Perlick H50IMS-R manual

MODELS: H50IMS-R H50IMS-L H50IMW H50IMS-ADL H50IMS-ADR H50IMW-AD PERLICK SELF-CONTAINED ICE MAKER P R O D U C T M A N U A L Issued: 11-2-2009[...]

2 IMPORTANT This manual should be read carefully before the icemaker is installed and operated. Only qualied service technicians should install, service, and maintain the icemaker. Read the warnings contained in this booklet carefully as they give important information regarding safety. Please retain this booklet for any further reference that m[...]

3 Important Safety Information Throughout this manual, notices appear to bring your attention to situations which could result in death, serious injury, or damage to the unit. WARNING Indicates a hazardous situation which could result in death or serious injury. CAUTION Indicates a situation which could result in damage to the unit. IMPORTANT Indic[...]

4 I. Specications A. Construction Top Panel Ice Making Mechanism Scoop Holder Front Panel Control Switch Louver Bin Control Thermostat Bulb Slope Magnet Catch Door Power Cord[...]

5 PERLICK ICE MAKER MODEL NUMBER H50IMS-R SERIAL NUMBER AC SUPPLY VOLTAGE 115-120/60/1 AMPERES 3.4 AMPS DESIGN PRESSURE HI-240PSI LO-120PSI REFRIGERANT 134a 4.2 oz. B. Nameplate Rating See the nameplate for electrical and refrigeration specications. This nameplate is located inside the bin on the right side. We reserve the right to make changes [...]

6 Units: mm [in.] C. Dimensions/Connections 1. H50IMS-R, H-50IMS-L[...]

7 2. H50IMW Units: mm [in.][...]

8 3. H50IMS-ADL, H50IMS-ADR Units: mm [in.][...]

9 4. H50IMW-AD Units: mm [in.][...]

10 II. Installation and Operating Instructions WARNING 1. This icemaker must be installed in accordance with applicable national, state, and local regulations. 2. CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fallen into the storage bin. A. Checks Before Installa[...]

11 2. Built-In Installation Site CAUTION 1. Do not let the weight of the counter rest on the icemaker. 2. Do not install the icemaker in a corner where the door will interfere with other equipment or where the icemaker cannot be pulled out for service. Installation Space Model Height Width Depth H50IMS-R/L H50IMW 34" (864 mm) minimum 15" [...]

12 1 2 3 4 6 5 C. D oo r Ov er la y P an el F ab ri ca ti o n an d At ta ch me nt (H 50 IM W, H 50 IM W- AD) IMPORTANT The overlay panel must be crafted by a professional cabinet maker to ensure quality results. (1) Parts Ensure that all parts required for the overlay panel assembly are contained in the accessories bag. Overlay Panel Parts No. Desc[...]

13                     (2) Overlay Panel Specification Use the specication that applies to your icemaker (H50IMW or H50IMW-AD) and the directions that follow to prepare your overlay panel. (a) H50IMW H50IMW Overlay Panel Specication Overlay Panel Height 29 17/32" (750 mm) Overla[...]

14                     H50IMW-AD Overlay Panel Specication Overlay Panel Height 27 9/16" (700 mm) Overlay Panel Width 14 13/16" (376 mm) Overlay Panel Thickness 5/8" (16 mm) minimum; 3/4" (19 mm) maximum Overlay Panel and Door Weight (total) 20 lb. (9 kg) maximum (b)[...]

15 3) Screw the 6 threaded wood inserts into the 1/4" holes drilled in the previous step. Make sure that the inserts are threaded straight and that the tops of the inserts are ush to the overlay panel surface. Otherwise, the overlay panel cannot be properly fastened to the door. 4) Mount the door handle hardware. Perlick recommends that the[...]

16 Screws f) Remove hinge (C1) from the top right part of the door, ip it and reattach to the bottom left. Remove hinge (C2) from the bottom right part of the door, ip it and reattach to the top left. See Fig. 8. Proceed to step 7. d) Remove hinge (B) from the right side of the unit and the 2 ller screws from the left side. Attach the 2 ?[...]

17 9) Temporarily fasten the overlay panel to the door using 2 of the M4×25 pan head screws provided. See Fig. 11. CAUTION Ensure that the back surface of overlay panel is at before attaching. 10) Mark the centerpoint of the hinge (C1) and hinge (C2) holes that extend over the overlay panel. See Fig. 12. 7) Remove the bushings from hinge (C1) a[...]

