HP (Hewlett-Packard) GbE2 manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67

Aller à la page of

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation HP (Hewlett-Packard) GbE2. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel HP (Hewlett-Packard) GbE2 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation HP (Hewlett-Packard) GbE2 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation HP (Hewlett-Packard) GbE2 devrait contenir:
- informations sur les caractéristiques techniques du dispositif HP (Hewlett-Packard) GbE2
- nom du fabricant et année de fabrication HP (Hewlett-Packard) GbE2
- instructions d'utilisation, de réglage et d’entretien de l'équipement HP (Hewlett-Packard) GbE2
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage HP (Hewlett-Packard) GbE2 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles HP (Hewlett-Packard) GbE2 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service HP (Hewlett-Packard) en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées HP (Hewlett-Packard) GbE2, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif HP (Hewlett-Packard) GbE2, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation HP (Hewlett-Packard) GbE2. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    HP Pr oL iant BL p-C lass GbE2 Int er co nnect S w itc h User G uid e Part number: 331399-004 Fourth edition: February 2006[...]

  • Page 2

    2 Legal notices © 2004, 2006 Hewlett-Packard Development Com pany, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Noth ing herein should be construed as constituting an additional w [...]

  • Page 3

    Contents 3 Contents Introduction Overview ................................................................................................................................................ 5 Additional references ............................................................................................................................... 5 Features [...]

  • Page 4

    Contents 4 Accessing the GbE2 In terconnect Switch ......................................................................................... .......... 27 Logging on and configuring th e GbE2 Intercon nect Switch ........................................................................ .. 28 Supporting software and special cons iderations ..........[...]

  • Page 5

    Introduction 5 Intr oducti on Ov ervi e w This user guide provides installation and re ference information for the follow ing kits: • HP ProLiant BL p-Class C-GbE2 Interc onnect Kit • HP ProLiant BL p-Class F-GbE2 Interconnect Kit Additi onal re f er ences Once the GbE2 Interconnect Switch is installed, you are ready to configure it. Detailed i[...]

  • Page 6

    Introduction 6 Figure 2 HP ProLiant BL p-Class GbE2 Interconnect Switch and QuadSX Interconnect Module Fe a t u r e s The ProLiant BL p-Class GbE2 Interconnect Switch and inte rconnect modules are designed for easy installation and high performance in an environment where traffic on the network and the number of users increases continually. Enterpr[...]

  • Page 7

    Introduction 7 • Remote Monitoring (RMON) feature, which all ows ne twork devices to exchange network monitoring data. RMON performs the following major funct ions: • Gathers cumulative statistics for Ethernet interfaces • Tracks a history of statistics for Ethernet interfa ces • Creates and triggers alarms for user-defined events • Quali[...]

  • Page 8

    Introduction 8 GbE2 Interconnect Switch redundancy The ProLiant BL p-Class GbE2 Interconnect Switch offe rs several redundancy and fa ilover features. With these features, the network configuration can be designed to a llow for continued network access to each server blade in case of a component or link failure. GbE2 Interconnect Switch redundan cy[...]

  • Page 9

    Introduction 9 • Statistic monitoring including port utilization, data pac kets received/transmitted, port error packets, trunk utilization, and so on • Ping and trace route capability • Remote syslog with support for pr imary and secondary syslog server • Portable Diagnostic Station option to configure and di agnose a GbE2 Interconnect Swi[...]

  • Page 10

    Introduction 10 G bE 2 I nt erco n ne ct Sw i t ch a rchi t ec tu re The ProLiant BL p-Class system provides integrated switching technology for network cable reduction. The following diagram illustrates the Ethernet signal connectivity between server bays and the interconnect bays through the backplane for the p-Class server enclosure. Figure 3 Et[...]

  • Page 11

    Introduction 11 The following diagram illustrates the Ethernet signal connectivity between server bays and the interconnect bays through the backplane for p-Class server enclosures with en hanced backplane components that support high-density blade servers. Figure 4 Ethernet signal connectivity for server encl osures with enhanced backplane compone[...]

