Bunn TS manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25

Ir a la página of

Buen manual de instrucciones

Las leyes obligan al vendedor a entregarle al comprador, junto con el producto, el manual de instrucciones Bunn TS. La falta del manual o facilitar información incorrecta al consumidor constituyen una base de reclamación por no estar de acuerdo el producto con el contrato. Según la ley, está permitido adjuntar un manual de otra forma que no sea en papel, lo cual últimamente es bastante común y los fabricantes nos facilitan un manual gráfico, su versión electrónica Bunn TS o vídeos de instrucciones para usuarios. La condición es que tenga una forma legible y entendible.

¿Qué es un manual de instrucciones?

El nombre proviene de la palabra latina “instructio”, es decir, ordenar. Por lo tanto, en un manual Bunn TS se puede encontrar la descripción de las etapas de actuación. El propósito de un manual es enseñar, facilitar el encendido o el uso de un dispositivo o la realización de acciones concretas. Un manual de instrucciones también es una fuente de información acerca de un objeto o un servicio, es una pista.

Desafortunadamente pocos usuarios destinan su tiempo a leer manuales Bunn TS, sin embargo, un buen manual nos permite, no solo conocer una cantidad de funcionalidades adicionales del dispositivo comprado, sino también evitar la mayoría de fallos.

Entonces, ¿qué debe contener el manual de instrucciones perfecto?

Sobre todo, un manual de instrucciones Bunn TS debe contener:
- información acerca de las especificaciones técnicas del dispositivo Bunn TS
- nombre de fabricante y año de fabricación del dispositivo Bunn TS
- condiciones de uso, configuración y mantenimiento del dispositivo Bunn TS
- marcas de seguridad y certificados que confirmen su concordancia con determinadas normativas

¿Por qué no leemos los manuales de instrucciones?

Normalmente es por la falta de tiempo y seguridad acerca de las funcionalidades determinadas de los dispositivos comprados. Desafortunadamente la conexión y el encendido de Bunn TS no es suficiente. El manual de instrucciones siempre contiene una serie de indicaciones acerca de determinadas funcionalidades, normas de seguridad, consejos de mantenimiento (incluso qué productos usar), fallos eventuales de Bunn TS y maneras de solucionar los problemas que puedan ocurrir durante su uso. Al final, en un manual se pueden encontrar los detalles de servicio técnico Bunn en caso de que las soluciones propuestas no hayan funcionado. Actualmente gozan de éxito manuales de instrucciones en forma de animaciones interesantes o vídeo manuales que llegan al usuario mucho mejor que en forma de un folleto. Este tipo de manual ayuda a que el usuario vea el vídeo entero sin saltarse las especificaciones y las descripciones técnicas complicadas de Bunn TS, como se suele hacer teniendo una versión en papel.

¿Por qué vale la pena leer los manuales de instrucciones?

Sobre todo es en ellos donde encontraremos las respuestas acerca de la construcción, las posibilidades del dispositivo Bunn TS, el uso de determinados accesorios y una serie de informaciones que permiten aprovechar completamente sus funciones y comodidades.

Tras una compra exitosa de un equipo o un dispositivo, vale la pena dedicar un momento para familiarizarse con cada parte del manual Bunn TS. Actualmente se preparan y traducen con dedicación, para que no solo sean comprensibles para los usuarios, sino que también cumplan su función básica de información y ayuda.

Índice de manuales de instrucciones

  • Página 1

    OPERA TING & SER VICE MANU AL B UNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 10690.0001C 6/00 ©1998 Bunn-O-Matic Corporation CW A-APS,TS CWT A-APS,TS[...]

  • Página 2

    Page 2 INTRODUCTION This equipment will brew a half-gallon batch of coffee into an awaiting dispenser. It can be easily configured for either pour-over or automatic brewing. The automatic version may include a hot water faucet for allied beverage use. It is only for indoor use on a sturdy counter or shelf. W ARRANTY Bunn-O-Matic Corp. (“Bunn”) [...]

  • Página 3

    Page 3 USER NOTICES Carefully read and follow all notices in this manual and on the equipment. All labels on the equipment should be kept in good condition. Replace any unreadable or damaged labels. # 00656.0000[...]

  • Página 4

    Page 4 ELECTRICAL REQUIREMENTS CAUTION - The brewer must be disconnected from the power source until specified in Initial Set-Up. "A" Models require 2-wire grounded service rated 230-240 volts ac, 20 amp, single phase, 50 Hz. Electrical Hook-Up CAUTION – Improper electrical installation will damage electronic components. 1. An electrici[...]

  • Página 5

    Page 5 Models CWTFA-APS & CWTFA-TS 1. Attach the flare fitting from the short piece of tubing on the flow control (supplied) to the lower water inlet fitting at the left rear of the brewer. 2. Attach the flare fitting from the short piece of tubing on the tee (supplied) to the upper water inlet fitting at the left rear side of the brewer. 3. Fl[...]

  • Página 6

    Page 6 10690.1 063000 7. Place the "ON/OFF" switch in the “ OFF ” (lower) position after water has stopped flowing from the funnel, and let the water in the tank reheat to the proper temperature. 8. Empty the dispenser and proceed as directed: 8A. Models CWA-PS & CWA-TS: The brewer is now ready for use in accordance with the coffe[...]

  • Página 7

    Page 7 OPERA TING CONTROLS Models CWA-APS & CWA-TS: These models function without operating controls. Models CWTA-APS, CWTFA-APS, CWTA-TS & CWTFA-TS: ON/OFF SWITCH Placing the "ON/OFF" switch in the "OFF" (lower) position stops brewing. Stopping a brew cycle after it has been started will not stop the flow of water into [...]

