Milan Technology MIL-SM801P manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88

Aller à la page of

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Milan Technology MIL-SM801P. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Milan Technology MIL-SM801P ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Milan Technology MIL-SM801P décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Milan Technology MIL-SM801P devrait contenir:
- informations sur les caractéristiques techniques du dispositif Milan Technology MIL-SM801P
- nom du fabricant et année de fabrication Milan Technology MIL-SM801P
- instructions d'utilisation, de réglage et d’entretien de l'équipement Milan Technology MIL-SM801P
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Milan Technology MIL-SM801P ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Milan Technology MIL-SM801P et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Milan Technology en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Milan Technology MIL-SM801P, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Milan Technology MIL-SM801P, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Milan Technology MIL-SM801P. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    Managed 8 & 9 Port Switches MIL-SM801P Eight 10/100BASE-TX Ethernet port s Plus One 100BASE-FX port MIL-SM801G Eight 10/100BASE-TX Ethernet port s Plus One 1000BASE-SX port MIL-SM800P Eight 10/100BASE-TX Ethernet port s USER GUIDE[...]

  • Page 2

    Regulatory Approval - FCC Class A - UL 195 0 - CSA C22.2 No. 950 - EN60950 - CE - EN55022 Class A - EN55024 Canadian EMI Notice This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe A respecte toutes les exigences du Reglement sur le materiel brouill[...]

  • Page 3

    Table of Content s 1. Introduction Features Intelligent Management Features Package Contents Management Methods Console and T elnet Management Web-based Management SNMP Network Management 2. Hardware Description Front Panel LED Indicators Rear Panel Desktop Installat ion 3. Network Application Desktop Application Segment Application 4. Network Conf[...]

  • Page 4

    4-4-2. SNMP 4-4-2-1. System Options 4-4-2-2. Community S trings 4-4-2-3. T rap Managers 4-4-3. GVRP 4-4-4. LACP 4-4-4-1. Aggregator Setting 4-4-4-2. S tate Activity 4-4-4-3. LACP S t atus 4-5. Switch Reboot 4-6. Xmodem Upgrade 5. Web-Based Management Web Management 5-1. Web Management Home Overview 5-2. Port S tatus 5-3. Port S tatistics 5-4. Admin[...]

  • Page 5

    1 1. Introduction The MIL-SM801P , MIL- SM801G and MIL-SM800P managed series of comp act desktop switches are ideal solutions for network users. They provide wire-speed, Fast Ethern et switching providing high- performance dat a transfer . The switches feature a store-and-forward architecture with auto-learning of source addresses with an 8K-entry [...]

  • Page 6

    2 Features  Conforms to IEEE 802.3, 802.3u, and 802.3x Ethernet S t andards  Eight auto-sensing 10/100Mbps Ethernet RJ-45 port s  Automatic MDI/MDIX crossover for each 10BASE-T/ 100BASE-TX port  One Fixed 100Mbps Fiber port SC/SC single-mode, MT -RJ, VF-45 connector for MIL-SM801P series only  One Fixed 1000Mbps Gigabit Ethernet port[...]

  • Page 7

    3 Package Content s Unpack t he content s of the p acka ge and verify them against the checklist below .  MIL-SM801P , MIL-SM801G or MIL-SM800P switch  Power Cord  Four Rubber Feet  RS-232 console cable  User Guide  W arranty Card If any item is missing or damaged, pl ease cont act your local dealer for service. Management Methods[...]

  • Page 8

    4 2. Hardware Description Front Panel RJ-45 Port s (Auto MDI/MDIX): Eight 10/100 auto-sensing for 10BASE-T or 100BASE-TX connections. Figure 2-1. Front Panel for MIL-SM800P 100BASE-FX Fiber Port: There are 4 types of fiber connectors available for the MIL-SM801P . The distance for mult i-mode fiber cabling can be up to 2 kilometers. However , the d[...]

  • Page 9

    5 LED Indicators Figure 2-4. LED Indicators There are three LED-Indicators (1 00M, LNK/ACT , FDX/COL) for each RJ-45 port. The following table pr ovides descriptions of the LED statuses and meani ng. They provi de a real-time indication of systems operation stat us. LED S t atus Color Description Power On Green Power On On Green The port is operati[...]