  • Page 12

    Introduction 12 HP Ethernet Connectivity Mapper utility (hpecm) The HP Ethernet Connectivity Mapper is a utility used to determine the NIC name enum eration and the associated mapping to switch ports. The physical connections between server blade network interface controllers (NICs) and switch ports depend on the server blade type and the encl osur[...]

  • Page 13

    Introduction 13 Layer 2 switching technology allows the GbE2 Interconnect Switch to l ook into data packet s and redirect them based on the destination MAC address. This reduces traffic cong estion on the network because pa ckets, instead of being transmitted to all ports, are transm itted to the destination port only. IEEE 802.1Q-based Virtua l Lo[...]

  • Page 14

    Introduction 14 Interconnect Switch can also be uploaded to a TFTP serve r, a configuration file can be downloaded into a GbE2 Interconnect Switch from a TFTP server, and config uration settings can be saved to the TFTP server. Store and forward switching scheme The GbE2 Interconnect Switch provides a store and forward switching scheme that allows [...]

  • Page 15

    Introduction 15 authenticated using a shared key that is not sent over th e network. In addition, the re mote administrator passwords are sent encrypted between the TACACS+ client (the switc h) and the back-end TACACS+ server. The GbE2 Interconnect Switch supports: • Only standard ASCII inbound login auth entication. PAP, CHAP, or ARAP lo gin met[...]

  • Page 16

    Introduction 16 Redundant images in firmware The GbE2 Interconnect Switch can store up to two different software images, called image1 and image2 , as well as boot software, called boot . When you download new software, you are given the ability to specify where it is to be placed: either into image1 , image2 , or boot . For example, if your active[...]

  • Page 17

    Introduction 17 Table 1 GbE2 Interconnect Switch front panel Item Description Status 6 Front panel RJ-45 connector link activity LEDs Green = Link and no activity Green flashing = Link and activity Amber = Port disabled Off = No link 7 Management status LED Flashing = Management sessio n active Off = No management session act ive 8 Power status LED[...]

  • Page 18

    Introduction 18 Figure 7 GbE2 Interconnect Switch fr ont panel NIC LED functions Table 3 GbE2 Interconnect Switch front panel NIC LED functions Item LED Description Status 1 Link speed Amber = 1000 Mb/s Green = 100 Mb/s Off = 10 Mb/s 2 Link activity Green = Link and no activity Green flashing = Link and activity Amber = Port disabled Off = No link [...]

  • Page 19

    Introduction 19 Table 4 QuadT2 Interconnect Module connectors Item Description 5 Port 22 RJ-45 connector for 10/100/1000 Mb uplink for Swit ch A 6 Port 21 RJ-45 connector for 10/100/1000 Mb uplink for Swit ch A 7 Port 20 RJ-45 connector for 10/100/1000 Mb uplink for Swit ch A 8 Port 19 RJ-45 connector for 10/100/1000 Mb uplink for Swit ch A Figure [...]

  • Page 20

    Introduction 20 Figure 10 QuadSX Interconnect Module connectors Table 6 QuadSX Interconnect Module connectors Item Description 1 Port 22 LC fiber connector for 1000SX uplink on Switch B 2 Port 21 LC fiber connector for 1000SX uplink on Switch B 3 Port 20 LC fiber connector for 1000SX uplink on Switch B 4 Port 19 LC fiber connector for 1000SX uplink[...]

  • Page 21

    Setting up and installing th e GbE2 interconnect switch 21 Se tting up and inst alling the GbE2 int er connec t s w itc h Ov ervi e w This chapter describes how to set up and install the Pr oLiant BL p-Class GbE2 Interconnect Switches and the interconnect modules. The setup and installation proc ess includes the following tasks: 1. Installing the G[...]

  • Page 22

    Setting up and installing th e GbE2 interconnect switch 22 1. Insert the interconnect modules into th e bottom-left and bottom-right module bays on the rear side of the server blade enclosure. IMPORTANT: Be sure that the interconnect modules are fu lly seated. The latch/handle will drop into place when the module is firmly seated. Figure 12 Install[...]

