Pelco C3425M-D manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

Aller à la page of

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Pelco C3425M-D. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Pelco C3425M-D ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Pelco C3425M-D décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Pelco C3425M-D devrait contenir:
- informations sur les caractéristiques techniques du dispositif Pelco C3425M-D
- nom du fabricant et année de fabrication Pelco C3425M-D
- instructions d'utilisation, de réglage et d’entretien de l'équipement Pelco C3425M-D
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Pelco C3425M-D ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Pelco C3425M-D et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Pelco en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Pelco C3425M-D, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Pelco C3425M-D, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Pelco C3425M-D. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    INST ALLA TION C3425M-D (8/08) IS90 Series Camclosure ® Indoor Integrated Camera System[...]

  • Page 2

    2 C3425M-D (8/08) Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 [...]

  • Page 3

    C3425M-D (8/08) 3 List of Illustrations 1 Package Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 Removing the Bubble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3 Ceiling/W all[...]

  • Page 4

    4 C3425M-D (8/08) Regulatory Notices This device complies with Part 15 of the FCC Rules. O peration is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE Th[...]

  • Page 5

    C3425M-D (8/08) 5 Description The IS90 Series Camclosure ® integrated camera system combines a camera and lens package in a small, discreet dome. The system is easy to install and can be mounted to the surface of a ceiling/wall or recessed in a ceiling/wall. The unit supports both BNC and unshielded twisted pair (UTP) video wiring. Before installi[...]

  • Page 6

    6 C3425M-D (8/08) Indoor dome, surface/flush mount, smoked and clear bubble, black finish PARTS LIST Camera T ype Lens/Iris NTSC P AL Color , Wide Dynamic Range, Day/Night 3-9.5 mm, Day/Night V arifocal, Auto Iris IS90B-DWV9 9-22 mm, Day/Night V arifocal, Auto Iris IS90B-DWV22 Color , High Resolution, Day/ Night 3-9.5 mm, Day/Night V arifocal, Auto[...]

  • Page 7

    C3425M-D (8/08) 7 Figure 1. Package Comp onents IS90 SERIES CAMCLOSURE WITH SMOKED BUBBLE LINER ADAPTER PLA TE CLEAR BUBBLE SHOWN ACTUAL SIZE SHIPPING BOX 8-32 X 1.00-INCH PHILLIPS P AN HEAD SCREWS (2) 8-32 X 0.75-INCH PHILLIPS P AN HEAD SELF-T APPING SCREWS (2) 8-32 X 2.50-INCH PHILLIPS P AN HEAD SELF-T APPING SCREWS (2) 10-32 X 1.50-INCH PHILLIPS[...]

  • Page 8

    8 C3425M-D (8/08) Remove the Bubble T urn the bubble counterclockwise and lift (refer to Figure 2). Place th e bubble on a nonabrasive surface. If the liner is already installed, remo ve it b efore installing the unit. T o remove the liner , gently lift it from the unit. Place the liner to th e side; it will be reinstalled later with the bubble (re[...]

  • Page 9

    C3425M-D (8/08) 9 Installation Y ou can install the IS90 Series Camclosure integrated camera system into any of the following: • Mount to the surface of a ceiling/wall (refer to Surface Installation: Ceiling/Wall on pa ge 9). • Install in a suspended ceiling (refer to In-Ceiling Installation: Suspended Ceiling o n page 11). • Install in a fix[...]

  • Page 10

    10 C3425M-D (8/08) Figure 3. Ceiling/Wall Installation Figure 4. Concrete Ceilin g/Wall Installation BACK BOX AND SURFACE MOUNT RING WAL L OR CEILING 6-32 TOGGLE BOL TS (NOT SUPPLIED) BACK BOX AND SURF ACE MOUNT RING 8-32 MOUNTING HARDW ARE (NOT SUPPLIED) CONCRETE W ALL OR CEILING[...]