  • Page 10

    6 Rear Panel The Console port and 3-pronged powe r plug are located at the Rear Panel of the MIL-SM801P , MIL-SM 801G and MIL-SM800P switches as shown in Figure 2-5. The switches will work with AC in the range 100- 240V AC, 50-60Hz. Figure 2-5. The Rear Panel of the switch Console Port: Console management can be done through the Console Port. It re[...]

  • Page 11

    7 Att aching Rubber Feet A. Make sure the mounting surfac e on the bottom of the switch is grease and dust free. B. Remove adhesive backin g from the rubber feet. C. Apply the rubber feet to each corner on the bottom of the switch. These footpads can pr otect the sw itch from shock and vibration. Figure 2-6. Attaching Rubber Feet to each corner on [...]

  • Page 12

    8 3. Network Application Desktop Application The switch can be used as a stan dalone switch co nnecting personal computers, ser vers, or print servers directly connecting to form small workgroups . Figure 3-1. Desktop Application[...]

  • Page 13

    9 Segment Application For enterprise networks where large data broadcasts are const antly processed, this switch is suitable for individual dep artment users to connect to the corporate backbone. Figure 3-2. Fiber port on MIL-SM 801P s witch extends the distance between workgroups[...]

  • Page 14

    10 4. Network Configuration Connecting a T erminal or PC to the Console Port Console management involves the ad ministration of the switch via a direct connection to the RS-232 consol e port. This port is a female DB- 9 connector . From the main menu of the console prog r am, the user has access to manage the functions of the switch. Figure 4-1. Co[...]

  • Page 15

    11 After the connection betw een switch and PC i s fi nished, turn on the PC and run a terminal emulation program or Hyper T erminal to match the following default characteri stics of the console port: Baud Rate: 9600 bp s Dat a Bits: 8 Parity: none S top Bit: 1 Control flow: None Figur e 4-2. The settings of communication parameters After you have[...]

  • Page 16

    12 4-1 Main Menu There are five items for selection as foll ows: St atus and Counters: Shows the status of the switch. Switch St atic Configuration: Menus to configure the switch. Protocol Related Configuration: Confi gures protocol features. Reboot switch: Rest arts the system or re sets switch to default configuration. Logout: Exits the menu line[...]

  • Page 17

    13 4-2. S t atus and Counters Press the Ta b or Backsp ace key to choose action menu, and then press Enter key to select item.[...]

  • Page 18

    14 4-2-1. Port S tatus Ty p e : Displays the port type of either 10/100TX or Fiber Enabled: A port that is enabled will be di splayed as “Y es”. A port that is disabled will be displayed as “No”. Stat us : Displays the port’s link. “Down” t he port has no link, and “Up” the port has a link with the remote device. Mode: Displays th[...]

  • Page 19

    15 4-2-2. Port Counters The following information provides a view of the current dat a packet information of the unit. The screen is not aut omatically updated. T o see updated stati stics, exit the menu and re-enter . Actions-> Press the Ta b or Backspace key to choose action menu, and then press Enter key to select item <Quit>: Exits the[...]

  • Page 20

    16 4-3. Switch S tatic Configuration Press the Ta b or Backspace key to choose action menu, and then press the Enter key to select item 4-3-1. Administration Configuration[...]

  • Page 21

    17 4-3-1-1. Device Information Device Name: 10 characters can be used to give the switch a uni que name in order to distinguish it on the network. Af ter configuration this name will show at the top of each menu screen. Device Content: 32 characters can be used to describe devices attached. Device Location: 32 characters can be used to give a locat[...]

  • Page 22

    18 4-3-1-2. IP Configuration This menu enables the user to ch ange the default settings of the IP address, subnet mask and gateway. Re booting the s witch is necessary to have the configuratio n change ta ke affect. Note: Always reboot the switch af ter finishing a new configuration. Actions-> <Edit>: Configures all items. When finished, p[...]

  • Page 23

    19 4-3-1-3. Change Username Use this page to ch ange the User Name. 4-3-1-4. Change Password Use this screen to change th e user management passwor d .[...]

