Français dropdown-ico

Field Controls 10 manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Field Controls 10. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Field Controls 10 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Field Controls 10 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Field Controls 10 devrait contenir:
- informations sur les caractéristiques techniques du dispositif Field Controls 10
- nom du fabricant et année de fabrication Field Controls 10
- instructions d'utilisation, de réglage et d’entretien de l'équipement Field Controls 10
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Field Controls 10 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Field Controls 10 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Field Controls en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Field Controls 10, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Field Controls 10, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Field Controls 10. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    Installation Guid e Hardware Platform 10 FChwp10[...]

  • Page 2

    [...]

  • Page 3

    Safety Informati on The followi ng are warni ngs or safety guidel ines. A warni ng means dan ger. You are in a situat ion th at could cau se bodil y inju ry. Before you work on any equipment, be aware of the hazards i nvolved wi th electri cal ci rcuitry and be famili ar wi th standard p ractices for preventing acci dents. Qualifi ed Personnel Warn[...]

  • Page 4

    Restricted Access Area Warning The device is intended for insta llation in restricted access areas. A restricted access area is an area to which access can be gain ed only by service personnel throug h the use of a special too l, lock and key, or other means of security, and t hat is cont rolled by the auth ority responsible for the locati on. Waar[...]

  • Page 5

    Power Suppl y Disconnecti on Warning Before working on the device or near power supplies, disconnect the pow er. Waarschuwing Voordat u aan een fr ame of in de nabijheid van voedingen werkt, dient u bij wisselstroom toestellen de stekker v an het netsnoer uit het stopcontact te halen ; voor g elijkstroom toestellen dient u de stroom uit te schakele[...]

  • Page 6

    Hardware Platform 10 Installati on Guide 6 Table of Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Q u a l i f i e d P e r s o n n e l W a r n i n g ...................................... 3 I n s t a l l a t i o n W a r n i n g ...........................................[...]

  • Page 7

    About thi s manua l CER International bv 7 About this manual This document is i ntended for users of the FieldCommand er, ELS- or EWS controllers that are based on the HWP10-platform and explai ns the steps to instal l an d setup the system in your envi ronment. This gu ide contai ns in formation to i nstal l an d configure the uni t i n your netwo[...]

  • Page 8

    Hardware Platform 10 Installati on Guide 8 Installati on This chapt er explain s the instal l ation in detai l and alon g the way it introduces you to some of the concepts important to understand t he operation of your controller uni t. System require ments In order to connect to the controller, you need a vali d TCP/IP network connection and a bro[...]

  • Page 9

    Install ation CER International bv 9 LED indicator Next to the Power Connector there is a green LED on the fro nt panel for indi catin g system status. Thi s LED is li t when power is suppl i ed to the unit . Power connector Power to the controller is accommodated by a DC jack “J9” or by passive power over ethernet connector. The DC jack is att[...]

  • Page 10

    Hardware Platform 10 Installati on Guide 10 (ELS1700 or EWS1700 onl y) VGA Audi o USB (ELS172x only) To be defined !! VGA Audi o USB Serial port The 9-pin port is used to connect your controll er to your serial equi pment. Th e chapter call ed "Serial Interface" uncover s the detail s of ser ial communi cation and pi n-out of the connecto[...]

  • Page 11

    Install ation CER International bv 11 Hardware instal lation You communi cate with the controller over the Ethernet network. I n thi s part of the chapter, you'll learn about th e uni t itsel f and how and where to connect it. There are no configurabl e parts in side. Everything is controll ed and config ured by the software. Physical installa[...]

  • Page 12

    Hardware Platform 10 Installati on Guide 12 Power Over Ethernet In your controller a passive power over E thernet (PoE) scheme is impl emented (see below), usi ng the un used pairs of the LAN port for power. Power can be injected usin g passive POE spli tter which can be ordered se perately. P OE Sp l i t t er Fi el dCo mm ande r LAN P OE Pow er[...]

  • Page 13

    Install ation CER International bv 13 Connecting to the network Before co nnectin g the controll er to the network, yo u mig ht want to consul t your network admin istrator. You can empl oy the controll er at various points i n your ethernet network as shown below. Make sure the IP addres sing scheme of your controller does not interfere with your [...]

