Français dropdown-ico

Janome 712T manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Janome 712T. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Janome 712T ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Janome 712T décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Janome 712T devrait contenir:
- informations sur les caractéristiques techniques du dispositif Janome 712T
- nom du fabricant et année de fabrication Janome 712T
- instructions d'utilisation, de réglage et d’entretien de l'équipement Janome 712T
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Janome 712T ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Janome 712T et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Janome en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Janome 712T, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Janome 712T, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Janome 712T. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    INSTRUCTION BOOK MODEL 712T[...]

  • Page 2

    1 SECTION I ESSENTIAL PARTS Names of Parts ...................................................................... 2 ~ 3 Standard Accessories ................................................................... 3 How to Install the Spool Pin .......................................................... 4 Fundamentals of Operation .......................[...]

  • Page 3

    2 SECTION l ESSENTIAL PARTS Reverse stitch lever Stitch length dial Bobbin winder stopper Bobbin winder spindle Spool pin Pattern selector dial Thread tension dial Bobbin winder thread guide Upper thread guide Thread take-up lever Face plate Thread cutter Presser bar Foot holder Thumb screw Feed dog Needle plate Bobbin Needle clamp Needle clamp scr[...]

  • Page 4

    3 23. 24. 25. Handwheel Stop motion knob Presser foot lifter @4 @5 @3 • Standard Accessories Screwdriver Seam ripper Lint brush Bobbins Set of needles Oil J : Sliding buttonhole foot G : Blind stitch foot E : Zipper foot D : Hemmer foot C : Overedge foot[...]

  • Page 5

    4 For Your Safety 1. While in operation, always keep your eyes on the needle, and do not touch any moving parts such as the take-up lever, handwheel or needle. 2. Do not run the machine: * When making any adjustment in the needle area, such as threading needle, changing needle, or threading bobbin, etc. *W hen attaching or removing parts. * When cl[...]

  • Page 6

    5 • Thread and Needle Chart SECTION II GETTING READY TO SEW • In general, fine thread and needles are used for sewing thin fabrics, and thicker threads and needles are used for sewing heavy fabrics. Always test thread and needle size on a small piece of fabric which will be used for actual sewing. • Use the same thread for needle and bobbin. [...]

  • Page 7

    6 Needle clamp screw • Changing Needles Raise the needle by turning the handwheel toward you and lower the presser foot. Loosen the needle clamp screw by turning it toward you. Remove the needle from the clamp. Insert the new needle into the needle clamp with the flat side facing to the back. When inserting the needle into the clamp, push it up a[...]

  • Page 8

    7 The presser foot lifter raises or lowers your presser foot. Presser foot lifter Foot holder Thumb screw Thumb screw <To Detach> Remove the thumb screw by turning it counter clockwise with the screwdriver. <To Attach> Match the hole in the foot holder with the threaded hole in the presser bar. Fit the thumb screw into the hole. Tighten[...]

  • Page 9

    8 q w e q w q Gently push the slide plate down and slide it toward you. w Lift out the bobbin, as shown. • Removing the Bobbin • Setting Spool e Return the spool pin to its original position. q Turn the spool pin. w Set the spool from the bottom end of the spool pin as illustrated. Slide plate[...]

  • Page 10

    9 q i e r q Turn the stop motion knob counterclockwise to disengage clutch. r Insert the thread through the hole in the bobbin from inside to outside as shown. t Put the bobbin on the bobbin winder spindle, and push it to the right. y While holding the free end of the thread with your hand, pedal the machine. Stop the machine when the bobbin has ma[...]

  • Page 11

    10 q w e q Place the bobbin in the bobbin holder with the thread end unwinding in the clockwise direction. w Guide the thread into the notch “A” on the front side of the bobbin holder. Draw the thread to the left, sliding it between the tension spring blades. r Close the slide plate. Check the threading by referring to the chart shown on the sl[...]

  • Page 12

    11 q w e q w r t y y t r e • Threading the Machine Raise the thread take-up lever to its highest position by turning the handwheel towards you. Raise the presser foot with the presser foot lifter and pass the thread in the order from q to y . q Draw the thread into the thread guide using both hands. w While holding the thread near the spool, draw[...]

  • Page 13

    12 ° For Straight Stitch The ideal straight stitch will have threads locked between the two layers of fabric. ° For Zigzag Stitch In the correct zigzag stitch, the bobbin threads will not show on the right side of fabric and the needle threads will show slightly on the wrong side of fabric. q w e q Raise the presser foot and hold the needle threa[...]

  • Page 14

    13 1 ~ 4 0.3 ~ 4 0.5 ~ 2 1 ~ 3 S. S. 2 ~ 3 • Pattern Selector Dial • Stitch Length Dial When sewing stretch stitch, set the length dial at “S.S.”. If forward and reverse feeds become unbalanced due to the type of fabric, correct the balance as follows: When patterns are compressed, correct it by turning the dial in the direction q so that t[...]

  • Page 15

    14 To drop the feed dogs, turn the stitch length dial to the “ ” mark. Fabric is fed in reverse while the lever is pressed. When it is released, fabric is fed forward. Reverse stitch lever • Reverse Stitch Lever • Dropping the Feed Dogs[...]

  • Page 16

    15 or q w A: Zigzag Foot << Starting Sewing>> While holding the threads with your left hand, turn the handwheel toward you to bring the needle into the fabric where you wish to start sewing. Lower the presser foot, and then start sewing slowly. Machine Setting Stitch Length 1.5 ~ 4 <<Changing Sewing Direction>> q Bring the n[...]

