Toshiba 960-498 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365

Ir a la página of

Buen manual de instrucciones

Las leyes obligan al vendedor a entregarle al comprador, junto con el producto, el manual de instrucciones Toshiba 960-498. La falta del manual o facilitar información incorrecta al consumidor constituyen una base de reclamación por no estar de acuerdo el producto con el contrato. Según la ley, está permitido adjuntar un manual de otra forma que no sea en papel, lo cual últimamente es bastante común y los fabricantes nos facilitan un manual gráfico, su versión electrónica Toshiba 960-498 o vídeos de instrucciones para usuarios. La condición es que tenga una forma legible y entendible.

¿Qué es un manual de instrucciones?

El nombre proviene de la palabra latina “instructio”, es decir, ordenar. Por lo tanto, en un manual Toshiba 960-498 se puede encontrar la descripción de las etapas de actuación. El propósito de un manual es enseñar, facilitar el encendido o el uso de un dispositivo o la realización de acciones concretas. Un manual de instrucciones también es una fuente de información acerca de un objeto o un servicio, es una pista.

Desafortunadamente pocos usuarios destinan su tiempo a leer manuales Toshiba 960-498, sin embargo, un buen manual nos permite, no solo conocer una cantidad de funcionalidades adicionales del dispositivo comprado, sino también evitar la mayoría de fallos.

Entonces, ¿qué debe contener el manual de instrucciones perfecto?

Sobre todo, un manual de instrucciones Toshiba 960-498 debe contener:
- información acerca de las especificaciones técnicas del dispositivo Toshiba 960-498
- nombre de fabricante y año de fabricación del dispositivo Toshiba 960-498
- condiciones de uso, configuración y mantenimiento del dispositivo Toshiba 960-498
- marcas de seguridad y certificados que confirmen su concordancia con determinadas normativas

¿Por qué no leemos los manuales de instrucciones?

Normalmente es por la falta de tiempo y seguridad acerca de las funcionalidades determinadas de los dispositivos comprados. Desafortunadamente la conexión y el encendido de Toshiba 960-498 no es suficiente. El manual de instrucciones siempre contiene una serie de indicaciones acerca de determinadas funcionalidades, normas de seguridad, consejos de mantenimiento (incluso qué productos usar), fallos eventuales de Toshiba 960-498 y maneras de solucionar los problemas que puedan ocurrir durante su uso. Al final, en un manual se pueden encontrar los detalles de servicio técnico Toshiba en caso de que las soluciones propuestas no hayan funcionado. Actualmente gozan de éxito manuales de instrucciones en forma de animaciones interesantes o vídeo manuales que llegan al usuario mucho mejor que en forma de un folleto. Este tipo de manual ayuda a que el usuario vea el vídeo entero sin saltarse las especificaciones y las descripciones técnicas complicadas de Toshiba 960-498, como se suele hacer teniendo una versión en papel.

¿Por qué vale la pena leer los manuales de instrucciones?

Sobre todo es en ellos donde encontraremos las respuestas acerca de la construcción, las posibilidades del dispositivo Toshiba 960-498, el uso de determinados accesorios y una serie de informaciones que permiten aprovechar completamente sus funciones y comodidades.

Tras una compra exitosa de un equipo o un dispositivo, vale la pena dedicar un momento para familiarizarse con cada parte del manual Toshiba 960-498. Actualmente se preparan y traducen con dedicación, para que no solo sean comprensibles para los usuarios, sino que también cumplan su función básica de información y ayuda.

Índice de manuales de instrucciones

  • Página 1

    1 Toshiba Personal Computer QOSMIO F10 Maintenance Manual TOSHIBA CORPORATION File Number 960-498[...]

  • Página 2

    Copyright © 2004 by Toshiba Corporation. All rights reserved. Under the cop yright laws, this manual cannot be reproduced in any form without the prior written permissi on of Toshiba. No patent liability is assumed with respect to the use of the in formation contai ned herein. Toshiba QOSMIO F10 Mai ntenance Man ual First edition October 2004 Disc[...]

  • Página 3

    Preface This maintenance manual describes how to pe rform hardware service maintenance for the Toshiba Personal Computer QOSMIO F10. NOTE: Each model of QOSMIO F10 has a diff erent configuration. For each model’s configuration, refer to the parts list dedicated to it. The procedures described in this manual are intended to help service technician[...]

  • Página 4

    The manual is divided into the following parts: Chapter 1 Hardware Overview describes the QOSMIO F10 system unit and each FRU. Chapter 2 Troubleshooting Procedures e xplains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service. Chapter 4 Replacement [...]

  • Página 5

    Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronym s are enclosed in parentheses following their definition. For example: Read Only Memory (ROM) Keys Keys are used in the text to describe many operat[...]

  • Página 6

    Table of Contents Chapter 1 Hardware Overview 1.1 Features ................................................................................................................... ... 1-1 1.2 System Block Diagram .............................................................................................. 1-5 1.3 2.5-inch Hard Disk Drive ..............[...]

  • Página 7

    Chapter 3 Tests and Diagnostics 3.1 The Diagnostic Test ................................................................................................... 3-1 3.2 Executing the Diagnostic Test ................................................................................... 3-4 3.3 Setting of the hardware configuration...........................[...]

  • Página 8

    Chapter 4 Replacement Procedures 4.1 Overview ................................................................................................................... .4 - 1 4.2 Battery pack/PC card/Bridge Media .......................................................................... 4-8 4.3 HDD ........................................................[...]

  • Página 9

    Appendices Appendix A Handling the LCD Module ........................................................................ A-1 Appendix B Board Layout ............................................................................................. B-1 Appendix C Pin Assignment ...............................................................................[...]

  • Página 10

    x QOSMIO F 10 Mainte nance Manu al (960- 498)[...]

  • Página 11

    Chapter 1 Hardware Overview[...]

  • Página 12

    1 Hardware Overview 1 Hardware Overview 1-ii QOSMIO F 10 Maint enance Ma nual (960 -498)[...]

  • Página 13

    1 Hardware Overview Chapter 1 Contents 1.1 Features ................................................................................................................... ... 1-1 1.2 System Block Diagram .............................................................................................. 1-5 1.3 2.5-inch Hard Disk Drive .....................[...]

  • Página 14

    1 Hardware Overview 1-iv QOSMIO F 10 Maint enance Ma nual (960 -498) Figures Figure 1-1 Front of the computer and the system units configuration ............................ 1-4 Figure 1-2 System block diagram .................................................................................... 1-5 Figure 1-3 2.5-inch HDD ...........................[...]

  • Página 15

    1 Hardware Overview 1.1 Features 1 Features 1.1 Features The QOSMIO F10 series are high performan ce all-in-one PCs running a Pentium-M processor. The features are listed below. ❑ Microprocessor Microprocessor that is used depends on the model. Mobile Intel ® Pentium ® -M Pentium-M 1.50GHz (Processor Number ; 715) 1.60GHz (Processor Number ; 72[...]

  • Página 16

    1.1 Features 1 Hardware Overview ❑ Display LCD Built-in 15.4-inch, XGA (1,280 x 800 dots), 262,144 colors, amorphous silicon TFT color display. Clear Super View LCD. CRT Supported via a RGB connector. TV-out S-VIDEO/Composite out port is su pported. (Supporting NTSC, PAL and SECAM) D-VIDEO out port is supported. ❑ Monitor-IN port This port can [...]

  • Página 17

    1 Hardware Overview 1.1 Features ❑ Battery The RTC battery is mounted inside the computer. The main battery is a de tachable lithium ion battery (4,400mAh:Li-Ion, 6-cell). ❑ USB (Universal Serial Bus) Four USB ports are provided. The ports comply with the USB2.0 standard, which enables data transfer speeds 40 times fast er than USB1.1 standard.[...]

  • Página 18

    1.1 Features 1 Hardware Overview Figure 1-1 shows the front of the comput er and the system units configuration. Figure 1-1 Front of the computer an d the system units configuration 1-4 QOSMIO F 10 Maint enance Ma nual (960 -498)[...]

  • Página 19

    1 Hardware Overview 1.2 System Block Diagram 1.2 System Block Diagram Figure 1-2 shows the system block diagram. Figure 1-2 System block diagram QOSMIO F 10 Maint enance Ma nual (960 -498) 1-5[...]

  • Página 20

    1.2 System Block Diagram 1 Hardware Overview The PC contains the following components. ❑ CPU Mobile Intel ® Pentium ® -M Pentium-M 1.50GHz (Processor Number ; 715) 1.60GHz (Processor Number ; 725) 1.70GHz (Processor Number ; 735) 1.80GHz (Processor Number ; 745) 2.00GHz (Processor Number ; 755) 2.10GHz (Processor Number ; 765) L1 cache : 64KB ([...]

  • Página 21

    1 Hardware Overview 1.2 System Block Diagram ❑ Chipset This gate array has the following elements and functions. • North Bridge (Intel 855PME (MCH-M, B-step)) − Pentium-M processor System Bus support − DRAM Controller : DDR 333/DDR266/DDR200 support − AGP Interface (AGP R2.0, AGP x 4 modes) − Hub Link Interface − 593-ball 37.5mmx37.5m[...]

  • Página 22

    1.2 System Block Diagram 1 Hardware Overview ❑ VGA controller • nVIDIA NV36M − VRAM 64MB/128MB − AGP 4x (32bit) − TMDS − TV Encoder ❑ Super I/O (SMSC-made LPC47N217) • Two serial ports (NS16C550 compatible) (1 port is used as Debug port) ❑ Other main system chips • PSC (Toshiba-made TMP87PM48U x 1) • Clock Generator (ICS-made [...]

  • Página 23

    1 Hardware Overview 1.2 System Block Diagram ❑ LAN (Intel-made ED82562 (Kinnereth) x 1) Controls LAN. Supports 100Base-TX and 10Base-T. ❑ MODEM (Askey-made 1456VQL4 x 1) Supported by MDC. Uses secondary AC97 line. Data and FAX transmission is available. Supports ITU-TV.90 or .92. The transfer speed of data receiving is 56kbps, of data sending i[...]

  • Página 24

    1.3 2.5-inch Hard Disk Drive 1 Hardware Overview 1.3 2.5-inch Hard Disk Drive A compact, high-capacity HDD with a height of 9.5mm. Contains a 2.5-inch magnetic disk and magnetic heads. Figure 1-3 shows a view of the 2.5-inch HDD and Tables 1-1 and 1-2 list the specifications. Figure 1-3 2.5-inch HDD Table 1-1 2.5-inch HDD dimensions (1/2) Standard [...]

  • Página 25

    1 Hardware Overview 1.3 2.5-inch Hard Disk Drive Table 1-1 2.5-inch HDD dimensions (2/2) Standard value Parameter FUJITSU G8BC00019610 FUJITSU G8BC000 1C610 FUJITSU G8BC000 1HA10 Width (mm) 70 Outline Height (mm) 9.5 dimensions Depth (mm) 100.0 Weight (g) 99 (MAX) QOSMIO F 10 Maint enance Ma nual (960 -498) 1-11[...]

  • Página 26

    1.3 2.5-inch Hard Disk Drive 1 Hardware Overview Table 1-2 2.5-inch HDD specifications (1/2) Specification (TOSHIBA) Parameter HDD2189B HDD2194 B HDD2188 B HDD2191V HDD2A02B HDD2D08B Storage size (formatted) 60GB 80GB 100GB Speed (RPM) 4,200 5,400 4,200 5,400 4,200 5,400 Data transfer speed (Mbits/s) 175.0- 341.7 258.0- 394.0 175.0- 341.7 154.3- 29[...]

  • Página 27

    1 Hardware Overview 1.3 2.5-inch Hard Disk Drive Table 1-2 2.5-inch HDD specifications (2/2) Specification (FUJITSU) Parameter G8BC00019610 G8BC0001 C610 G8BC00 01HA10 Storage size (formatted) 60GB 100GB Speed (RPM) 4,200 5,400 4,200 Data transfer speed (Mbits/s) 330.4 554 443.2 Interface transfer rate (MB/s) 100 (Ultra DMA mode) Storage density (K[...]

  • Página 28

    1.4 Optical Drive 1 Hardware Overview 1.4 Optical Drive This model equipped with the DVD super multi dr ive as the optical drive. Som e drives support double layer specification. The DVD Super Multi drive accommodates either 12 cm (4.72-inch) or 8 cm (3.15-inch) CD, CD-R/RW and DVD. It is a high-performan ce drive that reads DVD-ROM at maximum 8- s[...]

  • Página 29

    1 Hardware Overview 1.4 Optical Drive Table 1-4 DVD Super Multi drive specifications (1/4) Drive Specification Parameter MATSUSHITA (G8CC0001S610 ) Read(KB/s) DVD-ROM MAX 8X CAV CD-ROM MAX 24X CAV Write CD-R 16x (Zone CLV) CD-RW 4X (CLV) High Speed CD-RW 8X (CLV) DVD-R 4x (Zone CLV) DVD-RW 2x (CLV) DVD+R 2.4x (CLV) DVD+RW 2.4x (CLV) DVD-RAM 2x (ZCL[...]

  • Página 30

    1.4 Optical Drive 1 Hardware Overview Table 1-4 DVD Super Multi drive specifications (2/4) Drive Specification Parameter Matsushita (G8CC00021610) Read(KB/s) DVD-ROM MAX 8X CAV CD-ROM MAX 24X CAV Write CD-R MAX 24x (Zone CLV) CD-RW 4X (CLV) HSRW MAX 10X (CLV) USRW 10X (CLV) DVD-R MAX 8x (Zone CLV) DVD-RW MAX 4x (Zone CLV) DVD+R MAX 8x (Zone CLV) DV[...]

  • Página 31

    1 Hardware Overview 1.4 Optical Drive Table 1-4 DVD Super Multi drive specifications (3/4) Drive Specification Parameter Matsushita (G8CC00021611) Supporting Double Layer Read(KB/s) DVD-ROM MAX 8X CAV CD-ROM MAX 24X CAV Write CD-R MAX 24x (Zone CLV) CD-RW 4X (CLV) HSRW MAX 10X (CLV) USRW 10X (CLV) DVD-R MAX 8x (Zone CLV) DVD-RW MAX 4x (Zone CLV) DV[...]

  • Página 32

    1.4 Optical Drive 1 Hardware Overview Table 1-4 DVD Super Multi drive specifications (4/4) Drive Specification Parameter TEAC (G8CC00024611) Supporting Double Layer Read(KB/s) DVD-ROM MAX 8X CAV CD-ROM MAX 24X CAV Write CD-R MAX 24x (Zone CLV) CD-RW 4X (CLV) HSRW MAX 10X (CLV) USRW 10X (CLV) DVD-R MAX 8x (Zone CLV) DVD-RW MAX 4x (Zone CLV) DVD+R MA[...]

  • Página 33

    1 Hardware Overview 1.5 Keyboard 1.5 Keyboard A keyboard which consists of 85(US)/86(UK) keys is mounted on the system unit. The keyboard is connected to membrane connector on the system board and controlled by the keyboard controller. Figure 1-5 is a view of the keyboard. Figure 1-5 Keyboard See Appendix E for details of the keyboard layout. QOSMI[...]

  • Página 34

    1.6 TFT Color Display 1 Hardware Overview 1.6 TFT Color Display The TFT color display is 15.4 inch and consists of LCD module and FL inverter boards. 1.6.1 LCD Modu le The LCD module used for the TFT color display uses two backlights as the light source and can display a maximum of 262,144 colo rs with 1,280 x 800 resolution. Figure 1-6 shows a vie[...]

  • Página 35

    1 Hardware Overview 1.6 TFT Color Display 1.6.2 FL Inverter Board The FL inverter board supplies a high freque ncy current to illuminate the LCD module FL. Table 1-6 lists the FL inve rter board specifications. Table 1-6 FL inverter board specifications Specifications Item G71C0004F310 Voltage (V) 5 (DC) Input Power (W) 18 Output Voltage (V) 900 (r[...]

  • Página 36

    1.7 Power Supply 1 Hardware Overview 1.7 Power Supply The power supply supplies twenty-five di fferent voltages to the system board. The power supply microcontroller has the following functions. 1. Judges if the DC power supply (AC adap ter) is connected to the computer. 2. Detects DC output and circuit malfunctions. 3. Controls the battery icon, a[...]

  • Página 37

    1 Hardware Overview 1.7 Power Supply Table 1-7 Power suppl y output rating (2/2) Power supplied ( Yes/No ) Name Voltage [V] Power OFF Suspend mode Power OFF Boot mode No Battery Use USB0PS-E5V 5 Yes No No USB USB1PS-E5V 5 Yes No No USB SND-P5V 5 No No No AN12941 A4R7-P4V 4.7 No No No AD1981B, AN12941 MCV 5 Yes Yes No PSC P3V 3.3 No No No Clock [...]

