Watlow Electric 733 manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40

Aller à la page of

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Watlow Electric 733. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Watlow Electric 733 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Watlow Electric 733 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Watlow Electric 733 devrait contenir:
- informations sur les caractéristiques techniques du dispositif Watlow Electric 733
- nom du fabricant et année de fabrication Watlow Electric 733
- instructions d'utilisation, de réglage et d’entretien de l'équipement Watlow Electric 733
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Watlow Electric 733 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Watlow Electric 733 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Watlow Electric en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Watlow Electric 733, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Watlow Electric 733, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Watlow Electric 733. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    0600-0008-0000 Rev D November 1995 Supersedes without change: W733-XSMN Rev D00 $10.00 Made in the U.S.A. T ime/T emperature Control Total Customer Satisfaction 3 Year Warranty Series 733/734 Watlow Controls, 1241 Bundy Blvd., P.O. BOX 5580, Winona, MN 55987-5580, Phone: 507/454-5300, Fax: 507/452-4507 Service Manual[...]

  • Page 2

    2 WATLOW Series 733/734 Service Manual Install & Wire, Chapter 1 This manual is a supplement to the Series 733/734 Program Manual. It is for configuring, servicing and calibrating your control. Use this manual in conjunc- tion with the Series 733/734 Program Manual and Data Communications manual. Contents T echnical Assistance If you encounter [...]

  • Page 3

    3 WATLOW Series 733/734 Service Manual Install & Wire, Chapter 1 Install Chapter 1 Install and Wire the Series 733/734 Front panel mounting for ease of installation and service. Series 734 Figure 1 - Series 733 and 734 Dimensions. ˜ NOTE: For Series 734 orientation (verti- cal), rotate the panel cutout 90°. Figure 2 - Panel Cutout. 1.975 (50 [...]

  • Page 4

    4 WATLOW Series 733/734 Service Manual Install & Wire, Chapter 1 Wiring Figure 6 - Series 733/734 Rear View. 9-pin Event Input/ Output Connector 12-pin Output Wiring Connector Input/ Communications Connector How to Wire the Series 733/734 The Series 733/734 wiring is illustrated by model number option. Check the terminal designation sticker on [...]

  • Page 5

    5 WATLOW Series 733/734 Service Manual Install & Wire, Chapter 1 Wiring Figure 8 - Input Wiring Con- nector. Figure 7 - 24V Å Å Å Å Å (VAC) Power Wiring. ∫ WARNING: To avoid potential electric shock, use National Electric Code (NEC) safety practices when wiring and connect- ing this unit to a power source and to electrical sensors or per[...]

  • Page 6

    6 WATLOW Series 733/734 Service Manual Install & Wire, Chapter 1 Input Wiring Figure 10 - 2 or 3 Wire RTD Wiring. Figure 9 - Thermocouple Wiring. ˜ NOTE: Dual-zone thermo- couple units require at least one un- grounded thermocouple. 1 2 3 + - 4 5 6 + - Thermocouple Input 73XX- 1 XXX-XXXX ˜ (Dual Zone Only) 73XX- 4 XXX-XXXX 73XX- 6 XXX-XXXX 73[...]

  • Page 7

    7 WATLOW Series 733/734 Service Manual Install & Wire, Chapter 1 Input Wiring Figure 11 - 0-5VDC or 0-10VDC Process Input Wiring. Figure 12 - 0-20mA or 4-20mA Process Input Wiring. 4 5 6 + - DC I 4 5 6 + - Zone 2 Zone 2 0-5VDC or 0-10VDC Process Input Model # 73XX- 6 XXX-XXXX (Dual Zone Only) 0-20mA or 4-20mA Process Input Model # 73XX- 6 XXX-X[...]

  • Page 8

    8 WATLOW Series 733/734 Service Manual Install & Wire, Chapter 1 Output 1 Wiring Figure 14 - DC Output 1 Wiring. Figure 13 - AC Output 1 Wiring. 1 2 3 4 5 6 7 8 9 10 11 12 - External Load + - + 1 2 3 4 5 6 7 8 9 10 11 12 External Load COM L1 L2 Fuse AC Output Wiring - Zone 1 Solid State Relay with Mechanical Relay with Contact Suppression Conta[...]