  • Page 23

    Setting up and installing th e GbE2 interconnect switch 23 IMPORTANT: If you are replacing an existing GbE2 Inte rconnect Switch, or upgrading from a GbE Interconnect Switch, an RJ-45 Patch Panel, or an RJ-45 Pa tch Panel 2, and you have strict security requirements: Do not cable the GbE2 Interconnect Switch until after configur ation. Or Connect t[...]

  • Page 24

    Setting up and installing th e GbE2 interconnect switch 24 5. On the rear side of the server blade enclosure, insert the new interconnect module into the bottom-left module bay. 6. On the front side of the server blade enclosure, slide a new GbE2 Interconnect Switch fully into the right interconnect bay. 7. Close the ejector lever and let the switc[...]

  • Page 25

    Setting up and installing th e GbE2 interconnect switch 25 • User name and password settings • Default access to variou s management interfaces • Network Time Protocol (NTP) settings IMPORTANT: Refer to the “Runtime switching software default settings” appendix for a complete list of default configuration settings. GbE2 Interconnect Switc[...]

  • Page 26

    Setting up and installing th e GbE2 interconnect switch 26 Table 8 User access levels User account Description and tasks performed Password Administrator The super user administrator has complete access to all men us, information, and configuration commands on the GbE2 Interco nnect Switch, including the ability to change both the user and administ[...]

  • Page 27

    Setting up and installing th e GbE2 interconnect switch 27 To connect the interconnect m odules to the network: 1. Connect your network cables to the interconnect modu les. For connector location s, refer to the “QuadT2 Interconnect Module panel” section or “QuadSX Interc onnect Module panel” section in the “Introduction” chapter. 2. Ga[...]

  • Page 28

    Setting up and installing th e GbE2 interconnect switch 28 2. From a computer connected to the sa me network, use the IP address to a ccess the GbE2 Interconnect Switch using a Web browser or Telnet application. This allows you to access the GbE2 Interconnect Switch browser- based interface (BBI) or command line interface (CLI). Once you have acces[...]

  • Page 29

    Setting up and installing th e GbE2 interconnect switch 29 Supporting softwar e and spec ial consider ations The following supporting software is av ailable to assist you in configuring and managing the GbE2 Interco nnect Switch. • Server Blade and Power Management Module Firmware —Provides firmware and installation instructions required for pr[...]

  • Page 30

    HP ProLiant BL p-Class C-Gb E2 Interconnect Kit Regulato ry Compliance Notices 30 HP Pr oL iant BL p-C lass C-GbE2 In te r connect K it Regulat ory C ompli ance Noti ces Cla ss A eq uipment This equipment has been tested and found to comply with the limits for a Clas s A digital device, pursuant to Part 15 of the FCC Rules. These limits are desi gn[...]

  • Page 31

    HP ProLiant BL p-Class C-Gb E2 Interconnect Kit Regulato ry Compliance Notices 31 Eu ro p e a n U n i o n R e g u l a t o r y N o t i c e This product complies with th e following EU Directives: • Low Voltage Directive 73/23/EEC • EMC Directive 89/336/EEC CE Compliance of this product is valid only if powere d with the correct HP-provided and C[...]

  • Page 32

    HP ProLiant BL p-Class C-Gb E2 Interconnect Kit Regulato ry Compliance Notices 32 BS M I N ot i c e Japanes e Noti ce Ko r e a n N o t i c e[...]

  • Page 33

    HP ProLiant BL p-Class F-GbE2 Interconn ect Kit Regulatory Compli ance Notices 33 HP Pr oL iant BL p-C lass F -GbE2 Inter connect K it R egulatory C ompli ance Noti ces Cla ss A eq uipment This equipment has been tested and found to comply with the limits for a Clas s A digital device, pursuant to Part 15 of the FCC Rules. These limits are desi gne[...]

  • Page 34

    HP ProLiant BL p-Class F-GbE2 Interconn ect Kit Regulatory Compli ance Notices 34 Eu ro p e a n U n i o n R e g u l a t o r y N o t i c e This product complies with th e following EU Directives: • Low Voltage Directive 73/23/EEC • EMC Directive 89/336/EEC CE Compliance of this product is valid only if powere d with the correct HP-provided and C[...]

