Enviro 50-1386 manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23

Aller à la page of

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Enviro 50-1386. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Enviro 50-1386 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Enviro 50-1386 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Enviro 50-1386 devrait contenir:
- informations sur les caractéristiques techniques du dispositif Enviro 50-1386
- nom du fabricant et année de fabrication Enviro 50-1386
- instructions d'utilisation, de réglage et d’entretien de l'équipement Enviro 50-1386
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Enviro 50-1386 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Enviro 50-1386 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Enviro en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Enviro 50-1386, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Enviro 50-1386, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Enviro 50-1386. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    PLEA SE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE SHERWOOD INDUSTRIES IS AN ENVIRONMENT ALL Y RESPONSIBLE COMP ANY . THIS MANUAL IS PRINTED ON RECYCLED P APER. 50-1386 PELLET STOVE Empr ess TECHNICAL MANU AL PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD R[...]

  • Page 2

    T able of Contents 2 Introduction......................................................................................................... ...3 Rating Label Location.....................................................................................3 Important Safety Data.................................... ........................................[...]

  • Page 3

    3 Introduction * This manual is designed for the technician in conjunction with the owner’s manual. * R ATING L ABEL L OCATION : The rating label is located on the hopper top behind the surr ound panel. I MPORTANT S AFETY D ATA : Please read this entire Owner’s Manual before installing or operating this ENVIRO Pellet Stove. Failure to follow th[...]

  • Page 4

    4 Introduction ELECTRICAL: The use of a surge protected power bar is recommended. The unit must be grounded. The grounded electrical cord should be connected to a standard 120 volts, 60 hertz electrical outlet and also must be accessible. If this power cord should become damaged, a replacement power cord must be purchased from the manufacturer or a[...]

  • Page 5

    5 Inst alla tion R EMOVING P ELLET S TOVE F ROM P ALLET : Figure 1: Removing Stove From the Pallet. Use a flathead screwdriver or 5 / 16 ” socket to remove the four (4) screws that secure the Empress FPI to the pallet. T wo (2) of the screws ar e shown in Figure 1 and the other two (2) are in the same location but on the opposite side; behind the[...]

  • Page 6

    Inst alla tion 6 1 2 " ( 3 0 . 5 c m ) M a n t l e 36" (91cm) 3" (7.6cm) 24" (61cm) Fl o o r P r o t e c t i o n ; M i n 6 " ( 1 5 c m ) i n f r o n t o f d o o r Figure 4: Empress FPI Clearance to Combustibles. C LEARANCES TO C OMBUSTIBLES : 42 5 / 8 " (1083mm) 24 1 / 16 " (611mm) 28 9 / 16 " (725mm) 31 3 / [...]

  • Page 7

    Inst alla tion M ASONRY F IREPLACE I NSTALLATION : If installing the Empress with a skirt the skirt must be installed before the installation. A non-combustible hearth pad must cover combustible flooring underneath, as well as 6” (150 mm) in front of the heater and 6” (150 mm) to the side of the heater . 1. Install the hearth pad. 2. Lock the f[...]

  • Page 8

    8 Inst alla tion P OSITIVE F LUE C ONNECTION WITHOUT A F ULL R ELINE (USA O NLY ): This unit does not require a f ull reline (in USA only) when installing into a masonry fireplace, however , it is recommended to ensure proper dr afting of the appliance. IMPOR T ANT : Ensure the chimney and firebox are cleaned and free of all debris, including soot [...]

  • Page 9

    I NSTALLATION OF C AST S KIRT O PTION : Figure 9: Assembling Cast Skirt. Inst alla tion A DJUSTING H OPPER H EIGHT : The back height of this unit can be set to one (1) of three (3) heights; 19 13 / 16 ” (503 mm), 20 13 / 16 ” (529 mm), 21 13 / 16 ” (554 mm). The hopper should be set to the maximum height that can be used in the installation. [...]

  • Page 10

    1. Install the wall thermostat in a location that is not to close too the unit but will effectively heat the desired area. 2. Install a 12 or 24 V olt Thermostat using an 18 x 2 gauge wire from the unit to the thermostat. Figure 1 1: Mother Board. This control board can be placed into three (3) different modes: Full Auto ON/OFF , High/Low Thermosta[...]