  • Page 9

    9 WATLOW Series 733/734 Service Manual Install & Wire, Chapter 1 Output 2 Wiring Figure 16 - DC Output 2 Wiring. Figure 15 - AC Output 2 Wiring. 1 2 3 4 5 6 7 8 9 10 11 12 External Load + - - + 1 2 3 4 5 6 7 8 9 10 11 12 External Load COM L1 L2 Fuse NO AC Output Wiring - Zone 2 Solid State Relay with Mechanical Relay with Contact Suppression Co[...]

  • Page 10

    10 WATLOW Series 733/734 Service Manual Install & Wire, Chapter 1 Optional Wiring Figure 18 - Event Output Wiring. Figure 19 - Alarm Wiring. ˜ NOTE: Event Input is not available on stan- dard Series 733/734 controls. Consult factory for more information. Figure 17 - Event Input Wiring. 1 2 3 4 5 6 7 8 9 Event Input 2 Common Event Input 1 1 2 3[...]

  • Page 11

    11 WATLOW Series 733/734 Service Manual Install & Wire, Chapter 1 Figure 20 - System Wiring Example. Figure 21 - Series 733/734 Ladder Diagram Example. System Example L1 L2 SSR-240-10G-DC1 TC (+) (-) 2 3 Process Sensor Limit Sensor Coil Normally Open Momentary Switch 142A-36XX-1200 UL recognized safety limit control (+) (-) Reset L2 (+) (-) Hig[...]

  • Page 12

    12 WATLOW Series 733/734 Service Manual Setup Mode, Chapter 2 Setup = Parameter may not appear depending on control configuration = Only appears if your unit has communications. See the Series 733/734 data communications manual for more information. SERIES 733 TL W W A 81 0 1 2 1 3 5 2 4 6 7 9 11 EVENT LOAD 1 READY MENUS Celsius_Fahrenhei t Guard b[...]

  • Page 13

    13 Setup Mode, Chapter 2 WATLOW Series 733/734 Service Manual Setup Figure 23 - WatCurve™ Example. F ˜ NOTE: Countdown time will speed up or slow down depending on WatCurve™ algo- rithm . Display alternates between parameter and programmed data. C_F gb 4000 rtd din tcnP OFF Temperature 325°F/ °C Time WatCurve™ Time 3 Minutes 163°C tS nnSc[...]

  • Page 14

    14 WATLOW Series 733/734 Service Manual Setup Mode, Chapter 2 Setup Display alternates between parameter and programmed data. LAt nL InP1 J rL1 32 rH1 1382 AL1 Pr A1LO 32 A1HI 1382 HYS1 3 CAL1 0 InP2 J Alarm Latching: Selects whether the alarm output is latching or non-latching. This parameter only appears if your unit has alarms, and AL1 no and AL[...]

  • Page 15

    15 Setup Mode, Chapter 2 WATLOW Series 733/734 Service Manual Setup Table 1 - Input Ranges. Display alternates between parameter and programmed data. Input Type Sensor Range Low Sensor Range High J 32°F/0°C 1382°F/750°C K (appears as H) 32°F/0°C 2282°F/1250°C E 32°F/0°C 1220°F/660°C rtd (1°) 32°F/0°C 1112°F/600°C 0-5 or 010 (VDC) -[...]

  • Page 16

    16 WATLOW Series 733/734 Service Manual Setup Mode, Chapter 2 Parameter Value Range Factory Default Appears If: C_F C or F F gb 1 to 4000°F/2222°C 4000°F/2222°C rtd JIS or din din Input type is RTD tncP On or OFF OFF tS hrnn or nnSc nnSc SIL On or OFF OFF Unit has alarms, AL1 no & AL2 no LAt LA or nL nL Unit has alarms, AL1 no & AL2 no [...]

  • Page 17

    17 Service Mode, Chapter 3 WATLOW Series 733/734 Service Manual Service Figure 23 - Service Mode Key Flow. Chapter 3 The Service Mode Enter the Service mode by pressing the key sequence illustrated below. The display shows the [AUt1] parameter. Move through the Service mode by pressing the TIME key . Use the UP/DOWN keys to select data. After 1 min[...]

