Makita 5630DWA manual

Cordless Circular Saw Blade Cutting depth No load speed Overall 45" iRPMi length 2,600 diameter 90" 165 mm 0 54" 0- 38" 364 mm (6- 1 /2") 10 ~ 2-1/8") 10 ~ 1-1/2") (14-5116"J Equipped with Electric Brake MODEL 5630DWA MODEL 5680DWB With High Capacity Battery Charger With High Capacity Battery Charger Net weig[...]

GENERAL SAFETY RULES (For All Battery Operated Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. Do not o[...]

Tool Use and Care Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. *Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed[...]

Specific Safety Rules 1. DANGER! Keep hands away from cutting area and blade. Keep your second hand on auxiliary handle, or motor housing. If both hands are holding the saw, they cannot be cut by the blade. Keep your body positioned to either side of the saw blade, but not in line with the saw blade. KICKBACK could cause the saw to jump backwards. [...]

11. Causes and Operator Prevention of Kickback: Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the opera tor. When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back tow[...]

Do not use dull or damaged blade. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and KICKBACK. Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and KICKBACK. Use extra caution when making a &qu[...]

15. Place the wider portion of the saw base on that part of the workpiece which is solidly supported, not on the section that will fall off when the cut is made. As examples, Fig. 5 illustrates the RIGHT way to cut off the end of a board, and Fig. 6 the WRONG way. If the workpiece is short or small, clamp it down. DON'T TRY TO HOLD SHORT PLACE[...]

SYMBOLS The followings show the symbols used for tool. ...... volts ................................. amperes ................................. herts ................................. kilograms hours ................................. minutes ................................. seconds ................................. alternating current ............[...]

IMPORTANT SAFETY INSTRUCTIONS Length of Cord (Feet) AWG Size of Cord FOR CHARGER & 25 50 100 150 18 18 18 16 BATTERY CARTRIDGE 1. SAVE THESE INSTRUCTIONS - This manual 9[...]

ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (50OFI 2. Do not attempt to use a step-up transformer, an engine generator or DC power or ABOVE 4OoC (104OF). receptacle. 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals wi[...]

Installing or removing battery cartridge *Always switch off the tool before insertion or removal of the battery cartridge. *To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge. *To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing a[...]

*If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time, the charging light may flash in red color. If this occurs, wait for a while. Charging will begin after the battery cartridge cools. The battery cartridge will cool faster if you re[...]

Hex wrench storage When not in use, the conveniently stored. hex wrench can be CAUTIO N: Always be sure that the tool is switched off and the battery cartridge is removed before any adjustment is attempted. Adjusting depth of cut Loosen the lever on the depth guide and move the base up or down. At the desired depth of cut, secure the base by tighte[...]

CAUTION: After adjusting the depth of cut and bevel cutting angle, be sure to tighten the screw. Sighting The front of the base is notched to provide two guide edges. For straight cuts, align the edge with 0" engraved on it with your cutting line on the workpiece. For 45" bevel cuts, align the edge with 45" engraved on it with your c[...]

Operation Hold the tool firmly. Set the base plate on the workpiece to be cut without the blade making any contact. Then turn the tool on and wait until the blade attains full speed. Now simply move the tool forward over the workpiece surface, keeping it flat and advancing smoothly until the sawing is completed. To get clean cuts, keep your sawing [...]

MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes reg- ularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both ca[...]

Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. N i-Cd Tungsten carbide tipped saw blade Part No For wood To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b). Take the battery to yo[...]

Feb-04--'99 US CORDLESS CIRCULAR SAW Model 5630DW e- 59 Note: The switch and other part ConfigUratlOnS may differ from country to Country. 18[...]

MODEL 5630DW Feb-04-'99 US MACHINE ~ 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 21 28 29 30 I:"," GtD DESCRIPTION 16 21 31 41 51 61 71 81 91 1 1 2 2 2 1 1 1 1 3 2 1 1 1 1 1 1 1 1 1 1 DESCRIPTION 31 38 39 40 41 42 1 1 1 1 1 1 Tapping Screw 4x18 Switch Button Handle Cover Switch Lever Switch Battery Holder Stop Ring E-8 Lever 4[...]

I 1 MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy I Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, [...]