  • Page 14

    Hardware Platform 10 Installati on Guide 14 To connect the CER controller to your 10/100base-T network, you can use any standard Category 5 (CAT5). A sui table cabl e is supp li ed. Attach one side to the RJ- 45 socket marked "Ethernet" on the front panel of the uni t and the other to your ethernet hub or switch. Take note of the ser ial [...]

  • Page 15

    IP configurati on CER International bv 15 IP configuration Your CER controller uses the common TCP/IP protocols to provide the connection to the cli ent machi ne over Ethernet. Like any serve r or de vice, it needs a 'uni que' IP number to be addressed. This chapter shows the basic concepts necessary to install and operate the controller,[...]

  • Page 16

    Hardware Platform 10 Installati on Guide 16 For Field Commander controll ers: Assigni ng an IP address on a Field Commander The factory default IP address of the controller is: 10.0.0.1 with netmask 255.0.0.0 . This address wil l suffice when you have a poi nt-to-poi nt connecti on with the controll er or when the local network ID is "10"[...]

  • Page 17

    IP configurati on CER International bv 17 Note: For se curity reasons, it i s strongly recommended to change thi s password. See the User's G uide for in structions. In case you for got the address of FieldComma nder, you can force it to accept a new IP address by way of ARP and PING commands, see later this chapter. Now you should i denti fy [...]

  • Page 18

    Hardware Platform 10 Installati on Guide 18 Caution: Be aware that, when your Fi eldComma nder is assign ed a dynamic address, you may not know which ad dress to enter in order to access it. Use this setti ng wi th care. The "System IP" page shows the followin g in formation: IP: I nternet Protocol DHCP: Dynami c Host Configu ration Proto[...]

  • Page 19

    IP configurati on CER International bv 19 Force new IP address using ARP+PING When Fiel dComman der is outside of your subnet or or you don't recall it's current address, you cannot open the configurati on web pages to change the IP setting s. To solve this, you can force Fiel dCommander to accept a new IP address by way of ARP and PING c[...]

  • Page 20

    Hardware Platform 10 Installati on Guide 20 For ELS controllers: Assigni ng an IP address on an ELS controlle r The IP address o n an ELS controll er is defined i n a configurat ion fi le and set to 10.0.0.1 by default. To change thi s IP address, connect to the ELS using an US B keyboard, SSH or the ser ial console. Then log i n usi ng username / [...]

  • Page 21

    IP configurati on CER International bv 21 For EWS controllers: Assigni ng an IP address on an EWS controll er The IP address o n an EWS controll er is defined i n a configu ration fi le and set to 10.0.0.1 by default. To change thi s IP address, connect to the ELS using an US B keyboard, SSH or the ser ial console. Then log i n usi ng username / pa[...]

  • Page 22

    Hardware Platform 10 Installati on Guide 22 Testing the Etherne t connection The ping test The most basic way to test the network connection i s to do a so-called 'pi ng' test. When the connection i s working, th e CER controller wil l answer with an 'echo' or 'pong'. Start a command prompt on your l ocal machi ne and [...]

  • Page 23

    Serial interfaces CER International bv 23 Serial interface In this part of the i nstal lati on manu al, you wi ll learn some basics of serial communi cation, th e hardware invol ved and how the CER controll er connects to your RS- 232 device. RS-232 The RS-232c standard The RS-232 stan dard (RS stand s for r ecommended standards ) was publ ish ed f[...]

  • Page 24

    Hardware Platform 10 Installati on Guide 24 RS-485 (option only) The RS-485 standard The RS-485 commun icati on protocol i s the ind ustry's most widely used bi di rectional , balan ced transmissi on li ne standa rd. It is specifical ly desi gned for indu strial mul ti-d rop systems that shoul d be able to transmi t and receive data at hi gh r[...]

  • Page 25

    Serial interfaces CER International bv 25 Network topology and wi ring Mult i-drop RS- 485 i mpli es that th ere are two main wires in a segment l abeled DATA + and DATA– or simp le A and B. The wi ring comes as a twisted pair. To reduce e lectrical noise, it sh ould be twi sted as ti ghtl y as possibl e. It is advisabl e to follow the stan dard [...]

  • Page 26

    Hardware Platform 10 Installati on Guide 26 Automatic Data Flow Control Function for RS-485 The CER controller automat ical ly senses the directi on of incomi ng data an d switch es its transmissi on di rection accordingl y. Therefore no handshaking si gnal (e.g. RTS sig nal) is necessary. This feature lets you simpl y and qui ckly bu il d an RS-4 [...]

