Français dropdown-ico

Bunn HC-3 manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Bunn HC-3. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Bunn HC-3 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Bunn HC-3 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Bunn HC-3 devrait contenir:
- informations sur les caractéristiques techniques du dispositif Bunn HC-3
- nom du fabricant et année de fabrication Bunn HC-3
- instructions d'utilisation, de réglage et d’entretien de l'équipement Bunn HC-3
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Bunn HC-3 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Bunn HC-3 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Bunn en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Bunn HC-3, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Bunn HC-3, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Bunn HC-3. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    B UNN ® OPERA TING & SERVICE MANUAL BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 27591.0000 6/00 ©1996 Bunn-O-Matic Corporation HC-2 HC-3 (SERIAL # HC00025000 - UP) DISCONTINUED VERSION The information in this manual is no longer current.[...]

  • Page 2

    2 INTRODUCTION This equipment dispenses hot beverages on demand from powered product. It has two or three hoppers. The two and three hopper models may also dispense cold beverages from powdered product from their left dispense station. It is for indoor use only on a sturdy counter or shelf. WARRANTY Bunn-O-Matic Corp. (“Bunn”) warrants the equi[...]

  • Page 3

    3 00656.0000 00831.0000 11646.0000 12368.0002 26525.0000 27620.0000 USER NOTICES Carefully read and follow all notices on the equipment and in this manual. They were written for your protection. All notices are to be kept in good condition. Replace any unreadable or damaged labels. 27591 061500[...]

  • Page 4

    4 INITIAL SET-UP 1. Locate the drip tray assembly beneath the dispenser nested in the packing material. 2. Remove the drip tray and the drip tray cover and set them aside. 3. Remove the water strainer assembly from the drip tray and set it aside. 4. Remove the four legs from the drip tray, apply non-skid pads to the bottom of the legs and securely [...]

  • Page 5

    5 PLUMBING HOOK-UP 1. Securely attach the short piece of tubing on the water strainer assembly to the inlet fitting on the bottom of the dispenser. 2. Flush the water line and securely attach it to the flare fitting on the water strainer assembly. 3. Turn-on the water supply. INITIAL fill & heat CAUTION - The dispenser must be disconnected from[...]

  • Page 6

    6 DRAINING THE HOT WATER TANK CAUTION - The dispenser must be disconnected from the power source throughout these steps. 1. Disconnect the dispenser from the power source. 2. Open front door and place tank heater switch in the “ OFF ” (upper) position. 3. Shut-off and disconnect the incoming water supply. 4. Remove the top panel. 5. Gently remo[...]

  • Page 7

    7 PROBLEM Product will not dispense PROBABLE CAUSE 1. No water 2. No power or incorrect voltage to the dispenser 3. Dispense switch 4. Dispense solenoid valve (Hot or Cold) 5. Solenoid valve (Inlet) 6. Level control board and probe 7. Overflow protection switch 8. Auger drive REMEDY Water lines and valves to the dispenser must be open. (A1) Check t[...]

  • Page 8

    8 TROUBLESHOOTING (cont.) PROBLEM Product will not dispense (cont.) Water is not hot Spitting or excessive steaming PROBABLE CAUSE 9. Water strainer 10. Lime build-up CAUTION - Tank and tank compo- nents should be delimed regularly depending on local water condi- tions. Excessive mineral build-up on stainless steel surfaces can initiate corrosive r[...]

  • Page 9

    9 TROUBLESHOOTING (cont.) PROBLEM Dripping from dispense tip Water flows into tank continuously PROBABLE CAUSE 1. Lime build-up CAUTION - Tank and tank compo- nents should be delimed regularly depending on local water condi- tions. Excessive mineral build-up on stainless steel surfaces can initiate corrosive reactions result- ing in serious leaks. [...]

