Pelco ICS-DO111ABK manuale d’uso

INST ALLA TION ICS-DO111ABK Integrated Camera System MR5000 Series Public V iewing System C2495M-A (1/06)[...]

Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (includi[...]

Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC, Class B (except auto iris models) RADIO AND TELEVI[...]

Description Designed specifically for the MR5000 Series public viewing system, the ICS-DO111ABK integrated camera system packages a camera and lens into a small, discreet, high-security dome. Pelco’ s MR5000 Series public viewing system is specifi cally designed for retail applications to provide a clear , visual warning to potential shoplifter[...]

Installation PREPARE VIDEO AND ELECTRICAL CABLING 1. T emporarily remove the bottom end cap of the MR5000 Series mount if the end cap is installed. 2. Feed the 42-inch video cable (provided) through the monitor feedthrough hole in the mount arm and out the bottom end of the mount arm. 3. Pull power wires through the ICS-DO111ABK feedthrough hole lo[...]

INSTALL THE ICS-DO111ABK TO THE MR5000 MOUNT Follow the steps below to install the ICS-DO111ABK to the MR5000 mount: 1. Align the adapter plate with the cover. Position the cover so that the notch on the side of the cover faces the back of the MR5000 mount. ADAPTER PLATE COVER 10-32 x 0.375-INCH SCREWS AND WASHERS BACK BOX 8-32 x 0.375-INCH SCREWS [...]

3. Do the following to install the back box inside the cover of the ICS-DO111ABK: a. Feed the video cable and power wires attached to the ICS-DO111ABK back box through the cover and adapter plate of the ICS- DO111ABK. b. Rotate and position the back box so that the conduit plug on the side of the box is located on the opposite side (180 degrees) fr[...]

4 Install Camera WARNING: Heater elements could be hot! When camera power is on, use caution when adjusting the camera. This applies to all models. 1. Some indoor installations do not require a heater . If the installation does not require a heater , remove the heater board from the camera assembly. T o remove the heater press on an end of the boar[...]

5. Always make sure the tab on the camera bracket is pointing out of the enclosure (away from the ceiling or wall). Gently squeeze the bracket, place it against the groove inside the back box, and gently release. Proper camera orientation: CAMERA BRACKET T AB AL WA YS POINTS TOP OF OUT OF THE CAMERA ENCLOSURE CAMERA BRACKET T AB AL WA YS POINTS OUT[...]

Install Dome and T rim Ring 1. Align the screw holes in the trim ring with ADJUSTMEN T those in the Camclosure base. GROOV E 2. Domes with Liners (only) – DOME LINER Position the viewing window over the lens of the camera by doing the following: LOOSEN SCREWS a. Loosen the three Phillip screws located in the dome. b. Insert the blade of a standar[...]

AUTO IRIS LEVEL ADJUSTMENT If you have a varifocal lens or fi xed focal length lens with an auto iris, you can adjust the level setting to increase or decrease brightness. VARIFOCAL LENS FIXED LENS IRIS LEVEL ADJUSTMENT AUTO IRIS LEVEL ADJUSTMENT FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS WARNING: Heater elements could be hot! Whe[...]

SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS Refer to the switch drawing. The switch is located next to the lens. Automatic backlight compensation (factory setting) is used under varying lighting conditions (such as outdoors) or fi xed lighting conditions where there are no bright spots that darken other picture details. Manual backl[...]

SWITCH SETTINGS FOR V ARIFOCAL LENS The high resolution camera with varifocal lens and auto iris is confi gured at the factory for automatic exposure. 1 AWB Automatic white balance 2 GAM Gamma function F ACTORY SETTINGS 3 AGC Automatic gain control 4 ESC Electronic shutter control 5 BLC Backlight compensation 6 AE Functions FL Flickerless = SWITCH[...]

Specifications General Operating T emperature -50° to 122°F (-46° to 50°C) De-ices to 25°F (-4°C) Cable Entry 3/4-inch (1.91 cm) conduit fi tting and 3/4-inch (1.91 cm) opening for NPT threaded pipe Pan/T ilt Adjustment Manual; 360° pan; 180° tilt Construction Aluminum with steel camera mounting bracket and polycarbonate Finish Environmen[...]

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex ® Series p[...]

Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO 9001 United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East[...]