  • Página 38

    1.8 Batteries 1 Hardware Overview 1.8 Batteries The PC has the following two batteries. ❑ Main battery ❑ Real time clock (RTC) battery Table 1-8 lists the specifications for these two batteries. Table 1-8 Battery specifications Battery Name Battery Element Output Voltage Capacity G71C0004H210 G71C0004H610 G71C0004H110 Main battery G71C0004H510 [...]

  • Página 39

    1 Hardware Overview 1.8 Batteries 1.8.2 Battery Charging Control Battery charging is controlled by a power supply microprocessor. The power supply microprocessor controls power supply and dete cts a full charge when the AC adaptor and battery are connected to the computer. ❑ Battery Charge When the AC adapter is connected, normal charging is used[...]

  • Página 40

    1.8 Batteries 1 Hardware Overview 1.8.3 RTC Batter y The RTC battery provides the power supply to maintain the date, time, and other system information in memory. Table 1-11 lists the Time required for charges of RTC battery and data preservation time. Table 1-11 Time required fo r charges of RTC battery Condition Time Power ON (Lights Power LED) M[...]

  • Página 41

    1 Hardware Overview 1.9 AC Adapter 1.9 AC Adapter The AC adapter is used to charge the battery. Table 1-12 lists the AC adapter specifications. Table 1-12 AC adapter specifications Parameter Specification (G71C00024410) Power 90W (Peak 105W) Input voltage AC 100 to 240V Input frequency 50Hz/60Hz Input voltage 1.3A or less Output voltage DC 15V Outp[...]

  • Página 42

    1.9 AC Adapter 1 Hardware Overview 1-28 QOSMIO F 10 Maint enance Ma nual (960 -498)[...]

  • Página 43

    Chapter 2 Troubleshooting Procedures[...]

  • Página 44

    2 Troubleshooting Procedures 2 2-ii QOSMIO F 10 Maint enance Ma nual (960 -498)[...]

  • Página 45

    2 Troubleshooting Procedures Chapter 2 Contents 2.1 Troubleshooting ......................................................................................................... 2-1 2.2 Troubleshooting Flowchart ........................................................................................ 2-2 2.3 Power Supply Troubleshooting.................[...]

  • Página 46

    2 Troubleshooting Procedures 2.9 Display Troubleshooting .......................................................................................... 2-47 Procedure 1 External Monitor Check ....................................................... 2-47 Procedure 2 Diagnostic Test Program Execution Check ......................... 2-47 Procedure 3 Connec[...]

  • Página 47

    2 Troubleshooting Procedures Figures Figure 2-1 Troubleshooting flowchart ............................................................................. 2-3 Figure 2-2 A set of tool for debug port test ................................................................... 2-19 Tables Table 2-1 Battery icon ..............................................[...]

  • Página 48

    2 Troubleshooting Procedures 2-vi QOSMIO F 10 Mainten ance Manu al (960- 498)[...]

  • Página 49

    2 Troubleshooting Procedures 2.1 Troubleshooting 2 2.1 Troubleshooting Chapter 2 describes how to determine which Fi eld Replaceable Unit (FRU) in the computer is causing the computer to malfunction. (The “FRU ” m eans the replaceable unit in the field.) The FRUs covered are: 1. Power supply 6. Touch pad 11. Wireless LAN 2. System Board 7. Disp[...]

  • Página 50

    2.2 Troubleshooting Flowchart 2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart Use the flowchart in Figure 2-1 as a guide fo r determining which troubleshooting procedures to execute. Before going through the fl owchart steps, verify the following:  Ask the user if a password is registered and, if it is, ask him or her to enter the pas[...]

  • Página 51

    2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart Figure 2-1 Troubleshooting flowchart (1/2) QOSMIO F 10 Maint enance Ma nual (960 -498) 2-3[...]

  • Página 52

    2.2 Troubleshooting Flowchart 2 Troubleshooting Procedures Figure 2-1 Troubleshooting flowchart (2/2) 2-4 QOSMIO F 10 Maint enance Ma nual (960 -498)[...]

  • Página 53

    2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart If the diagnostics program cannot detect an e rror, the problem may be intermittent. The Test program should be executed several tim es to is olate the problem. Check the Log Utilities function to confirm which diagnos tic test detected an error(s), and perf orm the appropriate troubleshoot[...]

  • Página 54

    2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting The power supply controller cont rols many functions and compone nts. To determine if the power supply is functioning properly, start with Procedure 1 and continue with the other Procedures as instructed. The procedur es described in this section are: Pro[...]

  • Página 55

    2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting Table 2-2 DC IN icon DC IN icon Power supply status Lights green DC power is being supplie d from the AC adapter. Blinks orange Power supply malfunctio n *1 Doesn’t light Any condition other than those above. *1 When the power supply controller det ects a malfunction, the DC IN icon bl[...]

  • Página 56

    2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Procedure 2 Error Code Check If the power supply microprocessor detects a ma lfunction, the DC IN icon blinks orange. The blink pattern indicates an error as shown below.  Start Off for 2 seconds  Error code (8 bit) “1” On for one second “0” On for half second Interval betw[...]

  • Página 57

    2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting Table 2-3 Error code Error code Where error occurs 1*h DC Power (AC Adapte r) 2*h Main battery 3:h 2nd batte ry 4*h S3V output 5*h 1R5-C1V output (P61) 6*h 1R5-C1V output (P62) 7*h PPV output 8*h PTV output 9*h E5V output A*h E3V output B*h 2R5-P2V output C*h PGV output D*h 1R25-B1V outp[...]

  • Página 58

    2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures  Main Battery Error code Meaning 21h Main battery charge curre nt is over 12.0A. 22h Main battery discharge cu rrent is over 0.5A when there is no load. 23h Main battery charge curre nt is over 3.9A when AC adapter is not connected. 24h Abnormal current has been sen sed. 25h Main batt[...]

  • Página 59

    2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting  1R5-C1V output Error code Meaning 60h 1R5-C1V voltage is over 2.16V wh en the computer is powered on/off. 61h 1R5-C1V voltage is 1.275V or less when the computer is powered on. 62h 1R5-C1V voltage is 1.275V or less when the computer is booting up. 63h 1R5-C1V voltage is 1.275V or les[...]

  • Página 60

    2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures  E3V output Error code Meaning A0h E3V voltage is over 3.96V when the computer is powered on/off. A1h E3V voltage is 2.81V or less when the computer is powered o n. A2h E3V voltage is 2.81V or less when the computer is booting up. A3h E3V voltage is 2.81V or more wh en the computer is[...]

  • Página 61

    2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting  2R5-B2V output Error code Meaning E0h 2R5-B2V voltage is over 3. 00V when the computer is powered on/off. E1h 2R5-B2V voltage is 2.1 25V or less when the computer is powered on. E2h 2R5-B2V voltage is 2.1 25V or less when the computer is booting up . E3h 2R5-B2V voltage is 2.125V or [...]

  • Página 62

    2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures Procedure 3 Connection Check The wiring diagram related to th e power supply is shown below: Any of the connectors may be disconnected. Perform Check 1. Check 1 Make sure the AC adapter and the AC power cord are firmly plugged into the DC IN 15 V socket and wall outlet. If these cables a[...]

  • Página 63

    2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting Procedure 5 Replacement Check The power is supplied to the system board by the AC adapter. If either the AC adapter or the system board was damaged, perform the following Checks. To disassemble the computer, follow the steps described in Chapter 4, Replacement Procedures . Check 1 Replac[...]

  • Página 64

    2.4 System Board Troubleshooting 2 Troubleshooting Procedures 2.4 System Board Troubleshooting This section describes how to determine if the sy stem board is defective. Start with Procedure 1 and continue with the other pr ocedures as instructed. The procedures described in this section are: Procedure 1: Message Check Procedure 2: Debug Port Check[...]

  • Página 65

    2 Troubleshooting Procedures 2.4 System Board Troubleshooting Procedure 1 Message Check When the power is turned on, the system perfor ms the Initial Reliability T est (IRT) installed in the BIOS ROM. The IRT tests each IC on the system board and initializes it.  If an error message is shown on the display, perform Check 1.  If there is no er[...]

  • Página 66

    2.4 System Board Troubleshooting 2 Troubleshooting Procedures If any other error message displays, perform Check 3. Check 3 The IRT checks the system board. When the IRT detects an erro r, the system stops or an error message appears. If one of the following error messages (1) th rough (17), (22) or (23) is displayed, go to Procedure 4. If error me[...]

  • Página 67

    2 Troubleshooting Procedures 2.4 System Board Troubleshooting Procedure 2 Debug Port Check Check the D port status by a debug port test. Th e tool for debug port test is shown below. Figure 2-2 A set of to ol for debug port test The test procedures are follows: 1. Connect the debug test cable to the c onnector CN3400 of the system board. For disass[...]

  • Página 68

    2.4 System Board Troubleshooting 2 Troubleshooting Procedures Table 2-4 Debug port (Boot mode) error status (1/9) D port status Inspection items Details Permission of A20 and Cl ear of software reset bit Prohibition of APIC Initialization of MCHM, ICHM Initialization of Super I/O Initialization of debug port Dummy read of 3 rd Bus data Setting of p[...]

  • Página 69

    2 Troubleshooting Procedures 2.4 System Board Troubleshooting Table 2-4 Debug port (Boot mode) error status (2/9) D port status Inspection items Details F004h/F005h Saving key scan code Setting TASK_1ms_TSC Controlling fan Enabling system spea ker Releasing mute Initializing sound items (for BEEP) Making the volume max. (for models whose volume can[...]

  • Página 70

    2.4 System Board Troubleshooting 2 Troubleshooting Procedures Table 2-4 Debug port (Boot mode) error status (3/9) D port status Inspection items Details Initialization of MCHM Initialization of ICH4M.D31.Func0 Initialization of ICH4M.D31.Func1 Initialization of USB.Func0,1,2,7 Initialization of ICH4M.D31.Func3 Initialization of ICH4M.D31.Func5 Init[...]

  • Página 71

    2 Troubleshooting Procedures 2.4 System Board Troubleshooting Table 2-4 Debug port (Boot mode) error status (4/9) D port status Inspection items Details (F103h) Resume error check S3 recovery error (I CH) Resume error F17AH SM-RAM checksum check Resume error F173H Memory configuration change check Resume error F173H Checksum check of system BIOS RA[...]

  • Página 72

    2.4 System Board Troubleshooting 2 Troubleshooting Procedures Table 2-4 Debug port (Boot mode) error status (5/9) D port status Inspection items Details (F105h) CPU clock measurement Check of parameter block A Permi ssion of SMI except auto-off function Cont rol of excess of rated input powe r Battery discharge current cont rol (1CmA) AC adapter ra[...]

  • Página 73

    2 Troubleshooting Procedures 2.4 System Board Troubleshooting Table 2-4 Debug port (Boot mode) error status (6/9) D port status In spection items Details PCI bus initialization (connection of DS Bus) Initialization of LAN information F107h Check of Wake Up factor Task generation for waiting INIT_PCI completion CMOS data initialization (2) PnP initi[...]

  • Página 74

    2.4 System Board Troubleshooting 2 Troubleshooting Procedures Table 2-4 Debug port (Boot mode) error status (7/9) D port status Inspection items Details F10Dh INIT_NDP (Initializ ation of NDP) Storing of CMOS error status to IRT_ERR_STS_BUF CD POWER SW control (for models supporting CD Play function ) Timer initialization start EC initialization &a[...]

  • Página 75

    2 Troubleshooting Procedures 2.4 System Board Troubleshooting Table 2-4 Debug port (Boot mode) error status (8/9) D port status Inspection items Details (F11Ch) (In the case of “Boot”) BM loading process (for m odels support ing fingerprint authentication) Initialization of BM (for models suppo rting fingerprint authentication) Check of key inp[...]

  • Página 76

    2.4 System Board Troubleshooting 2 Troubleshooting Procedures Table 2-4 Debug port (Boot mode) error status (9/9) D port status Inspection items Details Initialization of Bluetooth (for models supp orting Bluetooth) Check of existence of target maintenanc e card Prohibition of unused PC card Setting Wakeup status data for ACPI (F11Eh) HW initializa[...]

  • Página 77

    2 Troubleshooting Procedures 2.4 System Board Troubleshooting Table 2-5 Debug port (Suspend mode) error status (1/3) D port status Inspection items Details Sets the parallel port to D0 state (for models supporting printer) F12Fh Release resources used for fin gerprint authentication. (For models supporting fingerprint authentication) When powering-[...]

  • Página 78

    2.4 System Board Troubleshooting 2 Troubleshooting Procedures Table 2-5 Debug port (Suspend mode) error status (2/3) LED Status Test item Contents Storing CPU register Permission of system area and memory cache (for high-speed operati on) Suspending of HDD Storing KBC,SCC and MOUSE Storing of PCI device Storing of PIT Starts sequence for storing di[...]

  • Página 79

    2 Troubleshooting Procedures 2.4 System Board Troubleshooting Table 2-5 Debug port (Suspend mode) error status (3/3) LED Status Test item Contents (F13Ah) Power LED control during suspendin g Isolates built-in LAN Makes the power of sound off Makes the power of Dock off (for models supporting Dock) F13Bh Model-unique processing jus t before suspend[...]

  • Página 80

    2.4 System Board Troubleshooting 2 Troubleshooting Procedures Table 2-6 Debug port (Resume mode) error status (1/4) LED Status Test item Contents F100h Refer to IRT F101h Refer to IRT F102h Refer to IRT Refer to IRT Clears flag for SMI control. F103h Update of Resume counter Checks the WakeUp factors. F121h Rewriting of SMRAM BASE I/O LOCK processi[...]

  • Página 81

    2 Troubleshooting Procedures 2.4 System Board Troubleshooting Table 2-6 Debug port (Resume mode) error status (2/4) LED Status Test item Contents (F122h) AC'97 control Initializing of temperature cont rol information Initializing of KBC VGA display-off and Reset control Initialization of devices necessar y for initialization before initi alizi[...]

  • Página 82

    2.4 System Board Troubleshooting 2 Troubleshooting Procedures Table 2-6 Debug port (Resume mode) error status s (3/4) LED status Test item Con tents Recovery of user alarm setting and cancel of alarm power-on function (on ly one time) Enable of power-off switch F125h Initializing EC and start of reading battery information Recovery of each device(2[...]

  • Página 83

    2 Troubleshooting Procedures 2.4 System Board Troubleshooting Table 2-6 Debug port (Resume mode) error status (4/4) LED status Test item Con tents (F12Ah) Process related to CPU Setting of CPU clock to SETUP designation Waiting for motor-off of disabled HDD Final decision of USB FDD information Post-process of PRE_BOOT_SETUP Clears PWRBTN_STS. Enab[...]

  • Página 84

    2.4 System Board Troubleshooting 2 Troubleshooting Procedures 2-36 QOSMIO F 10 Maint enance Ma nual (960 -498) Procedure 3 Diagnostic Test Program Execution Check Execute the following tests from the Diagnostic Test Menu. These tests check the system board. Refer to Chapter 3, Tests and Diagnostic, for more information on how to perform these tests[...]

  • Página 85

    2 Troubleshooting Procedures 2.5 USB 3.5” FDD Troubleshooting 2 2.5 USB 3.5” FDD Troubleshooting This section describes how to determine if the USB 3.5” FDD is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: FDD Head Cleaning Check Procedure 2: Diagnost[...]

  • Página 86

    2.5 USB 3.5” FDD Troubleshooting 2 Troubleshooting Procedures Procedure 2 Diagnostic Test Program Execution Check Insert the Diagnostics Disk in the FDD connected to the computer, turn on the com puter and run the test. Refer to Chapter 3, Tests and Diagnostics, for more information about the diagnostics test procedures. Make sure the floppy disk[...]

  • Página 87

    2 Troubleshooting Procedures 2.5 USB 3.5” FDD Troubleshooting Procedure 3 Connector Check and Replacement Check The USB FDD connector may be disconnected from the system board or SD board. Check visually that the connector is c onnected to one of them firmly. Check 1 Make sure the following cables and conn ectors are firmly connected to the syste[...]

  • Página 88

    2.6 2.5” HDD Troubleshooting 2 Troubleshooting Procedures 2.6 2.5” HDD Troubleshooting This section describes how to determine if the 2.5” HDD is functioning properly. Perform the steps below starting with Procedure 1 and con tinuing with the other pr ocedures as required. Procedure 1: Partition Check Procedure 2: Message Check Procedure 3: F[...]

