Jacuzzi S198 manual

Affinity ™ Owner's Manual[...]

Note: This is a professional grade product. A knowledge of construction techniques, plumbing and electrical installation according to codes are required for proper installation and user satis- faction. We recommend that a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath products. Our warranty does not cover improper instal[...]

Contents Specifications & Rough-in Reference _____________________________________________________ 2 Framing and Support _________________________________________________________________ 3 Wall Cutout & CD/Radio Installation ______________________________________________________ 4-5 TV Installation __________________________________________[...]

Specifications & Rough-in Reference DIMENSIONS 68" (1727 mm) L 68" (1727 mm) W 22" ( 559 mm) H1 27" ( 686 mm) H2 35-7/8" ( 911 mm) H3 DRAIN/OVERFLOW DIMENSIONS 19" (483 mm) A 12" (305 mm) B TOTAL WEIGHT/FLOOR LOADING 1500 lb (682 kg)/ 47 lb/sq. ft. (229 kg/sq. m) OPERATING GALLONAGE 120 U.S. gal (455 liters) P[...]

Framing and Support The drain/overflow of the bath extends below the bottom of the bath. Note that this requires a cutout in the floor . The floor structure beneath the bath must be able to support a total weight of bath, water , and bather . Refer to the table under total weight for your model. The unit must be supported from the bottom of the bat[...]

W all Cutout and CD/Radio Installation The installation requires a cutout in the wall. The cutout allows room for the speakers, CD/Radio speaker/power & TV audio cable wires. NOTE: CD/Radio must be must be located a minimum of 5' away from the interior of the bath. The cable provided with the unit is designed for this minimum distance. If [...]

Remove trim plate. Remove sleeve after disengaging sleeve locks. Stand the unit and insert the 2 handles between the unit and sleeve to disengage the sleeve locks. When standing the unit be careful not to damage the fuse on the rear. Remove the sleeve. Retain the handles for future use. Run wires through sleeve. Insert sleeve into build out. When f[...]

TV Installation Remove back cover by lifting straight upward and then remove the drip shield. Tighten cable tie and cut off excess. Tighten cable tie with anchor (not supplied) to the TV power cord. It is not necessary to attach anchor to drip shield; the cable tie and anchor are used to ensure the TV power cord remains in the TV housing. Locate bl[...]

Service Access For partially or fully sunken installations, allow for ac- cess to service connections. It is the installer's respon- sibility to provide sufficient service access. See Ser- vice Access illustration. Provide adequate ventilation (minimum 30 square inch opening) for cooling the mo- tor and to supply sufficient air for the jets. E[...]

Drain Information A drain/overflow assembly must be installed on the bath, water tested, and connected to the sanitary system of the house. After opening the carton, inspect for dam- age and verify that the kit is of the proper finish. In the Jacuzzi Whirlpool Bath drain/overflow kit, note that the waste flange, strainer , overflow cover and cover [...]

9 Remote Control LED INDICA TOR BA TH MODE CHANNEL UP & DOWN JETS FUNCTION LIGHT FUNCTION TV MODE VOLUME UP & DOWN CD/DVD FUNCTION BLOWER FUNCTION POWER The Floating Remote Control is a universal remote control that has been programmed to operate the TV . If the remote has been deprogrammed the following procedure will reprogram the remote:[...]

PURGES Automatic Purge With all functions off either , manually or by program, a 60 minute timer will be initiated. Once this timer is fin- ished, a 1 minute purge will be activated (blower) to purge any remaining water in the air channel. If any key is pressed the purge timer will be reset. Daily Purge If the user holds the button on the bath cont[...]

Controlling Whirlpool Action The whirlpool action in your bath is influenced by three factors – direction of flow , force of water , and force of air . Direction: To change the direction of the water flow , swivel the jet nozzle to the desired angle. The jets can be directed individually toward any location on your body to provide a hydromassage.[...]

BA TH MAINTENANCE Cleaning the Bath To clean your bath, simply use a mild, nonabrasive liq- uid detergent solution. Y ou can protect and restore the gloss to a dulled acrylic surface by applying Meguiar's #10 Mirror Glaze, a product specifically designed for use on acrylic finishes. If Meguiar's is not available, an acrylic polish of equa[...]

Lamp When the bulb burns out, replace it from the back of the lamp fitting, on the underside of the shell, by pulling out the bulb receptacle. Replacement bulbs (7W , 12V) are available from your Jacuzzi Whirlpool Bath dealer . LIGHT BULB LIGHT BEZEL SHELL BULB RECEPT ACLE LOCKING NUT LIGHT BULB REPLACEMENT Printed in the U.S.A. Printed on Recycled[...]

14[...]

53 mm 182 mm TEMPLA TE FOR CD/RADIO MOUNTING SLEEVE 15[...]

[...]

WARRANTY COVERAGE Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Designer Collection Bath Product (“unit”) who purchases the product for personal or single family use (“user”). The Company will repair or replace, at its option, the unit or its [...]

RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility. In [...]