Omron V720-HS04 manual

Electromagnetic Inductive RFID System V720-series User’s Manual Long-Range Antenna V720-HS04 Manual Number SRFM-006A[...]

ii About this Manual: Thank you for purchasing our V720 -seri es Electromagnetic Inductive RFID Syste m. The V720-series is a family of products t hat we re developed by fully utilizing our high technol ogy and broad experience. This Users Manual provide s vario us info rmation that will be necessary when usi ng the V720-HS04 Antenna (hereinafter c[...]

iii Application Con siderations < SUITABILITY F OR USE > OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of the products in the customer's application or use of the products. At the customer's request, OMRON will provide applicable third party certification docume[...]

iv when significant construction changes are made. However, some specificat ions of the products may be changed w ithout any notice. When in doubt, spec ial mode l numbers may be assigned to fix or establish key specifications for your application on your request. Please consult with your OMRON representat ive at any time to confirm actual specific[...]

v Safety Precautions This chapter provides important information for the safe use of this product. Ensure to read the inform ation carefully before us e. In the safety precautions below, severity is categorized as either ”WARNING” or “CAUTION”. WARNING Indicates a potentially hazardous si tuation which, if not avoided, could result in minor[...]

vi 警 WARNING Never disassemble, repair, or modify the main unit and cables. z Do not disassemble, repair, o r modify this product. Doing so may result in el ectric shock, fire, or personal injury. Do not handle the device with wet hands . Do not touch the terminals while the device is connected to the power sup ply. z Electric shock hazard. Do no[...]

vii ・ Locations where the Reader/Writer is exposed to dust, corrosive gas, saline, or flammable gas. ・ Locations where the Reader/Writer is exposed to direct heat. ・ Locations subject to condensa tion due to high humidity. ・ Locations subject to vibr ation or impac t that exceed the lim its outlined in the specifications. ・ Locations wher[...]

viii Precautions This chapter provides important information for interna tional standards and copyright. Ensure to read the inform ation carefully before u se. V720-HS04 conf orms to the foll owing laws and standards. T his conformity is effective on ly if V720-HS04 is used with the designated R eader/W riter, V720-BC5D 4A or V720-BC5D4A-US. 1) Eur[...]

TABLE OF CONTENTS ix SECTION 1 Characterist ics ................................................................. 1-1 1-1 Feat ures ................................................................................................................... .1 - 2 SECTION 2 Specifications and Performanc e ...................................... 2-1 2-1 An ten[...]

1-1 SECTION 1 Features 1-1 Featur es ............................................................................................................. 1-2[...]

1-1 Features 1-1 1-2 1-1 Features The V720–series Electromagnetic In ductive RFID System is ideal for the construction of highly functional , long–distance wireless ID sys tems for materi al control and logistics. The V720-HS04 Ant enna is used by connecting it to the V720S-BC5D4 A Reader/Writer usin g a coaxial cable with a spec ial impedance [...]

2-1 SECTION 2 Specifications and Performance 2-1 Ante nna.............................................................................................................. 2-2 2-1-1 Nomenclature ................................................................................................. 2-2 2-1-2 Specificat ions....................................[...]

2-1 Antenna 2-1 2-2 2-1 Antenna 2-1-1 Nomenclat ure • V720- HS04 No Name Description 1 BNC connector Connects the V720S-BC5D4A Reader/Writer to the Antenna connector for sending/receivi ng and to the exclus ive coaxial cable (sold separately). 2 Detection surface Surface for comm unication with Tag Antenna coils are arranged along the rectangular[...]

2-1 Antenn a 2-1 2-3 2-1-3 Dimensions • V720- HS04 Casing material PVC Back board PVC • Mou nt i n g h o l e Mou nt i n g h o l e Unit: mm[...]

2-1 Antenna 2-1 2-4 2-1-4 Cable (Sold separately)  General spe cifications Model Item V720-A41 Antenna cable Cable type Coaxial cable No. of leads 2 (shield) Insulation resistance 10M Ω or more between terminal an d coating (with DC250V Meg a) W i th stand voltage AC300V/1min Leak current: 1mA or less Coating material PVC  Outer dimensions [...]

