Makita N1900B manual

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com P o wer Planer 82 mm (3 - 1/4”) MODEL N1900B DOUBLE INSULA TION[...]

2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or s[...]

3 change the plug in any wa y . Double insula- tion eliminates the need for the three wire grounded pow er cord and grounded power supply system. 5. A void body contact with gr ounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 6. Do not expose power tools to [...]

4 model. Accessories that may be suitab le for one tool, may become hazardous when used on another tool. SER VICE 23. T ool ser vice mu st be performed only by qualified repair personnel. Service or main- tenance performed by unqualified personnel could result in a risk of injur y . 24. When servicing a tool, use only identical replacement parts. F[...]

5 poor installation or a poorly balanced blade . 8. Make sure the blade is not contacting the workpiece bef ore the switch is turned on. 9. W ait until the blade attains full speed before cutting. 10. Keep at least 200 mm (8”) awa y from the tool at all times. 11 . Alwa ys switch off and wait for the blades to come to a complete stop before an y [...]

6 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Adjusting depth of cut Depth of cut ma y be adjusted by simply turning the knob on the front of the tool. Switch action CA UTION: • Bef ore plugging in the tool, always chec k to see that the s wit[...]

7 • Handle the blades v er y carefully . Use glo ves or rags to protect your fingers or hands when remo ving or installing the blades. • Use only the Makita wrench provided to remo ve or install the blades . F ailure to do so may result in o ver tightening or insufficient tightening of the installation bolts. This could cause an injur y . 1. Re[...]

8 5. Slip the heel of the adjusting plate into the groov e of the drum. 6. Set the drum cover o ver the adjusting plate/set plate and screw in the three he x flange head bolts so that a gap e xists between the drum and the set plate to slide the mini planer blade into position. The b lade will be posi- tioned by the planer b lade locating lugs on t[...]

9 Place the blade on the gauge base so that the b lade edge is perf ectly flush with the inside edge of the gauge plate. Place the adjusting plate on the blade , then simply press in the heel of the adjusting plate flush with the back side of the gauge base and tighten two scre ws on the adjusting plate. Now slip the heel of the adjusting plate int[...]

10 Nozzle assembly (optional accessor y) Use of the special nozzle assembly will minimiz e chip scat- ter , making f or a cleaner wor k area. The nozzle assembly ma y be attached after the chip cov er on the tool body is remov ed. When slipping on the assembly , fit the pin on it into the rear cov er hole. Use the chip cov er screws to f asten it i[...]

11 OPERA TION Planing operation First, rest the tool front base flat upon the workpiece surface without the blades making an y contact. Switch on and wait until the blades attain full speed. Then mo ve the tool gently f orward. Apply pressure on the front of tool at the star t of planing, and at the back at the end of planing. Planing will be easie[...]

12 Y ou ma y wish to add to the length of the fence by attaching an e xtra piece of wood. Conv enient holes are provided in the f ence for this purpose, and also for attaching an e xtension guide (optional accessor y). Chamfering T o make a chamfering cut as show n in the figure, align the “ V ” groov e in the front base with the edge of the wo[...]

13 First, loosen the two wing nuts on the holder and insert the blades (A) and (B), so that the y contact the sides (C) and (D). Then tighten the wing nuts. Immerse the dressing stone in water f or 2 or 3 minutes bef ore shar pening. Hold the holder so that the blades both contact the dressing stone f or simultaneous shar pening at the same angle. [...]

14 Use a screwdriv er to remove the brush holder caps. T ake out the worn carbon br ushes , inser t the new ones and secure the brush holder caps. T o maintain product SAFETY and RELIABILITY , repairs, any other maintenance or adjustment should be perf or med by Makita A uthor iz ed or F actor y Ser vice Centers , always using Makita replacement pa[...]

Memo 15[...]

Memo 16[...]

17 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut[...]

18 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade[...]

19 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St. Fremont, CA 94538-5107 (510) 657-9881 14930 Northam St. La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Av enue Sacramento , CA 95825 (916) 482-5197 7674 Clair[...]

W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o[...]