Casablanca Fan Company C8U47M AT1206 manuale d’uso

1 H ANOVER ™ Safet y and the proper operation of your Casablanca fan both requir e a thorough knowledge of the pr oduct and proper installation; therefore , before attempting to install and oper ate your Casablanca fan, read this owner’ s manual completely and carefully . Retain this manual for futur e reference . CAU T ION : T o avoid possible[...]

2 Circuit Br eak er (T rip break er for the circuit y ou will be working on) Fuse Box (Remo ve fuse for the circuit y ou will be working on) 18" ↑ 84" ↑ 70" ↑ •  e blades in each pack are matched for equal weight to assure smooth fan operation. If mor e than one fan is being installed, be careful not to mix blades f rom di[...]

3 H ANOVER ™ Before mounting your Casablanca fan, r ead the following helpful recommendations.  e loc ation of the fan, air circulation, and fan size are all important factors to consider before installation. L ocation Ceiling fans have practical uses in almost ever y room in your home. W e suggest you follow these mounting recommendations as [...]

4 CEILING HARD W ARE (not to scale) WA R N I N G ! Suppor t directly to building structure only . Using Existing Ceiling F ixture O utlet Box After turning the power OFF at its source (either circuit breaker or fuse box), lower the old fi xture and disconnect the wiring. Check the ceiling fi xture outlet box to be sure that it is marked “ Appro[...]

5 H ANOVER ™ NOTE:  is step is required only under two conditions: If the fan weighs 36 lbs. or more (which does not pertain to this fan) or if the existing ceiling fi xture outlet box needs to be modifi ed for a ceiling fan application (for example, if the house is not new construction and you are replacing an existing light fi xture). W e[...]

6 BLADE INST ALLA TION Blade Irons (4) Blades (4) Pack C: Blade Scre ws and W ashers (17) Pack D: Blade Iron Scr ews (9) BLADE HARD W ARE (not to scale) Attach Blade Irons Step 4. Using the screws in P ack C and the provided screwdriver , attach the blades to the blade holders b y aligning the screwholes of the blade iron with the holes in the blad[...]

7 H ANOVER ™ TIP:  e downr od has a tapered thread that is designed to lock completely when installed correctly . Step 6c. Using the provided Allen wrench (attached to the paper motor warning shield), remove the Allen set scr ew f rom the hanger adaptor and set it aside . Insert the downrod into the motor coupling and turn it cloc kwise until [...]

8 Step 9. Attach the fan wires to the ceiling fi xture outlet bo x wiring by placing the bare ends of the wires side b y side and then securing with a wire nut. T est that the co nnection is secure by pulling on the wir e nut. Connect in this order: • GRE E N leads f rom mounting plate and downrod assembly of fan to GROUND conductor of power sou[...]

9 H ANOVER ™ No Light Cap Adapter Plate Switch Housing Cap Finial Switch Housing Mounting Plate Scre ws Finial Glass Shade Switch Housing Mounting Plate Scre ws Socket Plate Lightbulbs OPTIONAL LIGHT KIT INST ALLA TION Step 11d. Install the third screw and securely tighten all three screws by hand only using the provided scr ewdriver . Note: If y[...]

10 Scre w 6-32 X 1" (2) Scre w 6-32 X 3 / 8 " (2) W ood Scre w 1" (2) Drywall Anchor 6-32 (2) 12v Battery W -73 Control W- 7 3 Control Holder VERSA•T OUCH2™ CONTROL INST ALLA TION CONTROL BRA CKET INST ALLA TION Standard Light S witch Step A. Remove the two screws holding the switch cover plate. Do not r emove the cover plate. St[...]

11 H ANOVER ™ Send Signal LED F an Control T o star t the fan. P ress the selected speed button to run the fan at the desired speed. LO W=Low speed MED=Medium speed HIGH=High speed T o turn off the fan, press the F AN OFF button. Airfl ow Direction T o reverse the airfl ow , press the REVE RSE button. RE VERSE operates at any speed whether the[...]

12 Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance. TROUBLESHOO TING TIPS PROBLEM POSSIBLE REMEDIES F an will not start • Check the main circuit fuses, cir cuit breakers, and wall switch position. Chec k all wire connections. Make sur e the power is turned off during this inspection. [...]

13 H ANOVER ™ F an F inishes • F or c leaning, a soft br ush or lint-f ree cloth should be used to prevent scratching the fi nish. • A vacuum cleaner br ush nozzle can remove heavier dust. • Surface smudges or an accumulation of dirt and dust can be removed easily by using a mild detergent and slightly dampened soft c loth. An antistatic a[...]

14 A UTHORIZED SER VICE CENTERS ALASKA Anchorage 99518 Bering Sea Eccotech 907-563-7988 ALABAMA Mobile 36618 Azalea City Service Ctr. 251-341-0663 Tuscaloosa 35405 Lighting Plus 205-345-8900 ARIZONA Green V alley 85614 Goble Electric 520-625-4938 Mesa 85204 Gallery of Fans 480-962-0477 Mesa 85210 Loud Inc. dba Fans Plus 480-827-9302 Phoenix 85032 B[...]

15 H ANOVER ™ IOW A Carroll 51401 J & L Electric Inc. 712-792-2444 ISO Cedar Rapids 52404 Acme Electric Company 319-365-8677 Coralville 52241 Ralston Creek 319-351-2189 ISO, WTS Davenport 52803 Shaw Electric 563-323-361 1 Des Moines 5031 1 Advanced Lighting 515-255-5009 WTS Monticello 52310 Rem Electric 319-465-3346 Sioux Center 51250 Hills H[...]

16 PRODUCT SPECIFICA TIONS Collection: Casablanca Designer Model Name: Hanover Model Number: C8U47M Dimensions: A = 11.45" B = 18" C = 3" D = 15" E = 5.6" W eight: 34 lbs. F inishes: Crackled W alnut/Spanish Gold Motor: 188 x 25mm Direct Drive TM Blade Span: 54" Blade Options: Any 21" badge-t ype blade Blade Iron [...]