  • Page 35

    HP ProLiant BL p-Class F-GbE2 Interconn ect Kit Regulatory Compli ance Notices 35 BS M I N ot i c e Japanes e Noti ce Ko r e a n N o t i c e Las er c o mp l ia n c e The fiber optic module contains a laser that is classified as a “Class 1 Laser Produc t” in accordance with US FDA regulations and the IEC 60825-1. The produc t does not emit hazar[...]

  • Page 36

    Technical specifications 36 T ec hni cal s pec if i cati ons Table 9 General specifications Standards IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX Fast Ethernet IEEE 802.3ab 1000Base-T Ethernet IEEE 802.3z 1000Base-SX Etherne t IEEE 802.1D Spanning Tree Protocol IEEE 802.1s Multiple Spanning Tree Protocol IEEE 802.1w Rapid Spanning Tree Prot[...]

  • Page 37

    Technical specifications 37 Table 9 General specifications Number of ports per GbE2 Interconnect Switch 16 x 10/100/1000-Mb/s Nway Ports dedicated t o server blade for GbE2 Interconnect Switch communicatio ns 2 x 10/100/1000-Mb/s Nway Ports dedicated to commu nications between GbE2 Interconnect Switche s A and B 4 10Base-T/100Base-TX/1000Base-T RJ-[...]

  • Page 38

    Technical specifications 38 Table 11 Performance specifications Transmission method Store-and-forward Memory 128MB main, 32MB flash, and 2 MB shared packe t buffer memory per GbE2 Interconnect Switch MAC address table size 2K per GbE2 Interconnect Switch Packet forwarding rate 1,488,095 packets per second with 64 byte pa ckets per port (for 1000 Mb[...]

  • Page 39

    Runtime switching software default settings 39 R untime s w itc hing so ft w ar e def ault se ttings This section provides the default setting s for the GbE2 Interconnect Switch: • Table 12 contains general default settings for both Switch A and Switch B • Table 13 contains port names, VLANs, STP, trun king default settings for Swit ch A and Sw[...]

  • Page 40

    Runtime switching software default settings 40 Table 12 Switch A and Switch B: general default settings Setting Value Bridge Hello Time 2 seconds Bridge Forward Delay 15 seconds Bridge Priority 32768 MAC Address Aging Time 300 seconds Port Priority 128 Path Cost 4 Static VLAN Entry Default VLAN (VID = 1) Port VID 1 for all ports Port Trunking Trunk[...]

  • Page 41

    Runtime switching software default settings 41 Table 12 Switch A and Switch B: general default settings Setting Value Serial Port Data Bit 8 Serial Port Parity Bit None Serial Port Stop Bit 1 Serial Port Flow Control None Default VLAN Default VLAN (VI D=1) with all ports assigned including CPU, STG=1 NTP State Disabled NTP Server 0.0.0.0 NTP Resync[...]

  • Page 42

    Runtime switching software default settings 42 Table 12 Switch A and Switch B: general default settings Setting Value RADIUS Server Timeout 3 RADIUS Backdoor for Telnet Access Disabled Re-ARP Period in Minutes 10 MSTP Disabled MSTP Default Mode RSTP MSTP Region Name None MSTP Region Version 1 MSTP Max Hop Count 20 CIST Bridge Max Age 20 seconds CIS[...]

  • Page 43

    Runtime switching software default settings 43 Table 12 Switch A and Switch B: general default settings Setting Value UFD Link to Disable – Ports None UFD Link To Disable -- Trunks None RMON History Group Number None RMON History Interface MIB to Monitor None RMON History Number of Requested Buckets 30 RMON History Polling Interval 1800 RMON Hist[...]

  • Page 44

    Runtime switching software default settings 44 Table 12 Switch A and Switch B: general default settings Setting Value 802.1x – suptmout 30 802.1x – syrtmout 30 802.1x – maxreq 2 802.1x – raperiod 3600 802.1x – reauth off IGMP off MCAST/BCAST/UCAST of f SNMPv3 – SNMP access read/write enabled SNMPv3 – v1v2 access enabled SNMPv3 – adm[...]

