d amages, so t he ab o ve limitation or excl usion ma y not appl y to y ou. This warr ant y give s yo u spec if ic lega l rig hts, and you ma y have other rig hts wh ic h may va ry fro m state to state. The Wa[...]

IV SAFETY PAGE READ FIRST • READ this user's manual before using this u ser system interface cable. • KEEP the user's manual handy for future reference. Do not atte m pt to use the user system interface ca ble unt il you fully under stand its mec ha ni s m. DEFINITION OF SI GNAL WORDS This is the safet y alert symbol. It is used to a [...]

V W ARNING Observe the pr ecautions listed below. Failur e to do so will result in a FIRE HA ZARD and will damag e the user system and the emula tor product or will r esult in PERSONAL INJURY. Th e USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product b y yourself for e lectric sho ck prevention and quality assurance. 2. Alway[...]

i Preface Thank y ou for pu rchasin g this u ser sy stem interface cable (HS36014EC N61H) for the Re nesas’ origin al m icrocom puter H8/ 3694 group an d H8/36014 grou p. The HS36014ECN61H is a u ser sy stem interface cable th at connects an H8/3694 group, H8/36014 group E6000 em ul ator (HS3664EPI61H; herei nafte r referred to as th e em ulator)[...]

ii Contents Section 1 Configuration .................................................................................... 1 Section 2 Connection Procedures ...................................................................... 3 2.1 Connectin g User Sy stem Interf ace Cable to Em ulator Station .......................................... 3 2.2 Connec[...]

1 Section 1 Configuration CAUTION Use an NLPACK 048SD socket (manufact ured by Tokyo Eletech Corporation ) for the TNP- 48 package IC socket on the user system. Figu re 1 show s the con figu ration of the HS 36014ECN61H user s yst em in terface cable for the TNP-48 package. Figure 1 HS36014ECN61H Us er System Interface Cab le[...]

2 Table 1 lists t he HS36014ECN61H com pon ents. Pleas e mak e sure y ou h ave all of thes e compon ents w hen un packing. Table 1 HS36014ECH64H Com ponen ts No. Component Quantity Remarks 1 Cable body 1 Coax ial cable 2 Cable head 1 3 IC socket 1 For the TNP-48 package 4 Socket cover 1 For installing a TNP-48 packaged M CU 5 Screws (M 2 x 10 mm) 4[...]

3 Section 2 Connection Procedures 2.1 Con necting User System Interf ace Cable to Emulator Statio n W ARNING Observe the precautions listed below. Failure t o do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user sys[...]

4 Figure 2 Connecting User System Interface Cable to Em ulator Station[...]

5 2.2 Con necting User System Interf ace Cable to User System W ARNING Always switch OFF the user syst em and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part . Before connecting, make sure that pin 1 on bot h sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will dama[...]

6 2.2.1 Installing IC Socket After ch ecking th e location of pin 1 on the IC sock et fasten it to the u ser system before solderin g. CAUTION After confirming the locat ion of pin 1 on the IC socket, apply epoxy resin adhesive to the end of the four projections at the bott om of the IC socket , and fasten it to t he user system. Use the gui de pin[...]

7 2.2.2 Soldering IC Sock et After f astening , solder the IC socket f or a TNP -48 packag e to the user sy stem . CAUTION Be sure to completely solder th e leads so that the solder slops gently over the leads and forms solder fillets. (Use slightly more solder than the MCU.) 2.2.3 I nserting Cab le Head CAUTION Check the location of pin 1 before i[...]

8 2.2.4 Fas tening Cable Head CAUTION 1. Use the screwdriver provided fo r tightening screws. 2. The tightening torque must be 0.098 N•m or less. If the applied torque cannot be accurately measured, stop tightening when th e force required to tu rn the screw becomes significantly greater th an that needed when first tightening. If a screw is tigh[...]

9 Fasten the us er system interf ace cable head to the IC socket f or a TNP-48 package on the u ser system with the four screws (M2 x 10 m m) provided. Each screw should be tightened a little at a tim e, alternatin g betw een s crews on opposing corners. Take special care, such as man ually securing th e IC socket soldered area, to preven t the sol[...]

10 2.2.5 Fastening Cable B ody Connect the cable body to the cable h ead. Figure 5 Fastening Cable Body[...]

11 2.3 Recomm ende d Dimensions for User Syst em M ount Pad Figure 6 show s the recom m ended dim ensions f or the m ount pad (footprin t) for the us er system w ith an IC socket f or a TNP-48 packag e (NLPACK048S D: m anuf actured by Tokyo El etech Corporation). Note that the dim ens ions in f igure 6 are som ew hat differen t from those of th e a[...]

12 2.4 Dimensio ns for User S ystem Interface Cable Head The dimens ions for the u ser sy stem interf ace cable head are show n in figu re 7. ± Figure 7 Dim ensions for User System Interface Cable Head[...]

13 2.5 Resu lting Dimensions after Connecti ng User System Interface Cabl e The resulting dim ensions, af ter connecting the user sy stem in terface cable head to the u ser system , are show n in f igure 8. ± Figure 8 Resulting Dim ensions after Connecting User System Interface Cable[...]

14 Section 3 Installing the MCU to the User System CAUTION 1. Check the locat ion of pin 1 before inserting. 2. Use the screwdriver provided fo r tightening screws. 3. The tightening torque must be 0.098 N•m or less. If the applied torque cannot be accurately measured, stop tightening when th e force required to tu rn the screw becomes significan[...]

15 Figure 9 Installing M CU to User System[...]

16 Section 4 Verifying Operation 1. When u sin g the H8/ 3694 group an d H8/36014 grou p E6000 emu lator (HS3664EPI61H), t urn on the em ulator accordin g to the procedu res described in th e H8/3664 Series E6000 Em ulator User's Manual (HS 3664EPI61HE-U2). 2. Verify the user sy stem interface cable conn ections by accessing ports and ch eckin[...]

17 Figure 10 shows the sy stem clock oscillator on the user system interface cable and the su bclock input specifications. Ω Ω Ω Figure 10 System Clock Oscillator[...]

18 Section 5 Notice 1. Make sure that pin 1 on the us er system IC socket is correctly aligned w ith pin 1 on the cable head before insertin g the cable head in to the user sy stem IC socket. 2. The dimens ions of th e recomm ended m ount pad for th e user sy stem IC socket are differen t from thos e of the MC U. 3. This user sy stem interface cabl[...]

19 6. T he P 1 short connector is used for testing. Do not remove the inserted jumper pin. SW1 is a sw itch provided f or selecti on of th e H8/3694 grou p or the H8/36014 g roup. Sh ift the sw i tch to 3694 or 36014 w hen th e H8/3694 grou p or the H8/ 36014 group is in u se, respectiv ely . At defau lt, th e sw itch is sh ifte d to 36014. 36014 3[...]

H8/3694, H8/36014 Group TNP-48 User System Interface Cable for E6000 Emulator User's Manual Publication Date: Rev.1.00, December 19, 2003 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Technical Documentation & Information Department Renesas Kodaira Semiconductor Co., Ltd.  2003 Renesas Technology Corp. [...]

H8/3694 , H8/ 36014 G rou p TNP- 48 User Sy stem Inte rface C able for E600 0 Emul ator User’s Ma nual REJ10B0094-0100H[...]