  • Page 27

    Serial interfaces CER International bv 27 Ports on your controll er Hardware Platform 10 has di fferent versions, depending on the model you choose: Model USB* Port 1** Port 2 Port 3 Port 4 ELS1700 2xUSB2.0 RS-232 - - - ELS1722 2xUSB2.0 RS-232 RS -232 - - ELS1724 2xUSB2.0 RS-232 RS -485 - - EWS1700 2xUSB2.0 RS-232 - - - EWS1722 2xUSB2.0 RS-232 RS -[...]

  • Page 28

    Hardware Platform 10 Installati on Guide 28 - + Pin Assignments RS-232 and RS-485 Serial Ports Pin RS-232 RS-232 full RS-485 Port 1 Port 2/3 (Option only) Port 2 (Opti on only) 1 - DCD DATA– (B) i nvertin g 2 RxD RxD DATA+ (A) non- inverti ng 3 TxD TxD - 4 - DTR - 5 GND GND GND 6 - DSR - 7 - RTS - 8 - CTS - 9 - RI - Power Connector Pin di ameter:[...]

  • Page 29

    Pin Assi gnment s CER International bv 29 Ethernet pin Col or pair functi on 1 Orange/Whit e 2 TX+ 2 Orange 2 TX- 3 Green/White 3 RX+ 4 Blue 1 POE: VCC in (D C 7-20V) 5 Blue/Wh ite 1 POE: VCC in (D C 7-20V) 6 Green 3 RX- 7 Brown/Whit e 4 POE: GND (power return) 8 Brown 4 POE: GND (power return) USB Ports Pin Si gnal 1 +5V DC 2 D – 3 D + 4 GND[...]

  • Page 30

    Hardware Platform 10 Installati on Guide 30 VGA Note: In the ELS an Award BIOS is used. The combinati on of Award BIOS and Linux kernel wil l d etect a VGA monitor at bootti me, and won’t boot when no moni tor is connected. Pin Signal 1 VGARed 2 VGAGreen 3 VGABlue 4 nc 5 GND 6 GND 7 GND 8 GND 9 KBVCC +5V 10 GND 11 ncc 12 DDC data 13 HS Hor.Sync 1[...]

  • Page 31

    Technical Specifi cati ons CER International bv 31 Technical Specif ications Hardware CPU (type A ) 433MHz AMD Geo de LX700 (type B/C) 500MHz AMD Geo de LX800 Memory (type A) 128 MB SDRAM (type B/C) 256 MB SDRAM Storage (type A/B) 1GB GB Flash drive (256MB rese rved for system) (type C) 4GB GB Flash drive (25 6MB reserv ed for system) Indicators Po[...]

  • Page 32

    Hardware Platform 10 Installati on Guide 32 RS-485 Interface (option only) Interface one RS-485 ser ial port (EIA/TIA-485 -A, ISO 84 82) Connector D-sub 9 pins Distance 1220 meter max (400 0 feet) Data bits 5, 6, 7 or 8 Stop bits 1, 1½ or 2 Parity Even, Odd, Mark, Space, None Flow control Automatic Signals DATA+ (A), DATA– (B), GND Network Inter[...]

  • Page 33

    Physical Dimen sions CER International bv 33 Physical D imensions All sizes in millimet ers[...]

  • Page 34

    Hardware Platform 10 Installati on Guide 34 Notice to the user Regulatory FCC Notice This device complies with Part 15 o f the FCC Rules. Operation is subject to the fo llowing two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including int erference that may cause undesir[...]

  • Page 35

    Notice to the user CER International bv 35 Declaration of Conf ority Trademarks CER and FieldCommander are registered trademarks of CER International bv. All other product names and ser vices identified throughout this book are trademarks or registered trademark s of their respe ctive companies. They are used throughout this manual in editorial fas[...]

  • Page 36

    The latest documentati on is available from http://www.cer.com FieldCommander is a pr oduct of: CER International bv Postbus 258 NL 4700 AG Ro osendaal The Netherlands TEL: +31 (0)165 5 5741 7 FAX: +31 (0)165 5 62151 http:// www.cer.com Part no. FCHWP10IG, r evision 3.5.34[...]