  • Page 10

    10 TROUBLESHOOTING (cont.) PROBLEM Product overflows container Weak product PROBABLE CAUSE 1. Dispense switch 2. Dispense solenoid valve (Hot or Cold) 1. Water temperature 2. Whipper motor 3. Frother 4. Dispense solenoid valve (Hot or Cold) 5. Auger drive 6. Auger spring 7. Auger motor REMEDY Refer to Service - Dispense Switch for testing procedure[...]

  • Page 11

    11 TROUBLESHOOTING (CONT.) PROBLEM Dispenser is making unusual noises Excess dust Display not lit PROBABLE CAUSE 1. Plumbing Lines 2. Water Supply 3. Tank Heater 1. Fan 2. Hopper Delay Board 3. Transformer (240V 2 Wire Models Only) 1. Lamp 2. Lamp Holder 3. Starter - Lamp 4. Ballast REMEDY Plumbing lines should not be rest- ing on the counter top. [...]

  • Page 12

    12 SERVICE This section provides procedures for testing and replacing various major components used in this dispenser should service become necessary. Refer to Troubleshooting for assistance in determining the cause of any problem. WARNING - Inspection, testing, and repair of electri- cal equipment should be performed only by qualified service pers[...]

  • Page 13

    13 SERVICE AUGER DRIVE COMPONENTS (cont.) If voltage is present as described, proceed to #5. If voltage is not present as described, refer to the wir- ing diagrams and check the dispenser wiring harness. 5. With the wires removed from the motor to be tested. Check for continuity across the two ter- minals on the bottom of the auger motor. If contin[...]

  • Page 14

    14 SERVICE (cont.) AUGER DRIVE COMPONENTS (cont.) 14. Install hopper assy (21) in the dispenser by slid- ing hopper assy in the guides on the hopper sup- port plate (20) until the slot in the bottom rear the hopper seats against the shoulder screw (19) in the hopper support plate. Auger Drive Motor (Refer to Fig. 2) 1. Disconnect the wires from the[...]

  • Page 15

    15 SERVICE (cont.) BALLAST FIG. 4 BALLAST Location The front door lamp ballast is located on the front center of the base behind the front panel. Test Procedure 1. Disconnect the dispenser from the power source. 2. Disconnect the two terminal plug of the door in- terconnect harness from the connector of the ballast. 3. Check the voltage across the [...]

  • Page 16

    16 SERVICE (cont.) CONTROL THERMOSTAT MECHANICAL ELECTRONIC (OPTIONAL) FIG. 6 CONTROL THERMOSTAT P1199.45 P1203.45 Location Mechanical Thermostat The mechanical thermostat is located on the upper right side of the rear panel inside the dispenser. Electronic Thermostat (Optional) The electronic thermostat is located on the right front side of the ba[...]

  • Page 17

    17 SERVICE (cont.) CONTROL THERMOSTAT (cont.) Removal and Replacement. Mechanical Thermostat 1. Disconnect the wires from the thermostat. 2. Remove the thermostat capillary bulb by firmly pulling-up on the capillary at the tank lid. This will disengage the grommet from the tank lid. 3. Remove the #8-32 screw securing the thermo- stat to the rear pa[...]

  • Page 18

    18 SERVICE (cont.) DISPENSE SWITCH P1196.70 Location: The dispense switches are located on the lower outside of the dispenser door. NOTE : The center dispense switch is for HC-3 Models only. Test Procedure: 1. Disconnect the dispenser from the power source. 2. Open the dispenser door and remove the bottom door cover. 3. Disconnect the connector of [...]

  • Page 19

    19 SERVICE (cont.) FAN FIG. 10 FAN P1199.45 Location: The fan is located inside the front panel, mounted on a plate beneath the hopper mounting plate. Test Procedures: 1. Disconnect the dispenser from the power source. 2. Disconnect the black and white wires from the black leads on the fan. 3. Check the voltage across the black and white wires on t[...]