  • Page 24

    20 4-3-2. Port / T runk Configuration The menu provides per port configur ation for speed and duplex as well as port trunking. Use the Sp ace key to select the option preferred for each item. 1. Enabled: User can di sable or enable the port. 2. Auto Negotiate: User can set aut o-negotiation to be enabled or disabled. The default is that auto-negoti[...]

  • Page 25

    21 4-3-3. Port Mirroring Configuration Port mirroring is a method for monitoring traffic in switched networks. T raffic through ports can be monitor ed by on e specific port. The traf fic being received or transmitted by the monito red ports will be duplicated into the monitoring port. Press the Sp ac e key to change the configuration of an item. 1[...]

  • Page 26

    22 4-3-4. VLAN Configuration All ports are automatically placed in VL AN 1, the default VLAN. T o create new VLANs, use the Create a VLAN Group menu and add a VLAN. Make sure when you enter a VLAN name you do not leave spaces. For example VLAN2 is correct; VLAN 2 will give an error . The VLAN name can be any 15 alphanumeric characters. S pecial cha[...]

  • Page 27

    23 4-3-4-1. VLAN Configuration Choose a VLAN In the VLAN Configure menu select the type of VLAN you want to configure: No VLAN (default), Port Based, 802.1Q , or 802.1Q with GVRP . Save the configuration. There are 4 different options fo r VLANs to choose from using the space bar: Disabled, Port Based, 802.1Q and 802.1Q with GVRP . Port Based VLANs[...]

  • Page 28

    24 Port Based VLANs T o configure a new VLAN, select Edit and then use the tab key to select items you want to configure. The sp ace bar allows you to select the different options. In the following configuration, por ts 6, 7, and 8 are trunked. After adding a VLAN group, the configuration option Edit a VLAN Group will allow you to change the member[...]

  • Page 29

    25 IEEE802.1Q VLANs If IEEE802.1Q VLANs is selected, all the port s will belong to the default VLAN 1.[...]

  • Page 30

    26 If more than one VLAN is necessary , the addition al VLANs may be cre ated. PVID (Port VID): Set the port VLAN ID that will be assigned to untagged traf fic on a given port. Thi s feature is useful for accommodating devices that you want to particip ate in the VLAN, but don’t support tagging. Only one untagged VLAN i s allowed per port. Other [...]

  • Page 31

    27 4-3-4-2. Create a VLAN Group T o create a VLAN and add tagged /unt agged member ports to it: 1. VLAN Name: T ype a name for the new VLAN using 15 alphanumeric characters and no spaces. 2. VLAN ID: T ype a VID (between 2~4094). The default is 1. 3. Protocol VLAN: Press the S p ace key to choose prot ocol type. When set, this act s as a packet fil[...]

  • Page 32

    28 4-3-4-3. Edit / Delete a VLAN Group Use this menu to edit or delete a VLAN group. Choose <Edit> or <Delete> . Choose the VLAN to delete or edit by using the T AB key . VLAN 1, the default VL AN, can never be deleted. All other VLANs can be deleted using this menu. When editing the chosen VLAN, the user can change the pr otocol VLAN o[...]

  • Page 33

    29 4-3-5. Priority Configuration 1.There are eight (0~7) prio rity levels that can be mapped as high or low priority queues. 2.High/Low Queue Service R atio (High:Low) : User can select the ratio of high priority packet s to low priority packet s . Actions-> <Edit>: Configures all items. When finished press ESC to return to the action menu[...]

  • Page 34

    30 4-3-6.MAC Address Configuration 4-3-6-1.S t atic MAC Address When you add a static MA C address , it remains in the switch's address table regar dless of whether or not the device is physically connected t o the switch. This saves the switch from having to re-learn a device's MAC address when the device is disconnecte d or powered of f[...]

  • Page 35

    31 Edit st atic MAC address 1. Press the <Edit> key to modify a st atic MAC address. 2. Use the t ab key to choose the MAC ad dress that you want to modify and then press enter . 3. Press the <Edit> key to modify all the items. 4. Press ESC to go back to the action me nu line, and then select <Save> to save all configured values. [...]

