CDA EDD61 manuale d’uso

Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .care@cda.eu W : www .cda.eu www .cda.eu edd61 & edd91 Extractors Installation, Use and Maintenance[...]

2 Important The CD A Group L td cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CD A reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment. This appliance is no[...]

3 IMPORT ANT INFORMA TION FOR CORRECT DISPOSAL OF THE PRODUCT IN A CCORD ANCE WITH EC DIRECTIVE 2002/96/EC. At the end of its working life, the product must be taken to a special local authority waste collection centre or to a dealer providing appliance recycling services. Disposing of a household appliance separately avoids possible negative conse[...]

4 • Steam cleaners must not be used when cleaning this appliance. • The performance of your extractor will vary depending on a number of factors. These include: type of extraction, length of ducting, room volume, ventilation available and cleanliness of the filters.[...]

5 Using Y our Extractor For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for appro ximately 15 minutes after the end of cooking. Control Panel A - O key B - On / “+” key C - Speed selection display (4 LED’ s) D - “-” key E - Timer key T o switch on the extractor or to incre[...]

6 T o decrease the speed at any time • T ouch the “-” key a few times, until the required speed is reached. T o switch o the extractor • T ouch the “O ” key : The moving panel will descend to its rest position and the appliance will continue extracting until its height drops below appro x. 180mm, at which point the extraction will[...]

7 Energy saving feature This extractor is fitted with an energy saving feature that automatically reduces the motor speed if it is left on the highest setting . When the motor speed is set to the fourth level, it will automatically switch to level three after six minutes of operation. Care and Maintenance IMPORT ANT : DO NO T PERFORM MAINTENANCE O[...]

8 T o remove and replace the grease filters • T ouch the “On/+” key so the moving panel raises to its full extent, then isolate the power supply so it stays raised. • By pulling the two top corners of the front panel (Fig. 2) at the same time, it will be released and pivot toward you. • The grease filters can then be pulled forward and [...]

9 Mounting your Extractor When the extractor is to be installed behind an electric or gas hob, the minimum distance between the hob and extractor must ex ceed 50mm. In the case of a gas hob, the minimum distance from any burner to the back of the hob must also be 65mm. If the instructions provided with your gas hob state that the required distance [...]

10 T roubleshooting Y ou observe that Possible Causes What should you do ? The hood does not work. There ia a power outage. Check the power supply . The 9 pin connector is faulty or misconnected. Check the orientation and security of the 9 pin connector . The internal breaker has tripped. Press the red reset key on the electronic bo x. The output i[...]

11 Ducting and V entilation • For best performance and lowest noise output, we recommend the use of 150mm ducting. Use of any smaller ducting will reduce performance and increase noise. • The length of ducting should not ex ceed 5 metres in total. • Limit the use of elbows in the ducting to a minimum: Bear in mind that each elbow imposes a si[...]

12 Installation Note • W e recommend that you seek the help of another individual when installing this product. • The fixings supplied are suitable for most installations. It is the responsibility of the installer to ensure that the fixings are suitable for the cabinets in the property . Installation 1) Prior to installation, check that all p[...]

13 2) Before making a cut-out in the kitchen cabinets or worktop, ensure that there are no structural (or other) obstructions that would hinder installation. Ensure that the cabinet dimensions are sucient to accommodate the extractor , allowing for the specified clearance between the final installed positions of the extractor and the hob. 3) B[...]

14 6) L ocate the support frame (trim piece); apply a narrow bead of silicone sealant to the underside of this (Fig. 7). Position this around the cut-out in the worktop (Fig. 8). 7) L ower the main body of the downdraft extractor through the support frame and into its fitted position. 8) Fix the downdraft extractor inside the cabinet using the spe[...]

15 9) R efit the motor unit to the main body of the downdraft extractor . This may be positioned with the outlet facing vertically upward or downward. 10) Connect suitable ducting to the extractor outlet. See page 11 for ducting requirement details. 11) Position the metal bo x containing the electronic components in the cabinet, no closer than 65m[...]

16 14) Open the filter cover (Figs. 14 & 15) then remove the grease filter package identified in Fig. 15. 15) Position the grease filters as shown in Fig. 16. Downdraft Calibration After installation it is necessary to calibrate the downdraft mechanism. • Connect the power supply to the extractor . • T ouch the “On/+” key to start t[...]

17 Mains Electricity Connection W arning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 3Amp fused plug. T o change a fuse in this type of plug, follow the steps below: 1. R emove the fuse cover and fuse. 2. Fit replacement 3A fuse, A ST A approved to BS 1362 type, into the fuse cover . 3. Replace[...]

18 As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:- • The wire which is coloured GREEN and YELL OW must be connected to the terminal which is marked with letter (E) or by the Earth symbol or coloured GREEN and YELL O W . • T[...]

19 E & O E. All instructions, dimensions and illustrations are provided for guidance only . CDA reserve the right to change specifications without prior notice. Attribute Symbol Units Model Identification edd61 edd91 Annual Energy Consumption AEC Hood 54.0 49.6 kWh Time increase factor f 1.0 0.9 Fluid Dynamic Efficiency FDE Hood 26.5 (B) 30.2 [...]

Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .care@cda.eu W : www. cda.eu www .cda.eu Please contact our Customer Care Department for Service on the details below Customer Care Department The Group L td. • Harby Road • Langar • Nottingh[...]