  • Page 20

    20 SERVICE (cont.) FROTHER AND WHIPPER MOTOR FIG. 11 FROTHER AND WHIPPER MOTOR P1203.45 Location: The frothers are located behind the dispenser door, mounted on the front of the front panel inside the whipper chamber. The whipper motors are located on the back side of the front section of the front panel. NOTE: The center position is for HC-3 Model[...]

  • Page 21

    21 SERVICE (cont.) FROTHER AND WHIPPER MOTOR (cont.) 4. Remove dispense tip (3) and twist the whipper chamber (4) clockwise and pull it off the whipper chamber receptacle (8). 5. Pull the frother (6) off the motor shaft. Notice the flat side on the shaft and the matching flat inside the frother. It is important that these two flats are lined up whe[...]

  • Page 22

    22 SERVICE (cont.) HOPPER DELAY BOARD FIG. 13 HOPPER DELAY BOARD P1199.45 Location The hopper delay board is located on the left front side of the dispenser base just behind the front panel. Test Procedures: 1. Disconnect the dispenser from the power source. 2. Disconnect the white and black wires of the hopper delay board harness from the main wir[...]

  • Page 23

    23 SERVICE (cont.) FIG. 14 HOT/COLD SWITCH P1199.45 HOT/COLD SWITCH (Optional) Location: The hot/cold switch is located on the left side of the front panel. Test Procedure: 1. Disconnect the dispenser from the power source. 2. Disconnect the four pin plug from the hot/cold switch and the four pin connector on the main wiring harness. 3. Press the l[...]

  • Page 24

    24 SERVICE (cont.) LAMP HOLDER FIG. 16 LAMP HOLDERS P1209.75 Location: The lamp holders are located on the front of the reflector behind the display panel. Test Procedure: 1. Disconnect the dispenser from the power source. 2. Disconnect the plugs on the door wiring harness from the connectors on the lamp holders. 3. Remove lamp from lamp holders. 4[...]

  • Page 25

    25 SERVICE (cont.) LAMP STARTER and SOCKET (120V, 120/208V & 120/240V Models Only) Location: The lamp starter (6) is located inside the door assy (1) on the top of the door bottom cover (5). Test Procedures: 1. Disconnect the dispenser from the power source. 2. Disconnect the plug on the starter leads from the connector on the door wiring harne[...]

  • Page 26

    26 SERVICE (cont.) LEVEL CONTROL BOARD AND LEVEL PROBE FIG. 17 LEVEL CONTROL BOARD AND PROBE P1203.45 Location: The level control board is located on the upper right rear of the front panel just in front of the tank. The Level probe is located on the right center of the tank lid. Test Procedure: 1. Disconnect the dispenser from the power source. 2.[...]

  • Page 27

    27 SERVICE (cont.) LEVEL CONTROL BOARD AND LEVEL PROBE (cont.) If voltage is present as described, reinstall the probe, the level control board and level probe are operating properly. If voltage is not present as described, check the pink probe wire for continuity. Removal and Replacement: 1. Remove all wires from the level control board. 2. Remove[...]

  • Page 28

    28 SERVICE (cont.) OVERFLOW PROTECTION SWITCH FIG. 21 OVERFLOW PROTECTION SWITCH P1199.45 Location: The overflow protection switch is located in- side the copper overflow cup on the upper front of the tank. Test Procedures: 1. Disconnect the dispenser from the power source. 2. Remove the wire nuts connecting the red wires from the overflow protecti[...]

  • Page 29

    29 SERVICE (cont.) RUN/RINSE SWITCH FIG. 23 RUN/RINSE SWITCH P1199.45 Location: The run/rinse switch is located on the right side of the front panel. Test Procedures: 1. Disconnect the dispenser from the power source. 2. Check for continuity between center terminals and the upper terminals with the switch in the “ RUN ” lower position. Continui[...]

  • Page 30

    30 SERVICE (cont.) SOLENOID VALVE (COLD WATER - OPTIONAL) FIG. 25 COLD WATER SOLENOID VALVE P1214.45 Location: The cold water solenoid valve is located on the left side of the dispenser base just behind the hop- per delay board. Test Procedures: 1. Disconnect the dispenser from the power source. 2. Disconnect the white and white/yellow wires from t[...]