  • Page 36

    32 4-3-7.Misc. Configuration 4-3-7-1.Port Security A port set in security mode will be “l ocked” and be withou t address learning. Only the incoming packet s with the so urce MAC address already existing in the address table can be for warded. With port security , users can disable a port from learning new MAC addresses. The user may then retur[...]

  • Page 37

    33 4-3-7-2.MAC Age Interval T o configure a dif ferent MAC Age Interv al, type the number of seconds that an inactive MAC address re mains in the switch’s address t able before it is deleted. Once the address is removed from the tabl e, a device will have to send out broadcast packet s to be rele arned by the switch and have its address put in th[...]

  • Page 38

    34 4-3-7-3.Broadcast S torm Filtering Broadcast storm filtering is used to li mit the amount of broadcast traf fic on the network. An excessive amount of br oadcast traf fic can inhibit data packet s from timely delivery . The valid threshold values are 5%, 10 %, 15%, 20%, 25% and NO. If the broadcast traffic is greater than the co nfi g ured value[...]

  • Page 39

    35 4-3-7-4.Max Bridge T ransmit Delay Bound Max bridge transmit delay bound: Limits the packet s queuing time in the switch. If enabled, the packet s exceed ing the queuing time will be dropped. Press the Sp ac e key to set the time. The valid values are 1sec, 2sec, 4sec and Off. Default is OFF . This setting does not depend on what values are set [...]

  • Page 40

    36 4-4.Protocol Related Configuration 4-4-1.STP 4-4-1-1.STP Enable This p age enables or disables the S p anning T ree function. Press the Spac e key to select Enabled or Di sabled.[...]

  • Page 41

    37 4-4-1-2.System Configuration The dat a on the left is f o r display on ly . The parameters on the right can be configured with new values. Priority: The value used to identify the root bri dge. The bridge with the lowest value has the highest priority and is select ed as the root. Enter a number 1 through 65535. Max Age value is the number of se[...]

  • Page 42

    38 4-4-1-3.STP Port Configuration 1. PortSt ate: Port sp anning tree status. 2. PathCost: S pecifies the p ath cost of th e port that the switch uses to determine which port s are the forwar ding ports. If you change the value, you need to rest art the switch for the value change to take ef fect. 3. Priority: S pecifies the p ath cost of the port t[...]

  • Page 43

    39 4-4-2.SNMP Any Network Management st atio n running the Simple Network Management Protocol (SNM P) can manage the swit ch provided that the Management Information Ba se (MIB) is inst alled. SNMP is a protocol that governs the transfer of informati on between management and agent. The switch supports SNMP V1. Use this menu to define management st[...]

  • Page 44

    40 4-4-2-1.System Options Press <Edit> to enter all items and then press <Save> to save the configured values. 1. System Name: Enter a name to be used to identify the switch. 2. System Cont act: Enter the name of the cont act person or organization. 3. System Location: Enter the location of the switch.[...]

  • Page 45

    41 4-4-2-2.Community S t rings Community strings serve as p asswords and can be entered as one of the following : 1. Read only : Enabl es requests accomp anied by this string to display MIB- object information. 2. Read W rite : Enables requests accompanied by this string to display MIB-object information and to set MIB obj ect s. Actions-> <A[...]

  • Page 46

    42 4-4-2-3.T rap Managers A trap manager is a management st ation that receives traps. System alert s are generated by the switch. If no tr ap manager is defined, no trap s are issued. Create a trap mana ger by entering the IP addr ess of the st ation and a community nam e. Actions-> <Add>: Creates a trap manager . <Edit>: Configures[...]

  • Page 47

    43 4-4-3.GVRP Use the GVRP Configurat ion screen to enable or disable GVRP (G ARP VLAN Registration Protocol) support. Press the Sp ac e key to choose Enabled or Disabled. Actions-> <Edit>: Configures all items. When finished, pressing ESC returns to the action menu line. <Save>: Saves all configured val ues. <Quit>: Exit s thi[...]

  • Page 48

    44 4-4-4-1.Aggregator Setting 1. Group: Displays the trunk group ID. NOTE: Before setting LACP support, yo u must first set the trunk group using the Port / T runk Configuration screen. 2. LACP: Press the Sp ace key to enable or disable the LACP (Link Aggregation Control Protocol) suppor t. If enabled, the group is an LACP static trunki ng group. I[...]