  • Page 18

    18 WATLOW Series 733/734 Service Manual Service Mode, Chapter 3 Service Display alternates between parameter and programmed data. 0 AUt1 AUt2 0 Pb1 25 rE1 0.00 rA1 0.00 Ct1 5 Pb2 25 rE2 0.00 0.00 rA2 Service Parameters Auto-tune Zone 1: Initiates auto-tune for Zone 1. For more information on tuning, see Chapter 4, Page 19. Range: 0 = off, 1 = slow,[...]

  • Page 19

    19 Service Mode, Chapter 3 WATLOW Series 733/734 Service Manual Parameter Value Range Factory Default Appears If: AUt1 0 - 3 0 AUt2 0 - 3 0 Hardware is present Pb1 0 to 999°F/0to 555·C 25°F rE1 0.00 to 9.99 repeats/minute 0.00 Pb1 0 rA1 0.00 to 9.99 minutes 0.00 Pb1 0 Ct1 1 to 60 seconds 5 Pb1 0 Pb2 0 to 999°F/0 to 555°C/0 to 999 Units 25°F H[...]

  • Page 20

    20 WATLOW Series 733/734 Service Manual Tuning, Chapter 4 T uning Figure 24 - Auto-tuning at a Set Point of 200°F. ˜ NOTE: An X applies to either Zone 1 or Zone 2. ˜ NOTE: In dual zone applica- tions, allow Zone 1 to complete before tuning Zone 2. Chapter 4 T uning Auto-tuning Auto-tuning applies to Zone 1 or 2. The auto-tuning procedure operate[...]

  • Page 21

    Tuning, Chapter 4 WATLOW Series 733/734 Service Manual 21 T uning ˜ NOTE: Tune each zone at a set point above ambient tempera- ture. 2. Select a thermal response value using the UP/DOWN keys, 1=slow, 2=me- dium, and 3=fast. A thermal response value of 2 satisfactorily tunes most thermal systems. 3. When tuning is complete, the display returns to i[...]

  • Page 22

    22 WATLOW Series 733/734 Service Manual Calibration, Chapter 5 Chapter 5 The Calibration Mode Before attempting to calibrate, make sure you have the proper equipment called for in each procedure. Use the key sequence below to enter the Calibration Mode. In the Calibration Mode, various input signals must be supplied in order for the control to go t[...]

  • Page 23

    Calibration, Chapter 5 23 WATLOW Series 733/734 Service Manual Calibration ç Before attempting to calibrate, make sure you have the proper equipment called for in each procedure. The Series 733/734 is calibrated and tested before leaving the factory. CALy InLO InHI nAHI tC Ot1L Ot1H Ot2L Ot2H Calibration Parameters Calibrate: Determines which para[...]

  • Page 24

    24 WATLOW Series 733/734 Service Manual Calibration, Chapter 5 rSt LgOt Calibration LI HEy dISP Restoring Factory Calibration The rSt parameter restores the factory calibration values to the Series 733/734. If you calibrate your control incorrectly, you have the option to default to the original values. Once you leave the CAL menu, the values are e[...]

  • Page 25

    Calibration, Chapter 5 25 WATLOW Series 733/734 Service Manual T/C Calibration Calibration ˜ NOTE: Before calibration on an installed control, make sure all data and param- eters are docu- mented. See Setup, and Service Tables, Pages16 and 19. ˜ NOTE: Always press the Time key to advance to the next param- eter before chang- ing the calibration e[...]

  • Page 26

    26 WATLOW Series 733/734 Service Manual Calibration, Chapter 5 R TD Calibration ˜ ˜ NOTE: Before calibration on an installed control, make sure all data and param- eters are docu- mented. See Setup, and Service Tables, Pages16 and 19. ˜ NOTE: Always press the Time key to advance to the next param- eter before chang- ing the calibration equipment[...]

  • Page 27

    Calibration, Chapter 5 27 WATLOW Series 733/734 Service Manual T/C-Process Input ˜ NOTE: Before calibration on an installed control, make sure all data and param- eters are documented. See Setup and Service Tables, Pages 16 and 19. ˜ NOTE: Always press the Time key to advance to the next param- eter before chang- ing the calibration equipment. ˜[...]

