POSIFLEX Business Machines TP/LT- 5800 manuale d’uso

Part 1 FCC Notes: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply wit h limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are [...]

Part 2 ALERT TO OUR HONORABLE CUSTOMERS: l Please always read thoroughly all the instructions and docum ents delivered with the product before you do anything about it. Don’t take any premature action before you have a full understanding of the consequences. l This product contains inside a Lithium battery and maybe also a sealed type Lead acid b[...]

Part 3 Standard Features: a) CPU: Eden 667 MHz or up for TP/LT - 5 6 00; C3 800 MHz for TP/LT - 5700; C3 1.0 GHz for TP/LT - 5800 ; Celeron 2.0 GHz for TP/LT - 8000 b) Jiva TP/LT - 5800 /8000 has both system fan and CPU fan with a fan control software in preload ed OS . c) An advanced slim base design supporting 2 nd LCD display or pole mount custo[...]

Part 4 m) Touch control functions : left/right button, double click, drag & draw (for Jiva TP only) n) Dual display support (per OS capability) o) VGA memory size shared from system memory (16 – 64 MB for TP/LT - 5600/5700/5800, 16 – 128 MB for TP/LT - 8000) p) Support high performance DDR DRAM with maximum memory size 1GB for TP/LT - 5600/[...]

Part 5 INSTALLATION GUIDES CAUTION: Before any installation or cable connection to the set, please always make certain that the system is turned off and the external power source to the set is removed to prevent electric hazard! Never touch any m etal pin in the connectors or circuits to avoid high voltage hazard or electrostatic discharge damage u[...]

Part 6 disconnection operation are not covered by product warranty! SEPARATING MAIN UNIT In order to settle the touch terminal properly in a point of sale system, all the cable co nnections have to be routed through its base, the stand assembly. Therefore, please observe the procedures from A to C below to separate the main unit from the stand asse[...]

Part 7 CABLE ROUTING Please route all cables through the cable passage to main unit in desktop mount application. Hold them together with the cable tie. Pass all cables (but those for HDD and UPS battery) through the cable exit to external connections. T hen fix back the bottom plate if there is no option unit to install . INSTALLING UPS BATTERY Th[...]

Part 8 in squares in lower left picture and allow the main unit to slide down the winding grooves in t he wall mount backpack - originally the base box. The stand assembly is not engaged in wall mount operation. Connect all cables coming out of the backpack into the cable cover area of main unit. The area required for wall mount application is dete[...]

Part 9 will look like the right picture. Route the VGA through the cable exit of the base stand to the main unit. Conn ect the attached power adaptor for its power source. ROUTING THE CABLES Place all the cables required for connections to the main unit except those for the integrated attachment through the front part inside the stand assembly . Be[...]

Part 10 After the battery is nearly exhausted, the user must change a new battery otherwise the system RTC and system configuration setup will be lost. SIDE & REAR TOP MOUNT UPGRADE KIT Please follow the instructions in the manuals delivered with the side mount upgrade kit: KP100, SD100 , SD200 or BC100 and the rear top mount upgrade kit PD302 [...]

Part 11 http://www.posiflex. com.tw DESKTOP MOUNTING Match the matching pegs on the back of the main unit against the matching holes on the stand assembly . First aim the matching pegs toward the upper round part of the hole and make sure that all pegs are inside the holes. Then slide the main unit down to move the pegs into the lower slot part of [...]

Part 12 plastic latchkey that is used when removing the cable cover, but be sure to turn it in the clockwise direction to lock the cover in place. Re - adjust the tilt angle of the screen for best viewing. Connect the cables to appropriate external d evice s through the cable exit at the bottom of stand assembly . Please make sure that each connect[...]

Part 13 subfolder “ drivers” in OS recovered HDD and the latest versions of these required drivers will be available on our web: http://www.posiflex .com.tw . Now please follow instructions from your system integrator for software recovery. OPERATING SYSTEM INSTALLATION This product is a highly professionalized equipment. The installation of [...]

Part 14 USING THE TOUCH POS APPLICATION ENVIRONMENT It is very important that you check the following operational guidelines: Ventilation This terminal must NOT be operated in an environment with restricted ventilation. The installation should be such that there is at least 25mm air clearance around any top or side ventilation holes. The installati[...]

Part 15 connected there but found inoperable by such messages . Emergency treatment: The battery is constructed maintenance free and leakproof. It is well protected in Jiva system as long as the ambient temperature remains below 30 ° C and the ventilation of the Jiva system remains free. However, should any accident happen and the sulfuric acid fr[...]

Part 16 LED Status System Status External Power UPS Battery Powering Up Off Off Off Not present Not possible Off Off Off Present Not allowed Green Off On No influence Allowed Blue On On No influence Not required Blue/flash On Off Activated Not required Green/rapid flash On Off Running at l ow capacity Not required Hardware Power Switch The power sw[...]

Part 17 Automatic Power On Control The system may also turn on according to some preset conditions such as Modem Ring Up and Alarm Clock Wake Up or LAN Wake Up. To utilize Modem Ring Up o r Alarm Clock Wake Up function, the user should enter the CMOS setup by pressing “Del” key at system boot up, choose for “PM Wake Up Events” in “Power M[...]

Part 18 SERIAL PORTS – COM1/2/3/4 In Jiva system , there are 4 serial ports available. All the serial ports can supply a +5 V DC through pin 9 after proper jumper setting change. All 4 ports are standard RS232 serial ports as stat us at delivery . When a serial Modem is to be used in Jiva system , it is most recommended to use COM2 or COM3 or COM[...]

Part 19 TOUCH PANEL (for TP models only ) All paragraphs below are applicable in TP - 5615, TP - 57 15, TP - 5815 or TP - 8015 only. The user of LT - 5615, LT - 5715, LT - 5815 or LT - 8015 can ignore them and consider this user ’ s manual ends here. Mouse Emulation The touch panel in Jiva TP system uses PS2, RS232 or USB interface. When its driv[...]

Part 20 sticky button tool in the program group “ Posiflex USB Touch Tools ” is installed in the preloaded Windows system with a USB interface touch panel controller. This program can also be ob tained by download from the POSIFLEX web site. 警告使用者 這是甲類的資訊產品，在居住的環 境中使用時，可能會造成射頻干[...]