  • Page 49

    45 4-4-4-2.S t ate Activity Active: The port automatically se nds LACP protocol p ackets. Passive: The port does not automati cally send LACP protocol packet s and responds only if it receives LACP prot ocol packets from the opposite device. Actions-> <Edit>: Configures all items. When finished, pressing ESC returns to the action menu line[...]

  • Page 50

    46 4-4-4-3.LACP St atus When setting a trunking group, the re lationship st atus information may be seen on the LACP Gr oup S t atus screen. Actions-> <Quit>: Exit s this p age and retu rns to the previous menu. <Previous Page>: Returns to previous p age to view . <Next p age>: Go to next page to view.[...]

  • Page 51

    47 4-5.Switch Reboot Default: Resets the switch to the factory default s . The software version that the switch will be reset to can be fo und on the “System Information” menu under the main menu “S t atus and Counters”. Rest art: Reboots the switch to enable items that have been configured.[...]

  • Page 52

    48 4-6. Xmodem Upgrade 1. First, modify the baud rate of the terminal to 57600bps. Then connect to the switch. 2. Press the X key to start upgrading f or Xmodem. 3. Select “send file" under the "transfer" menu from menu bar . 4. Press the "browse" button to select the path. 5. Select the "1K Xmo dem" of protocol[...]

  • Page 53

    49 5. W eb-Based Management This section introduces the configuration and functions of the web-based management of MIL-SM801P , MI L-SM801G and MIL-SM800P switch series. The managed switch seri es provides an embedded HTML website residing in flash memory . This featur e allows users to manage the switch from anywhere on the network through a stand[...]

  • Page 54

    50 5-1. W eb Management Home Overview 1. Home Page.[...]

  • Page 55

    51 5-2. Port S tatus 1. Port st atus St ate: Displ ays port stat us as of f or on depending on user setting. “Unlink” means the port is of fline or “of f ”. Link St atus: Down is “No Link”, Up is “Link”. Auto Negotiation: Indicates if the port is in auto negotiation mode. Speed st atus: Displays 10 0Mbps or 10Mbp s speed. P o rt s 1[...]

  • Page 56

    52 5-3. Port S t atistics The following information provides a view of the current st atus of the unit. A single port counter as follows:[...]

  • Page 57

    53 5-4.Administrator The management functions include IP address, switch settings, c onsole port information, port controls, link aggregation, filter dat abase, VLAN configuration, sp anning tree, port mirroring, SNMP , security manager , TFTP update firmware, config uration backup, system reset, and reboot. 5-4-1. IP Address The IP Settings can be[...]

  • Page 58

    54 5-4-2-2.Advanced 1. Miscellaneous Settings: MAC Address Age-out Time: T ype the number of se conds that an inactive MAC address remains in the switch's address t able. The valid range is 300~765 seconds. Defa ult is 300 seconds. Max bridge transit delay bound contr ol: Limits t he packet s queuing time in the switch. If enabled, the packet [...]

  • Page 59

    55 2. Priority Queue Service settings: First Come First Service: The sequence of packet s sent is dependent on the order of arrival. The first pack ets in the queue are transmitted before any other packet s. All High before Low: The high priority packet s are sent before the low priority packet s. Weighte d Round Robin: This option enables the user[...]

  • Page 60

    56 3. Protocol Enable Setting: Enable S p anning T ree Protocol: Enables STP . The recommended default is enabled. Enable Internet Group Multicast Protocol: Enables I G MP protocol. IGMP Query Mode: Recognizes different queries from clients or servers to decide which Query will be the fi rst priority . The three modes are: 1. Auto Mode : Chooses th[...]

  • Page 61

    57 4. IGMP Theory of Operation The following three topologies det a il how IGMP Query wor ks and to be configured within a net work: 1. Auto mode needs to be enabled when th e router’s IP address is smaller than other switches in the subnet. 2. IGMP needs to be enabled when the router’s IP address is not smaller than other switches in the subne[...]