18 Snug the screws, but do not tighten. Sheet Metal Bracket Overlay Panel Tighten the screws. 5) Fasten the overlay panel to the door using the four M4×25 pan head screws provided. Snug the screws, but do not tighten. See Fig. 17. 6) Fasten the sheet metal bracket to the bottom of the door with the three T2 screws provided. Tighten the screws to t[...]

19 7) Tighten the four M4×25 pan head screws installed in step 5. See Fig. 19. 8) Replace the door gasket in its proper orientation. Reinsert the bushings into hinge (C1) and hinge (C2) (the hinges attached to the door). See Fig. 20. Canoe Clips Fig. 19 Tighten the screws. Bushing Bushing Gasket Fig. 20 9) Attach the door to hinge (A), then contin[...]

20 D. Setup 1) Position the icemaker in the selected permanent location. 2) Level the icemaker from side-to-side and front-to-rear by adjusting the feet. E. Electrical Connection WARNING 1. Electrical connection must meet national, state, and local electrical code requirements. Failure to meet these code requirements could result in death, electric[...]

21 F. Water Supply and Drain Connections WARNING 1. Water supply and drain connections must be installed in accordance with applicable national, state, and local regulations. 2. Normal operating water temperature should be within 45°F to 95°F (7°C to 35°C). Operation of the icemaker, for extended periods, outside of this normal temperature rang[...]

22 G. Final Checklist WARNING CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fallen into the storage bin. 1) Is the icemaker level? 2) Is the icemaker in a site where the ambient temperature is within 45°F to 100°F (7°C to 38°C) and the water temperature withi[...]

23 H. Startup WARNING 1. All parts are factory-adjusted. Improper adjustments may adversely affect safety, performance, component life, and warranty coverage. 2. If the icemaker is turned off, wait for at least 3 minutes before restarting the icemaker to prevent damage to the compressor. 3. At startup, conrm that all internal and external connec[...]

24 III. Cleaning and Maintenance WARNING 1. CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after any cleaning or maintenance is done to the unit. Make sure that none have fallen into the storage bin. 2. The storage bin is for ice use only. Do not store anything else in the storage bin. 3. Keep the area aroun[...]

25 3) Inside the storage bin, disconnect the suction tube by squeezing the tabs and pulling the tube clear. See Fig. 26. Allow the water tank to drain. 4) Reconnect the suction tube as illustrated. See Fig. 27. Make sure the tabs lock into place; a loose tting may cause a water leak. 5) Slowly pour the cleaning solution into the water tank. 6) M[...]

26 3. Sanitizing Solution IMPORTANT For safety and maximum effectiveness, use the solution immediately after dilution. Dilute 0.5 . oz. (14.8 ml or 1 tbs) of a 5.25% sodium hypochlorite solution (chlorine bleach) with 1 gallon (3.8 l) of warm water. This is a minimum amount. Make more solution if necessary. Using a chlorine test strip or other m[...]

27 Reducing Pipe Rail Rail 13) Position and lock the ice chute onto the front and rear frame pipes by pushing the ice chute down until it clicks onto both frame pipes. See Fig. 36. 14) Slide in the water tank along the rails at the bottom of the left and right brackets until it locks into place. See Fig. 37. Right Bracket Rail Rail Fig. 34 Fig. 35 [...]

28 15) Reconnect the suction tube. 16) Hook each separator onto the rail, then pull it hard towards you until it locks into place. See Fig. 38. 17) Replace the slope in its correct position. See Fig. 39. Fig. 38 18) Discard the sanitizing solution. 19) Mix a new batch of the sanitizing solution and slowly pour it into the water tank. 20) Move the c[...]

29 B. Maintenance IMPORTANT This icemaker must be maintained individually, referring to the instruction manual and labels provided with the icemaker. 1. Stainless Steel Exterior To prevent corrosion, wipe the exterior occasionally with a clean and soft cloth. Use a damp cloth containing a neutral cleaner to wipe off oil or dirt build up. 2. Storage[...]

30 C. Preparing the Icemaker for Long Storage CAUTION When storing the icemaker for an extended time or in sub-freezing temperatures, follow the instructions below to prevent damage. When the icemaker is not used for two or three days under normal conditions, it is sufcient to move the control switch to the "OFF" position. When storing[...]

31        Full One Year Warranty:  one year      ?[...]