PGS K-30 manuale d’uso

R Models K-30 and K-40 Gas Grill click here for Legacy Series ASSEMBL Y , OPERA TING & MAINTENANCE INSTRUCTIONS (SHOWN WIT H OPTIONA L SIDE BURNER AND INFRA -BROIL KIT) PACIFIC GAS SPECIALTIES CORPORATION P.O. BOX 16097, IRVINE, CALIFORNIA 92623 Phone (949) 757-7723  FAX (949) 474-5559 Please note: We have made our catalogs , specification s[...]

TABLE OF CONTENTS Safety Responsibilities, Warning Symbol ................................................................................................. Page 2 Grill Model Identification (Location of Serial Number) .............................................................................. Page 3 Very Important Safety Tips & Warnings ....[...]

3 SPECIAL ATTENTION: THIS SYMBOL NOTES SAFETY RELATED ITEMS OR PRODUCT WARNINGS IT IS YOUR RESPONSIBILITY TO: ASSEMBLE, INSTALL, LEAK CHECK, CARE AND OPERATE YOUR GAS GRILL. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. FOR YOUR SAFETY IF YOU SMELL GAS: 1. SHUT OFF GAS TO THE APPLIANCE. 2. EXTINGUISH ANY OPEN FLAME. 3. OPEN LID. 4. IF ODOR CONTINUE[...]

VERY IMPORTANT SAFETY TIPS AND WARNINGS PGS is most concerned about the safe us e of our product. The following two pages are a summarization of the safety tips found throughout this manual. Please take the time to re view them, as they are crit ical in the enjoyable use of your grill. Improper assembly, neglect, or insufficient care of your PGS ga[...]

5 • Never lean over hot grill surface or look directly in to grill when attempting to light. The grill hood must be opened fully when lighting. Be sure that a ll family members are aware of safe li ghting and operating proc edures for the grill. • If a professional installer or dealer installs the grill, be su re that he shows you where y our g[...]

should occur, turn the valves to the “OFF” position on your grill head, then the valve on the tank. Wait tw o minutes and then open the valve on the tank BEFORE turning the valves of your grill head. Alw ay s turn on the valve at the top of your tank and then the valves to your grill head to the “ON” position. GAS Both natural gas (NG) and [...]

PROPANE CYLINDER FILLING AND HANDLING SAFETY TIPS • Be certain tank is equipped with an overfill protection device. • Do not modify hose or LP fittings. Contact a local dealer or distributor if tank, hose or fittings need replacement. • If it is evident there is excessive abrasion or wear, or the hose is cut, it must be replaced prior to the [...]

LP-Gas Tank Specifications: GRILL HEAD: Entire BBQ grill (lid & pit) that can be mounted on a variety of options. Weight (filled) 40 lbs. (18.14 kg) Capacity 4.5 gallons 8 Diameter (outside) 12 1/8" (30.8 cm) Height 18" (45.7 cm) GRILL MOUNT : Supports gas grill head, can be a post mount, pedestal mount (stationary or mobile) or built[...]

YOU WILL NEED THE FOLLOWING TOOLS TO ASSEMBLE YOUR PGS GAS GRILL: 1 - Mallet or Hammer 1 - Med. Phillips Head Screw Driver 2 - 6" Adjustable Wrenches 1 - Small Ro ll of Teflon Tape (Natural Gas Only) 50% Soap and Water Solution 1 - Spray bottle or brush Having these additional tools on hand w ill make assembly easier : 1 - 1/2" Socket and[...]

DRAWINGS OF NUTS & BOLTS AND FASTENERS REF # DESCRIPTION (QUANTITY) REF # DESCRIPTION (QUANTITY) BASE TO PEDESTAL COLLAR BOX TO PEDESTAL AND CONTROL PANEL 1. 5/16 X 3/4" BOLT (6) 13. 8 X 1/2” SHEET METAL SCREW (2) 2. 5/16” WASHER (6) 14. TINNERMAN CLIP (2) FEEDLINE 3. 5/16” LOCK WASHER (6) 15. FEEDLINE MOUNTING CLIP (1) 4. 5/16” NU[...]

PART NUMBERS AND DESCRIPTIONS PLEA SE NOTE: A LL PA RTS MA Y NOT COME WITH A LL MOUNTING OPTIONS REF # DESCRIPTION QTY MODEL K-40 MODEL K-30 1 UPPER GRILL CASTING 1 140125 130125 2 LOWER GRILL CASTING 1 140120 130120 3 WARMING RACK 1 140200 130200 4 COOKING GRID 2 140140 130140 5 ROCK GRATES (Not shown) 2 140170 130170 6 BURNER ASSEMBLY 1 140105 13[...]

PGS GAS GRILL PARTS BREAKDOWN GRILL HEAD LID TO GRILL HEAD SIDE SHELVES TO GRILL HEAD (OPTIONAL) COLLECTOR BOX LCS/LCB FOR IGNITOR CONTROL PANEL TO GRILLHEAD GREASE TRAY CONTROL PANEL STIFFENING BRACKETS CAGE NUT K30 BURNER IN-GROUND COLLAR BOX 48” POST K40 BURNER PEDESTAL TO BA SE STAINLESS (CART OR PA TIO BASE) STEEL TUBING A CCESS DOOR STAINLE[...]

