Olitec RW400G manuel d'utilisation

R R W W 4 4 0 0 0 0 G G R R o o u u t t e e r r O O L L I I T T E E C C User's Guide[...]

[...]

Chapter 2: In troducti on...................................................................................................... 1 2.1 Overview of the R outer ........................................................................................ 1 2.2 Feat ures .......................................................................................[...]

5.10.2 Oray .net DDNS ...................................................................................... 42 5.10.3 Comexe .cn DDNS .................................................................................. 43 5.1 1 System T ools .................................................................................................... 44 5.1 1[...]

Chapter 2: Introduction 2.1 Overview of the Router The RW400 G Wireless Router integrate s 4 -p o rt S wi t c h, firewall, NA T -router and Wireless AP . Its design is dedicated to Sma ll Office/Hom e Office (SOHO) wir eless network solutions. The R W400G Wireless Router will allow you to connect your network wire lessly better than ever , sharing [...]

restricted access policies based on the time of day for children or staff ¾ Supports TCP/IP , PPPoE, DHCP , ICMP , NA T , SNTP ¾ Supports UPnP , Dynamic DNS, S tatic Routing, VPN p ass-through ¾ Supports T raffic S tatistics ¾ Supports ICMP-FLOOD, UDP-FLOOD, TCP-SYN-FLOOD filter ¾ Ignores Ping packet s from W AN or LAN ports ¾ Supports firmwa[...]

hold the default reset button then turn on the rout er's power , until the system LED lights up (about 3 seconds). Last, release the reset button and wait for the router to reboot. Note : Ensure the router is powered on before it restar ts completely . ¾ W AN RJ45 port for connecting the router to a cable, DSL modem, or Ethernet ¾ Four LAN 1[...]

Chapter 3: Connecting the Router 3.1 System Requirement s ¾ Broadband Internet Access Service (DSL/Cable/Ethernet) ¾ One DSL/Cable modem that has an RJ45 conn ector (y ou do not need it if you connect the router to Ethernet) ¾ Each PC on the LAN needs a working Ether net Adapter and an Ethernet cable with RJ45 connectors ¾ TCP/IP protocol must [...]

To L A N Switch/Hub 4 3 2 1 WAN To WA N RESE T （） XDSL C abl e Et he rne t 、、 Figure 3-1: Hardware Installation of the R W400G Wireless Router - 5 -[...]

Chapter 4: Quick In st allation Guide After connecting the R W400G Router into your network, you should configure it. This chapter describes how to conf igure the basic functions of your RW400G Wireless Router . These procedures only take you a few minut es. Y ou can access the Internet via the router immediately after successfully configured. 4.1 [...]

If the result displayed is sim ilar to that shown in figure 4-1, the connection between your PC and the router has been established. Figure 4-2: Failed result of Ping command If the result displayed is similar to that shown in figure 4-2, it means that your PC has not connected to the router . Please c heck it following these steps: 1. Is the conne[...]

Figure 4-4 Login Windows Note : If the above screen does not prompt, it means that your web-browser has been set to a proxy . G o to T ools menu>Inter net Op tions>Connections>LAN Settings, in the screen that appears, cancel the Using Proxy c heckbox, and click OK to finish it. If the User Name and Password are correct, y ou can configure [...]

Figure 4-7 Quick Setup - PPPoE ¾ User Name and Password - Enter the User Nam e and Password provided by your ISP. These fields are case s ensitive. If you have difficult y with this process, please contact your ISP. If you choose " Dyn a mi c I P ", the router will automatically receive the IP parameters from your ISP without needing to [...]

In this page, you can configure the following wireless parameters: ¾ Wireless Radio - indicates whether the Access Po int feature of the router is enabled or disabled. If disabled, the WLAN LED on the front panel will not be lit and the wireless stations will not be able to access the router . If enabled, the WLA N LED will be lit up and wireless [...]

Chapter 5: Configuring the Router This chapter describes eac h web page's key functions. 5.1 login After your successful login, you can confi gure and manage the router . There are ten main menus on the left of the web- based utility . Submenus will be av ailable after you click one of the main menus. The ten main me nus are: St atus, Quick Se[...]