  • Page 45

    Runtime switching software default settings 45 S w itch A and S w itc h B: port name s, V L A N s, S T P , tru n k i ng d efa ul t set ti ngs IMPORTANT: If you have the ProLiant BL p-Class F-GbE2 Inte rconnect Kit opt ion with the QuadSX Interconnect Modules, the management interface supports only 1000M /Full and Auto options for the Speed/Duplex f[...]

  • Page 46

    Runtime switching software default settings 46 Table 13 Switch A and Switch B: port names, VLANs, STP, and trunking defa ult settings Port type Port no. Speed PVID Tag (Y/N) VLAN name Port name STP Trunk group Uplink 20 10/100/1000 (Auto) 1 N Default VLAN Uplink2 Enabled Uplink 21 10/100/1000 (Auto) 1 N Default VLAN Uplink3 Enabled Uplink 22 10/100[...]

  • Page 47

    Performing a serial download 47 P erf or ming a se r ial do w nload Intr oducti on You can perform a serial download of the new GbE2 Interco nnect Switch Operating System firmware, or Boot Code firmware if you want to upgrade a GbE2 Interconnect Switch directly from any existing operating system (OS) or Boot Code images. This procedure requires the[...]

  • Page 48

    Performing a serial download 48 5. After you see the message displayed in step 4, reconfigur e your terminal emulation console with the following parameters. Parameter Value Baud Rate 115200 Data Bits 8 Parity None Stop Bits 1 Flow Control None 6. Press Enter several times on the keyboard of the PC that is connected to the console port of the GbE2 [...]

  • Page 49

    Performing a serial download 49 Ser ial upgr ade of oper ating s y stem f irm war e pr ocedur e Use the following procedure to perform a serial upgrade of the GbE2 Interconne ct Switch Operating System firmware image usually named pGbE2_100.bin . 1. Using the null modem cable, connect the console port of a GbE2 Interconnect Switch to the serial por[...]

  • Page 50

    Performing a serial download 50 6. Press Enter several times on the keyboard of the PC that is connected to the console port of the GbE2 Interconnect Switch. When the console port is successfully communicating with the PC, indicating readiness for image transfer, you see continuous C’s: CCCCCCCCCCCCCCCCC 7. Make sure that the new Switch Operat in[...]

  • Page 51

    Performing a serial download 51 10. After extracting the image, the system prompts you to select which current operating system image (image1 or image2) needs to be updated by the new operatin g system image. It also provides an option ( n ) not to update any and to quit the update procedure. Depending on your selection, 1 or 2, the system updates [...]

  • Page 52

    SNMP MIBs sup port 52 S NMP MI Bs su pport Intr oducti on Management and statistics information is stored in the Gb E2 Interconne ct Switch in the Management Information Base (MIB). The GbE2 Interconnect Switch supports several standard MIBs. Values for MIB objects can be retrieved with any SNMP-based network management software. In addition to the[...]

  • Page 53

    SNMP MIBs sup port 53 • cpqsinfo.mib —Switch identification information • cpqhost.mib —Switch identification information • bt2Network.mib • bt2Physical.mib • bt2Switch.mib • bt2acl.mib • bt2qos.mib • bt2trap.mib • cpqhost.mib • cpqrack.mib • cpqsinfo.mib • dot1x.mib • hpswitchpl.mib • ieee8023ad.mib • rfc1213.mib ?[...]

  • Page 54

    SNMP MIBs sup port 54 The following are the enterprise SNMP traps supported in the GbE2 Intercon nect Switch: Table 14 Supported enterprise SNMP traps Trap name Description bt2SwDefGwUp Signifies that the default gateway i s alive. bt2SwDefGwDown Signifies that the default gateway i s down. bt2SwDefGwInService Signifies that the default gateway is [...]

  • Page 55

    Safe Mode configuration 55 Saf e Mode conf igur atio n Intr oducti on GbE2 Interconnect Switch config uration fi les are specified in text format. Trivial File Transfer Protocol (TFTP) or Secure Copy (SCP) services can to be used to upload and download these text-based configuration files. When these configuration files are downloaded and applied t[...]