3-1 SECTION 3 Installation 3-1 Installation of Ante nna...................................................................................... 3-2 3-1-1 Installation Environment ................................................................................ 3-2 3-1-2 Mounting th e Antenna ............................................................[...]

3-1 Installation of Antenna 3-1 3-2 3-1 Installation of Antenna 3-1-1 Install ation Envir onment Installation Location It is assumed that this pr oduct is t o be used indoors, or outd oors if th ere is a roof. Do not install the Ant enna in the followin g locations. • Place exposed to direct su nlight. • The ambient temperature is not wit hin a[...]

3-1 Installation of Antenna 3-1 3-3 3-1-2 Mounting the Ante nna Be sure to attach the provided brack et to the Antenna and mou n t the Antenna with four M6 screws with spring w ashers and flat washers as shown below. S pring washer Flat washer • Mounting Dimensional Drawin g ( H o l e ) ( H o l e ) Influence of peripheral metals during Antenna in[...]

4-1 SECTION 4 Reference Data 4-1 Communication s Areas ......................................................................................... 4-2 4-2 Influence of Peripheral Meta ls at Antenna In stallation ...................................... 4-5 4-3 Influence of T ag Angle .....................................................................[...]

4-1 Communications Areas 4-1 4-2 4-1 Communications Areas The following dia gram sh ows the communicat ion area availabl e when a standard Tag is used at ambient tempera ture, 25°C. Th e communication ar ea varies dependin g on Antenna insta llation conditions, Tag forming conditio ns, Tag installation conditions and ambient tem perature; therefor[...]

4-2 Influence of Periph eral Metals durin g Antenna Installat ion 4-2 4-3 4-2 Influence of Peripheral Metals of Antenna Installation Site Consider the influenc e of periphera l m eta ls when installing the Antenna. Peripheral m eta ls may greatly lower t he communicati on distance for the Ant enna. V720-HS04 to V720-D52P30/V720-D52 P 40 • Influen[...]

4-3 Influence of T ag Angle 4-3 4-4 4-3 Influence of Tag Angle The maximum comm unic ati ons range bet ween th e Ant enna and Tag wi ll b e ava il able i f th e face of the Antenn a and the fa ce of the Tag are parallel to each other. The commun ications range w ill be reduced if the Tag is mount ed at an ang le. T ake t he angl e of t he Tag int o[...]

4-4 Effects of Materials on T ags 4-4 4-5 4-4 Effects of Materials on Tags Take into consider ation the effects of th e mounting locat ion when mounting th e Tag. Communications range may be reduced if the Tag is near certain objects. The extent to which the distance will decrease depends on the actual ma terial and its shap e. Check the back of th[...]

4-4 Effects of Materials on T a gs 4-4 4-6 Test Setup • Metal Object • Resin Object Meta l Tag A nten na Commu nica tion dista nce Di stan ce be twee n ba ck m etal a nd Tag Re sin Tag Antenna Co mmu nica tio n di stan ce Material: Aluminum plate (th ickness = 2.0 mm) Dimensions: 240 x 190 mm[...]

Revision History A manual revision code appears as a suffix to the catalog number on the front cover of the manual. SRFM- 002A Revisi on code The following table outlines the changes made to the m anual during each revision. Page numbers refer to the previous version. Revis ion code Date Re vised conte nt 1 September, 2006 First Edition (New issued[...]

Manual No. SRFM-006A No t e: S pecif ications subject to change w ithout not ice. Prin ted in Jap an Authorized Distr ibutor: Up-to-date in formation on R FID Sy stems can be accessed at OM RON's web site at http://w ww .omro nrfid.com / OMRON CORPO RA TION RFID BUSINESS DEVELOPMENT DEP ARTMENT 14th Fl., Gat e City Osaki W est T ower 1-1 1-1 O[...]