  • Página 89

    2 Troubleshooting Procedures 2.6 2.5” HDD Troubleshooting Procedure 2 Message Check When the power is turned on, the system perfor ms the Initial Reliability T est (IRT) installed in the BIOS ROM. When the test detects an erro r, an error message is displayed on the screen. Turn on the computer and check the message on th e screen. When an OS sta[...]

  • Página 90

    2.6 2.5” HDD Troubleshooting 2 Troubleshooting Procedures Procedure 3 Format Check The computer’s HDD is formatted using the MS-DOS FORMAT program or the physical format program of the test program. To fo rmat the HDD, start with Check 1 below and perform the other steps as required. Refer to the MS-DOS Manual for the operation of MS-DOS. For t[...]

  • Página 91

    2 Troubleshooting Procedures 2.6 2.5” HDD Troubleshooting Procedure 4 Diagnostic Test Program Execution Check The HDD test program is stored in the Diagnosti cs Disk. Perform all of the HDD tests in the Hard Disk Drive Test. Refer to Chapter 3, Tests and Diagnostics, for more information about the HDD test program. If an error is detected during [...]

  • Página 92

    2.6 2.5” HDD Troubleshooting 2 Troubleshooting Procedures Procedure 5 Connector Check and Replacement Check The HDD is connected to the connector of th e system board. The connecting portion may be disconnected. Disassemble the computer fo llowing the steps described in Chapter 4, Replacement Procedures and perform the following checks to check t[...]

  • Página 93

    2 Troubleshooting Procedures 2.7 Keyboard Troubleshooting 2.7 Keyboard Troubleshooting To determine if the computer’s keyboard is functioning properly, perform the following procedures. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector Check an[...]

  • Página 94

    2.8 Touch Pad Troubleshooting 2 Troubleshooting Procedures 2.8 Touch Pad Troubleshooting To determine if the computer’s touch pad is functioning properly, perform the following procedures. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector Check[...]

  • Página 95

    2 Troubleshooting Procedures 2.9 Display Troubleshooting 2.9 Display Troubleshooting This section describes how to determine if the computer’s display is functioning properly. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: External Monitor Check Procedure 2: Diagnostic Te st Program Execution Check Proce[...]

  • Página 96

    2.9 Display Troubleshooting 2 Troubleshooting Procedures Procedure 3 Connector Check and Cable Check The LCD module is connected to the system board by an LCD/FL cable. The FL inverter board is also connected to the system board by an LCD/FL cable. And the FL is connected to the FL inverter board by the HV cable. The conn ectors may be disconnected[...]

  • Página 97

    2 Troubleshooting Procedures 2.9 Display Troubleshooting Procedure 4 Replacement Check The FL lamp, FL inverter, LCD module, system board and LCD/FL cable are connected to display circuits. Any of these components may be dam aged. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassembl e the computer and then perform the f[...]

  • Página 98

    2.10 Optical Drive Troubleshooting 2 Troubleshooting Procedures 2.10 Optical Drive Troubleshooting To check if the optical drive is defective or not, follow the troubles hooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program [...]

  • Página 99

    2 Troubleshooting Procedures 2.11 Modem Troubleshooting 2.11 Modem Troubleshooting To check if the modem is defective or malf unctioning, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Ch[...]

  • Página 100

    2.11 Modem Troubleshooting 2 Troubleshooting Procedures Check 5 The cable between the SD board and sy stem board m ay be faulty. Replace it with a new one following the instructions in Chapter 4. If the problem still occur s, perform Check 6. Check 6 The system board may be faulty. Replace it with a new one following the instruction in Chapter 4. 2[...]

  • Página 101

    2 Troubleshooting Procedures 2.12 LAN Troubleshooting 2.12 LAN Troubleshooting To check if the computer’s LAN is defec tive or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execu[...]

  • Página 102

    2.13 Wireless LAN Troubleshooting 2 Troubleshooting Procedures 2.13 Wireless LAN Troubleshooting This section describes how to determine if the computer's W ireless LAN is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: Transmitting-Receiving Check Proce[...]

  • Página 103

    2 Troubleshooting Procedures 2.13 Wireless LAN Troubleshooting Procedure 2 Antennas' Connection Check The wireless LAN function-wiri ng diagram is shown below: Any of the connections may be disconnected. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and check the followings: Check 1 Make sure the[...]

  • Página 104

    2.13 Wireless LAN Troubleshooting 2 Troubleshooting Procedures Procedure 3 Replacement Check The wireless LAN board, wireless LAN antennas or the system board may be damaged. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then check the followings: Check 1 The wireless LAN board may be def ective[...]

  • Página 105

    2 Troubleshooting Procedures 2.14 Sound Troubleshooting 2.14 Sound Troubleshooting To check if the sound function is defective or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector Check Procedure 3: Replacement Check Procedure 1 Diagnostic Test Program Execut[...]

  • Página 106

    2.14 Sound Troubleshooting 2 Troubleshooting Procedures Procedure 3 Replacement Check Check 1 When the headphone does not work properly, it may be faulty. Replace it with a new one. If the problem stil l occurs, perform Check 5. Check 2 When the external microphone does not work properly, it may be faulty. Replace it with a new one. If the problem [...]

  • Página 107

    2 Troubleshooting Procedures 2.15 TV Tuner Troubleshooting 2.15 TV Tuner Troubleshooting To check if the TV tuner is defective or not, follow the troubl eshooting procedures below as instructed. Procedure 1: Connector Check and Replacement Check Procedure 1 Connector Check and Replacement Check The TV antenna, TV tuner module, SD board or System bo[...]

  • Página 108

    2.15 TV Tuner Troubleshooting 2 Troubleshooting Procedures 2-60 QOSMIO F10 Maintenance Ma nual (960- 498)[...]

  • Página 109

    Chapter 3 Tests and Diagnostics[...]

  • Página 110

    3-ii QOSMIO F10 Maintenance Manual (960-498)[...]

  • Página 111

    Chapter 3 Contents 3.1 The Diagnostic Test ................................................................................................... 3-1 3.1.1 Diagnostics menu ................................................................................. 3-1 3.1.2 H/W(Hardware) initial information setting tool................................... 3-3 3.[...]

  • Página 112

    3.21.2 Operations .......................................................................................... 3-47 3.22 Log Utilities ............................................................................................................. 3-48 3.22.1 Function Description ..........................................................................[...]

  • Página 113

    Tables Table 3-1 Subtest names............................................................................................... 3-12 Table 3-2 Error codes and error status names .............................................................. 3-35 Table 3-3 Hard disk controller status register contents ................................................ 3[...]

  • Página 114

    3-vi QOSMIO F10 Maintenance Manual (960-498)[...]

  • Página 115

    3 Tests and Diagnostics 3.1 The Diagnostic Test 3 3.1 The Diagnostic Test This chapter explains how to use the Diagnostic Test programs to test the functions of the computer’s hardware modules. The Diagnostics Program s are stored on some Diagnostic Disks. There are Service Program Modules (DIAGNOSTIC MENU) and the Test Program Modules (DIAGNOSTI[...]

  • Página 116

    3.1 The Diagnostic Test 3 Tests and Diagnostics  NDP TEST  EXPANSION TEST  CD-ROM/DVD-ROM TEST Other tests are:  Wireless LAN TEST (Wireless LAN TEST disk)  LAN/Modem/Bluetooth/IEEE1394 TEST (LAN/Modem/Bluetooth/IEEE1394 TEST disk)  Sound TEST (Sound TEST disk) You will need the following equipment to perform som e of the Diagnost[...]

  • Página 117

    3 Tests and Diagnostics 3.1 The Diagnostic Test 3.1.2 H/W (Hardware) initial information setting tool The H/W initial inform ation setting tool consists of the following programs.  Initial configuration  Region write  System configuration display  E2PROM test (MAC/GUID/DMI) You will need the following equipment to perform some of the pr[...]

  • Página 118

    3.2 Executing the Diagnostic Test 3 Tests and Diagnostics 3.2 Executing the Diagnostic Test To start the DIAGNOSTIC PROGRAM, follow these steps: 1. Insert the Diagnostics disk in the floppy disk drive. 2. Release the lock of the power switch and turn on the computer with pressing the F12 . Select the FDD in the display for selecting booting unit. T[...]

  • Página 119

    3 Tests and Diagnostics 3.2 Executing the Diagnostic Test NOTE : To exit the DIAGNOSTIC TEST MENU, press Esc . If a test program is in progress, press Ctrl + Break to exit the test program. If a test program is in progress, press Ctrl + C to stop the test program. Set the highlight bar to 1 , and press Enter . The following DIAGNOSTIC TEST MENU wil[...]

  • Página 120

    3.2 Executing the Diagnostic Test 3 Tests and Diagnostics Select the option you want to execute and press Enter . When you select 1- SYSTEM TEST , the following message will appear: SYSTEM TEST NAME XXXXXX xxxxxxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] ; test end [Ctrl]+[C] ; key stop SUB-TEST : XX PASS COUNT : XXXXX ERROR COUNT: XXXXX WRITE DATA : X[...]

  • Página 121

    3 Tests and Diagnostics 3.2 Executing the Diagnostic Test Selecting YES of ERROR STOP stops the test program when an error is found and displays the operation guide on the right side of the display screen as shown below: ERROR STATUS NAME [[ HALT OPERATION ]] 1: Test end 2: Continue 3: Retry These three selections have the following functions respe[...]

  • Página 122

    3.3 Setting of the hardware configuration 3 Tests and Diagnostics 3.3 Setting of the hardware configuration To execute this program, select 2-Repair initial config set in the startup menu, press Enter and follow the directions on the screen. The H/W initial inform ation setting tool consists of following subtests. Move the highlight bar to the subt[...]

  • Página 123

    3 Tests and Diagnostics 3.3 Setting of the hardware configuration • Setting of the HWSC • Setting of the UUID • Display of the DMI information (including UUID) • Setting of DVD region code (Yes/No) After completion of the above settings, H/W configuration & DMI information are appeared in order. Check the contents and press Enter . Subt[...]

  • Página 124

    3.3 Setting of the hardware configuration 3 Tests and Diagnostics Subtest 08 System configuration display This subtest displays the information of the system configuration. When the following message appears, confirm the contents and press Enter . Press [Enter] key For more details on the system configuration inform ation, refer to "3.25 Syste[...]

  • Página 125

    3 Tests and Diagnostics 3.4 Heatrun Test 3.4 Heatrun Test To execute this program, select 3-Repair heatrun in the startup menu and press Enter . After selecting this test, the same subtests as 3.23 Running Test are executed successively. For more details on the procedure and test content, refer to Running Test. When the heatrun test ends, following[...]

  • Página 126

    3.5 Subtest Names 3 Tests and Diagnostics 3.5 Subtest Names Table 3-1 lists the subtest names for each test program in the DIAGNOSTIC TEST MENU. Table 3-1 Subtest names (1/2) No. Test Name Subtest No. Subtest Name 1 SYSTEM 01 02 03 04 05 ROM checksum Fan ON/OFF Geyserville Quick charge DMI read 2 MEMORY 01 02 03 04 05 Conventional memory Protected [...]

  • Página 127

    3 Tests and Diagnostics 3.5 Subtest Names Table 3-1 Subtest names (2/2) No. Test Name Subtest No. Subtest Name 6 PRINTER [Not supported] 01 02 03 Ripple pattern Function Wrap around 7 ASYNC [Not supported] 01 02 03 FIR/SIR Point to point (send) FIR/SIR Point to point (receive) Wrap around (board) 8 HARD DISK 01 02 03 04 05 06 07 08 09 Sequential re[...]

  • Página 128

    3.6 System Test 3 Tests and Diagnostics 3.6 System Test To execute the System Test, select 1 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 ROM Checksum This subtest executes a checksum test of the BIOS ROM (range: F0000h to F[...]

  • Página 129

    3 Tests and Diagnostics 3.6 System Test If the CPU supports Gerserville (SpeedStep), this Subtest checks that the CPU operating clock speed can be changed. Subtest 04 Quick Charge This subtest checks the status for the quick charge. Subtest 05 DMI read This subtest displays the information in the Flash-ROM in the following format. *** DMI Data Disp[...]

  • Página 130

    3.7 Memory Test 3 Tests and Diagnostics 3.7 Memory Test To execute the Memory Test, select 2 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 Conventional mem ory This subtest writes a constant data to conventional memory (0 to [...]

  • Página 131

    3 Tests and Diagnostics 3.8 Keyboard Test 3.8 Keyboard Test To execute the Keyboard Test, select 3 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 Pressed key code display When a key is pressed, the scan code, character code, a[...]

  • Página 132

    3.9 Display Test 3 Tests and Diagnostics 3.9 Display Test To execute the Display Test, select 4 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 VRAM read/write for VGA This subtest writes the constant data (AAh and 55h) to the [...]

  • Página 133

    3 Tests and Diagnostics 3.9 Display Test Subtest 04 Gradation & Mode test for VGA This subtest displays gradations for following modes. To change the mode, press Enter . [Mode 12] [Mode 13] [Mode 3] [Mode 111 640*480 64K] [Mode 112 640*480 16M] [Mode 114 800*600 64K] [Mode 115 800*600 16M] [Mode 117 1024*768 64K] [Mode 118 1024*768 16M] The dis[...]

  • Página 134

    3.9 Display Test 3 Tests and Diagnostics Subtest 06 “H” Pattern Display This subtest displays a full screen of “H” patterns. HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHH HHHHHHHHHHHHH[...]

  • Página 135

    3 Tests and Diagnostics 3.10 Floppy Disk Test 3.10 Floppy Disk Test CAUTION : Before running the floppy disk test, prepare a formatted work disk. Remove the Diagnostics Disk and insert the work disk into the FDD because the contents of the floppy disk will be erased. To execute the Floppy Disk Test, select 5 from the DIAGNOSTIC TEST MENU, press Ent[...]

  • Página 136

    3.10 Floppy Disk Test 3 Tests and Diagnostics Select the number of the subtest you want to execute and press Enter . The following message will appear during the floppy disk test. FLOPPY DISK IN PROGRESS XXXXXXX xxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] : test end [Ctrl]+[C] : key stop SUB-TEST : XX PASS COUNT : XXXXX ERROR COUNT : XXXXX WRITE DATA [...]

  • Página 137

    3 Tests and Diagnostics 3.11 Printer Test 3.11 Printer Test CAUTION : Printer Test is not supported for this model. To execute the Printer Test, select 6 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. NOTE : An IBM compatible printer must be connected to the system to execute this test. Also, printer port wrapar[...]

  • Página 138

    3.11 Printer Test 3 Tests and Diagnostics Subtest 02 Function This subtest is for IBM compatible printers, and tests the following f unctions: Normal print Double-width print Compressed print Emphasized print Double-strike print All characters print This subtest prints the various print types shown below: Subtest 03 Wraparound NOTE : To execute thi[...]

  • Página 139

    3 Tests and Diagnostics 3.12 Async Test 3.12 Async Test CAUTION : Async Test is not supported for this model. To execute the Async Test, select 7 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions displayed on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtests 01 and 02 require the fol[...]

  • Página 140

    3.13 Hard Disk Test 3 Tests and Diagnostics 3.13 Hard Disk Test To execute the Hard Disk Test, select 8 from the DIAGNOSTIC TEST MENU, press Enter , and follow the directions on the screen. CAUTION : The contents of the hard disk will be erased when subtest 02, 03, 04, 06, 08 or 09 is executed. Before running the test, the customer should transfer [...]

  • Página 141

    3 Tests and Diagnostics 3.13 Hard Disk Test 3. The Hard Disk Test message will appear after you respond to the Detail Status prompt. Select the number of the subtest you want to execute and press Enter. The following message will appear during each subtest. HARD DISK TEST XXXXXXX XXX DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] : test end [Ctrl]+[C] : key [...]

  • Página 142

    3.13 Hard Disk Test 3 Tests and Diagnostics 3-28 QOSMIO F10 Maintenance Manual (960-498) Subtest 04 Cross talk & peak shift This subtest writes eight types of worst pattern data (listed below) to a cylinder and then reads the data while moving from cylinder to cylinder. (Test the data interference in the neighbor track) Worst pattern data Cylin[...]

  • Página 143

    3 Tests and Diagnostics 3.14 Real Timer Test 3 3.14 Real Timer Test To execute the Real Timer Test, select 9 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter . Subtest 01 Real time A new date and time can be input during this subtest. To exe[...]

  • Página 144

    3.14 Real Timer Test 3 Tests and Diagnostics Subtest 03 Real time carry CAUTION : When this subtest is executed, the current date and time are erased. This subtest checks the real time clock increments. Make sure the date and time are displayed in the following form at: Current date : 12-31-1999 Current time : 23:59:58 The real time increments are [...]