  • Page 56

    Safe Mode configuration 56 GbE2 Inter connect S w itc h r eplacement s cenar io u sing a Saf e Mode conf igur ation When an in-production GbE2 Interconnect Switch fails: 1. Remove the failed GbE2 Interconnect Switch. 2. Insert the spare GbE2 Interconnect Switch that was previously configured for safe operation. 3. Upgrade to new firmware if appropr[...]

  • Page 57

    Safe Mode configuration 57 Method 2: Via any switch management interface using TFTP functionality 1. Power up the switch using the Diagnostic Station or by insert ing the switch in a non-production blade enclosure. After resetting the switch to factory settings (if requir ed), login to the switch CL I via the serial console as Adm in . 2. If the sw[...]

  • Page 58

    Electrostatic discharge 58 Electr ost ati c disc har ge Ov ervi e w To prevent damage to the system, be aw are of the precautions you need to fo llow when setting up the system or handling parts. A discharge of static electricity from a fi nger or other conductor may damage system boards or other static-sensitive devices. This type of damage may re[...]

  • Page 59

    RJ-45 pin specification 59 RJ- 4 5 pin spec ifi catio n When connecting the HP ProLia nt BL p-class GbE2 Interconnect Switch to a switch, bridge, or hub, an Ethernet cable is necessary. The following figure displays the standard RJ-45 rec ept acle/connector for 10/100 Mb/s and Gigabit over Copper ports. Table 15 indicates the pin number and wire co[...]

  • Page 60

    Troubleshooting 60 T r oubl eshoot in g This section provides information on solutions to problems that may occur during the configuration and operation of a ProLiant BL p-Class GbE2 Interconnect Switch. The followin g tables provide steps to take before calling your service representative. Following are four tables with basic troubleshooting infor[...]

  • Page 61

    Troubleshooting 61 Table 17 Troubleshooting: Setting up and accessing Problem Possible cause Possible solution The RJ-45 connector on the switch or LED is faulty. • After checking and replacing the cable, if no link LED displays, check whether the port is transferring data. If yes, the LED is faulty. If no, it could be a faulty RJ-45 connector. C[...]

  • Page 62

    Troubleshooting 62 Table 17 Troubleshooting: Setting up and accessing Problem Possible cause Possible solution Password is not accepted by the GbE2 Interconnect Switch using th e remote console interface immediately after a reboot. The GbE2 Interconnect Switch is still working on network convergence. Wait up to 10 seconds, and the password should b[...]

  • Page 63

    Troubleshooting 63 Table 18 Troubleshooting: Configuring Problem Possible cause Possible solution After connecting more than one p ort to another switch or destination device, the port activity LEDs continuously indicate activity. Because there are multiple links across this device and the destination device, they form loops, which cause broadcast [...]

  • Page 64

    Troubleshooting 64 Table 19 Troubleshooting: Using a TFTP server Problem Possible cause Possible solution The TFTP server is not available to connect to or there is connectivity failure between the switch and TFTP server. • Make sure that the IP address of the TFTP server is correct. • Make sure that the TFTP server exists on the same network a[...]

  • Page 65

    Troubleshooting 65 Table 20 Troubleshooting: Upgrading firmware using the serial port Problem Possible cause Possible solution After forcing the GbE2 Interconne ct Switch into the download mode, the console screen displays a message to change the baud rate for your terminal emulation session for XModem transfer and does not display CCCC…. Your te[...]

  • Page 66

    Index 66 Inde x A accessing switch: p rocedure, 27; RADIUS authentication, 14 administrator account password, 26 architecture, switch, 10 B Bootstrap Protoc ol (BOOTP): overview, 14 BSMI regulatory notice, 32, 35 C cabling of switch: procedures, 2 6; reduction fe ature, 6, 10 Canadian regulatory n otice, 30, 33 Carrier Sense Multiple Access with Co[...]

  • Page 67

    Index 67 standards, IEEE /ANSI, 36 store and forward switching scheme, 14 switch replacem ent, safe mode, 56 T templates, safe mode: location, 56; modification, 56 Trivial File Transfer Protocol (TFTP) server: multiple switch configurations, 26; overview , 13; XML configuration, 55 troubleshooting, 60 trunking feature, overview, 13 U upgrading from[...]