LevelOne IFE-0500 manuale d’uso

LevelOne IFE-0500 4-Port PoE + 1-Port TP Industrial Fast Ethernet Switch User Manual V er . 1.0.0-071 1 1[...]

FCC W arning This Equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part 15 of t he FCC rules. These limits are designed to provide reasonable protection against harmful in terference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy . It may c[...]

Content INTRODUCTION ...................................................................................... 4 F EA TURES ................................................................................................................. 4 P ACKAGE C ONTENTS ..............................................................................................[...]

Introduction The 4-Port PoE + 1-Port TP Industrial Fast Ethernet Switch is a cost-effective solution and meets the high reliability requirement s demanded by indus trial applications. In addition, the industrial switch provides the PoE function for kinds of Powered Devices to receive power as well as data over the RJ-45 cable. Features  System I[...]

Package Content s Please refer to the package content s list below to verify them against the checklist.  IFE-0500  CD Manual  Pluggable T erminal Block (att ached on the switch)  2 wall mount plates with screws  One DIN-Rail (attached on the switch) Compare the content s of the i ndustrial switch with the standar d checklist above. [...]

Hardware Description In this paragraph, the Industrial switch’ s hardware spec, port, cabling information, and wiring installation will be described. Physical Dimension 4-Port PoE + 1-Port TP Industrial Fast Et hernet Switch dimension (W x D x H) is 30mm x 95mm x 140mm Front Panel The Front Panel of the 4-Port PoE + 1-Port TP Industrial Fast Ethe[...]

T op V iew The top view of the 4-Port PoE + 1-Port TP Industrial Fast Ethernet Switch has one terminal block connector of two DC power inputs. T op V iew of the IFE-0500 Indus trial Fast Ethernet Switch 7[...]

LED Indicators The diagnostic LEDs located on the front pa nel of the industrial switch provide real-time information of system and optional status. The following t able provides the description of the LED status and their meanings for the switch. LED Color Description On Power input 1 is active P1 Green Off Power input 1 is inactive On Power input[...]

Port s  RJ-45 ports The UTP (RJ-45) Fast Ether net port s will auto-sense for 10Base-T or 100Base-TX connections. Auto MDI/MDIX me ans that the switch can connect to another switch or workstation without changing straight thr ough or crossover cabling. See the below figures for straight through and crossover cable schematic.  RJ-45 Pin Assign[...]

S traight Through Cable Schematic Cross Over Cable Schematic 10[...]

Cabling  T wisted-pair segment c an be connected with unshielded twisted p air (UTP) or shielded twisted pair (STP) cable. The cable must comply with the IEEE 802.3u 100Base TX st andard for Category 5. The cable between the converter and the link partner (switch, hub, workst ation, et c.) must be less than 100 meters (328 f t.) long. 11[...]

Wiring the Power Input s Please follow the steps below to insert the power wire. Insert the positive and negative wires into t he V+ and V - contacts on the terminal block connector . T ighten the wire-clamp scr ews for preventing the wires from loosing. 12[...]

Wiring the Fault Alarm Cont act The fault alarm contact is in the middle of terminal block connector as the picture shows below . When the wires are inserted in to ports 3 and 4, t hey automatically detect the fault status in the event of a power failure by forming an open circuit. An example for the fault ala rm contact is shown as below: Insert t[...]

Mounting Installation DIN-Rail Mounting The DIN-Rail is screwed on the i ndustrial switch when out of factory . If the DIN-Rail is not screwed on the industrial switch, please see the following pictures to screw the DIN-Rail on the switch. Follow the step s below to hang the industrial switch. 1. Use the screws to screw the DIN-Rail on the rear sid[...]

4. Then, lightly push the DI N-Rail into the track. 5. Check if the DIN-Rail is tightened on the track or not. 6. T o remove the industrial switch from the track, reverse steps above. 15[...]

W all Mount Plate Mounting 1. Follow the steps below to mount the industrial switch wit h wall mount plate. 2. Remove the DIN-Rail from the industrial switch; loose the screws to remove the DIN-Rail. 3. Place the wall mount plate on the rear panel of the industrial switch. 4. Use the screws to screw the wall m ount plate on the industrial switch. 5[...]

Hardware Installation In this paragraph, we are going to mention how to install the 4-Port PoE + 1-Port TP Industrial Fast Ethernet Switch and the installation point s to be attended to it. Inst allation Step s 1. Unpack the Industrial switch p acking. 2. Check if the DIN-Rail is screwed on the Industrial switch or not. If the DIN-Rail is not screw[...]

Network Application This segment provides the sample to help user have more actual idea of industrial switch application. For a sample applicati on of the industrial s witch, see the figure below . 18[...]

Troubleshooting  V erify that is using the right power cord/adapter (DC 48V), please don’t use the power adapter with DC output voltage hi gher than 48V , or it will burn this equipment down.  Select the proper UTP/STP cable to constr uct your network. Please check that is using the right cable. Use unshielded twiste d-pair (UTP) or shield [...]

Technical Specification The IFE-0500 4-Port PoE + 1-Port TP Indus trial Fast Ethernet Switch technical specifications is shown as below . IFE-0500 4-Port PoE + 1-Port TP Industrial Fast Ethernet Switch Standard IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX Fast Ethernet IEEE802.3x Flow Control and Back Pressure IEEE802.3af Power over Ethernet[...]

Power Consumption 3.4W att s (without PoE); 57 W a tts (Full load with PoE) Inst allation DIN rail kit for DIN-type cabinet install and wall-mount ear for wall mounting Operating T emp. -10 ℃ to 60 ℃ (14 ℉ ~ 140 ℉ ) Operation Humidity 5% to 95% (Non-condensing) Storage T emperature -40 ℃ to 85 ℃ Case Dimension IP-30, 30 mm (W) x 95 mm ([...]