  • Página 145

    3 Tests and Diagnostics 3.15 NDP Test 3.15 NDP Test To execute the NDP test, select 10 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. Subtest 01 NDP This test checks the following functions of NDP:  Control word  Status word  Bus  Addition  Multiplication QOSMIO F10 Maintenance Manual (960-498) 3[...]

  • Página 146

    3.16 Expansion Test 3 Tests and Diagnostics 3.16 Expansion Test To execute the expansion test, select 11 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. Subtest 01 PCMCIA wraparound NOTE: : PCMCIA wraparound test is not supported for this model. NOTE: To execute this subtest, the PC card wraparound connector is [...]

  • Página 147

    3 Tests and Diagnostics 3.16 Expansion Test Subtest 02 RGB monitor ID NOTE: To execute this subtest, an external monitor with monitor ID function is required. Connect the external monitor to the PC for the test of ID acquisition. The judgment of acquisition is based on the panel data. In simultaneous display mode or internal display mode, in which [...]

  • Página 148

    3.17 CD-ROM/DVD-ROM Test 3 Tests and Diagnostics 3.17 CD-ROM/DVD-ROM Test To execute the CD-ROM/DVD-ROM test, select 13 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. NOTE : For the subtest 01, 02 and 03, use the TOSHIBA CD-ROM TEST DISK TDY-01 or ABEX TEST CD-ROM TCDR-702 and DVD-ROM TEST DISK TSD-1. For the s[...]

  • Página 149

    3 Tests and Diagnostics 3.18 Error Code and Error Status Names 3.18 Error Code and Error Status Names Table 3-2 lists the error codes and error status names for the Diagnostic Test. Table 3-2 Error codes and error status names (1/3) Device name Error code Error status name (Common) FF Data Compare Error System 01 03 04 05 06 07 08 09 10 ROM - CHECK[...]

  • Página 150

    3.18 Error Code and Error Status Names 3 Tests and Diagnostics Table 3-2 Error codes and error status names (2/3) Device name Error code Error status name FDD 01 02 03 04 08 09 10 20 40 80 60 06 EE FDD - BAD COMMAND ERROR FDD - ADDRESS MARK NOT FOUND FDD - WRITE PROTECTED FDD - RECORD NOT FOUND FDD - DMA OVERRUN ERROR FDD - DMA BOUNDARY ERROR FDD -[...]

  • Página 151

    3 Tests and Diagnostics 3.18 Error Code and Error Status Names Table 3-2 Error codes and error status names (3/3) Device name Error code Error status name (HDD) CC E0 0A EE DA 12 HDD - WRITE FAULT HDD - STATUS ERROR HDD - BAD SECTOR HDD - ACCESS TIME ERROR HDD - NO HDD HDD - DMA CRC ERROR NDP 01 02 03 04 05 06 NDP - NO CO-PROCESSOR NDP - CONTROL WO[...]

  • Página 152

    3.19 Hard Disk Test Detail Status 3 Tests and Diagnostics 3.19 Hard Disk Test Detail Status When an error occurs in the hard disk test, the following message is displayed: HDC status = XXXXXXXX Detailed information about the hard disk test error is displayed on the screen by an eight- digit number. The first four digits represent the hard disk cont[...]

  • Página 153

    3 Tests and Diagnostics 3.19 Hard Disk Test Detail Status Table 3-4 Error register contents Bit Name Description 7 BBK (Bad block mark) “0” … Not used “1” … A bad block mark is detected. 6 UNC (Uncorrectable) “0” … There is no uncorrectable data error. “1” … Uncorrectable data error has been detected. 5 —— Not used 4 IDN[...]

  • Página 154

    3.20 ONLY ONE TEST 3 Tests and Diagnostics 3.20 ONLY ONE TEST 3.20.1 Program Description This program tests the unique functions of this model. 3.20.2 Operations Select test 2 from the DIAGNOSTIC MENU and press Enter . The following menu appears in the display. ################################################################# ######## ONLY ONE TEST[...]

  • Página 155

    3 Tests and Diagnostics 3.20 ONLY ONE TEST Subtest 01 Pressed key display When you execute this subtest, the keyboard layout is drawn on the display as shown below. When any key is pressed, the corresponding key on the screen changes to the key character that was pressed. Holding a key down enables the auto-repeat function which causes the key’s [...]

  • Página 156

    3.20 ONLY ONE TEST 3 Tests and Diagnostics Subtest 02 Touch Pad This subtest checks the functions of the touch pad as shown below. A) Direction and parameter B) Switching function check. This test displays the response from the touch pad and touch pad switch. When moving your finger on the touch pad towards the upper left, the <POINTING> disp[...]

  • Página 157

    3 Tests and Diagnostics 3.20 ONLY ONE TEST Subtest 03 GP Button This subtest checks if the AV buttons (10 buttons) work properly. The following m essage appears in the display. Press button [0] Press the AV button from the left (the AV button nearest to power button). The name of AV buttons in the message is described as num ber (0-9) from the left[...]

  • Página 158

    3.20 ONLY ONE TEST 3 Tests and Diagnostics Slide the switch to OFF position. Then, the following message appears in the display. KILL SWITCH ON !! Slide the switch to ON position. Then, the following message appears in the display. KILL SWITCH OFF !! After Sliding the switch to OFF position, the screen returns to the ONLY ONE TEST menu automaticall[...]

  • Página 159

    3 Tests and Diagnostics 3.20 ONLY ONE TEST Subtest 06 Touch Pad (Scroll Button) This subtest checks if the scroll button of touch pad works properly. The following m essage appears in the display. ****** Scroll button TEST (VX.XX) ****** Press Scroll button Up Button xxx Down Button xxx Press [ESC] key to EXIT Check the message “xxx” changes to[...]

  • Página 160

    3.20 ONLY ONE TEST 3 Tests and Diagnostics Press Enter and following message appears in the display. Check [PowerSW-LED]= Green Check if the Power Switch LED lights in the following order. (Green -> Orange -> Blue -> OFF) Press any key and the following m essage appears in the display. Check [DC-IN]&[Power]&[Main Battery]LED= Green[...]

  • Página 161

    3 Tests and Diagnostics 3.21 Head Cleaning 3.21 Head Cleaning 3.21.1 Function Description This function cleans the heads in the FDD by executing a series of head load/seek and read operations. A cleaning kit is necessary to perform this program. 3.21.2 Operations 1. Selecting test 4 from the DIAGNOSTIC MENU and pressing Enter displays the following[...]

  • Página 162

    3.22 Log Utilities 3 Tests and Diagnostics 3.22 Log Utilities 3.22.1 Function Description This function logs error information generated while a test is in progress and stores the results in RAM. This function can store data on a floppy disk, or output the data to a printer or the display. The error information is displayed in the following order: [...]

  • Página 163

    3 Tests and Diagnostics 3.22 Log Utilities 3.22.2 Operations 1. Select 5 and press Enter in the DIAGNOSTIC MENU, the error information is displayed in the following format: XXXXX ERRORS CNT TS-NO PASS STS ADDR WD RD HSTS [ERROR STATUS NAME] 001 FDD 02 0000 103 00001 00 00 0000 FDD-WRITE PROTECTED 001 FDD 01 0000 180 00001 00 00 0000 FDD-TIME OUT ER[...]

  • Página 164

    3.23 Running Test 3 Tests and Diagnostics 3.23 Running Test 3.23.1 Function Description This function automatically executes the following tests in sequence: 1. System test (subtest 01) 2. Memory test (subtests 01, 02, 06) 3. Display test (subtest 01) 4. Real timer test (subtest 02) 5. HDD test (subtests 01) The system automatically detects the num[...]

  • Página 165

    3 Tests and Diagnostics 3.24 Floppy Disk Drive Utilities 3.24 Floppy Disk Drive Utilities 3.24.1 Function Description This function formats the FDD, copies the floppy disk and displays the dump list for both the FDD and HDD. 1. FORMAT NOTE : This program is only for testing a floppy disk drive. It is different from the Toshiba MS-DOS FORMAT command[...]

  • Página 166

    3.24 Floppy Disk Drive Utilities 3 Tests and Diagnostics 3.24.2 Operations 1. Selecting 7 from the DIAGNOSTIC MENU and pressing Enter displays the following message: [ FDD UTILITIES ] 1 - FORMAT 2 - COPY 3 - DUMP 4 – HDD-ID READ 9 - EXIT TO DIAGNOSTICS MENU 2. FORMAT program (a) Selecting FORMAT displays the following message: DIAGNOSTICS - FLOPP[...]

  • Página 167

    3 Tests and Diagnostics 3.24 Floppy Disk Drive Utilities 3. COPY program (a) When COPY is selected, the following message appears: FLOPPY DISK FORMAT & COPY : VX.XX Type select (0:2DD,3:2HD) ? (b) Selecting a media/drive type number will display a m essage similar to the one below: Insert source disk into drive A: Press any key when ready. (c) [...]

  • Página 168

    3.24 Floppy Disk Drive Utilities 3 Tests and Diagnostics 4. DUMP program (a) When DUMP is selected, the following message appears: DIAGNOSTICS-HARD DISK & FLOPPY DISK DUMP : VX.XX Drive type select (1:FDD, 2:HDD) ? (b) Select a drive type. If 2:HDD is selected, the display will go to step (h). If 1:FDD is selected, the following message will ap[...]

  • Página 169

    3 Tests and Diagnostics 3.24 Floppy Disk Drive Utilities QOSMIO F10 Maintenance Manual (960-498) 3-55 (k) The following message will appear. To finish the dum p, select 3 . Press number key (1:up,2:down,3:end) ? (l) The following message will appear. Selecting 2 returns to the FDD UTILITIES MENU. Another dump (1:Yes,2:No) ? 5. HDD ID READ program S[...]

  • Página 170

    3.25 System Configuration 3 Tests and Diagnostics 3 3.25 System Configuration 3.25.1 Function Description NOTE : To display the system configuration, the write protect tab should be OFF position. If the tab is ON position, move the tab to OFF position and restart the test. Otherwise the correct information cannot be acquired. The System Configurati[...]

  • Página 171

    3 Tests and Diagnostics 3.25 System Configuration 3.25.2 Operations Select 8 from the DIAGNOSTIC MENU and press Enter. Then, the following system configuration appears in the display. System Configuration Display : Ver X.XX [Machine Name ???] * - Processor Type = XXXXXX-XXXXXMHz Code = XX L2 Cache = XXXXXKB * - Chip set = XXXXXX VRAM = XXXXMB * - B[...]

  • Página 172

    3.26 Wireless LAN Test Program (Intel-made b/g) 3 Tests and Diagnostics 3.26 Wireless LAN Test Program (Intel-made b/g) This section describes how to perform the wireless LAN transm itting-receiving test (Intel- made Calexico 802.11b/g). To execute the wireless LAN test, use the Diagnostics disk for wireless LAN test. Finish the tests of the Main t[...]

  • Página 173

    3 Tests and Diagnostics 3.26 Wireless LAN Test Program (Intel-made b/g) W hen a defective is detected in the test, following typical cause is considered. Bad connection of wireless LAN card • • • • • • Using a wrong wireless LAN card (Using unspecified card) Defective wireless LAN card Check the connection and execute the subtest again.[...]

  • Página 174

    3.26 Wireless LAN Test Program (Intel-made b/g) 3 Tests and Diagnostics Subtest03 Antenna check & communication test of 11b mode Caution: To execute subtest 03-05, use another computer (with Calexico wireless LAN card) that can communicate by the wireless LAN as a responder machine. Access points are also required. (Access point for 802.11b and[...]

  • Página 175

    3 Tests and Diagnostics 3.26 Wireless LAN Test Program (Intel-made b/g) Check the connection and condition, and execute the subtest again. Subtest04 Communication test of 11g mode This subtest checks the communication of wireless LAN antenna of Calexico 802.11g mode. After finishing the test, OK message will appear in the display. Press any key to [...]

  • Página 176

    3.27 Wireless LAN Test Program (Intel-made a/b/g) 3 Tests and Diagnostics 3.27 Wireless LAN Test Program (Intel-made a/b/g) This section describes how to perform the wireless LAN transm itting-receiving test (Intel- made Calexico 802.11a/b/g). To execute the wireless LAN test, use the Diagnostics disk for wireless LAN test. Finish the tests of the [...]

  • Página 177

    3 Tests and Diagnostics 3.27 Wireless LA N Test Program (Intel-made a/b/g) If a defective is found during the test, NG m essage will appear in the display. Press any key and f ollowing message will appear in the display. ************************************************************* * * * SKU NG !! * * * * Other Card or Module not found * * * ******[...]

  • Página 178

    3.27 Wireless LAN Test Program (Intel-made a/b/g) 3 Tests and Diagnostics Press any key to return to the test m enu. W hen a defective is detected in the test, following typical cause is considered. Bad connection of wireless LAN card • • • Defective wireless LAN card Disappearance of MAC address data Check the connection and execute the subt[...]

  • Página 179

    3 Tests and Diagnostics 3.27 Wireless LA N Test Program (Intel-made a/b/g) Press any key to return to the test menu. W hen a defective is detected in the test, following typical cause is considered. Bad connection of wireless LAN card • • • • • • • • Bad connection of wireless LAN antenna cable (Main/Aux) Bad environment for wireles[...]

  • Página 180

    3.27 Wireless LAN Test Program (Intel-made a/b/g) 3 Tests and Diagnostics Subtest05 Communication test of 11g mode This subtest checks the communication of wireless LAN antenna of Calexico 802.11g mode. For m ore details on procedure and contents of this subtest, refer to Subtest04 Communication test of 11a m ode. Subtest06 All the tests of Calexic[...]

  • Página 181

    3 Tests and Diagnostics 3.28 Wireless LAN Test Program (Askey-made) 3.28 Wireless LAN Test Program (Askey-made) This section describes how to perform the wireless LAN transm itting-receiving test (Askey- made Atheros b/g, a/b/g). Caution: To execute subtest 03-07, use another computer (with Atheros wireless LAN card) that can communicate by the wir[...]

  • Página 182

    3.28 Wireless LAN Test Program (Askey-made) 3 Tests and Diagnostics 4. When the program disk 2 starts, f ollowing menu will appear in the display. To execute the subtest, press test number and Enter . ******************************************************* * Atheros MB4x(MB44ag/43g) Maintenance T&D Menu * * * * 1 : SKU check of Module * * * * 2[...]

  • Página 183

    3 Tests and Diagnostics 3.28 Wireless LAN Test Program (Askey-made) Subtest02 MAC Address Check This subtest reads out the MAC address of the card installed and confirm s if it is valid. When the MAC address is valid one, following m essage will appear in the display. ************************************************************* * * * MAC Address C[...]

  • Página 184

    3.28 Wireless LAN Test Program (Askey-made) 3 Tests and Diagnostics Moreover, following typical cause is considered. Bad connection of wireless LAN card • • • • Bad connection of wireless LAN antenna cable (Main/Aux) Environment for wireless LAN comm unication (Interference/ obstruction) Defective wireless LAN card Check the connection and [...]

  • Página 185

    3 Tests and Diagnostics 3.29 LAN/M odem/Bluetooth/IEEE1394 Test Program 3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program This section describes how to perform the LAN/Modem/Bluetooth/IEEE1394 test with the test program. Insert the test program disk for LAN/Mode m/Bluetooth/IEEE1394 test in FDD and turn on the power. The following message will appear:[...]

  • Página 186

    3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics Subtest01 (i82562 + ICHx) This subtest checks the operation of mini-PCI I/F by the loopback test in the chip. The following message will appear: [LAN transmit & receive test !] COMPLETED Repeat count = 00000 Error count = 00000 LOOPBACK TEST 100Mbps Auto-negotiation TxRx Tes[...]

  • Página 187

    3 Tests and Diagnostics 3.29 LAN/M odem/Bluetooth/IEEE1394 Test Program Subtest02 (GbE) CAUTION : Gigabit Ethernet (GbE) test is not supported for this model. This subtest checks the operation of mini-PCI I/F by the loopback test in the chip. Select 2 to execute and press Enter . The following message will appear: Testing adaptor...hit <ESC> [...]

  • Página 188

    3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics 3.29.2 Modem test For this subtest, connect the modem PCB and RJ11 connector with a harness. Use the dedicated “FAT-MODE inspection device (product code: QE2000P01 made by Nitto Electric Manufacture Co.,Ltd)” for the tests. To execute Modem test, press 2 and Enter . Followin[...]

