Makita 2030N manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27

Ir a la página of

Buen manual de instrucciones

Las leyes obligan al vendedor a entregarle al comprador, junto con el producto, el manual de instrucciones Makita 2030N. La falta del manual o facilitar información incorrecta al consumidor constituyen una base de reclamación por no estar de acuerdo el producto con el contrato. Según la ley, está permitido adjuntar un manual de otra forma que no sea en papel, lo cual últimamente es bastante común y los fabricantes nos facilitan un manual gráfico, su versión electrónica Makita 2030N o vídeos de instrucciones para usuarios. La condición es que tenga una forma legible y entendible.

¿Qué es un manual de instrucciones?

El nombre proviene de la palabra latina “instructio”, es decir, ordenar. Por lo tanto, en un manual Makita 2030N se puede encontrar la descripción de las etapas de actuación. El propósito de un manual es enseñar, facilitar el encendido o el uso de un dispositivo o la realización de acciones concretas. Un manual de instrucciones también es una fuente de información acerca de un objeto o un servicio, es una pista.

Desafortunadamente pocos usuarios destinan su tiempo a leer manuales Makita 2030N, sin embargo, un buen manual nos permite, no solo conocer una cantidad de funcionalidades adicionales del dispositivo comprado, sino también evitar la mayoría de fallos.

Entonces, ¿qué debe contener el manual de instrucciones perfecto?

Sobre todo, un manual de instrucciones Makita 2030N debe contener:
- información acerca de las especificaciones técnicas del dispositivo Makita 2030N
- nombre de fabricante y año de fabricación del dispositivo Makita 2030N
- condiciones de uso, configuración y mantenimiento del dispositivo Makita 2030N
- marcas de seguridad y certificados que confirmen su concordancia con determinadas normativas

¿Por qué no leemos los manuales de instrucciones?

Normalmente es por la falta de tiempo y seguridad acerca de las funcionalidades determinadas de los dispositivos comprados. Desafortunadamente la conexión y el encendido de Makita 2030N no es suficiente. El manual de instrucciones siempre contiene una serie de indicaciones acerca de determinadas funcionalidades, normas de seguridad, consejos de mantenimiento (incluso qué productos usar), fallos eventuales de Makita 2030N y maneras de solucionar los problemas que puedan ocurrir durante su uso. Al final, en un manual se pueden encontrar los detalles de servicio técnico Makita en caso de que las soluciones propuestas no hayan funcionado. Actualmente gozan de éxito manuales de instrucciones en forma de animaciones interesantes o vídeo manuales que llegan al usuario mucho mejor que en forma de un folleto. Este tipo de manual ayuda a que el usuario vea el vídeo entero sin saltarse las especificaciones y las descripciones técnicas complicadas de Makita 2030N, como se suele hacer teniendo una versión en papel.

¿Por qué vale la pena leer los manuales de instrucciones?

Sobre todo es en ellos donde encontraremos las respuestas acerca de la construcción, las posibilidades del dispositivo Makita 2030N, el uso de determinados accesorios y una serie de informaciones que permiten aprovechar completamente sus funciones y comodidades.

Tras una compra exitosa de un equipo o un dispositivo, vale la pena dedicar un momento para familiarizarse con cada parte del manual Makita 2030N. Actualmente se preparan y traducen con dedicación, para que no solo sean comprensibles para los usuarios, sino que también cumplan su función básica de información y ayuda.

Índice de manuales de instrucciones

  • Página 1

    Planer- Jointer Auto feed 320 mm (1242") MODEL 2030N With Electric Brake Width 0 mm - 150 mm 150 mm - 240 mm 240 mm - 320 mm High Low IO' - 5-7/87 l5-7/8" - 9.1/2"1 (9-112" - 12.1/2"1 speed speed Feed 320 mm .weed 112~1'2"' High speed 2 mm 15/64") 1.5mm11/16"l 1 mm15/128'1 8m 5m 1.5mm11/16[...]

  • Página 2

    BEFORE CONNECTING YOUR TOOL TO A POWER SOURCE Be sure you have read all GENERAL POWER TOOL SAFETY RULES GENERAL SAFETY PRECAUTIONS (For All Tools) 1. KNOW YOUR POWER TOOL. Read the owner's manual carefully. Learn the tools applications and limitations, as well as the specific potential hazards peculiar to it. 2. KEEP GUARDS IN PLACE and in wor[...]

  • Página 3

    16. 17. 18. 19. 20. 21. 22. 23. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position before plugging in. USE RECOMMENDED ACCESSORIES. Consult the owner's manual for recommended accessories. The use of improper accessories may cause risk of injury to persons. NEVER STAND ON TOOL. Serious injury could occur if the tool [...]

  • Página 4

    GROUNDING INSTRUCTIONS ALL GROUNDED, CORD-CONNECTED TOOLS: In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord hav- ing an equipment-grounding conductor and a grounding plug. The plug must be plugged into a ma[...]

  • Página 5

    ADDITIONAL SAFETY RULES 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. 13. 14. 15. 16. Don't use the tool in presence of flammable liquids or gases. Handle the blades very carefully. Check the blades carefully for cracks or damage before operation. Replace cracked or damaged blades immediately. Be sure the planer blade installation bolts are securely [...]

  • Página 6

    ADDITIONAL SAFETY RULES FOR JOINTER 1. Maintain the proper relationships of infeed and outfeed table surfaces and cut- terhead blade path. 2. Do not perform jointing operations on material shorter than 140 mm (5-112 inches), narrower than 19 mm (3/4 inch), or less than 12.7 mm (112 inch) thick. 3. Do not perform planing operations on material short[...]