Figure 5-1: Router S tatus 5.3 Quick Setup Please refer to Section 4.2: "Quick Installation Guide." 5.4 Network Figure 5-2: the Network menu There are three submenus under the Network menu (shown in figure 5-2): LAN , WA N and MAC Clone. Click any of them, and you will be abl e to configure the corresponding function. The detailed explana[...]

5.4.1 LAN Y ou can configure the IP p arame ters of LAN on this page. Figure 5-3: LAN ¾ MAC Address - the physical address of the rout er , as seen from the LAN. The value can't be changed. ¾ IP Address - Enter the IP address of y our router in dotted-decimal notation (factory default: 192.168.1.1). ¾ Subnet Mask - An address code that dete[...]

Figure 5-4 WAN – Dynamic IP This page displays the W AN IP paramete rs assigned dynamically by your ISP , including IP address, Su bnet Mask, Default Gateway , etc. Click the Renew button to renew the IP p arameters from your ISP . Click the Release button to release the IP parameters. MTU Size: The normal MTU (Maximum T ransmission Unit) value f[...]

Figure 5-4a: W AN - 802.1X + Dynamic IP ¾ User Name - Enter the user name for 802.1x authentication provided by your ISP ¾ Password - Enter the password for 802.1x authentication provided by your I SP. Click Login button to star t 802. 1x authentication. Click Logout button to end 802.1x authentication. 2. If you choose Static IP, you should have[...]

If you are also given a user name and a password for 802.1x authentication, you should select 802.1x + St atic IP for W AN Connection T ype , a box will then appear requesting a user name and a password, shown in figure 5-5a: Figure 5-5a: W AN - 802.1X + S tatic IP ¾ User Name - Enter the user name for 802.1x authentication provided by your ISP ¾[...]

Caution : Sometimes the connection cannot be disconnected although you specify a time to Max Idle T ime, since some applicati ons is visiting the Internet continually in the background. ¾ Connect Automatically - Connect automatically after t he router is disconnected. T o use this option, clic k the radio button. ¾ Time-based Connecting - Y ou ca[...]

it is necessary for your ISP . ¾ Service Name/AC Name - The service name and AC (A ccess Concentrator) name, this should not be done unless you are sure it is necessary for your ISP . ¾ ISP S pecified IP Address - If you know that your IS P does not automatically transmit your IP address to the router during login, click “ Use the IP A ddress s[...]

5.5 Wireless Figure 5-9: Wireless menu There are three submenus under the Wireless menu (shown in figure 5-9): Wireless Settings , MAC Filtering and Wireless S t atistics. Click any of them, and you will be able to configure the corresponding functi on. The detailed explanation s for each submenu are provided below . 5.5.1 Wireless Settings The bas[...]

wireless function of the router in a region other th an one of thos e specified in this field. If your country or region is not li sted, please contact yo u r local government agency for assistance ¾ Channel - This field determines which operati ng frequency will be used. It is not necessary to change the wireless channel unless you notice interfe[...]

Hexadecimal format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in a specified length. ¾ WEP Key settings - Select which of the four keys will be used and enter the matching WEP key information for your ne twork in the selected key radio button. These values must be identical on all wireless stations in your network. ¾ Key Typ[...]

5.5.2 MAC Filtering The Wireless MAC Filtering for wireless net works are set on this page, figure 5-1 1: Figure 5-1 1: Wireless MAC addr ess Filtering The Wireless MAC Address Filtering feature al lows you to control wireless stations accessing the router, which depend on the station's MAC addresses. ¾ MAC Address - The wireless st ation&apo[...]

Figure 5-12: Add or Modify Wire less MAC Address Filtering entry To add or modify a MAC Address Filter ing entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). For example: 00-0A-EB-B0-00-0B. 2. Enter a simple description o[...]