  • Página 189

    3 Tests and Diagnostics 3.29 LAN/M odem/Bluetooth/IEEE1394 Test Program 3.29.3 Bluetooth test CAUTION : Bluetooth test is not supported for this model. To execute this test, input 3 and press Enter . Note : Use another computer that can communicate by the Bluetooth as a reference machine to perform this test. Insert a floppy disk containing the tes[...]

  • Página 190

    3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics Subtest01 BD_ADDR check This subtest checks the BD_ADDR functions. When the Bluetooth test menu is displayed, press 1 to select the test and press Enter . The following message will appear: ----------------------------------------------------------------------------- Bluetooth S[...]

  • Página 191

    3 Tests and Diagnostics 3.29 LAN/M odem/Bluetooth/IEEE1394 Test Program If the target machine has any problem, it displays Error m essasge. The following message is displayed. ----------------------------------------------------------------------------- Bluetooth Subsystem T&D for PCSE(BD_ADDR) VerX.XX Copyright (C) by TOSHIBA Co. -------------[...]

  • Página 192

    3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics If the machine detects a malfunction, it indicates the error code as shown below. The error code begins with the least significant digit. Error code Table 3-6 Error code for Bluetooth test (BD_ADDR) (1/2) Error code Meaning 0x01 Unknown HCI Command. 0x02 No Connection. 0x03 Hard[...]

  • Página 193

    3 Tests and Diagnostics 3.29 LAN/M odem/Bluetooth/IEEE1394 Test Program Table 3-6 Error code for Bluetooth test (BD_ADDR) (2/2) Error code Meaning 0x20 Unsupported LMP Parameter Value. 0x21 Role Change Not Allowed. 0x22 LMP Response Timeout. 0x23 LMP Error Transaction Collision. 0x24 LMP PDU Not Allowed. 0x25 Not Exist 0x26 Not Exist 0x27 Not Exist[...]

  • Página 194

    3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics ----------------------------------------------------------------------------- Bluetooth Subsystem T&D for PCSE(CS-Air) VerX.XX Copyright (C) by TOSHIBA Co. ----------------------------------------------------------------------------- +----------------------+ | DUT | BD_ADDR [...]

  • Página 195

    3 Tests and Diagnostics 3.29 LAN/M odem/Bluetooth/IEEE1394 Test Program ----------------------------------------------------------------------------- Bluetooth Subsystem T&D for PCSE(CS-Air) VerX.XX Copyright (C) by TOSHIBA Co. ----------------------------------------------------------------------------- +----------------------+ | DUT | BD_ADDR[...]

  • Página 196

    3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics If any problem is detected during the test, the massage FAIL is displayed on the tester machine with the error code as shown below. The error code begins with the least significant digit. Error code Table 3-7 Error code for Bluetooth test (BD_ADDR of the DUT) (1/2) Error code Me[...]

  • Página 197

    3 Tests and Diagnostics 3.29 LAN/M odem/Bluetooth/IEEE1394 Test Program Table 3-7 Error code for Bluetooth test (BD_ADDR of the DUT) (2/2) Error code Meaning 0x20 Unsupported LMP Parameter Value. 0x21 Role Change Not Allowed. 0x22 LMP Response Timeout. 0x23 LMP Error Transaction Collision. 0x24 LMP PDU Not Allowed. 0x25 Not Exist 0x26 Not Exist 0x2[...]

  • Página 198

    3.29 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics 3-84 QOSMIO F10 Maintenance Manual (960-498) 3.29.4 IEEE1394 test To execute this test, input 4 and press Enter . NOTE: Use another computer that can communicate by IEEE1394 (i. Link) cable as a responder machine to perform this test. The following menu will appear: ************[...]

  • Página 199

    3.30 Sound Test program 3 Tests and Diagnostics 3 Tests and Dia tics 3.30 Sound Test program gnos This section describes how to perform the Sound test. To execute the sound test, refer to the following description. Insert the test program disk for Sound test in the floppy disk drive and turn on the power. The following message will appear: ########[...]

  • Página 200

    3.30 Sound Test program 3 Tests and Diagnostics To return to the Sound test menu, Press 9 and Enter . Then following message will appear in the display. *********************************** ******** May I Restart ? ******* *********************************** Press any key to continue… After pressing any key, the machine starts rebooting and sound [...]

  • Página 201

    3 Tests and Diagnostics 3.30 Sound Test program Subtest02 Sine Wave This subtest is executed by loading the COM file (ADSIN.COM). The program expands sine wave data table from 16KB to 64KB, and creates the play data. Then it transfers the data between the DMA and the CODEC to play the sine wave. (It sounds like a continuous beep). By using wave mea[...]

  • Página 202

    3.30 Sound Test program 3 Tests and Diagnostics 3.30.3 CD Sound (Standard) test To execute the CD Sound (Standard) test, press 3 and Enter . Insert the test media (TOSHIBA TEST CD-ROM or ABEX TEST CD-ROM) or music CD on the market (if the test media can not be prepared). The menu appears in the display. For details on use of test media, refer to (1[...]

  • Página 203

    3 Tests and Diagnostics 3.30 Sound Test program Subtest02 English Narration W hen selecting this subtest, narration in English starts. For m ore details on the procedure, refer to the subtest01. Subtest03 Test Tone A Caution: Before starting subtest03, be sure to set the sound at proper volume. This subtest plays sine wave while changing its table [...]

  • Página 204

    3.30 Sound Test program 3 Tests and Diagnostics (2) Audio CD Insert an audio CD and the following menu appears in the display. CD/DVD TEST IN PROGRESS XXXXXXXX xxxxxxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] ; test end [Ctrl]+[C] ; key stop SUB-TEST : XX PASS COUNT : XXXXX ERROR COUNT: XXXXX WRITE DATA : XX READ DATA : XX ADDRESS : XXXXXX STATUS : XXX[...]

  • Página 205

    3 Tests and Diagnostics 3.31 SETUP 3.31 SETUP 3.31.1 Function Description This program displays the current system setup inform ation as listed below: 1. Memory 2. System Date/Time 3. Battery 4. Password 5. Boot Priority (a) Boot Priority (b) Network Boot Protocol 6. Display (a) Power On Display (b) LCD Display Stretch (c) TV Type 7. Others (a) CPU[...]

  • Página 206

    3.31 SETUP 3 Tests and Diagnostics 3.31.2 Accessing the SETUP Program While pressing ESC , turn on the power. Then press F1 . The following display appears. NOTE : *1 This message appears only on the model for TCL (Canada). 3-92 QOSMIO F10 Maintenance Manual (960-498)[...]

  • Página 207

    3 Tests and Diagnostics 3.31 SETUP Moving Within the SETUP Menu and Changing Values 1. Press Å and Æ to move between the two columns. Press ↑ and ↓ to m ove between items in a column. Press Fn + ↑ ( PgUp) and Fn + ↓ ( PgDn) to move between the two pages. 2. Press either the Space bar or Back Space to change the value. Accepting Changes an[...]

  • Página 208

    3.31 SETUP 3 Tests and Diagnostics SETUP Options The SETUP screen is divided into 13 functionally related groups. This section describes each group and its options. 1. Memory This group of options displays the computer’s mem ory. This field displays the total amount of mem ory installed and is automatically calculated by the computer. You cannot [...]

  • Página 209

    3 Tests and Diagnostics 3.31 SETUP NOTE: Display of the LCD Brightness will be changed in the condition below: (*1) Operating the battery (*2) Using the AC adapter User Setting Use this option to set the battery save parameters on the sub-window, BATTERY SAVE OPTIONS . Battery Save Options Processing Speed This feature changes the CPU processing sp[...]

  • Página 210

    3.31 SETUP 3 Tests and Diagnostics HDD Auto Off Use this option to set the duration of the HDD automatic power off function. xx Min. Automatically turns off the power to the hard disk drive if it is not used for the duration set. The duration xx can be set to 1 , 3 , 5 , 10 , 15 , 20 or 30 minutes. LCD Brightness Use this option to set the level of[...]

  • Página 211

    3 Tests and Diagnostics 3.31 SETUP 4. Password This option sets or resets the user password for power on and instant security ( Fn+F1 ). Registered The user password has been registered. Not registered The user password has not been registered. For details on setting the user password, refer to the User’s Manual. 5. Boot Priority (a) Boot Priorit[...]

  • Página 212

    3.31 SETUP 3 Tests and Diagnostics This option is used to select the display when booting up. Auto-Selected Selects an external monitor if one is connected. Otherwise it selects the internal LCD. (Default) LCD+AnalogRGB Selects both the internal LCD and the external monitor for simultaneous display. NOTE : When starting the computer in Standby or h[...]

  • Página 213

    3 Tests and Diagnostics 3.31 SETUP 7. Others Whether or not you need to configure the computer with these options depends primarily on the kind of software or peripherals you use. (a) CPU Cache Use this option to enable or disable the CPU cache. Enabled Enables the CPU cache. (Default) Disabled Disables the CPU cache. (b) Level 2 Cache Use this opt[...]

  • Página 214

    3.31 SETUP 3 Tests and Diagnostics Set the parameters for the Auto Power On (automatic power on) function in the “OPTIONS” window. To set the time, use Space bar or BackSpace . Press ↓ to move the cursor to the right and ↑ to move the cursor to the left when you set the date and time. For the Alarm Time , set the time to turn on the power a[...]

  • Página 215

    3 Tests and Diagnostics 3.31 SETUP Mode 2 Sets to Mode 2. Glows blue (Power ON) / Alternately flashes green and orange (Standby) / Alternately flashes green and blue (Power OFF/Hibernation) Mode 3 Sets to Mode 3. Flashes in order of green, orange and blue (Power ON) / Glows yellow (Standby) / Glows orange (Power OFF /Hibernation) (h) Language Durin[...]

  • Página 216

    3.31 SETUP 3 Tests and Diagnostics 11. Peripheral Use this option to select the peripheral's mode. (a) Internal Pointing Device This option enables or disables the touch pad Enabled Enables the touch pad. (Default) Disabled Disables the touch pad. (b) Hard Disk Mode Use this option to select the hard disk mode. Enhanced IDE (normal) Select thi[...]

  • Página 217

    3 Tests and Diagnostics 3.31 SETUP 13. PCI LAN This option sets the Enable / Disable of the built-in LAN functions. Enabled Enables built-in LAN functions. (Default) Disabled Disables built-in LAN functions. QOSMIO F10 Maintenance Manual (960-498) 3-103[...]

  • Página 218

    3.31 SETUP 3 Tests and Diagnostics 3-104 QOSMIO F10 Maintenance Manual (960-498)[...]

  • Página 219

    Chapter 4 Replacement Procedures[...]

  • Página 220

    4 Replacement Procedures 4 4-ii QOSMIO F 10 Maint enance Ma nual (960 -498)[...]

  • Página 221

    4 Replacement Procedures Chapter 4 Contents 4.1 Overview ................................................................................................................... .4 - 1 Safety Precautions ................................................................................................ 4-2 Before You Begin .................................[...]

  • Página 222

    4 Replacement Procedures 4.14.2 Guide ..................................................................................................... 4-42 4.15 Heat sink/CPU ......................................................................................................... 4-44 4.16 VGA Heat sink ........................................................[...]

  • Página 223

    4 Replacement Procedures Figures Figure 4-1 Removing the battery pack................................................................................. 4-8 Figure 4-2 Removing the PC card ..................................................................................... 4-10 Figure 4-3 Removing th e bridge media ..................................[...]

  • Página 224

    4 Replacement Procedures 4-vi QOSMIO F 10 Mainten ance Manu al (960- 498) Figure 4-30 Applying si licon grease .................................................................................... 4-46 Figure 4-31 Removing the VGA heat sink .......................................................................... 4-47 Figure 4-32 Removing the PC ca[...]

  • Página 225

    4 Replacement Procedures 4.1 Overview 4 4.1 Overview This chapter describes the procedure for rem oving and replacing the fi eld replaceable units (FRUs) in the PC. It may not be necessary to remove all the F RUs in order to replace one. The chart below provides a guide as to whic h other FRUs must be removed before a particular FRU can be removed.[...]

  • Página 226

    4.1 Overview 4 Replacement Procedures Safety Precautions Please read the following safety instructions before disassembling the computer and always follow the instructions w hile working on the computer. DANGER: 1. In the case of the battery, always use authentic parts or equivalent parts approved by Toshiba. Other batteries may have different spec[...]

  • Página 227

    4 Replacement Procedures 4.1 Overview Before You Begin Take note of the following points before star ting work. Always remove the AC adapter and battery pack before commencing any of the procedures. The procedure for removing the battery pack is described in section “4.2.1 Battery Pack”. 1. Do not disassemble the computer unless it is operating[...]

  • Página 228

    4.1 Overview 4 Replacement Procedures Disassembly Procedure Three main types of cable connector are used. Pressure plate connector • • • Spring connector Normal pin connector When disconnecting a pressure plate connector, lift up the tag on one side of the plastic pressure plate on the connector and pull the cab le out from the connect or. W [...]

  • Página 229

    4 Replacement Procedures 4.1 Overview Assembly Procedure After the computer has been disassembled and th e part that caused the fault has been repaired or replaced, the computer must be reassem bled. Take note of the following general points when assembling the computer. Take your time and follow the instructions carefully. Hurrying the assembly wo[...]

  • Página 230

    4.1 Overview 4 Replacement Procedures Screw Tightening Torque Use the following torque when tightening screws. CAUTION : Overtightening may damage screws or parts. Undertightening may allow screws to loosen (and possibly fall ou t) causing a short circuit or other damage. NOTE : To tighten screws quickly and accu rately, an electric screwdriver is [...]

  • Página 231

    4 Replacement Procedures 4.1 Overview Screw Notation To make maintenance of the co mputer easier, markings of the kinds of the screws including the types and lengths of the screws are indicated on the computer body. Format: Screw shape + Screw length (mm) Screw shape B: Bind screw F: Thin head screw S: Super thin head screw T: Tapping screw U: Othe[...]

  • Página 232

    4.2 Battery pack/PC card/Bridge Me dia 4 Replacement Procedures 4.2 Battery pack/PC card/Bridge Media 4.2.1 Battery pack Removing the battery pack The following describes the procedure for re m oving the battery pack (See Figure 4-1). CAUTION: Take care not to short circuit the terminals when removing the batter y pack. Similarly, do not drop, knoc[...]

  • Página 233

    4 Replacement Procedures 4.2 Battery pack/PC card/Bridge Media NOTE : Dispose of the used battery pack in a ccordance with the laws and ordinances of your local authority. Installing the battery pack The following describes the procedure for rein stalling the battery pack (See Figure 4-1). CAUTION: The lithium ion battery pack may explode if not fi[...]

  • Página 234

    4.2 Battery pack/PC card/Bridge Me dia 4 Replacement Procedures 4.2.2 PC card Removing the PC card The following describes the procedure for removing the PC card (See Figure 4-2). CAUTION: Insert or remove the PC card in accordance with any instructions in the PC card manual or the manuals of the computer system you are using. 1. Push the eject but[...]

  • Página 235

    4 Replacement Procedures 4.2 Battery pack/PC card/Bridge Media 4.2.3 Bridge Media (SD Card / Memory Stick / xDPicture Card/Multi Media Card) Removing the Bridge media The following describes the procedure for re m oving the bridge media (See Figure 4-3). CAUTION: Insert or remove the Bridge Media in accordance with any instructions in the each Brid[...]

  • Página 236

    4.3 HDD 4 Replacement Procedures 4.3 HDD Removing the HDD The following describes the procedure for removing the HDD (See Figure 4-4 and 4-5). CAUTION: Be careful not to drop or leave screws in the PC. Take care not to press on the top or bottom of the HDD. Pre ssure may cause data loss or damage to the device. 1. Turn the computer upside down. 2. [...]

  • Página 237

    4 Replacement Procedures 4.3 HDD 4. Remove the following screws fixing the HDD assembly . • F3 × 4S FLAT BIND screw x4 5. Detach the HDD holder from the HDD . 6. Pull out the laminate cover to the arrow direction a nd detach it from the HDD. HDD F3 × 4S FLAT BIND HDD holde r F3 × 4S FLAT BIND Laminate cover Figure 4-5 Removing the HDD QOSMIO F[...]

  • Página 238

    4.3 HDD 4 Replacement Procedures Installing the HDD The following describes the procedure for in stalling an HDD (See Figure 4-4 and 4-5). 1. Attach the laminate cover to the HDD. 2. Install the HDD to the HDD holder and secure them with the following screws . • F3 × 4S FLAT BIND screw x4 NOTE: Although they are 3mm head screws, screw torque mus[...]