  • Page 62

    58 3. The following topology mu st be set when the IP address of the switch i s not the smallest in the subnet. The network will ca use a multi-cast storm from the IGMP client report if it is in Auto mode. All switches must be in disable mode when the VOD server is config ured for IGMP Queryer . Note: It is suggested that the VOD se rver switch hav[...]

  • Page 63

    59 5-4-3. Console Port Information The Windows HyperT erminal program ca n be used to link the switch with the console port. In order to change any of these parameter s, you must be connected to the console port. Bits per seconds: 9600 Da ta bi ts : 8 Parity: none S top Bits: 1 Flow control: none[...]

  • Page 64

    60 5-4-4. Port Controls The menu allows changing of port configurations. St ate: User can disable or enable this po rt. If disabled, there is no network communication through this port. Auto Negotiation: User can set port duplex and port speed to use auto negotiation. Speed setting: User can set 100Mbps or 10Mbp s speed (Port1~Port8) Duplex setting[...]

  • Page 65

    61 5-4-5-1. Aggregator Setting System Priority: A value used to identify the active LACP . The switch with the lowest value has the highest priority and is se lected as t he active LACP . 1. Group ID: T o create a trunk across two or more port s, choose the "Group ID" and click "Get". 2. LACP: If enabl ed, the group supports LAC[...]

  • Page 66

    62 5-4-5-2. Aggregator Information The LACP Aggregator relation in formation is displ ayed as shown. 5-4-5-3. S t ate Activity Active (select) : The active port automatically sends LACP prot ocol packet s. Passive (no select) : The p assive port does not automatically send LACP protocol packet s, but resp onds only if it receives LACP protocol pa c[...]

  • Page 67

    63 5-4-6. Filter Dat abase 5-4-6-1. IGMP Snooping The switch supports IP multicasting. Y ou can enable IGMP via the web management’s configurat ion screen. In addition, you can view dif ference multicast group s , VIDs and member ports, and IP multicast addresses that range from 224.0.0.0 th rough 239.2 55.255.255. The Internet Group Manageme nt [...]

  • Page 68

    64 5-4-6-2. S t atic MAC Address When a stati c MAC address is added, it remains in the switch's address table, regar dless of whethe r or not the device is physically connected to the switch. This saves the switch from having to re-learn a device's MAC address when the device is disconnected or powered-of f. T o add a st atic MAC address[...]

  • Page 69

    65 5-4-6-3. Port Security A port in security mode w ill be “locked” with addres s learning blocked. Only the incoming packet s with SMAC alread y existing in the address t able can be forwarded normally . The us er can disable the port from learning any new MAC addresses, then use th e st atic MAC addresses sc reen to define a list of MAC addre[...]

  • Page 70

    66 5-4-7. VLAN Configuration A V irtual LAN (VLAN) is a logical netw ork grouping that limits the broadcast domain. It allows you to isolate netw ork traf fic so only members of the VLAN receive traf fic from the same VLAN memb ers. Basically , creating a VLAN from a switch is logically equivalent to reconnecting a group of network devices to anot [...]

  • Page 71

    67 5-4-7-1. Basic VLAN Configuration By default, there are no VLANs set for the swit ch. In order to configure any of the different types of VLANs, VLANs need to be enabled in the switch using Settings/Advanced/Protocol Enable Se ttings/VLAN Operational Mode. The following are the choices offered: Port Based VLANs This screen shows the current Port[...]

  • Page 72

    68 Create a VLAN and add t agged member port s. 1. From the main menu, click Administrator -- VLAN co nfiguration. 2. Click Add. 3. T ype a name for the new VLAN. 4. T ype a VID (between 2-4094). The default is 1. 5. From the A vailable port s box, select ports to add to the swit ch and click Add . 6. Click Apply .[...]

  • Page 73

    69 5-4-7-2. Port VID Configure port VID settings From the main T ag-based (IE EE 802.1Q) VLAN pag e, click Port VID Settings. Port VID (PVID) Used for setting the Port VLAN ID that will be assigned to unt agged traffic on a given port. For example, if port 9' s Default PVID is 100, all unt agged packet s on port 9 will belong to VLAN 1 00. The[...]