1. Click the Enable button to enable this function. 2. Select the radio button: Deny the stations not specified by any enabled entries in the list to access for Filtering Rules. 3. Delete all or disable all entries if there exist any entries already. 4. Click the Add New... button and enter the MAC address 00-0A-EB-00-07-BE in the MAC Address field[...]

Figure 5-13: The router attached wireless st ations ¾ MAC Address - The connected wireless station's MAC address ¾ Current Status - The connected wireless station's running status, one of STA-AUTH / STA-ASSOC / AP-UP / W PA / WPA-PSK /WPA2/WPA2-PSK/None ¾ Received Packets - packets received by the station ¾ Sent Packets - packets sent[...]

¾ DHCP Server - Enable or Disable the DHCP server . If you disable the Server , you must have another DHCP server within your network or else you must manually configure the computer . ¾ St art IP Address - This field specifies the first of the ad dresses in the IP address pool. 192.168.1.100 is the default start address. ¾ End IP Address - This[...]

5.6.3 Address Reservation When you specify a reserved IP address for a PC on the LAN, that PC will always receive the same IP address each time w hen it accesses the DHCP server. Reserved IP addresses should be assigned to servers t hat require permanent IP settings. This page is used for address reservation (shown in figure 5-17). Figure 5-17: Add[...]

Note : The function won't t ake effect until the router reboots. 5.7 Forwarding Figure 5-18: the Forwarding menu There are four submenus under the Fo rwarding menu (shown in figure 5-18): Vi rt u al Servers , Port T riggering , DMZ and UPnP . Click any of them, and you will be able to configure the corresponding function. The detailed explanat[...]

protocols supported by the router). ¾ Enable - Th e Enable checkbox to enable the virtual server entry . ¾ Common Service Port - Some common services already list in the pull-down list. To setup a virtual server entry: 1. Select the service you want to use fr om the Common Service Port list, and select the ID you want to use, and click Copy to bu[...]

Figure 5-20: Port Triggering Once configured, operation is as follows: 1. A local host makes an outgoing connec tion using a destination port number defined in the T rigger Port field. 2. The router records this connection, opens the incoming port or ports associated with this entry in the Port T riggering table, and associates them with the local [...]

4. Select the protocol used for Incoming Port s Range from the pull-down list, either TCP or UDP , or All. 5. Select the Enabl e checkbox to enable. 6. Click the Save button to save the new rule. There are many popular applications in the Popular Application list. You can select it and the ID, then click the Copy to button, the applicat ion will fi[...]

T o assign a computer or server to be a DMZ server: 1. Click the Enable radio button 2. Enter the local host IP Address in the DMZ Host IP Address field 3. Click the Save button. Note : After you set the DMZ host, the fire wall related to the host will not work. 5.7.4 UPnP The Universal Plug and Play (UPnP) feature allows the devices, such as Inter[...]

5.8 Security Figure 5-23: the Security menu There are six submenus under the Secu rity menu (shown in figure 5-23): Firewall , IP Address Filtering, Domain Filtering, MAC Filtering, Remote Management and Advanced Security . Click any of them, and you will be able to configure the corresponding function. The detailed expl anations for each submenu a[...]

¾ Enable MAC Filtering - set MAC Address Filterin g is enabled or disabled. You can select the default filtering rules of MAC A ddress Filtering, either Allow or Reny accessing the router. 5.8.2 IP Address Filtering The IP address Filtering feature allows you to control Internet Access by specific users on your LAN based on their IP addresses. The[...]

Keep the field open, which means all LAN IP Addresses have been put into the field. 3. LAN Port - type a LAN Port or a r ange of LAN por ts in the field. For example, 1030 - 2000. Keep the field open, which means all LA N ports have been put into the field. 4. WAN IP Address - type a WAN IP Address or a range of WA N IP Addresses in the field, in d[...]

Figure 5-27: Domain Filtering Before adding a Domain Filtering e ntry, you must ensure that Enable Firewall and Enable Domain Filtering have been selected on the Firew all page. To Add a Domain filtering entry, click the Add New… button. The page " Add or Modify a Domain Filtering entry " will appear, shown in figure 5-28: Figure 5-28: [...]