  • Página 239

    4 Replacement Procedures 4.4 Memory module 4.4 Memory module CAUTION: The power of the computer must be turned off when you remove the memory module. Removing a memory module with the power on risks damaging the module or the computer itself. Do not touch the memory module termi nals. Any dirt on the terminals may cause memory access problems. Neve[...]

  • Página 240

    4.4 Memory module 4 Replacement Procedures Installing the memory module To install the memory module, confirm that the computer is in boot m ode. Then perform the following procedure (See Figure 4-6). 1. Insert the memory module into the connector of the computer slantwise (term inal side first) and press it to connect firmly. CAUTION: The power mu[...]

  • Página 241

    4 Replacement Procedures 4.5 Keyboard/Bluetooth 4.5 Keyboard/Bluetooth 4.5.1 Keyboard Removing the keyboard The following describes the procedure for rem o ving the keyboard (See Figure 4-7 to 4-9). CAUTION: As the keytop may fall out, when handli ng the keyboard always hold it by the frame and do not touch the keytop. 1. Open the display. 2. Inser[...]

  • Página 242

    4.5 Keyboard/Bluetooth 4 Replacement Procedures 5. Remove the following screws fixing the keyboard • M2.5 × 2.8B FLAT BIND screw x2 M2.5x2.8B FLAT BIND Figure 4-8 Removing the keyboard 6. Lift the upper side of the keyboard and turn it face down on the palm rest. 4-18 QOSMIO F 10 Maint enance Ma nual (960 -498)[...]

  • Página 243

    4 Replacement Procedures 4.5 Keyboard/Bluetooth 7. Remove the following screws fixing the keyboard support plate . • M2.5 × 2.8B FLAT BIND screw x2 8. Remove the keyboard support plate . M2.5 × 2.8B FLAT BIND Slit Keyboard support plate CN3230 Keyboard Ke y board flexible cable Figure 4-9 Removing the keyboard support plate 9. Pull out the keyb[...]

  • Página 244

    4.5 Keyboard/Bluetooth 4 Replacement Procedures Installing the keyboard The following describes the procedure for inst alling the keyboard (See Figure 4-7 to 4-9). 1. Turn the keyboard upside down and place it on the palm rest as its face down. Connect the keyboard flexible cable to the connector CN3230 on the system board. NOTE: After connecting t[...]

  • Página 245

    4 Replacement Procedures 4.5 Keyboard/Bluetooth 4.5.2 Bluetooth Removing the Bluetooth The following describes the procedure for rem oving the bluetooth (See Figure 4-10). 1. Disconnect the bluetooth flat cable from the connector CN4400 on the system board. 2. Turn up the insulator to take out the bluetooth module from the guide of the display asse[...]

  • Página 246

    4.6 Switch membrane 4 Replacement Procedures 4.6 Switch membrane Removing the switch membrane The following describes the procedure for rem o ving the switch membrane (See Figure 4-11). 1. Remove the following screw and remove the LCD CON holder . • M2.5 × 6B FLAT BIND screw x1 2. Disconnect the switch membrane from the connector CN9650 on the s[...]

  • Página 247

    4 Replacement Procedures 4.6 Switch membrane Installing the switch membrane The following describes the procedure for inst alling the switch membrane (See Figure 4-11). 1. Connect the switch membrane to the connector CN9650 on the system board. 2. Slide the switch membrane to install and secure it with the following screw . • M2.5 × 2.8B FLAT BI[...]

  • Página 248

    4.7 Optical drive 4 Replacement Procedures 4.7 Optical drive NOTE : Do not apply excessive force to the top of an optical drive. Do not touch the shaded portion of the fi gure below, when you remove or install the drive. Removing the optical drive The following describes the procedure for rem ovi ng the optical drive (S ee Figure 4-12 and 4- 13). 1[...]

  • Página 249

    4 Replacement Procedures 4.7 Optical drive 3. Remove the following screws to remove the side bracket from the optical drive. • M2 × 3C SUPER THIN HEAD screw x2 • M2 × 3.2 Stepping screw x1 Stepping screw Side bracket M2 × 3C SUPER THIN HEAD Figure 4-13 Disassembling the side bracket Installing the optical drive The following describes the pr[...]

  • Página 250

    4.8 Display assembly 4 Replacement Procedures 4.8 Display assembly Removing the display assembly The following describes the procedure for rem o ving the display assembly (See Figure 4-14 to 4-18). 1. Close the display and turn the computer upside down. 2. Remove the following screws from the bottom of the com puter. • M2.5 × 10B FLAT BIND screw[...]

  • Página 251

    4 Replacement Procedures 4.8 Display assembly 3. Tun over the computer and open the display. 4. Remove the following screws and remove the harness cover . • M2.5 × 6B FLAT BIND screw x2 • M2.5 × 10B FLAT BIND screw x1 M2.5 × 10B FLAT BIND Harness cover M2.5 × 6B FLAT BIND Figure 4-15 Removing the screws (front) QOSMIO F 10 Maint enance Ma n[...]

  • Página 252

    4.8 Display assembly 4 Replacement Procedures 5. Disconnect the LCD harness from the connector PJ5600 on the system board. 6. Unlock the connector CN3201 and disconnect the touch pad cable from the connector on the system board. 7. Unlock the connector CN9550 and disconnect the SJ board flat cable from the connector on the sound board. 8. Take out [...]

  • Página 253

    4 Replacement Procedures 4.8 Display assembly 9. Lift up the display assembly from the Optical drive side first to unhook the latches. 10. Remove the display assembly from the base assembly and place it next to the base assembly. 11. Remove the following screws and remove the w ireless LAN cover on the base assembly. • M2 × 4Z BIND screw x1 Opti[...]

  • Página 254

    4.8 Display assembly 4 Replacement Procedures 12. Disconnect the w ireless LAN antenna cables from the wireless LAN board. Wireless LAN antenna cable Aux (black) Wireless LAN antenna cable Main (white) Figure 4-18 Removing the wireless LAN antenna cables 4-30 QOSMIO F 10 Maint enance Ma nual (960 -498)[...]

  • Página 255

    4 Replacement Procedures 4.8 Display assembly Installing the display assembly The following describes the procedure for instal ling the display assem bly (See Figure 4-14 to 4-18). 1. Connect the wireless LAN antenna cables (Main (white cable ) and Aux (black cable)) to the connectors on the wireless LAN board. 2. Install the wireless LAN cover and[...]

  • Página 256

    4.9 SD board/MDC 4 Replacement Procedures 4.9 SD board/MDC 4.9.1 SD board Removing the SD board The following describes the procedure for removing the SD board (See Figure 4-19). 1. Disconnect the SD board flat cable from the connector CN9510 on the SD board. 2. Disconnect the SVP harness from the connector CN9615 on the SD board. 3. Disconnect the[...]

  • Página 257

    4 Replacement Procedures 4.9 SD board/MDC M2.5x4B FLAT BIND SVP harness CN2410 SD board flat cable RJ11 connecto r Speaker cable L TV tuner cable CN9614 TV tuner coaxial cable M2.5x4B FLAT BIND Core CN9510 CN9615 USB harness CN4620 PJ6002 PJ6003 Speaker cable R Figure 4-19 Removing the SD board Installing the SD board The following describes the pr[...]

  • Página 258

    4.9 SD board/MDC 4 Replacement Procedures 4-34 QOSMIO F 10 Maint enance Ma nual (960 -498) 4.9.2 MDC Removing the MDC The following describes the procedure for removing the MDC (See Figure 4-20). 1. Turn over the SD board. 2. Remove the following screws fixing the MDC and pull the MDC straight up from the connector CN3000 on the SD board. • M2 ×[...]

  • Página 259

    4 Replacement Procedures 4.10 Fan 4 4.10 Fan Removing the fan The following describes the procedure for rem oving the fan (See Figure 4-21). 1. Disconnect the fan cable from the CN8770 on the system board. 2. Remove the following screws and remove the fan. • M2.5 × 4B FLAT BIND screw x2 M2.5x4B FLAT BIND Fan cable CN8770 S p ace Figure 4-21 Remo[...]

  • Página 260

    4.11 Wireless LAN board 4 Replacement Procedures 4.11 Wireless LAN board Removing the wireless LAN board The following describes the procedure for re m oving the wireless LAN board (See Figure 4- 22). 1. Open the left and right latches holding the wireless LAN board and remove it. Latches Figure 4-22 Removing th e wireless LAN board Installing the [...]

  • Página 261

    4 Replacement Procedures 4.12 System board 4.12 System board CAUTION: 1. When handling the system board, alwa ys hold by the edges. Do not touch the printed circuit face. 2. If replacing with a new system board, execute the subtest01 Initial configuration in section 3.3 “Setting of the hardware configu ration”. Also update with the latest BIOS [...]

  • Página 262

    4.12 System board 4 Replacement Procedures M2.5x4B FLAT BIND BATT CONN cover SD board flat cable Insulator DC-IN jack USB harness SVP harness M2.5x4B FLAT BIND Wireless LAN KILL switch Figure 4-24 Removing the system board 4-38 QOSMIO F 10 Maint enance Ma nual (960 -498)[...]

  • Página 263

    4 Replacement Procedures 4.12 System board Installing the system board The following describes the procedure for inst alling the system board (See Figure 4-23 and 4-24). 1. Connect the DC-IN jack, SD board flat cable and SVP harness to the system board. 2. Install the BATT CONN cover with fitting to the slot of th e base assembly. 3. Install the DC[...]

  • Página 264

    4.13 RTC battery 4 Replacement Procedures 4.13 RTC battery Removing the RTC battery The following describes the procedure for removing the RTC battery (See Figure 4-25). 1. Disconnect the RTC battery ha rness from the connector CN 8490 on the system board. 2. Pull out the RTC battery harness from the guide and remo ve the RTC battery . RTC battery [...]

  • Página 265

    4 Replacement Procedures 4.14 TV tuner module/Guide 4.14 TV tuner module/Guide 4.14.1 TV tuner module Removing the TV tuner module The following describes the procedure for remo ving the TV tuner module (See Figure 4-26). 1. Disconnect the TV tuner harness from the connector on the TV tuner module. 2. Disconnect the TV tuner coaxial cable from the [...]

  • Página 266

    4.14 TV tuner module/Guide 4 Replacement Procedures Installing the TV tuner module The following describes the procedure for inst alling the TV tuner module (See Figure 4-26). 1. Insert the TV tuner module terminals slantwise into the connector on the system board and secure it with the following screws. • M2 × 4Z BIND screw x2 2. Connect the TV[...]

  • Página 267

    4 Replacement Procedures 4.14 TV tuner module/Guide USB harness CN9501 TV tuner harness TV tuner coaxial cable M2x4 BIND Guide Figure 4-27 Removing the guide Installing the guide The following describes the procedure for installing the guide (See Figure 4-27). 1. Install the guide on the system board and secure it with the following screw . • M2 [...]

  • Página 268

    4.15 Heat sink/CPU 4 Replacement Procedures 4.15 Heat sink/CPU Removing the heat sink/CPU The following describes the procedure for re m oving the heat sink and CPU (See Figure 4-28 and 4-29). 1. After Removing the following screws, remove the heat sink holder and heat sink . • M2 × 4Z BIND screw x3 M2x4Z BIND Heat sink holde r Heat sink Figure [...]

  • Página 269

    4 Replacement Procedures 4.15 Heat sink/CPU 2. Unlock the CPU by rotating the cam on the CPU socket 180 degrees to the counterclockwise with a flat-blade screwdriver. 3. Remove the CPU. Cam Figure 4-29 Removing the CPU Installing the heat sink/CPU The following describes the procedure for inst alling the heat sink and CPU (See Figure 4-28 to 4-30).[...]

  • Página 270

    4.15 Heat sink/CPU 4 Replacement Procedures NOTE: Apply the silicon grease enough to cover the chip surface using the special applicator. Figure 4-30 Applying silicon grease 5. Install the heat sin k and heat sink holder and secure them with the following screws in the order of numbers mark ed on the heat sink holder. • M2 × 4Z BIND screw x3 4-4[...]

  • Página 271

    4 Replacement Procedures 4.16 VGA Heat sink 4.16 VGA Heat sink Removing the VGA heat sink The following describes the procedure for removing the VGA heat sink (See Figure 4-31). 1. After removing the follo wing screws, remove the VGA heat sink . • M2 × 4Z BIND screw x3 VGA heat sink M2x4Z BIND Figure 4-31 Removing the VGA heat sink Installing th[...]

  • Página 272

    4.17 PC card cover 4 Replacement Procedures 4.17 PC card cover Removing the PC card cover The following describes the procedure for rem o ving the PC card cover (See Figure 4-32). 1. Remove the following screws securing the PC card cover. • M2 × 3Z BIND screw x2 2. Open the PC card cover toward the outside to unlatch it from hooks and pull up th[...]

  • Página 273

    4 Replacement Procedures 4.18 Speaker/VGA fan 4.18 Speaker/VGA fan Removing the Speaker/VGA fan The following describes the procedure for re moving the speaker and VGA fan (See Figure 4- 33). 1. Pull out the speaker cable L (red cable) under the insulator and the glass tapes. 2. Remove the speaker L from the guide of base assem bly. 3. Remove the s[...]

  • Página 274

    4.18 Speaker/VGA fan 4 Replacement Procedures Installing the Speaker/VGA fan The following describes the procedure for inst alling the speaker and VGA fan (See Figure 4- 33). NOTE: When installing speakers , make sure they are fit to the guides closely by pressing them from the top. Pass the VGA fan cable first on the base assembly so that the spea[...]

  • Página 275

    4 Replacement Procedures 4.19 Battery latch 4.19 Battery latch Removing the battery latch The following describes the procedure for rem ovi ng the battery latch (See Figure 4-34 and 3- 35). 1. Remove the following screws fixing the battery latch assembly. • M2 × 4Z FLAT BIND screw x2 2. Slide the battery lock to the arrow direction and pu sh up [...]

  • Página 276

    4.19 Battery latch 4 Replacement Procedu res Installing the battery latch The following describes the procedure for instal ling the battery latch (See Figure 4-34 and 4- 35). 1. Install the battery lock button . 2. Set the spring on the battery latch and install the batte ry latch on the battery latch assembly . Make sure the spring is not set over[...]

  • Página 277

    4 Replacement Procedures 4.20 Touch pad 4.20 Touch pad Removing the touch pad The following describes the procedure for removing the touch pad (See Figure 4-36). 1. Remove the glass tape fixing the touch pad flexible cable. 2. Disconnect the touch pad flat cable from the touch pad. 3. Remove the following screws fixing the touch pad plate and remov[...]

  • Página 278

    4.20 Touch pad 4 Replacement Procedures Installing the touch pad The following describes the procedure for in stalling the touch pad (See F igure 4-36). NOTE : Do not reuse the touch pad so that it c an not be used after peeling off from the computer. Be sure to stick a new touch pad. 1. Stick the touch pad and secure it with the following screw s [...]

  • Página 279

    4 Replacement Procedures 4.21 SJ board 4.21 SJ board Removing the SJ board The following describes the procedure for removing the SJ board (See Figure 4-37). 1. Disconnect the microphone cable from the connector CN6000 on the SJ board. 2. Unlock the connector CN9560 on the SJ board and disconnect the SJ board flat cable from it. 3. Remove the follo[...]

  • Página 280

    4.21 SJ board 4 Replacement Procedu res Installing the SJ board The following describes the procedure for in stalling the SJ board (See Figure 4-37). 1. Pass through the SJ board flat cable into the slit of the middle fram e and arrange it along the guide on the in sulator. Secure the SJ board flat cable with a glass tape. 2. Install the SJ board a[...]

  • Página 281

    4 Replacement Procedures 4.22 Microphone 4.22 Microphone Removing the microphone The following describes the procedure for removing the microphone (See Figure 4-38). 1. Remove the following screw to remove the microphone hold guide from the base assembly. • M2 × 4Z BIND screw x1 2. Detach the microphone from the m icrophone hold guide. 3. Detach[...]

  • Página 282

    4.23 LCD unit/FL inverter 4 Replacement Procedures 4.23 LCD unit/FL inverter Removing the LCD unit/FL inverter The following describes the procedure for removing the LCD unit and FL inverter (See Figure 4-39 to 4-42). 1. Open widely the display panel and pull up both the hinge caps to remove by slightly pressing them toward the display. 2. Peel off[...]

  • Página 283

    4 Replacement Procedures 4.23 LCD unit/FL inverter 4. Remove the following screw fixing the FL inverter. • M2x4Z SUPER THIN HEAD screw x1 5. (for model with wirele ss LAN or Bluetooth) Pull out one insulator and peel off the other one adhered to the FL inverter. 6. Disconnect the LCD harnesses from the connectors CN1 and CN2 on the FL inverter. 7[...]