  • Page 11

    C3425M-D (8/08) 11 IN-CEILING INSTALLATION: SUSPENDED CEILING 1. Remove the surfa ce mount ring from the back box (re fer to Figure 5): a. Place fingers on the circular marks located on the sides of the surface mount ring . b. Pinch the sides. c. Lift and remove the surface mount ring from the back box. Do not discard the surface mount ring; it is [...]

  • Page 12

    12 C3425M-D (8/08) 2. Pull video and power wires to the selected ceiling tile. 3. Mount the unit to the ceiling tile (refer to Figure 6 and Figure 7): a. Remove the ceiling tile from the ceiling. b. Cut a hole 4 inches (10 cm) in diameter in the ceiling tile. c. Use one of the following: • T o mount with the adapte r plate, place the adapter plat[...]

  • Page 13

    C3425M-D (8/08) 13 4. Remove an adjacent ceiling tile to access the unit. 5. Connect the video cable/wires: • BNC: Connect the BNC connector from the unit to a mating BNC connector . • UTP: Blue wire = Video + Gray wire = Video - 6. Connect the power wires. AC operation only: If you are wiring more than one Camclosure to the same transformer , [...]

  • Page 14

    14 C3425M-D (8/08) 6. Attach the back box to the mounting surface: • If you have access behind the ceiling/wall (refer to Figure 6 on page 12): (1) Place the adapter plate on t he inside of the ceiling/wall. (2) Attach the back box to the ceiling/wall. Us e the two sup plied 10-32 x 1.50-inch Phillips pan head self-tapping screws. • If you do n[...]

  • Page 15

    C3425M-D (8/08) 15 5. Attach the surface mount ring and b ack box to th e adapter plate with two supplied 8-32 x 2.50-inch Phillips pan head self-tapping screws. Figure 9. 4S Standard Electrical Bo x Instal lati on IN-CEILING INSTALLATION: 4S DEEP ELECTRICAL BOX 1. Remove the surfa ce mount ring from the back box (re fer to Figure 5 on page 11): a.[...]

  • Page 16

    16 C3425M-D (8/08) 5. Connect the power wires. AC operation only: If you are wiring more than one Camclosure to the same transforme r , connect one side of the transformer to the red wire on all uni ts; connect the other side of the transformer to the black wire on all units. NOTE: Failure to connect all AC po wered units the sa me way will cause t[...]

  • Page 17

    C3425M-D (8/08) 17 Camera Adjustments T o perform the following camera adjustments, connect a monitor . Then turn on power to the camera and monitor . T o use the service connector , refer to Service Connector on page 28. T o set the DIP switches or to adjust the auto iris level (DN, CH, or C) or the vertical phase (DW or CW), you will need a minia[...]

  • Page 18

    18 C3425M-D (8/08) DN/CH/C SERIES ADJUSTMENTS Refer to Figure 12 to adjust the IS90-DN, IS90-CH, or IS90-C model. Figure 12. Adjusting the IS90-DN/C H/C Series Camclosure SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation. SW4-1: AGC (Auto Gain Control) The AGC (automatic gain contr ol) ad justs the image a utomatica[...]

  • Page 19

    C3425M-D (8/08) 19 SW4-4: Flickerless In certain lighting conditions, a flicker in the light source may affect camera operation. Flic kering can be caused by a number of conditions, including the qua lity of the source power and the age and type of fluorescent bulbs and ballasts. Set to ON to enable flickerless operation. The camera wi ll remove th[...]

  • Page 20

    20 C3425M-D (8/08) V ERTICAL PHASE ADJUSTMENT NOTE: Use this procedure for 24 V AC operation only . When using more than one camera power supply, a brief vertical roll may occur on the monitor when switching from one came ra to another . T o eliminate vert ical roll, reverse the 24 V AC connec tions on one camera. If both cameras a re connected to [...]

  • Page 21

    C3425M-D (8/08) 21 DAY/NIGHT OPERATION NOTE: This section only applies to DN model cameras. DN model cameras regularly check the brightness level of the field of view t o determine when to switch between day (color) and nig ht (black-white) operation. Actual brightness threshold levels are affected by camera angle, amount of zoom, field of view , l[...]