Click the Next button to go to the next page and the Previous button to return to the previous page. For example, if you want to block t he PCs on your LAN to access websites www.xxyy.com.cn , www.a abbcc.com and websites with .net in the end on the Internet while no limit for other websit es, you should specif y the following Domain filtering list[...]

To add or modify a MAC Address Filter ing entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). For example: 00-0E-AE-B0-00-0B. 2. Type the description of the PC in the Description field. Fox example: John’s PC. 3. Stat us[...]

¾ Web Management Port - Web browser access normally uses the standard HTTP service port 80. This router’s default remote management web port number is 80 . For greater security, you can change the remote management web interface to a custom port by entering that number in this box provided. Choose a n umber between 1024 and 65534, but do not use[...]

¾ Packets S t atistic interval (5 ~ 60) - The default value is 10. Select a value between 5 and 60 seconds in the pull-down list. The Packets S t atistic interval value indicates the time section of the packe ts statistic. The re su lt of the statistic used for analysis by SYN Flood , UDP Flood and ICMP-Flood . ¾ DoS protection - Enable or Disabl[...]

¾ Host IP Address- The IP address that blocked by DoS are displayed here. ¾ Host MAC Address - The MAC address that blocked by DoS are displayed here. To update this page and to show the current blocked host, click on the Refresh button. Click the Clear All button to clear all displayed entri es. After the tabl e is empty the blocked host will re[...]

To delete all the entries: 1. Click the Clear All button. 2. Click the Save button. Note : Y ou can set up to 8 entries. 5.10 DDNS The router offers a Dynamic Domain Name System ( DDNS ) feature. DDNS lets you assign a fixed host and domain name to a dynamic Internet IP Address. It is useful when you are hosting your own website, FTP server , or ot[...]

Figure 5-36: Oray .net DDNS Settings To set up for DDNS, follow these instructions: 1. T ype the User Name for your DDNS account. 2. T ype the Password for your DDNS account. 3. Click the Login button to login the DDNS service. ¾ Connection Status - the status of the DDNS servic e connection is displayed here. ¾ Domain Name - the domain names are[...]

Figure 5-37: Comexe.cn DDNS Settings To set up for DDNS, follow these instructions: 5. T ype the domain names your dynamic DNS service provider ga ve. 6. T ype the User Name for your DDNS account. 7. T ype the Password for your DDNS account. 8. Click the Login button to login to the DDNS service. ¾ Connection Status - The status of the DDNS servic[...]

5.1 1.1 Time Y ou can set time manually or get GMT from the Internet for the router on this p age (shown in figure 5-39): Figure 5-39: T ime settings ¾ Time Zone - Select your local time zone from this pull down list. ¾ Date - Enter your local date in MM/ DD/YY into the right blanks. ¾ Tim e - Enter your local time in HH/MM/SS into the right bla[...]

If the router is not experiencing difficulties, there is no need to download a more recent firmware version, unless that version has a new feature that you want to use. Note: When you upgrade the router's firmware, you may lose it s configuration settings, so make sure you write down the router settings before you upgrade it s firmware. To upg[...]

Figure 5-42: Reboot the router Click the Reboot button to reboot the router. Some settings of the router will take effect only after rebooting, which include: • Change LAN IP Address. (Sys tem will reboot automatically) • MAC Clone (system will reboot automatically) • DHCP service function. • Static address assignment of DHCP server. • We[...]

5.1 1.6 Log This page (shown in figure 5-44) allows you to query the Logs of the router. Figure 5-44: System Log The router can keep logs of all traffic. Y ou can query the logs to find what happened to the router. Click the Refresh button to refresh the logs. Click the Clear Log button to clear all the logs. 5.1 1.7 St atis tics The Statistics pag[...]

IP A ddress The IP Address displayed with statistics Packets T he total amount of packets received and transmitted by the router. Total Bytes The total amount of bytes received and transmitted by the router. Packets T he total amount of packets rece ived and transmitted in the last Packets Statistic interval seconds. Bytes The total amount of bytes[...]