CHECK LIST OF GRILL BOX CONTENTS IF YOU PURCHASED A "B" PED (Black Pedestal Kit) YOU WILL FIND 1. REMOVE ALL CONTENTS FROM BASE AND PEDESTAL OR 48" POST BOX. YOU WILL FIND: All parts listed above in the "S" Ped box except pedestal and: IF YOU PURCHASED AN LC (Liquid Propane Cart) Qty 1 Black Galvanized Steel Pedestal YOU WI[...]

Be sure that the fuel source designated on your grill head is the same as that of the support system. DO NOT USE A GRILL HEAD EQUIPPED FOR NATURAL GAS WITH LP GAS OR THE OPPOSITE . Maximum inlet pressure from System LP cannot exceed 11" W.C. The proper orifices and valving for each gas is contained in the grill head. Maximum pressure for Natur[...]

9. TEST ALL FITTINGS FOR LEAKS. BEFORE ATTEMPTING TO LIGHT GRILL, BE CERTAIN BOTH CONTROL PANEL VALVES ARE IN THE OFF POSITION. TURN GAS SUPPLY ON AT THE SOURCE AND CHECK ALL CONNECTIONS WITH A SOLUTION OF 50% LIQUID SOAP, 50% WATER. SOLUTION CAN BE SPRAYED ON WITH A SPRAY BOTTLE OR PAINTED ON ALL CONNECTIONS WITH A BRUSH. IF BUBBLES APPEAR, TURN O[...]

K-40 4. Figure 6 Control Panel/ Feedline to Valve Connection Figure 4 Installation of Cage Nuts on Pedestal ORIFICE ENGAGEMENT 4. Place lower grill casting on top of pedestal lining up four bolt holes (located ju st above air vents) with cage nuts just installed (see Fi g. 5). Then insert the 4- 1/4" X 20" X 1 1/4" hex bolt each with[...]

THIS CONNECTION WILL REQUIRE LEAK CHECK UPON ASSEMBLY COMPLETION. (see Fig. 18). 8. Attach feed line mounti ng clip to pedestal using #8 X 1/2" S.S. machine screw. BE SURE TO ALIGN SCREW TO AVOID STRIPPING THREADED NUTSERT. 9. Remove "Sure Start" Ignitor module from the underside of control panel by unscrewing black ring. Remove rear[...]

6. Attach twin lid side "Stay Cool" handles using 5/16" X 3/4" bolt and star washer, tighten securely. 7. Slide grease tray into slot at top rear of pedestal. Tray must be tilted up before inserting in. 8. If you purchased a LC base kit you will need to attach the tank strap to the back of the cart. Attach as follows: Screw one [...]

Figure 17 Leak Checking the Valve Connection 4. If no gas leaks appear (bubbles), turn off gas supply and continue assembly. IF YOU ARE UNABLE TO STOP A LEAK, CONTACT YOUR LOCAL DEALER FOR ASSISTANCE BEFORE PROCEEDING. Figure 15 LP Hose/Regulator Connection 5. If there are no gas leaks, attach the collar box with AGA/CGA rating sticker attaching to[...]

LIGHTING YOUR GRILL IF THE GRILL STILL FAILS TO LIGHT, CHECK THE GAS SUPPLY. YOU COULD BE OUT OF LP GAS OR THE MAIN GAS SUPPLY FOR NATURAL GAS MAY HAVE BEEN TURNED OFF. IF THE LP TANK HAS GAS OR THE NATURAL GAS IS TURNED ON AND THE GRILL STILL WILL NOT LIGHT: CHECK THE ELECTRONIC IGNITOR TO MAKE SURE IT IS SPARKING. IF NOT, CHECK THE BATTERY IN THE[...]

After cleaning burner assembly and the lower casting of grill, reinstall burner to lower casting. In many areas, spiders or small insects have been found to create "flashback" problems. The spiders spin webs and/or insects build nests in the grill's venturi tube(s). The web and/ or nests can lead to gas flow obstruction, which c an d[...]

BEFORE LIGHTING YOUR GRILL: TURN YOUR GAS SUPPLY (LP OR NAT) ON AND TEST ALL FITTINGS FOR LEAKS. BEFORE ATTEMPTING TO LIGHT GRILL, BE CERTAIN BOTH VALVES ARE IN THE OFF POSITION. BE CERTAIN THAT YOUR GAS SUPPLY IS OFF AND YOUR GAS FEED LINE HAS BEEN BLED OF ANY FUEL. WHEN REINSTALLING BURNER, BE CERTAIN THAT THE BURNER VENTURIS ARE ENGAGED ON THE V[...]

PLEASE NOTE: IMPROPER ORIFICE SIZE COULD RESULT IN EITHER INSUFFICIENT OR EXCESS GAS GOING TO BURNER, AND MAY POSE A SAFETY RISK. HELPFUL TIPS 1. Before using your grill for the first time, please light and turn both burners on HI heat for ten to fifteen minutes. This will burn off any oils that are on new surfaces. Before grilling, we suggest putt[...]

FLAME ADJUSTMENT TIPS Your PGS burner has been designed to operate efficiently under widely va rying operating conditions and is adjusted at the fact ory for proper operation so no adjustments should be required. Occasionally, vibration during transport or variations in local fuels and gas pressure, altitude, or other external conditions might requ[...]

PGS ACCESSORIES To more fully enjoy your gas grilling experience, PGS has des igned and manufactures a vari ety of accessories and barbecue Covers (not pictured). Please find a brief description of PGS accessories below: INFRA-BROIL KIT The PGS Infra-Broil Kit comes as a standard feature on our models K60, K40 ULTRA and K40 Delux and may be purchas[...]