  • Página 284

    4.23 LCD unit/FL inverter 4 Replacement Procedures 9. Remove the following screws fixing the LCD unit. • M2x4Z SUPER THIN HEAD screw x4 10. W ith the bottom edge of the LCD unit on the display cover, lift onl y the top edge of the LCD unit. After peeling off the aluminum tape , disconnect the LCD harness from the connector on the back of the LCD [...]

  • Página 285

    4 Replacement Procedures 4.23 LCD unit/FL inverter 11. Remove the following screws to remove the right and left L CD supports from the LCD unit. • M2x3C SUPER THIN HEAD screw x4 M2x3C SUPER THIN HEAD LCD supports M2x3C SUPER THIN HEAD Figure 4-42 Removing the LCD supports QOSMIO F 10 Maint enance Ma nual (960 -498) 4-61[...]

  • Página 286

    4.23 LCD unit/FL inverter 4 Replacement Procedures Installing the LCD unit/FL Inverter The following describes the procedure for inst alling the LCD unit and FL inverter (See Figure 4-39 to 4-42). 1. Secure the LCD supports (left and right) to the LCD unit with the following screws . • M2 × 3C SUPER THIN HEAD screw x4 2. Stand the LCD unit on th[...]

  • Página 287

    4 Replacement Procedures 4.24 Wireless antennas/ LCD harness 4.24 Wireless antennas/ LCD harness 4.24.1 Wireless antennas Removing the wireless antennas The following describes the procedure for re m oving the wireless antennas (See Figure 4-44 and 4-44). 1. Make sure the wireless LAN antenna cables are pulled on the middle frame. (Refer to 4.8 Dis[...]

  • Página 288

    4.24 Wireless antennas/ LCD harness 4 Replacement Procedures 3. Peel off the glass tapes fixing the wireless LAN antenna cables and bluetooth antenna cable and peel off the wireless LAN antennas and bluetooth antenna from the display cover. Glass tape Wireless LAN antenna with black cable Bluetooth antenna Glass tape Glass tape Wireless LAN antenna[...]

  • Página 289

    4 Replacement Procedures 4.24 Wireless antennas/ LCD harness 4.24.2 LCD harness Removing the LCD harness The following describes the procedure for remo ving LCD harness (See Figure 4-45 and 4-46). 1. Remove the following screw securing the LCD harness holder and remove the LCD harness holder (display cover side). • M2.5 × 4B FLAT BIND screw x1 M[...]

  • Página 290

    4.24 Wireless antennas/ LCD harness 4 Replacement Procedures 2. Remove the following screw securing the LCD harness holder and remove the LCD harness holder (middle frame side). • M2.5 × 2.8B FLAT BIND screw x1 3. Remove the LCD harness from the guide. M2.5x2.8B FLAT BIND LCD harness holder LCD harness Figure 4-46 Removing the LCD harness holder[...]

  • Página 291

    4 Replacement Procedures 4.25 Hinge 4.25 Hinge Removing the Hinge The following describes the procedure for rem oving hinge (See Figure 4-47 to 4-49). 1. Remove the following screws securing the display cover and detach the display cover . • M2.5 × 6 PSP TIGHT screw x4 M2.5x6 PSP TIGHT Figure 4-47 Removing the display cover QOSMIO F 10 Maint ena[...]

  • Página 292

    4.25 Hinge 4 Replacement Procedures 2. Remove the following screws and remove the hinges (displa y cover side). • M2.5 × 6B FLAT BIND screw x2 ( L o c k t i g h t ) M2.5x6B FLAT BIND (Locktight) Hinges (display cover side) Figure 4-48 Removing the hi nge (display cover side) 3. Remove the following screws and remove the hinges (middle fram e sid[...]

  • Página 293

    4 Replacement Procedures 4.25 Hinge QOSMIO F 10 Maint enance Ma nual (960 -498) 4-69 Installing the Hinge The following describes the procedure for in stalling the hinge (See Figure 4-47 to 4-49). 1. Install the hinges (middle frame side) on the back side of the m iddle frame and secure them with the following screw s . • M2.5 × 4B FLAT BIND scr[...]

  • Página 294

    Appendices[...]

  • Página 295

    Appendices App-ii QOSMIO F10 Maintenance Manual (960- 498)[...]

  • Página 296

    Appendices Appendix Contents Appendix A Handling the LCD Module ......................................................................... A-1 Appendix B Board Layout ............................................................................................... B-1 B.1 System Board Front View ........................................................[...]

  • Página 297

    Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged duri ng assembly or disassembly. Observe the following precautions when handling the LCD module: 1. When installing the LCD module in the LCD cove r, be sure to seat it so that it is properly aligned and maximum visibili ty of [...]

  • Página 298

    Appendix A Handling the LCD Module 3. If the panel’s surface gets dirty, wipe it with co tton or a soft cloth. If it is still dirty, try breathing on the surface to create a light cond ensate and wipe it again. If the surface is very dirty, we recomme nd a CRT cleaning agent. Apply the agent to a cloth and then wipe the panel’s surface. Do not [...]

  • Página 299

    Appendix A Handling the LCD Module 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the m odule, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module. QOSMIO F 10 Maint e[...]

  • Página 300

    Appendix A Handling the LCD Module 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. 9. Do not disassemble the LCD module. Disassembly can cause m [...]

  • Página 301

    Appendix A Handling the LCD Module 10. If you transport the module, do not use pack ing material that c ontains epoxy resin (amine) or silicon glue (alcohol or oxide). These materials can release gas that can damage the panel’s polarization. QOSMIO F 10 Maint enance Ma nual (960- 498) A-5[...]

  • Página 302

    Appendix A Handling the LCD Module A-6 QOSMIO F10 Maintenance Ma nual (960-4 98)[...]

  • Página 303

    Appendices C.18 CN4200 1394 I/F connector (4-pin) .......................................................... C-10 C.19 IS2101 MEDIA BRIDGE I/F connector (42-pin) ................................... C-10 C.20 CN1400 Memory connector A (200-pin) .................................................. C-11 C.21 CN1401 Memory connector B (200-pin) .........[...]

  • Página 304

    Appendices Appendix D Keyboard Scan/Character Codes .............................................................. D-1 Appendix E Key Layout .................................................................................................. E-1 E.1 Keyboard Layout ......................................................................................[...]

  • Página 305

    Appendices Figures Figure B-1 System board layout (front) .......................................................................... B-1 Figure B-2 System board layout (back) .......................................................................... B-3 Figure B-3 SD board layout (front) .............................................................[...]

  • Página 306

    Appendices Table C-10 USB connector 0 (port 0) (4-pin) .................................................................. C-6 Table C-11 USB I/F Relay connector (8-pin) .................................................................. C-7 Table C-12 USB connector 1 (port 2) (4-pin) ..................................................................[...]

  • Página 307

    Appendices App-viii QOSMIO F10 Maintenance Manua l (960-498) Table C-42 TV-tuner co nnector (12-pin) ....................................................................... C-29 Table C-43 SVP connector (14-pin) .............................................................................. C-29 Table C-44 Internal Microphone I/F connector (2-pin) .[...]

  • Página 308

    Appendix B Appendix B Board Layout B.1 System Board Front View (e) (b) (c) (a) (d) (p) (f) (o) (g) (n) (h) (i) (j) (m) (l) (k) Figure B-1 System board layout (front) QOSMIO F 10 Maint enance Ma nual (960- 498) B-1[...]

  • Página 309

    B.1 System Board Front View Appendix B Board Layout Table B-1 System board ICs and connectors (front) Mark Number Name (a) CN5801 TV Input connector (b) CN9500 SD board I/F connector (c) CN9650 SWITCH I/F connec tor (d) CN3230 Keyboard I/F con nector (e) CN3201 PAD I/F connector (f) CN2200 Mini PCI I/F connector (g) CN4400 Bluetooth I/F connector ([...]

  • Página 310

    Appendix B Board Layout B.2 System Board Back View B.2 System Board Back View (e) (b) (c) (d) (a) (f) (g) (h) (r) (i) (j) (q) (k) (l) (m) (p) (o) Figure B-2 System board layout (back) (n) QOSMIO F 10 Maint enance Ma nual (960- 498) B-3[...]

  • Página 311

    B.2 System Board Back View Appendix B Board Layout Table B-2 System board ICs and connectors (back) Mark Number Name (a) CN8810 1st battery connector (b) CN8490 RTC battery connector (c) CN1820 ODD I/F connector (d) CN8800 DC IN connector (e) IC5800 SVP MEM I/F (f) CN5502 D-video I/F connector (g) CN5501 S-video I/F connector (h) CN4612 USB I/F Rel[...]

  • Página 312

    Appendix B Board Layout B.3 SD Board Front View B.3 SD Board Front View ( f ) (g) ( e ) ( d ) ( c ) ( b ) ( a ) ( h ) ( i ) ( l ) ( k ) (j) Figure B-3 SD board layout (front) Table B-3 SD board connectors (front) Mark Number Name (a) CN4621 USB I/F connector (b) CN4620 USB I/F relay connector (c) CN6003 Speaker (right) connector (d) CN6002 Spea ker[...]

  • Página 313

    B.4 SD Board Back View Appendix B Board Layout B.4 SD Board Back View (a) Figure B-4 SD board layout (back) Table B-4 SD board connectors (back) Mark Number Name (a) CN3000 MDC I/F connector B-6 QOSMIO F10 Maint enance Ma nual (960- 498)[...]

  • Página 314

    Appendix B Board Layout B.5 SJ Board Front View B.5 SJ Board Front View (b) (a) Figure B-5 SJ board layout (front) Table B-5 SJ board connectors (front) Mark Number Name (a) DS6000 Headphone connector (b) J6001 External Microphone I/F co nnector QOSMIO F 10 Maint enance Ma nual (960- 498) B-7[...]

  • Página 315

    B.6 SJ Board Back View Appendix B Board Layout B-8 QOSMIO F10 Maint enance Ma nual (960- 498) B.6 SJ Board Back View (a) (b) Figure B-6 SJ board layout (back) Table B-6 SJ board connectors (back) Mark Number Name (a) CN6000 Internal microphone connector (b) CN9560 SD board I/F conne ctor[...]

  • Página 316

    Appendix C Appendix C Pin Assignment System Board (FCLSY*) C.1 CN1800 HDD I/ F connector (44-pin) Table C-1 HDD I/F connector (44-pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 IDRSTA-P5N I/O 2 GND - 3 PDD07-P3P I/O 4 PDD08-P3P I/O 5 PDD06-P3P I/O 6 PDD09-P3P I/O 7 PDD05-P3P I/O 8 PDD10-P3P I/O 9 PDD04-P3P I/O 10 PDD11-P3P I/O 11 PDD03-P3P [...]

  • Página 317

    C.2 CN1820 ODD I/F connector (50-pi n) Appendix C Pin Assignment C.2 CN1820 ODD I/F connector (50-pin) Table C-2 ODD I/F connector (50-pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 CDAUDL-PXP I 2 CDAUDR- PXP I 3 CD-GND I 4 N.C - 5 IDRSTB-P5N O 6 SDD08-P3P I/O 7 SDD07-P3P I/O 8 SDD09-P3P I/O 9 SDD06-P3P I/O 10 SDD10-P3P I/O 11 SDD05-P3P I/O[...]

  • Página 318

    Appendix C Pin Assignment C.3 CN2110 PC card I/F connector (70-pin) C.3 CN2110 PC card I/F connector (70-pin) Table C-3 PC card I/F connector (70-pin) (1/2) PIN No. Signal name I/O PIN No. Signal name I/O 1 GND - 2 ACAD0 0-EYP I/O 3 ACAD01-EYP I/O 4 ACAD03-EYP I/O 5 ACAD05-EYP I/O 6 ACAD07-EY P I/O 7 ACCBEO-EYN I/O 8 ACAD09-EYP I/O 9 ACAD11-EYP I/O[...]

  • Página 319

    C.4 CN3230 Keyboard I/F connector (34- pin) Appendix C Pin Assignment Table C-3 PC card I/F connector (70-pin) (2/2) PIN No. Signal name I/O PIN No. Signal name I/O 51 MCVCCA-EYV I 52 MCVPPA-EYV I/O 53 ACTRDY-EYN I/O 54 ACFRAM-EYN I/O 55 ACAD17-EYP I/O 56 ACAD19-EYP I/O 57 ACVS2-E3P I/O 58 ACRST-EYN I/O 59 ACSERR-EYN I/O 60 ACREQ-EYN I/O 61 ACCBE3-[...]

  • Página 320

    Appendix C Pin Assignment C.5 CN4400 Bluetooth I/F connector (20-pin) C.5 CN4400 Bluetooth I/F connector (20-pin) Table C-5 Bluetooth I/ F connector (20-pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 GND - 2 N.C. - 3 BTMDL-P3N O 4 N.C. - 5 N.C. - 6 N.C. - 7 N.C. - 8 BTRST-S3N I 9 N.C. - 10 N.C. - 11 GND - 12 N.C. - 13 GND - 14 WCHCLK- P3P O[...]

  • Página 321

    C.8 CN8770 FAN connector (3-pin) Appendix C Pin Assignment C.8 CN8770 FAN connector (3-pin) Table C-8 FAN connector (3-pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 FAN VCC I 2 GND - 3 FANG0-P3P I C.9 CN8780 FAN connector (for VGA) (3-pin) Table C-9 FAN connector (for VGA) (3-pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 FAN VCC ([...]

  • Página 322

    Appendix C Pin Assignment C.11 CN4612 USB I/F Relay connector (8-pin) C.11 CN4612 USB I/F Relay connector (8-pin) Table C-11 USB I/F Relay connector (8-pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 USB1PS-E5V I 2 USB1PS-E5V I 3 USBP4-S3N I/O 4 USBP4-S3P I/O 5 GND - 6 GND - 7 GND - 8 N.C. - C.12 CN4630 USB connector 1 (port 2) (4-pin) Table[...]

  • Página 323

    C.15 CN9500 Sound board I/F connector (50-pin) Appendix C Pin Assignment C.15 CN9500 Sound boar d I/F connector (50-pin) Table C-15 Sound board I/F connector (50-pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 CD-GND - 2 CDAUDL-PXP I 3 CD-GND - 4 CDAUDR-PXP I/O 5 CD-GND - 6 SND-GND - 7 SND-GND - 8 SND-GND - 9 SND-GND - 10 SND-GND - 11 ATBEEP[...]

  • Página 324

    Appendix C Pin Assignment C.16 CN9650 SWITCH I/F connector (20-pin) C.16 CN9650 SWITCH I/F connector (20-pin) Table C-16 SWITCH I/F connector (20-pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 PBLEDO-S3P I 2 M5V - 3 PBLEDB-S3P I 4 PBLEDG-S3P I 5 PWRSW-S3N I 6 TVBTN-S3N I 7 CDBTN-S3N I 8 GND - 9 GND - 10 KBRT00-S3N I 11 KBRT01-S3N I 12 KBRT0[...]

  • Página 325

    C.18 CN4200 1394 I/F connector (4-p in) Appendix C Pin Assignment C.18 CN4200 1394 I/F connector (4-pin) Table C-18 1394 I/F connector (4-pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 TPB0-E3N I/O 2 TPB0-E3P I/O 3 TPA0-E3N I/O 4 TPA0-E3P I/O C.19 IS2101 MEDIA BRIDGE I/F connector (42-pin) Table C-19 MEDIA BRIDGE I/F connector (42-pin) PIN [...]

  • Página 326

    Appendix C Pin Assignment C.20 CN1400 Memory connector A (200-pin) C.20 CN1400 Memory connector A (200-pin) Table C-20 Memory connector A (200-pin) (1/3) PIN No. Signal name I/O PIN No. Signal name I/O 1 MR1R25-B1V - 2 MRVREF-B1V - 3 GND - 4 GND - 5 SDQ00-B2P I/O 6 SDQ06-B2P I/O 7 SDQ04-B2P I/O 8 SDQ01-B2P I/O 9 2R5-B2V - 10 2R5-B2 V - 11 SDQS0-B2P[...]

  • Página 327

    C.20 CN1400 Memory connector A (200- pin) Appendix C Pin Assignment Table C-20 Memory connector A (200-pin) (2/3) PIN No. Signal name I/O PIN No. Signal name I/O 65 SDQ26-B2P I/O 66 SDQ30-B2P I/O 67 SDQ27-B2P I/O 68 SDQ31-B2P I/O 69 2R5-B2V - 70 2R5-B2V - 71 SCB5A-B2P I/O 72 SCB0A-B2P I/O 73 SCB4A-B2P I/O 74 SCB1A-B2P I/O 75 GND - 76 GND - 77 SDQS8[...]