  • Page 28

    28 WATLOW Series 733/734 Service Manual Calibration, Chapter 5 4-20mA Output ˜ NOTE: Before calibration on an installed control, make sure all data and para- meters are docu- mented. See Setup and Service Tables, Pages 16 and 19. The calibration procedure for Zone 1 and Zone 2 are the same except use the Ot2L and Ot2H parameters for Zone 2. Zone 1[...]

  • Page 29

    Calibration, Chapter 5 29 WATLOW Series 733/734 Service Manual 0-5V Output ˜ NOTE: Before calibration on an installed control, make sure all data and para- meters are docu- mented. See Setup and Service Tables, Pages 16 and 19. The calibration procedure for Zone 1 and Zone 2 are the same except use the Ot2L and Ot2H parameters for Zone 2. Zone 1 0[...]

  • Page 30

    Appendix 30 WATLOW Series 733/734 Service Manual Glossary , A - I Alarm: A condition, generated by a controller, indicating that the process has exceeded or dropped below a predetermined alarm set point. Alarm Silence: Disables the alarm relay output. Anti-reset: Control feature that inhibits automatic reset action outside the proportional band. Al[...]

  • Page 31

    Appendix 31 WATLOW Series 733/734 Service Manual Glossary , I - Z Integral: Control action that automatically eliminates offset, or “droop,” between set point and actual process temperature. Also "reset." I solation: Electrical separation of sensor or other device from high voltage circuitry. Allows for applica- tion of grounded or un[...]

  • Page 32

    Appendix 32 WATLOW Series 733/734 Service Manual A Advancing Through Setup, 12 Alarm, Parameters, 14 - 16 Wiring, 10 Appendix, 30 Auto-tuning, 20 C Calibration,22 - 29 Changing Setup Data, 12 D DC Output 1 Wiring, 8 DC Output 2 Wiring, 9 Default Parameters, Service, 19, Table 3 Setup, 16, Table 2 Dimensions, 3 E Event Input Wiring, 10 Event Output [...]

  • Page 33

    Appendix 33 WATLOW Series 733/734 Service Manual Warranty The Watlow Series 733/734 is warranted to be free of defects in material and workmanship for 36 months after delivery to the first purchaser for use, providing that the units have not been misapplied. This excludes mechanical relays which are war- ranted for 100,000 cycles. Since Watlow has [...]

  • Page 34

    Appendix 34 WATLOW Series 733/734 Service Manual Specific Specifications Control Mode • Single or dual input, single or dual output, single alarm. • EIA/TIA-422A, EIA/TIA-423A, or EIA/TIA-485 data communications. • ON/OFF: Determined by the HYS X parameter for Outputs 1 and 2. • PID Parameters: • Proportional band: 0 to 999°F/0 to 555°C[...]

  • Page 35

    Appendix 35 WATLOW Series 733/734 Service Manual Model Number 733/734 = One or two channel microprocessor-based, time and temperature control; 24V Å (VAC) power input. *Order power supply and connector kit(s) separately below. Display Orientation 3 = Horizontal 4 = Vertical Display Location A = Integral (local) Input Type 1 = Single thermocouple ([...]

  • Page 36

    Declaration of Conformity WATLOW CONTROLS 124 1 Bundy Boulevard Winona, Minnesota 55987 USA Declares that the following product: Designation: Model Number: Classification: Series 733 I734 733A-4BB l-AAAG Electronic Incorporated Class III temperature controller, Type 2C action, for use in light industrial environment Rated Voltage: 24V- (VAC) Rated [...]

  • Page 37

    Appendix 37 WATLOW Series 733/734 Service Manual Notes[...]

  • Page 38

    Appendix 38 WATLOW Series 733/734 Service Manual Notes[...]

  • Page 39

    Appendix 39 WATLOW Series 733/734 Service Manual[...]

  • Page 40

    Appendix 40 WATLOW Series 733/734 Service Manual Watlow Series 733/734 Service Manual Watlow Controls, 1241 Bundy Blvd., P.O. Box 5580, Winona, MN 55987-5580, 507/454-5300, Fax: 507/452-4507[...]