  • Página 7

    HOW TO USE AUTO-PLANER 1. Adjusting depth of cut The maximum depth of cut changes in terms of the cutting speed and the width of the workpiece to be cut. See Fig. 1. Insert the workpiece flush with the in- feed table top so that the front end of the workpiece reaches at least 20 to 30 mm (3/4 to 1-1/8") beyond the depth gauge. Turn the crank h[...]

  • Página 8

    3. Switchover of cutting speed Turn the speed change lever to the right for high speed, and to the left for low speed. CAUTION. Change speeds while the tool is running, but do not attempt to do so during an actual planing operation. 4. Chip deflector The ejecting distance of chips can be adjusted by means of the chip deflector. To eject the chips i[...]

  • Página 9

    JOINTER 1. Cutting depth Set the depth of cut with the depth adjustment knob while watching the graduation on the scale plate. Fig. 6 2. Fence angle (0 - 45') Set the depth of cut to "0" graduation. Loosen the thumb screws holding the fence in place. Pull out the fence by at least 25 mm (1") and tighten the thumb screws. Loosen [...]

  • Página 10

    OPE RATION 1. Auto-Planer Determine the depth of cut and the cutting speed in terms of the width of the work- piece you intend to cut. Insert the workpiece flush with the table top. When cutting the long and heavy workpiece, lift up the end of the workpiece slightly at the start and the end of cutting to avoid gouging or sniping at the extreme ends[...]

  • Página 11

    Jointing edge Set the fence square with the table. Hold the best face of the workpiece firmly against the fence throughout the feed. (Fig. 10) CAUTION : Cover the cutterhead with the safety cover when the fence is pulled out. (Fig. 11). However, never touch the safety cover when the jointer is running. Jointing warped workpieces If the workpiece is[...]

  • Página 12

    Direction of grain Avoid feeding workpiece into the Jointer against the grain as shown in Fig.13. The result will be chipped and splintered edges. Feed with the grain as shown in Fig. 14, to obtain a smooth surface. Wor kpiece Outfeed table lnfeed table Cutterhead Wrong feed -against the grain. Fig. 1: I- V- Correct feed - with the grain Fig. 14 12[...]

  • Página 13

    CHANGING PLANER BLADES 1. a Removing blades 1 Remove the screw of the chip cover. cover. on the outfeed side Then open the chip Fig. 1 Loosen the hex bolt with the wrench and lift off the safety guard assembly. Set the depth of cut for Jointer to maximum graduation. *Push the lock plate in the direction of the arrow and raise it slightly. Turn the [...]

  • Página 14

    0 Lock the drum at the position shown in Fig. 17 and loosen the hex bolts with the When removina the blade from the Auto-Planer, lock the drum at the position shown socket wrench. Remove the hex bolts and the drum cover. 0 Insert the blade between the drum and the blade holder. Set the blade so that it will protrude by 2 mm (5/64") to 3 mm (1/[...]

  • Página 15

    .On the Auto-Planer, press down on both ends of the blades with wooden levelers. *On the Jointer, set the leveler on the outfeed table and slide it out over the blade edge. The edge of blade should just contact underside of leveler. Lock the drum at the position shown in Fig. 17. Mount the drum cover and tighten the hex bolts evenly and alternately[...]

  • Página 16

    VARIOUS ADJUSTMENTS 1. Adjusting infeed/outfeed rollers (Auto-planer) NOTE : The planer infeed and outfeed rollers are factory adjusted. If you notice the adjust- ment is off, kindly do as follows. Use the wrench to loosen the installation nuts slightly. Turn the adjusting screw to obtain a level of from 0.1 to 0.3 mm above the table surface. It is[...]

  • Página 17

    MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection and maintenance. Replacing carbon brushes .Remove and check the carbon brushes regularly. Replace when they wear down to about 6 mm (1/4") or less. Keep the brushes clean and free to slip in the holders. Both brushes should [...]

  • Página 18

    .Take out the worn brush, insert the new one and secure the brush holder cap. Fig. 31 Cleaning Always brush off dirt, chips and foreign matter adhering to roller surfaces, motor vents. Make sure that water or oil does not enter the motor. Lubrication (periodic) Oil the chain (after removing the chain cover), the column moving parts (contact areas) [...]

  • Página 19

    Sharpening planer blades (In case of blade width 155 mm (6-1/8”)) 1. Remove the two wing nuts on the holder. 2. Set the blade A and blade B on the holder so that the heel of the blade will be flush against C and D surface of the holder respectively. 3. Tighten the wing nuts to hold the blades in the holder. 4. Sharpen with the dressing stone keep[...]

  • Página 20

    ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Sharpening Holder (Part No. 123006-2) 0 Tria[...]

  • Página 21

    Dressing Stone 180-1200 (Part No. 741801-4) Key (Part No. 411447-7) Leveler (Part No. 41 1908-71 Wrench (Part No. 781202-4) 21[...]

  • Página 22

    Seo -19-'84 US 320 mm (12-1/2") Model 2030N PLANER-JOINTER 22[...]

  • Página 23

    23[...]

  • Página 24

    Note: The switch and other part configurations may differ from country to country. 24[...]

  • Página 25

    MODEL 2030N AiD DESCRIPTION Sep 19-84 US AtD DESCRIPTION MACHINE ~ 1 2 3 4 5 6 7 8 9 10 I1 16 17 IS 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 3 1 I 2 2 2 3 2 2 2 1 1 2 1 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 2 2 2 1 6[...]

  • Página 26

    MODEL 2030N Sep.-19-84 US 'itM $tD DESCRIPTION ';,'d" $ZD DESCRIPTION MACHINE ~ 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 166 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 180 109 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 21[...]

  • Página 27

    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -. . -. . . . . . . . MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from t[...]