  • Página 328

    Appendix C Pin Assignment C.20 CN1400 Memory connector A (200-pin) Table C-20 Memory connector A (200-pin) (3/3) PIN No. Signal name I/O PIN No. Signal name I/O 135 SDQ34-B2P I/O 136 SDQ39-B2P I/O 137 GND - 138 GND - 139 SDQ38-B2P I/O 140 SDQ35-B2P I/O 141 SDQ44-B2P I/O 142 SDQ41-B2P I/O 143 2R5-B2V - 144 2R5-B2V - 145 SDQ45-B2P I/O 146 SDQ40-B2P I[...]

  • Página 329

    C.21 CN1401 Memory connector B (200- pin) Appendix C Pin Assignment C.21 CN1401 Memory connector B (200-pin) Table C-21 Memory connector B (200-pin) (1/3) PIN No. Signal name PIN No. Signal name I/O 1 MRVREF-B1V 2 MRVREF-B1V - 3 GND I/O - - 4 GND - 5 SDQ00-B2P I/O 6 I/O 7 SDQ04-B2P I/O 8 I/O 9 2R5-B2V - 10 SDQ06-B2P SDQ01-B2P 2R5-B2V - 11 SDQS0-B2P[...]

  • Página 330

    Appendix C Pin Assignment C.21 CN1401 Memory connector B (200-pin) Table C-21 Memory connector B (200-pin) (2/3) PIN No. Signal name I/O PIN No. Signal name I/O 63 GND - 64 GND - 65 SDQ26-B2P I/O 66 SDQ30-B2P I/O 67 SDQ27-B2P I/O 68 SDQ31-B2P I/O 69 2R5-B2V - 70 2R5-B2V - 71 SCB5B-B2P I/O 72 SCB0B-B2P I/O 73 SCB4B-B2P I/O 74 SCB1B-B2P I/O 75 GND - [...]

  • Página 331

    C.21 CN1401 Memory connector B (200- pin) Appendix C Pin Assignment Table C-21 Memory connector B (200-pin) (3/3) PIN No. Signal name I/O PIN No. Signal name I/O 135 SDQ34-B2P I/O 136 SDQ39-B2P I/O 137 GND - 138 GND - 139 SDQ38-B2P I/O 140 SDQ35-B2P I/O 141 SDQ44-B2P I/O 142 SDQ41-B2P I/O 143 2R5-B2V - 144 2R5-B2 V - 145 SDQ45-B2P I/O 146 SDQ40-B2P[...]

  • Página 332

    Appendix C Pin Assignment C.22 CN2200 Mini PCI I/F connector (124-pin) C.22 CN2200 Mini PCI I/F connector (124-pin) Table C-22 Mini PCI I/F c onnector (124-pin) (1/2) PIN No. Signal name I/O PIN No. Signal name I/O 1 N.C. - 2 N.C. - 3 N.C. - 4 N.C. - 5 N.C. - 6 N.C. - 7 N.C. - 8 N.C. - 9 N.C. - 10 N.C. - 11 N.C. - 12 N.C. - 13 WLON-S5N I 14 N.C. - [...]

  • Página 333

    C.22 CN2200 Mini PCI I/F connector ( 124-pin) Appendix C Pin Assignment Table C-22 Mini PCI I/ F connector (124-pin)(2/2) PIN No. Signal name I/O PIN No. Signal name I/O 61 IRDY-P3N I/O 62 GND - 63 P3V - 64 FRAME-P3N I/O 65 CLKRUN-P3N I/O 66 TRDY-P3N I/O 67 SERR-P3N I 68 STOP-P3N I/O 69 GND - 70 P3V - 71 PERR-P3N I/O 72 DEVSEL-P3N I/0 73 CBE1-P3N I[...]

  • Página 334

    Appendix C Pin Assignment C.23 CN2400 WW Tuner I/F connector (124-pin) C.23 CN2400 WW Tuner I/F connector (124-pin) Table C-23 WW Tuner I/F connector (124-pin) (1/2) PIN No. Signal name I/O PIN No. Signal name I/O 1 N.C. - 2 N.C. - 3 N.C. - 4 N.C. - 5 N.C. - 6 N.C. - 7 N.C. - 8 N.C. - 9 GND - 10 GND - 11 N.C. - 12 N.C. - 13 N.C. - 14 N.C. - 15 GND [...]

  • Página 335

    C.23 CN2400 WW Tuner I/F connector ( 124-pin) Appendix C Pin Assignment Table C-23 WW Tuner I/F connector (124-pin)(2/2) PIN No. Signal name I/O PIN No. Signal name I/O 63 T-P3V - 64 FRAME-P3N I/O 65 CLKRUN-P3N I/O 66 TRDY-P3N I/O 67 SERR-P3N I 68 STOP-P3N I/O 69 GND - 70 T-P3V - 71 PERR-P3N I/O 72 DEVSEL-P3N I/0 73 CBE1-P3N I/O 74 GND - 75 AD14-P3[...]

  • Página 336

    Appendix C Pin Assignment C.24 CN3201 PAD I/F connector (4-pin) C.24 CN3201 PAD I/F connector (4-pin) Table C-24 PAD I/F connector (4-pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 GND - 2 IPDCLK-P5P I/O 3 IPDDAT-P5P I/O 4 GND - C.25 PJ5600 LCD I/F connector (41-pin) Table C-25 LCD I/F connector (41-pin) PIN No. Signal name I/O PIN No. Sign[...]

  • Página 337

    C.26 CN5080 CRT I/F connector (15- pin) Appendix C Pin Assignment C.26 CN5080 CRT I/F connector (15-pin) Table C-26 CRT I/F connector (15-pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 CRTRED-PXP I 2 CRTG RN- PXP I 3 CRTBLU-PXP I 4 N.C - 5 GND - 6 GND - 7 GND - 8 GND - 9 DDC-P5V I 10 GND - 11 N.C - 12 NVDSDA-P5P I/O 13 (AHSYNC- P3P) O 14 (A[...]

  • Página 338

    Appendix C Pin Assignment C.29 CN5502 D-video I/F connector (14-pin) C.29 CN5502 D-video I/F connector (14-pin) Table C-29 D-video I/F connector (14-pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 HDTVY-PXP I 2 GND - 3 HDTVPB-PXP I 4 GND - 5 HDTVPR-PXP I 6 GND - 7 LINOTL-PXP I 8 (LINE1) I/O 9 (LINE2) I/O 10 LINOTR-PXP I 11 (LINE3) I/O 12 GND[...]

  • Página 339

    C.31 CN3000 MDC I/F connector (30- pin) Appendix C Pin Assignment SD Board (FCLSD*) C.31 CN3000 MDC I/F connector (30-pin) Table C-31 MDC I/F connector (30-pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 N.C - 2 GND - 3 GND - 4 N.C - 5 N.C - 6 N.C - 7 N.C - 8 GND - 9 N.C - 10 N.C - 11 N.C - 12 N.C - 13 N.C - 14 N.C - 15 GND - 16 E3V - 17 E3V[...]

  • Página 340

    Appendix C Pin Assignment C.33 CN4621 USB I/F connector (port 4) (4-pin) C.33 CN4621 USB I/F connector (port 4) (4-pin) Table C-33 USB I/F connector (port 4) (4-pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 (USBV) - 2 (D-0) I/O 3 (D+0) I/O 4 GND - C.34 CN6002 Speaker (left) connector (3-pin) Table C-34 Speaker (left) connector (3-pin) PIN [...]

  • Página 341

    C.36 CN9550 Sound jack board I/F connector (21-pin) Appendix C Pin Assignment C.36 CN9550 Sound jack board I/F connector (21-pin) Table C-36 Sound jack board I/F connector (21-pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 VREF1-P2V I 2 MICIN-PXP I 3 LOUTL-PXP I 4 A-GND - 5 LOUTR-PXP I 6 A-GND - 7 VOLOL-PXP I 8 A-GND - 9 VOLOR-PXP I 10 A-GN[...]

  • Página 342

    Appendix C Pin Assignment C.37 CN9510 System boar d I/F connector (50-pin) C.37 CN9510 System board I/F connector (50-pin) Table C-37 System board I/F connector (50-pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 SPKON-P3N - 2 VOLBYP-P3N I/O 3 FMTST0-P3P I 4 SVSDA-P3P I/O 5 SVSCL-P3P I/O 6 GND - 7 SUSCLK-P3P O 8 GND - 9 M97IN2-E3P I 10 GND -[...]

  • Página 343

    C.38 J2410 TV Antenna connector (4-p in) Appendix C Pin Assignment C.38 J2410 TV Antenna connector (4-pin) Table C-38 TV antenna connector (4-pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 (CN9 611-3) I/O 2 (CN9611-1) I/O 3 (CN9 611-2) I/O 4 (CN9611-4) I/O C.39 CN2410 Coaxial connector (4-pin) Table C-39 Coaxial connector (4-pin) PIN No. Si[...]

  • Página 344

    Appendix C Pin Assignment C.42 CN9614 TV-tuner connector (12-pin) C.42 CN9614 TV-tuner connector (12-pin) Table C-42 TV-tuner connector (12-pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 TV-GND - 2 LINL-PXP I 3 TV-GND - 4 LINR-PXP I 5 TV-GND - 6 COMP01-PXP I 7 TV-GND - 8 LUMA01-PXP I 9 TV-GND - 10 CROM01-PXP I 11 TV-GND - 12 TV-GND - C.43 C[...]

  • Página 345

    C.44 CN6000 Internal Microphone I/F connect or (2-pin) Appendix C Pin Assignment SJ board (FCLSJ*) C.44 CN6000 Internal Microp hone I/F connector (2-pin) Table C-44 Internal Microphone I/F connector (2-pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 (VREF1-P2V) I 2 A-GND - C.45 J6001 External Microp hone I/F connector (6-pin) Table C-45 Exte[...]

  • Página 346

    Appendix C Pin Assignment C.47 CN9560 Sound boar d I/F connector (21-pin) C.47 CN9560 Sound boar d I/F connector (21-pin) Table C-47 Sound board I/F connector (21-pin) PIN No. Signal name I/O PIN No. Signal name I/O 1 VREF1-P2V O 2 MICIN-PXP O 3 LOUTL-PXP O 4 A-GND - 5 LOUTR-PXP O 6 A-GND - 7 VOLOL-PXP O 8 A-GND - 9 VOLOR-PXP O 10 A-GND - 11 HEADL-[...]

  • Página 347

    C.47 CN9560 Sound board I/F connector (21-pin) Appendix C Pin Assignment C-32 QOSMIO F10 Mainten ance Manu al (960- 498)[...]

  • Página 348

    Appendix D Keyboard S can/Character Codes Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 01 ‘ ~ 29 A9 0E F0 0E 02 1 ! 02 82 16 F0 16 03 2 @ 03 83 1E F0 1E 04 3 # 04 84 26 F0 26 05 4 $ 05 85 25 F0 25 06 5 % 06 86 2E F0 2E 07 6 ^ 07 87 36 F0 36 08[...]

  • Página 349

    Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 29 | 2B AB 5D F0 5D *5 30 Caps Lo ck 3A BA 58 F0 58 31 A 1E 9E 1C F0 1C 32 S 1F 9F 1B F0 1B 33 D 20 A0 23 F0 23 34 F 21 A1 2B F0 2B 35 G 22 A2 34 F0 34 36 H 23 A3 33 F0 33 37 J 24 A4 3B F0 3B *2 38 [...]

  • Página 350

    Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 58 Ctrl 1D 9D 14 F0 14 *3 60 Alt (L) 38 B8 11 F0 11 *3 61 Space 39 B9 29 F0 29 62 ALT (R) E0 38 E0 B8 E0 11 E0 F0 11 75 Ins E0 52 E0 D2 E0 70 E0 F0 70 *1 76 Del E0 53 E0 D3 E0 71 E0 F0 71 *1 79 ← E0[...]

  • Página 351

    Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (4/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 07 F0 07 *3 124 PrintSc *6 *6 *6 *6 *6 126 Pause *7 *7 *7 *7 *7 202 Fn — — — — *4 203 Win E0 5B E0 DB E0 1F E0 F0 1F 204 App E0 5D E0 DD E0 2F E0 F0 2F [...]

  • Página 352

    Appendix D Keyboard Scan/Character Codes Table D-2 Scan codes with left Shift key Code set 1 Code set 2 Cap No. Key top Make Break Make Break 55 / E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12 75 INS E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0 12 76 DEL E0 AA E0 53 E0 D3 E0 2A E0 F0 12 E0 71 E0 F0 71 E0 12 79 ← E0 AA E0 4B E0 CB E0[...]

  • Página 353

    Appendix D Keyboard Scan/Character Codes Table D-3 Scan codes in Numlock mode Code set 1 Code set 2 Cap No. Key top Make Break Make Break 75 INS E0 2A E0 52 E0 D2 E0 AA E0 12 E0 70 E0 F0 70 E0 F0 12 76 DEL E0 2A E0 53 E0 D3 E0 AA E0 12 E0 71 E0 F0 71 E0 F0 12 79 ← E0 2A E0 4B E0 CB E0 AA E0 12 E0 6B E0 F0 6B E0 F0 12 80 Home E0 2A E0 47 E0 C7 E0 [...]

  • Página 354

    Appendix D Keyboard Scan/Character Codes Table D-5 Scan codes in overlay mode Code set 1 Code set 2 Cap No. Keytop Make Break Make Break 09 8 (8) 48 C8 75 F0 75 10 9 (9) 49 C9 7D F0 7D 11 0 (*) 37 B7 7C F0 7C 23 U (4) 4B CB 6B F0 6B 24 I (5) 4C CC 73 F0 73 25 O (6) 4D CD 74 F0 74 26 P (–) 4A CA 7B F0 7B 37 J (1) 4F CF 69 F0 69 38 K (2) 50 D0 72 F[...]

  • Página 355

    Appendix D Keyboard Scan/Character Codes D-8 QOSMIO F 10 Mainte nance Manu al (960- 498) Table D-7 No.126 key scan code Code set 1 Code set 2 Key top Shift Make Make Pause Co m mo n * E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14 F0 77 Ctrl* E0 46 E0 C6 E0 7E E0 F0 7E *: This key generates only make codes.[...]

  • Página 356

    Appendix E Key Layout Appendix E Key Layout E.1 Keyboard La yout Figure E-1 Keyboard layout (for US) Figure E-2 Keyboard layout (for UK) QOSMIO F 10 Maint enance Ma nual (960- 498) E-1[...]

  • Página 357

    E.1 Keyboard Layout Appendix E Key Layout E-2 QOSMIO F10 Mai ntenance Manual (9 60-498)[...]

  • Página 358

    Appendix F Appendix F Wiring Diagrams F.1 LAN Loopback Connector (1) BIBAP ‘ (TX + ) ( 2 ) BIDA N (TX -) (3) BIDBP (RX+ ) (4) BIDBN (RX-) Figure F-1 LAN loopback connector QOSMIO F 10 Maint enance Ma nual (960- 498) F-1[...]

  • Página 359

    F.1 LAN Loopback Connector A ppendix F Wiring Diagrams F-2 QOSMIO F10 Mai ntenance Manual (9 60-498)[...]

  • Página 360

    Appendix G Appendix G BIOS Rewrite Procedures This Appendix explains how to rewrite th e system BIOS program when you update the system BIOS. Tools To rewrite the BIOS, you need the following tool:  BIOS/EC/KBC rewriting disk Rewriting the BIOS NOTE: 1. Connect the AC adapter to the co mputer when you rewrite the BIOS. 2. Do not turn off the pow[...]

  • Página 361

    Appendix G BIOS Rewrite Procedures G-2 QOSMIO F10 Maintena nce Manual (960- 498)[...]

  • Página 362

    Appendix H Appendix H EC/KBC Rewrite Procedures This Appendix explains how to rewrite th e EC/KBC system program when you update the EC/KBC system. Tools To rewrite the EC/KBC, you need the following tool:  EC/KBC rewriting disk for the computer Rewriting the EC/KBC NOTE: 1. Rewrite the EC/KBS only when inst ructed by a diagnostic disk release n[...]

  • Página 363

    Appendix H EC/KBC Rewrite Procedures H-2 QOSMIO F10 Maintena nce Manual (960- 498)[...]

  • Página 364

    Appendix I Reliability Appendix I Reliability The following table shows MTBF (Mean Time Between Failures) in maximum configuration . Table I-1 MTBF Component Time (hours) System 5,277 QOSMIO F 10 Maint enance Ma nual (960 -498) I-1[...]

  • Página 365

    Appendix I Reliability I-2 QOSMIO F 10 Maint enance Ma nual (960 -498)[...]