  • Page 22

    22 C3425M-D (8/08) DW/CW SERIES (WIDE DYNAMIC RANGE) ADJUSTMENTS Refer to Figure 14 to adjust the IS90-DW or IS90-CW model. Figure 14. Adjusting the IS90-DW/ CW Series Camclosure SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation. SW1-1: Video Format Set to ON for NT SC. Set to OFF for PAL. The default is ON. SW1-2: [...]

  • Page 23

    C3425M-D (8/08) 23 SW1-4: A WB (Auto White Balan ce)/MWB (Manual White Balance ) Auto white balance is enabled by default (O N). T o manually set and lock the white balance: 1. Set SW1-4 to ON. 2. Hold a white background in front of the lens until the video shows all white. 3. While holding the background in place, set SW1-4 to OFF . A green block [...]

  • Page 24

    24 C3425M-D (8/08) SW1-8: Day/Night Operation (DW models only) NOTE: On CW models, SW1-8 is unused and does not affect camera operation . DW model cameras regularly check the brightness level of the field of view to determine when to switch between day (color) and nig ht (black-white) operation. Use SW1-8 to set the ge neral light levels at which t[...]

  • Page 25

    C3425M-D (8/08) 25 AUTO IRIS LEVEL ADJUSTMENT The electronics of the IS90-DW and IS90-CW Series Ca mclosures automatically adjust the camera to the auto iris. Auto iris level adjustments are not necessary . V ERTICAL PHASE ADJUSTMENT NOTE: Use this procedure for 24 V AC operation only . When using more than one camera power supply, a brief vertical[...]

  • Page 26

    26 C3425M-D (8/08) Camera Positioning Rotate and tilt the camera module to position the camera. NOTE: Do not over -rotate the module. Excessively turni ng the module in one direction could result in damage to the wiring. Figure 16. Positioning the Camera ì T ilt 140° (20°–160°) î Pan 360° ï Rotation 360°   [...]

  • Page 27

    C3425M-D (8/08) 27 Install Liner and Bubble 1. T o install the liner with a clear bubble (refer to Figure 17): a. Align the studs located on the camera module with the clips on the liner . b. Lightly pinch the sides of the liner , o pposite fro m the clips, and place the clips over the studs. c. When the liner is secure, position the viewing window[...]

  • Page 28

    28 C3425M-D (8/08) Service Connector The IS90 Series Camclosure integrated camera system includes a service connector that outputs camera video. Use it at the installation site to set up the field of view and focus the camera. Figure 1 9. Service Connector Pelco offers two optional items that plug directly in to the service connector . Before using[...]

  • Page 29

    C3425M-D (8/08) 29 T o assemble the cable: 1. Attach the CPM 88 miniature coaxial connector to one end of the cable. Follow the directio ns supplied with the mini ature coaxial connector . 2. Attach the 2.5 mm monaural plug to the other end of the coaxial cable (refer to Figure 20): a. Remove the support sleeve from the plug. b. Slip the support sl[...]

  • Page 30

    30 C3425M-D (8/08) Specifications GENERAL Pan/T ilt Adjustment Manual Pan 360° T ilt 140° (20° to 160° range) Rotation 360° Construction Back Box and Surface Mount Ring ABS plastic Bubble Polycarbonate Finish White or black Environment Indoor Operating T emperature 32° to 120°F (0° to 49°C) Unit Weight 0.52 lb (0.24 kg) ELECTRICAL Input V [...]

  • Page 31

    PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, an y merc handise proved defective in materi al or workmanship for a period of one year after the date o f shipment. Exception s to this warrant y are as noted bel ow: • Five years on fiber opt ic products and TW3000 Serie s unshielded twisted pair (UTP[...]

  • Page 32

    Worl dwide He adquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 Australia | Finland | France | Germany | Italy | Macau | The Nethe rlands | Russia | Singapore South Africa | Spain | Sweden | United Arab Emirates[...]