Kuhn Rikon 30-100 manuale d’uso

8” Bench Drill Press Model: 30-100 Owner ’ s Manual For more information: www .rikontools.com or info@rikontools.com For Parts or Questions: techsupport@rikontools.com or 877-884-5167 Record the serial number and date of purchase in your manual for future reference. Serial number: Date of purchase: Part # 30-100M2[...]

Safety W arnings IMPORT ANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be followed at all times. There are certain applications for which this tool was designed. We strongly recommend that this tool not be modied and/ or used for any other application other than that for[...]

SA VE THESE INSTRUCTIONS. Refer to them often. 3 California Proposition 65 W arning W ARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.Y our risk from exposure to these chemicals v[...]

T able of Contents Safe ty W arni ngs. ... .... ... .... .... ... .... .... ... .... .... ... .... ... .... .... ... .... .... ... .... .... ... .... .... ... .... ... .... .... ... .... .... ... .... .... ..2 -3 Special Safety Rules For Drill Presses............................................................................................. 3 S p[...]

5 Contents of Package Unpacking and Checking Contents Item Description 1 Drill Press Head 2 Base 3 T able 4 1/2” Chuck 5 Chuck Key 6 Hardware Bag (See Contents Below) 7 Feed Handle 8 Column Item Description 9 T able Lock Handle 10 Column Mounting Bolts 1 1 3mm Hex Wrench 12 4mm Hex Wrench 13 6mm Hex Wrench 14 Feed Handle Bolt 15 Owner ’s Manual[...]

6 Getting to Know Y our Drill Press 1 2 3 6 7 8 10 1 1 12 Item Description 1 Base 2 T able Lock Handle 3 T able 4 Column Support T ube 5 Handle Return Spring 6 Depth Stop 4 5 Item Description 7 Belt Cover 8 Motor 9 Feed Handle 10 Chuck 1 1 Chuck Key Holder 12 Switch 9[...]

Unpacking and Clean-up 1. Carefully nish removing all contents from shipping carton. Compare contents of the shipping carton with the list shown on page 5. Place parts on a protected surface. 2. Report any shipping damage to your local distributor . If parts are missing contact RIKON customer service at 877-884-5167 or techsupport@rikontools.com[...]

8 Assembly 3. Slide the drill press head over the column. (Fig.03) 4. Center the drill press head over the table and base. T ighten the drill press head into position by locking the two hex screws on the side of the casting. (A-Fig.04) Fig.03 Fig.04 5. Next, slide the 1/2” chuck (A-Fig.05) over the pre-installed spindle (B-Fig.05). Open the chuck[...]

9 Assembly 6. The feed handle (A-Fig.06) is secured to the feed shaft with the supplied Allen bolt (B-Fig.06). Fig.06 A B 7. Depth Stop: The depth stop and scale are found on the left side of the switch box. T o adjust, lower the drill chuck until pointer shows desired depth on the scale . Loosen the lower nut on the threaded shaft (A-Fig.07) until[...]

Assembly 10 Fig.09 10. Loosen the motor lock knob (A-Fig.10). Move the motor (B-Fig.10) manually toward the feed handle to take tension off of the belt. Fig.10 A B 1 1.Move the drive belt to the desired speed position, refer to speed chart inside belt cover . Manually move the motor away from the feed handle until the belt is tensioned, tighten mot[...]

T roubleshooting 1 1[...]

Use this section to record maintenance, service and any calls to T echnical Support: 12 Notes W ARNING: This machine must be grounded. Replacement of the power supply cable should only be done by a qualied electrician. Wiring Diagram[...]

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in acco[...]

Explosion Diagram 14[...]

Parts List 15 KEY No. Bushing-Rubber Knob Screw-Pan Hd.M5x0.8-1.2 Belt-”V” 5/16x26 Guard w/Labels Screw-W asher Hd. Ring Retaining Bearing-Ball 17mm Spacer Insert-Pulley Pulley-Spindle Nut-Pulley Clamp Cord Screw-Pan Hd.M5x.08-16 W asher ,Foam 30-100-1A 30-100-2A 30-100-3A 30-100-4A 30-100-5A 30-100-6A 30-100-7A 30-100-8A 30-100-9A 30-100-10A 3[...]

[...]

[...]

Explosion Diagram 18[...]

KEY No. Gasket-Quill Bearing-Ball 12mm T ube-Quill Screw-Pan M5x0.8-20 Collar-Stop Ring Retaining Shaft-Spindle Chuck Key-Chuck Nut-Hex M6x1.0 Nut-Hex M5x.08 Rod-Stop 30-100-1C 30-100-2C 30-100-3C 30-100-4C 30-100-5C 30-100-6C 30-100-7C 30-100-8C 30-100-9C 30-100-10C 30-100-1 1C 30-100-12C Description Parts List 19[...]

Explosion Diagram 20[...]

KEY No. Support-T able w/Scale Support-Lock Handle T ube/Support Base Screw-Hex Hd. M8x1.25-20 Screw-Hex Hd. 1/2-12x7/8 T able 30-100-1D 30-100-2D 30-100-3D 30-100-4D 30-100-5D 30-100-6D 30-100-7D Description Parts List 21[...]

5-Y ear Limited W arranty RIKON Power T ools Inc. (“Seller”) warrants to only the original retail consumer/purchaser of our products that each product be free from defects in materials and workmanship for a period of ve (5) years from the date the product was purchased at retail. This warranty may not be transferred. This warranty does not a[...]

Notes[...]

For more information: 16 Progress Rd Billerica, MA 01821 877-884-5167 / 978-528-5380 techsupport@rikontools.com www .rikontools.com Copyright RIKON Power T ools, Inc. 201 1 Printed in China 7/1 1[...]