CrimeStopper RS-850 manuale d’uso

RS-850 Remote Engine Starting System INSTALLATION INSTRUCTIONS PRE-INSTALLATION CONSIDERATIONS To ease and reduce installation time, we suggest you R EAD THIS MANUAL and consider the following points before beginning your installation: BEFORE BEGINNING, check all vehicle manufacturer cautions and w arnings regarding electrical service (AIR BAGS, AB[...]

TABLE OF CONTENTS Pre-Installation Considerations…………...……...………………………………………………………………Front Cover Cautions & Warnings…….…………..….……..…..……………………………………………………………….…..……2 Wiring……..…………………………..[...]

WIRING 2 PIN PLUG-PROGRAM/OVERRIDE SWITCH: This switch is used for programming features, transmitters, and valet mode. 2 PIN PLUG-(OPTIONAL) LED: The LED is used as an indicator for Valet, Programming, and for use as security deterrent with the optional ANTI- GRIND/STARTER DISABLE feature installed. Mount in a visible location on the dash or in the[...]

WIRING PIN 4: YELLOW/BLACK: (-) ANTI-GRIND/STARTER KILL OUTPUT (OPTIONAL) Use this wire for the negative side of the Anti-Grind/Starter Dis able relay. It can also be used as a sensor disable circuit for a host alarm. This output activates whenever a remote start is requested, and when the vehicle is remotely locked with the transmitter. (See diagr[...]

WIRING PIN 8: PINK: (+12V) DIESEL GLOW PLUG INPUT Connect Pink wire to indicator circuit that shows +12 volts while the “WAIT TO START LAMP ” is on. When this wire is used, the system will wait until light turns off before attempti ng a remote start. Note: For vehicles that have a Negative Wait to Start lamp, relay is required to convert the si[...]

IGNITION SWITCH WIRING PA R K I N G LIGHTS FUSE RED WHI TE 30A FUSE RED +10A MAX. 30A + - BROWN PINK FUEL ENGINE BA TTER Y PUMP ECU GRA Y + ST ARTER - COI L IGN 1 AC C Heat/AC Diagra m Not to Sca le. For il lustrat ion purp oses only . Y our vehicl e may differ . IGN. S witc h 6[...]

POWER DOOR LOCK WIRING PIN 1: BLUE: (-) Negative pulse for UNLOCK Crimestopper Door Lock Accessories: CS-6600DLM: Dual-relay plug-in module for Reverse Polarity, Positive, or Aftermarket Motors. CS-6500DLI: Plug-in pulse inverter that converts the Negative outputs of the system to Positive type for Positive Door Lock systems. CS-610S1: Aftermarket [...]

BASIC DOOR LOCK DIAGRAMS NEGA T IVE TRIGGER DOO RLOCK WIRING POSITIVE TRIGG ER DO ORLOCK WIRING GREEN GREEN FUSED RED +12V RED BLUE + BLUE 86 85 86 85 87 87 30 87A 30 87A FAC T O RY FAC T O RY L L POWER POWER LOCKING LOCKING UL UL RELA YS RELA Y S A FTERM A RKET MOTOR/DOOR LOCK WIRING REVERSE POL A RITY DOO R LOCK WIRING GREEN GREEN FUSED FUSED RED[...]

“SMART TACHLESS” MODE Your CoolStart system includes a unique voltage monitor called “S mart Tachless” mode. This mode allows this unit to efficiently start an engine without the use of a tach signal wire. These modules actively monitor the voltage level of the vehicle to control the starter motor each time a remote start is requested. IMPO[...]

TACH (RPM) REFERENCE MODE / TACH FINDER MODE / TACH PROGRAMMING Tach Reference Mode provides reliable remote start ing performance though engine speed sensing. When using Tach Reference Mode, the Red/White wire is used for Tach signal [Engine RPM] input. Most modern engines include various points where the Engine Speed [Tach] or A/C signal may be o[...]

TRANSMITTER PROGRAMMING Note: All transmitter codes must be learned at time of programming!! The RS800 allows storage of up to 4 different transmitter codes. 1. Open Hood. (Ground Gray wire.) 2. Turn key to the ON position. 3. Press Programming button 4 times, then after a few seconds the unit will flash the parking lights 4 times. 4. Press button [...]

OPTION PROGRAMMING IMPROVED: Now you can program multiple options in one sessi on if you start with the lowest option and continue on to higher options [if needed] without repeating the steps #1-3. For example, you can change Op tion #2 to “ON” by pressing the lock button, then you can continue pressing the program bu tton to get to a high numb[...]

OPTION PROGRAMMING OPTION DESCRIPTIONS: 1. NOT USED: No Option 2. Door Lock Pulse Time: Controls the amount of time for lock/unlock pulse. The standard setting is 0.75 for most vehicles. A 3 sec. setting is required for 1980’s/90’s European Vacuum or Pneumatic door lock systems. 3. Double Unlock Pulse: The unit will send 2 unlock pulses when th[...]

REMOTE START TROUBLESHOOTING “Before You Call Section” UNIT FLASHES LIGHTS ONCE AND WILL NOT ATTEMPT A START: The unit is in Valet mode. Turn IGN ON, press and hol d valet/programming button for about 4 seconds until LED goes out. The unit is now out of valet mode and should perform a remote start. UNIT FLASHES LIGHTS TWICE AND WILL NOT ATTEMPT[...]

TRAN SMISSION PROGRAM/ OVERRIDE PA R K I N G LIGHTS SW ITC H ECU RS-850 ANT ENNA/ RECEIVER PLUG LED COIL + - (-) UNLOCK OUT PUT +12 V FOR RELA Y S 12A MAX. (-) LOCK OUT PUT ENGINE ECU GREEN BLUE RED WHITE FUEL PUMP PINK RED H/V/AC CONTROL BROWN GRA Y RED YELLOW (-)IGN OUT IGN 1 RED/W HITE T ACH INPUT ORANGE/BLACK: (-) OEM DISARM (-) HOOD SWITCH GRA[...]

ONLINE TECHNICAL SUPPORT www.crimestopper.com/techweb03.html www.crimestopper.com email@crimestopper.com Phone (800) 998-6880 FAX (805) 581-9500 © 2003 Crimestopper Security Products[...]