Appendix A: F AQ 1. How do I configure the router to access Internet by ADSL users? 1) First, configure the ADSL modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from your ADSL modem to the W AN port on the router . The telephone cord plugs into the Line port of the ADSL modem. 3) Login to the router , click the “Network”[...]

MAC register , login to the router and cl ick the "Network" menu link on the left of your browser , and then click "MAC Clone" submen u link. On the "MAC Clone" page, if your PC’ s MAC address is pr oper MAC address, click the "Clone MA C Address" button and your PC’s MAC a ddress will fill in the "W[...]

Figure A-5 DMZ 4. I want to build a WEB Server on the LAN, what should I do? 1) Because the WEB Server port 80 will interfere with the WEB management port 80 on the router , you must change the WEB management port number to avoid interference. 2) T o change the WEB management p ort num ber: Login to the router , click the “Security” menu on the[...]

Figure A-7 Virtual Server 5. The wireless stations cannot connect to the router . 1) Make sure the "Wireless Router Radio" is enabled . 2) Make sure that the wireless stations' SSID accord with the router's SSID. 3) Make sure the wireless stations have right KEY for encryption when the router is encrypted. 4) If the wireless con[...]

Appendix B: Configuring the PCs In this section, we’ll introduce how to inst all and configure the TCP/IP correctly in Windows 95/98. First make sure your Ethernet Adapter is working, refer to the adapter ’s manual if needed. 1. Install TCP/IP component 1) On the Windows taskbar , click the Start button, point to Settings , and then click Contr[...]

Figure B-3: Configuration tab 3) Click on Properties . The following TCP/IP Properties window will display and the IP Address tab is open on this window by default. 4) Now you have two ways to configure the TCP/IP protocol below: • Assigned by DHCP Sever a. Select Obt ain an IP address automatically , as shown in the figure below: Figure B-4: IP [...]

Figure B-5: Gateway tab c. Choose Disable DNS on the DNS c onfiguration tab, as shown in the following figure: Figure B-6: DNS Configuration tab • Setting IP address manually a. Select S pecify an IP address on IP Address t ab, as shown in the following figure. If the router's LAN IP addre ss is 192.168.1.1, type IP address is 192.168.1.x (x[...]

Figure B-7: IP Address tab b. T ype the rout er ’s LAN IP address (t h e default IP is 192.168.1.1) into the N e w ga te wa y fi eld on the Gateway tab, and click on the Add button, as shown in the figure: Figure B-8: Gateway tab c. On the DNS Configuration tab, click Enable DNS radio, and type your computer name in to the Host field and a Domain[...]

click Add button . Shown below: Figure B-9: DNS Configuration tab Now , all the configurations are finished , it will take effect af ter reboot. - 58 -[...]

Appendix C: Specifications General S tandards IEEE 802.3, 802.3u, 802.1 1b and 802.1 1g Protocols TCP/IP , PPPoE, DHCP , ICMP , NA T , SNTP Ports One 10/100M Auto-Negotiation WAN RJ45 port, Four 10/100M Auto-Negotiation LAN RJ45 ports supporting Auto MDI/MDIX Cabling T ype 10BASE-T : UTP categor y 3, 4, 5 cable (maximum 100m) EIA/TIA-568 100 Ω ST[...]

Appendix D: Glossary ¾ 108M Super G TM WLAN Transmission Technology - 108M Super G TM WLAN Transmission Technology employs multip le performance-enhancing techniques including packet bursting, fast frames, data compression, and dynamic turbo mode that combine to improve the throughput and ran ge of wireless networking products. Users can experienc[...]

¾ Domain Name - A descriptive name for an address or group of addresses on th e Internet. ¾ DoS ( D enial o f S ervice) - A hacker attack designed to prevent your computer or network from operating or communicating. ¾ DSL ( D igital S ubscriber L ine) - A technology that allows dat a to be sent or received over existing traditional phone lines. [...]