Electrolux EHG 678W manual

2 Models EHG 678 B - EHG 678 W 35670-2701 GB Gas Hob INSTR UCTION BOOKLET[...]

3 Important Safety Infor mation You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 01635 522799 Installation ● This hob must be installed by qualified personnel, according to the manufacturer ’ s instructions and to the relevant British Standards. ● Any ga[...]

4 F or the User Description of the Hob Page 5 Operation Page 6 Maintenance and Cleaning Page 7 Something Not W orking? Page 8 Service and Spare Parts Page 8 Guarantee Conditions Page 9 Electrolux Service For ce Centre Addresses Page 10 This appliance is manufactured according to the following EEC directives: 73/23 EEC - 90/683 EEC - 93/68 EEC - 89/[...]

5 1. Hob T op 2. Rapid Burner 3. Semi-rapid Burners 4. Auxiliary Burner 5. Control Panel 6. Control knob for back left burner (semi-rapid) 7. Control knob for front left burner (rapid) 8. Control knob for front right burner (auxiliary) 9. Control knob for back right burner (semi-rapid) Description of the Hob INSTALLATION Any gas installation must b[...]

6 HOB BURNERS T o light a burner , turn the relevant knob anticlockwise to maximum position and push down the knob to ignite. If the burner does not ignite, turn the control knob to zero, and try again. When switching on the mains, after installation or a power cut, it is quite normal for the spark generator to be activated automatically . T o ensu[...]

7 Befor e any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply . The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob T op Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little wasing [...]

8 Something Not W orking? If the hob is not working correctly , please carry out the following checks before contacting your local Electrolux Service Force Centre. SYMPTOM ■ There is no spark when lighting the gas ■ The gas ring burns unevenly SOLUTION ◆ Check that the unit is plugged in and the electrical supply is switched on ◆ Check that[...]

9 Guarantee Conditions ELECTROLUX STANDARD GUARANTEE CONDITIONS W e, Electrolux, undertake that if, within 12 months of the date of the purchase, this Electrolux appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for lab[...]

10 CHANNEL ISLANDS GUERNSEY Guernsey Electricity PO Box 4 V ale , Guernsey Channel Islands JERSEY Jersey Electricity Company PO Box 45 Queens Road St Helier Jersey Channel Islands JE4 8NY SCOTLAND ABERDEEN 8 Cornhill Arcade (M05) Cornhill Drive Aberdeen AB2 5UT AUCHTERMUCHY 33A Burnside (M03) Auchtermuchy Fife KY14 7AJ BLANTYRE Unit 5 (M07) Block 2[...]

11 MIDLANDS BIRMINGHAM 66 Birch Road East, (M18) W yrley Road Industrial Estate Witton Birmingham B67DB BOURNE Manning Road Ind (M44) Estate Pinfold Road Bourne PE10 9HT BRIDGNOR TH 1 Underhill Street (M72) Bridgnorth Salop WV16 4BB GLOUCESTER 101 R ycroft Street (M23) Gloucester GL1 4NB HEREFORD Unit 3 (M31) Bank Buildings Cattle Market Hereford H[...]

12 Ignition HT Spark Spark Generator Ispra Control's BF 50046 - 230-240V 0.6 Y A T 120 Spark Gap Fixed OVERALL DIMENSIONS W idth: 580 mm. Depth: 500 mm. Height: 88 mm. W eight: 8,5 Kg. Burner Dia. Tap By-pass Tap colour 1/100 mm Auxiliary 28 Red/Red Semi-rapid 32 Blue/Blue Rapid 40 Black/Black Aeration adjustment none Instructions for the Inst[...]

13 Important safety requir ements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE W iring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Par . 2 and B.S. 6891 Current Editio[...]

14 FO 2065 Rectangular cut-out size for hob A) End of shaft with nut B) W asher C) Elbow It is impor tant to install the elbow correctly , with the shoulder on the end of the thr ead, fitted to the hob connecting pipe. Failur e to ensur e the corr ect assembly will cause leakage of gas. FO 0814 Gas Connection Connection to the gas supply should be [...]

15 Building In ON/OFF SWITCH FLEX OUTLET ON/OFF SWITCH FLEX OUTLET FO 0763 FO 0764 30 20 min 60 a b FO 1013 1 2 3 Dimensions are given in mm. Building o v er a cupboar d or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface[...]

16 Electrical connections Any electrical work r equired to install this hob should be carried out by a qualified electrician or competent person, in accor dance with the curr ent r egulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230[...]

17 W iring diagram 1. TAPS IGNITOR SWITCHES 2. IGNITOR UNIT 1 2 L N 0 220 240 1 2 3 4[...]

18 Fault Finding Pr eliminar y Electrical Systems Check A. EARTH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary . a) T est leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (Ohm), check all earth wires for continuity and [...]

19 Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check fitting of burners Check position of the electrode Check by pass simmer adjusted Light burner manually Check gas supply at burner Check continuity fro[...]

20 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. T o do this, follow the procedure below . - T urn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguishe[...]

21 Servicing Conversion fr om Natural Gas to LPG It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted. The gas rate is adjusted to suit. Method • Ensure that the gas taps are in the 'OFF' position • Isolate the ho[...]