  • Page 74

    70 5-4-8. Set S p anning T r ee The S p anning-T ree Protocol (STP) is a st andardized method (IEEE 802.1D) for avoiding loops in switched net wor ks. When STP is enabled it ensures that only one path at a time i s ac tive between any two nodes on the network. S p anning-T ree Protocol can be enabled using we b management’s switch setting advance[...]

  • Page 75

    71 Information about the current sp anning tr ee status is displayed in t his ta ble. The priority and path cost can be configured for each port. Click the Apply button to modify the configuration . Description Port Priority A change to the Port Priority affect s which port will be the root port. The lowest number has the highest prio rity . The ra[...]

  • Page 76

    72 5-4-9. Port Mirroring The Port Mirroring feature can monitor traf fic in switched networks. T raf fic transmitted or received on monitored por ts (source port s) will be duplicated to a destination port or mirror port. Analysis S tate: Enables or disabl es th e port mirroring function. Mirror Port s: The port s you want to mirror . All source po[...]

  • Page 77

    73 5-4-10. SNMP SNMP is a prot ocol that governs th e transfer of information between management and agent. The swit ch supports SNMP V1. Any Network Management station ru nning the Simple Netw ork Management Protocol (SNMP) can manage the switch prov ided that the Management Information Base (MIB) is installed. Use this menu to define management s[...]

  • Page 78

    74 3. T rap Manager A trap manager is a management st ation that receives traps. Trap s are the system alerts generated by the switch . If no trap manager is defined, no traps are issued. Create a trap manager by entering the IP address of the station and a co mmunity string. 5-4-1 1.Security Manager The user can change the user name and p assword [...]

  • Page 79

    75 5-4-12. TFTP Update Firmware The following menu options pr ovide some syst em control functions to allow a user to update firmware and re motely boot the switch system: • Executing TFTP software • Copy firmware update version image.bin to TFTP sof tware directory . • In web management select Administrator—TFTP up date firmware. • Downl[...]

  • Page 80

    76 5-4-13-2. TFTP Backup Configuration Use this screen to set the TFTP serv er IP address. Y ou can save current EEPROM value from here, then go to the TFTP Restore Configuration screen to restore the EEPROM value. 5 -4-14. Reset System Reset switch to default configuration. The def ault value is shown below: 5-4-15. Reboot Reboot the switch in sof[...]

  • Page 81

    77 6. T echnical S pecifications This section provides the specificat i ons of MIL-SM800P , MIL-SM801P , and MIL-SM801G switch series. S pecifications Stan da r ds Compliance IEEE 802.3 10BASE-T Et hernet, IEEE 802.3u 100BASE-TX /FX Fast Ether net ANSI/IEEE 802.3 Auto-negotiation Protocol CSMA/CD Max Forwarding and Max Filtering Rate 14,880 pps per[...]

  • Page 82

    78 Wei g h t MIL-SM800P switch: 1060 g MIL-SM801P/G switch series: 1080 ± 20 g Sto r ag e T em p . -40ºC to 70ºC (-40ºF to 158ºF) Operational T emp. 0ºC to 45ºC (32ºF to 1 13ºF) Operational Humidity 10% to 90% (Non-condensing) External Power 100-240V AC, 50-60Hz Power Consumption MIL-SM800P switch: 15 W atts (Max) MIL-SM801P/G switch serie[...]

  • Page 83

    79 7. T roubleshooting This section is intend ed to help you solve some common problems encountered while usi ng the MIL-SM801P , MIL-SMS801G , and MIL- SM800P switch series. Incorrect connections  Faulty or loose cables Look for loose or obviously faulty co nnections. If they appear to be OK, make sure the connecti ons are snug. If that does no[...]

  • Page 84

    80  Cabling RJ-45 port s: Use unshielded twisted- pair (UTP) or shielded twisted-p air (STP) cable for RJ-45 connections: 100 Ω Category 3, 4 or 5 cable for 10Mbps connections or 100 Ω Category 5 cable for 100Mbp s connections. Be sure that the le ngth of any twiste d-pair connection does not exceed 100 meters (328 feet). 100BASE-FX fiber po[...]

  • Page 85

    81[...]

  • Page 86

    [...]

  • Page 87

    [...]

  • Page 88

    90000405 Rev . A[...]