  • Page 31

    31 SERVICE (cont.) SOLENOID VALVE (COLD WATER - OPTIONAL) (cont.) FIG. 26 COLD WATER SOLENOID TERMINALS P1215 SOLENOID VALVES (DISPENSE) FIG. 27 DISPENSE SOLENOID VALVES P1203.45 Location: The dispense solenoids are located on the upper right side of the tank. Test Procedures: 1. Disconnect the dispenser from the power source. 2. Disconnect the whi[...]

  • Page 32

    32 SERVICE (cont.) SOLENOID VALVES (DISPENSE) (cont.) 3. Drain enough water from the tank so the water level is below the dispense valve mounting hole. NOTE: Bunn-O-Matic has a syphon assembly, #12440.0000. available for this purpose. 4. Disconnect the water line from the solenoid valve. 5. Remove the #10-32 screw securing the solenoid valve to sid[...]

  • Page 33

    33 SERVICE (cont.) SOLENOID VALVE (INLET) (cont.) If continuity is not present as described, replace the solenoid valve. 6. Check the solenoid valve for coil action. Connect the dispenser to the power source. Listen care- fully in the vicinity of the solenoid valve for a "clicking" sound as the coil magnet attracts. 7. Disconnect the disp[...]

  • Page 34

    34 P1199.35 SERVICE (cont.) TANK HEATER (cont.) 5. Check for continuity across the tank heater termi- nals. If continuity is present as described, reconnect the wires, the tank heater is operating properly. If continuity is not present as described, replace the tank heater. NOTE - If the tank heater remains unable to heat, remove and inspect heater[...]

  • Page 35

    35 SERVICE (cont.) Test Procedure: 1. Disconnect the dispenser from the power source. 2. Disconnect the black wire and the blue/black wire on electro/mechanical thermostats or the tan wires on electronic thermostats. 3. With the switch in the “ ON ” lower position check for continuity between the center and the upper terminal. With the switch i[...]

  • Page 36

    36 TRANSFORMER (240V TWO WIRE MODELSONLY)(cont.) 1 2 3 FIG.34 TRANSFORMER TERMINALS P1288 BLK & WHI to Fan RED & BLK to Main Harness SERVICE (cont.) Removal and Replacement: 1. Disconnect the wires from the transformer. 2. Remove the two #8-32 keps nuts securing the transformer to the dispenser base. 3. Remove and discard the transformer. 4[...]

  • Page 37

    37 BLK RED/WHI SOL DISPENSE M WHIPPER M HOPPER RUN/RINSE SWITCH WHI/GRN WHI WHI/BLK WHI WHI WHI/RED WHI/RED WHI WHI/RED SOL LEFT DISPENSE M RIGHT WHIPPER M RIGHT HOPPER SOL RIGHT DISPENSE M LEFT WHIPPER M LEFT HOPPER M CENTER HOPPER M CENTER WHIPPER SOL CENTER DISPENSE WHI/GRN WHI/GRN WHI WHI/BLK WHI/BLK WHI/BLK WHI/VIO WHI/VIO WHI/VIO WHI WHI WHI [...]

  • Page 38

    38 WHI BLK BLK BLU BLU RED/WHI SOL DISPENSE M WHIPPER M HOPPER RUN/RINSE SWITCH WHI/GRN WHI WHI/BLK WHI WHI WHI/RED WHI/RED WHI WHI/RED SOL LEFT DISPENSE M RIGHT WHIPPER M RIGHT HOPPER SOL RIGHT DISPENSE M LEFT WHIPPER M LEFT HOPPER M CENTER HOPPER M CENTER WHIPPER SOL CENTER DISPENSE WHI/GRN WHI/GRN WHI WHI/BLK WHI/BLK WHI/BLK WHI/VIO WHI/VIO WHI/[...]