  • Page 11

    11 Inst alla tion S LIDER /D AMPER S ETTING : This is used to regulate the airflow through the pellet stov e. THE SLIDER / DAMPER MUST BE SET AT TIME OF INSTALLATION. A Qualified Service Technician or Installer must set the Slider Damper . More Air Less Air Figure 15: Slider / damper positions. The slider damper is located behind the cast doors and[...]

  • Page 12

    T roubleshooting DO NOT: ● Service the stove with wet hands. The stove is an electrical appliance, which may pose a shock hazard if handled improperly. Only qualified technicians should deal with possible internal electrical failures. ● Do not remove from the firebox any screws without penetrating oil lubrication. ● Hold the ON / OFF BUT TON [...]

  • Page 13

    13 T roubleshooting ü Check the exhaust blower voltage across the blower wires (>=114V on #5 setting and >= 82V on #1 setting). – Replace the Circuit Board if the Voltage reading is less than 82V. with a line voltage >115V AC. ü Check vacuum levels in the exhaust channel by bypassing the vacuum switch, then remove the v acuum hose from[...]

  • Page 14

    T roubleshooting Auger light flashes but auger motor does not turn at all. ü If the auger gear box does not turn but the motor ’ s armature does try to spin then the auger is jammed. – T ry to break apart jam by poking at the jam through the drop tube. If this fails then empty the hopper and remove the auger co ver **remember to re-seal the co[...]

  • Page 15

    15 Connect Thermostat Here Red Red Red Red Brown Brown Brown Brown Thermostat Selector Pins White White White 115V White 220V Blue White White Orange Orange Orange Orange Yellow Yellow Grey Grey Grey Grey Purple Purple Blue 115V Black 220V Brown Black Black Black Blue Daughter Board Vacuum Switch Combustion Blower Power Cord Ground Ignitor 120 o F [...]

  • Page 16

    P ar ts List Reference Number Description Part Number 1 120 °F (49 °C) Ceramic F an T emperature Sensor EC -001 Domestic Power Cor d - 115V EC -042 2 Auger Motor - 115V EF-001 3 High Limit T emp Sensor 200 °F (93 °C) Manual Reset EF-016 Silicone Hose EF-018 4 Ash P an Latch EF-060 P ellet Stove Cleaning Brush EF-156 5 Convection Blower - 115V E[...]

  • Page 17

    17 P ar ts List Reference Number Description Part Number 15 Exhaust Starter T ube 3” Quick Connect 50-1391 16 Mother Board - 120V 50-1392 17 Daughter Board - 120V 50-1393 18 Slider Damper & Lever 50-1394 19 Exhaust Starter Elbow Quick Connect 50-1395 20 Exhaust Starter Gasket 50-1396 21 Daughter Board Decal 50-1397 22 Ignitor & Intak e T [...]

  • Page 18

    P ar ts Diagr am - Components 3 Empress - Fireplace Insert Components October 2006 1 9 8 1 1 2 12 14 21 17 16 5 10 18[...]

  • Page 19

    19 P ar ts Diagr am - P ar ts 6 Empress - Fireplace Insert Parts October 2006 30 32 13 22 4 18 25 23 28 24 26 27 7 31 29 19 15 20[...]

  • Page 20

    20 W arr anty Sherwood Industries Ltd. is the manufacturer of the Enviro line of heating products. At Sherwood Industries, our commitment to the highest level of quality and customer service is the most important thing we do. Each Enviro stove is built on a tradition of using only the finest materials and is backed by our Exclusive Li fetime Limite[...]

  • Page 21

    W arr anty Exclusions and Limitations: 1. This Warr anty does not co ver tarnish, discoloration or wear on the plating or paint. 2. This Warr anty ex cludes wear and tear or breakage caused by cleaning, moving or service on log set. 3. A qualified installer must install this stove or fireplace. This Limited W arr anty covers def ects in materials a[...]

  • Page 22

    22 W arr anty 17 . Damage to plated surfaces caused by fingerprints, scratches, melted items, or other external scores and residues left on the plated surfaces fr om the use of abrasiv e cleaners or polishes is not covered in this warr anty . 18. The Limited W arr anty does not cover tarnish, discolor ation or wear on the plated surfaces. 19. The p[...]

  • Page 23

    23 NAME OF OWNER: _________________________________________ ADDRESS: _________________________________________ _________________________________________ _________________________________________ PHONE:___________________________________ NAME OF DEALER: _________________________________________ ADDRESS: _________________________________________ ____[...]