  • Page 17

    16 qw e e Cut the threads with the thread cutter, leaving the thread ends the proper length for starting the next seam. Machine Setting Stitch Length 0.3 ~ 4 A: Zigzag Foot Zigzag width can be adjusted within the range illustrated by the symbol. • Zigzag Stitch <<Securing Seams>> q For fastening the end of seams, press the reverse sti[...]

  • Page 18

    17 Here’s How Place the fabric under the presser foot so that the stitches are made over the edge. NOTE: When using stretch knit fabric, use a blue tip needle, which effectively prevents skipped stitches. or Edge of fabric Guide C: Overedge Foot Machine Setting Stitch Length Machine Setting Stitch Length A: Zigzag Foot This stitch is formed with [...]

  • Page 19

    18 w q or When the needle comes to the left. q Position the fabric on the machine so that the needle just pierces the folded edge of the fabric when the needle comes over to the extreme left side. Lower the presser foot. <<How to Set the Guide>> When the needle comes to the right. Guide screw Sliding guide w Turn the guide screw and mov[...]

  • Page 20

    19 The symbol “ ” (red zone) on the stitch length dial indicates the range of adjustment for the buttonhole. To adjust for coaser stitch for the buttonhole, turn the dial toward "1". For denser stitch for the buttonhole, turn the dial toward "0". y Set the pattern selector dial at “ ”. Sew the right side of the buttonhol[...]

  • Page 21

    20 u Set the pattern selector dial at “ ”. Sew 5 stitches of bartack, and raise the needle from the fabric. Then set the pattern selector dial at “ ” and sew a few stitches to secure the seam. i Remove the fabric from the machine, and cut the sewing threads. Pierce a pin inside the bartack. Then cut the opening with a seam ripper. Be carefu[...]

  • Page 22

    21 qwe E: Zipper Foot 0.2~0.3 cm Wrong side of fabric Machine Setting Stitch Length 1.5 ~ 4 End of opening Right side of fabric Top edge of fabric <<Fabric Preparation>> Put the right side of the fabric together and sew to the end of the zipper opening. Use the reverse to lock the stitches. Baste the zipper opening with stitch length at[...]

  • Page 23

    22 io rtyu !1 !7 !0 r Attach the zipper foot with the pin on the right hand side. t Lower the zipper foot at the bottom of the zipper so that the needle pierces the fold and the zipper tape. y Sew through the fold and the zipper tape to the point where the slider begins. u Lower the needle to hold the fabric and raise the presser foot. i Open the z[...]

  • Page 24

    23 S. S. Machine Setting Stitch Length S. S. A: Zigzag Foot Place right sides of fabric together and seam along the edge. Spread the fabric open flat with the right side of the fabric facing up. Sew feather stitch slowly guiding the fabric so the needle catches the folded edge on each side. Machine Setting Stitch Length A: Zigzag Foot When forward [...]

  • Page 25

    24 0.7cm (1/4˝) 0.7cm (1/4˝) Lower the needle into the fabric and lift the hemmer foot. Insert the folded portion of the fabric into the curl of the hemmer foot. Lower the hemmer foot, and then sew by lifting up the edge of the fabric to keep it feeding smoothly and evenly. To reduce bulk, trim about 0.7 cm (1/4˝) from corners as illustrated. Lo[...]

  • Page 26

    25 q w er e w q SECTION IV CARE OF YOUR MACHINE Setscrew q Remove the needle and presser foot. Remove the setscrew on the left hand side of the needle plate with the screwdriver. Remove the needle plate. w Take out the bobbin. e Lift up the front end of bobbin holder to remove it. q While pushing the front end of slide plate, slide it toward you as[...]

  • Page 27

    26 r t ye w q r Brush off the lint on the feed dogs. t Wipe the hook race with a soft dry cloth. y Clean the bobbin holder with a lint brush and a soft dry cloth. Setscrew q Line up the triangle marks and position the bobbin holder so that the knob fits next to the stopper in the hook race. w Put the bobbin in. e Attach the needle plate with setscr[...]

  • Page 28

    27 For a machine in constant use, oil two or three times a year. If the machine does not work smoothly due to standing idle for some time, apply a few drops of oil at the oiling points, and run the machine rapidly for a minute. Wipe excess oil before sewing. Unscrew and remove the face plate. Apply a few drops of fine quality sewing machine oil to [...]

  • Page 29

    28 Condition 1. Threads have been caught in hook mechanism. 2. The feed dog is packed with lint. 1. The needle thread is not threaded properly. 2. The needle thread tension is too tight. 3. The needle is bent or blunt. 4. The needle is incorrectly inserted. 5. The fabric is not being drawn to the back when sewing is finished. 6. The thread is eithe[...]

  • Page 30

    29 Condition 1. The needle thread tension is too tight. 2. The needle thread and/or bobbin thread is not threaded properly. 3. The needle is too heavy for the cloth being sewn. 4. The stitches are too coarse for the fabric being sewn. * When sewing extremely lightweight materials, place a sheet of paper underneath the fabric. 1. The needle thread t[...]

  • Page 31

    749-800-011 (E-N) Printed in Taiwan[...]

  • Page 32

    “ INSTALLATION INSTRUCTIONS” 1. Lay the machine backwards with bottom towards you and loosen setscrews. 2. After loosening set screws, position and set the machine onto hinges. 3. Tighten setscrews and swing the machine forward into place. Setscrew Bottom view of machine showing the position of setscrews Hinge Setscrew Hinge To operate the mach[...]