NEC LCD2070NX manual

MultiSync LCD2070NX MultiSync LCD2070VX User ’ s Manual[...]

Index W arning, Caution ............................................................................................................... .......... English-1 Declaration ................................................................................................................................... English-1 Canadian Department of Communications C[...]

English English-1 W ARNING CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM W ALL SOCKET . T O FULL Y DISENGAGE THE POWER TO THE UNIT , PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET .DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE P ARTS INSIDE. REFER SER VICING T O QUALIFIED SERVICE PERSONNEL. [...]

English-2 Canadian Department of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1. FCC Information 1. Use the attached specif[...]

English English-3 Contents Y our new NEC MultiSync LCD monitor box* should contain the following: • MultiSync LCD monitor with tilt/swivel/height adjust stand • Power Cord • Cable cover •V ideo Signal Cable (15-pin mini D-SUB male to 15-pin mini D-SUB male) •V ideo Signal Cable (DVI-D to DVI-D) • USB Cable (LCD2070NX only) • User ’ [...]

English-4 Quick Start To attach the MultiSync LCD monitor to your system, follow these instructions: 1. T urn off the power to your computer . 2. For the PC or MAC with DVI digital output: Connect the DVI signal cable to the connector of the display card in your system ( Figure A.1 ). T ighten all screws. For the PC with Analog output: Connect the [...]

English English-5 Insert T op First 8. Make sure all cables are resting flat against the stand ( Figure C.3 ). 10. Connect the power cord to the power outlet ( Figure E.1 ). NOTE: If you have difficulty removing the cable cover , please push the lower opening upward to remove it, as show in Figure E.2 . NOTE: Please refer to Caution section of this[...]

English-6 Figure S.1 Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes: 1. Place hands on each side of the monitor and lift up to the highest position. Remove the cable cover ( Figure S.1 ). NOTE: If you have difficulty removing the cable cover , please push the lower opening upward to remove it, as shown in t[...]

English English-7 Figure S.3 Figure S.4 5. Lift up the stand to unlatch the upper hooks and remove the stand ( Figure S.3 ). 6. Remove the 2 screws on the top of the monitor ( Figure S.4 ). The monitor is now ready for mounting in an alternate manner . 7. Connect the cables to the back of the monitor . 8. Reverse this process to re-attach stand. NO[...]

English-8 Controls OSM (On-Screen Manager) control buttons on the front of the monitor function as follows: To access OSM menu, press any of the control buttons (MENU/EXIT , Left, Right, Down, Up). To change signal input, press the SELECT button. To change DV MODE, press the RESET/DV MODE button. NOTE: OSM must be closed in order to change signal i[...]

English English-9 Colour Control System Colour Control System: Six colour presets select the desired colour setting (sRGB and NA TIVE colour presets are standard and cannot be changed). R,G,B: Increases or decreases Red, Green or Blue colour depending upon which is selected. The change in colour will appear on screen and the direction (increase or [...]

English-10 Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MUL TISYNC LCD COLOUR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servi[...]

English English-11 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONIT OR CAN REDUCE EYE, SHOULDER AND NECK F A TIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Y our eyes should look slightly [...]

English-12 Specifications for MultiSync LCD2070VX Monitor Specifications MultiSync LCD2070VX Monitor Notes LCD Module Diagonal: 51 cm/20.1 inches Active matrix; thin film transistor (TFT) V iewable Image Size: 51 cm/20.1 inches liquid crystal display (LCD); 0.255 mm dot Native Resolution (Pixel Count): 1600 x 1200 pitch; 300 cd/m 2 * 3 white lumina[...]

English English-13 Specifications for MultiSync LCD2070NX Monitor Specifications MultiSync LCD2070NX Monitor Notes LCD Module Diagonal: 51 cm/20.1 inches Active matrix; thin film transistor (TFT) V iewable Image Size: 51 cm/20.1 inches liquid crystal display (LCD); 0.255 mm dot Native Resolution (Pixel Count): 1600 x 1200 pitch; 250 cd/m 2 white lu[...]

English-14 Features Thin-frame design creates more desktop space for you to work and play , while the flat screen’s crisp, bright images and crystal- clear text deliver a comfortable viewing experience. No T ouch Auto Adjust automatically adjusts your optimal image settings upon initial power-on. Colour Control System allows you to change between[...]

English English-15 T roubleshooting No picture • The signal cable should be completely connected to the display card/computer . • The display card should be completely seated in its slot. • Check the V acation Switch should be in the ON position. • Front Power Switch and computer power switch should be in the ON position. • Check to make [...]

English-16 TCO’03 Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also m[...]

English English-17 NEC DISPLA Y SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally- friendly products, and always strive to help define and comply with the latest independent s[...]