  • Página 8

    Page 8 TROUBLESHOOTING A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic Technical Service Department. • Inspection, testing, and repair of electrical equipment should be performed only by[...]

  • Página 9

    Page 9 TROUBLESHOOTING (cont.) Brew cycle will not start (cont.) Water is not hot Inconsistent beverage level in dis- penser PROBABLE CAUSE REMEDY 7. Water strainer/flow control (.222 GPM)(CWTA-APS, CWTFA- APS, CWTA-TS, CWTFA-TS) 1. Tank Heater Switch 2. Limit Thermostat CAUTION - Do not eliminate or bypass limit thermostat. Use only B.O.M. replace[...]

  • Página 10

    Page 10 TROUBLESHOOTING (cont.) Inconsistent beverage level in the dispenser (cont.) Consistently low beverage level in the dispenser Spitting or excessive steaming Dripping from sprayhead 4. Water Pressure (CWTA-APS, CWTFA-APS,CWTA-TS & CWTFA- TS) 1. Timer (CWTA-APS, CWTFA- APS, CWTA-TS & CWTFA-TS) 2. Strainer/flow Control (.222 GPM) 1. Li[...]

  • Página 11

    Page 11 TROUBLESHOOTING (cont.) Water flows into tank continuously (ON/OFF Switch "ON") Water flows into tank continuously (ON/OFF Switch "OFF") Beverage overflows dispenser Weak beverage 1. Timer (CWTA-APS, CWTFA- APS, CWTA-TS & CWTFA-TS) 1. Solenoid Valve (CWTA-APS, CWTFA-APS, CWTA-TS & CWTFA- TS) 1. Dispenser 2. Timer[...]

  • Página 12

    Page 12 TROUBLESHOOTING (cont.) Weak beverage (cont.) Dry coffee grounds remain in the funnel Brewer is making unusal noises Brewer is making unusal noises (CW) 5. Water Temperature 1. Funnel Loading 1. Solenoid (CWTA-APS, CWTFA- APS, CWTA-TS & CWTFA-TS) 2. Plumbing Lines 3. Water Supply 4. Tank Heater 1. Tank Heater Place an empty funnel on an[...]

  • Página 13

    Page 13[...]

  • Página 14

    Page 14 SERVICE (cont.) CONTROL THERMOSTAT Location: The control thermostat is located inside the trunk on the upper left side of the component bracket. Test Procedures: 1. Disconnect the brewer from the power source. 2. Locate the blue wire on the control thermostat. 3. With a voltmeter, check the voltage across the blue wire on the control thermo[...]

  • Página 15

    Page 15 SERVICE (cont.) LIMIT THERMOSTAT (CWTA & CWTFA) Location: The limit thermostat is located inside the rear of the hood on the tank lid. Test Procedures: 1. Disconnect the brewer from the power source. 2. Disconnect the blue and black wires from the limit thermostat. 3. With an ohmmeter, check for continuity across the limit thermostat te[...]

  • Página 16

    Page 16[...]

  • Página 17

    Page 17 SERVICE (cont.) SOLENOID VALVE Location: The solenoid valve is located inside the trunk on the lower center part of the component bracket. Test Procedures: 1. Disconnect the brewer from the power source. 2. Disconnect the white/green wire and black wire from the solenoid valve. With the "ON/OFF" switch in the "ON" (upper[...]

  • Página 18

    Page 18 SERVICE (cont.) START SWITCH P1467.40 Location: The start switch is located in the front of the hood just to the right of center. Test Procedure: 1. Disconnect the brewer from the power supply. 2. Disconnect the white/orange wire from the top switch terminal and the white/yellow wire from the bottom switch terminal. 3. Check for continuity [...]

  • Página 19

    Page 19[...]

  • Página 20

    Page 20 SERVICE (cont.) TANK HEATER SWITCH P2195.40 Location: The tank heater switch is located on the rear of the brewer on the upper left side of the trunk. Test Procedure: 1. Disconnect the brewer from the power source. 2. Disconnect the black wire from the limit thermo- stat (Automatics only) or the blue wire (Pour Overs only). 3. With the tank[...]

  • Página 21

    Page 21 13. Insert new tank heater switch through the hole in the upper left rear of the trunk and secure with switch indicator/guard bracket, hex facenut and plastic facenut. 14. Refer to Fig. 15 and reconnect the wires to the tank heater switch terminals. 15. Set tank assembly inside the hood on mounting brackets and secure with two #8-32 screws.[...]

  • Página 22

    Page 22 FIG. 17 TIMER TERMINALS P1472 TL1 WHI/RED from ON/OFF Switch(1) TL2 RED to Terminal Block (Red Insert) TL3 WHI/ORN from Start Switch TL4 WHI/GRN from Solenoid TL5 WHI/YEL from Start Switch TIMER (Early Models) FIG. 16 TIMER P1468.40 Location: The timer is located inside the front of the trunk on the component bracket. It consists of the dia[...]

  • Página 23

    Page 23 SERVICE (cont.) DIGITAL BREW TIMER (Late Models) P2195.40 FIG. 18 DIGITAL BREW TIMER Location: The timer is located inside the front of the trunk on the top of the component bracket. Test Procedure. NOTE: Do not remove or install wires while timer board is installed. Pressure applied to one side may cause damage to the board. 1. Disconnect [...]

  • Página 24

    Page 24 TL1 WHI/RED from ON/OFF Switch(1) TL2 RED to T erminal Block (Red Insert) TL3 WHI/ORN from Start Switch TL4 WHI/GRN from Solenoid TL5 WHI/YEL from Start Switch FIG. 19 DIGIT AL TIMER WIRING P2037 SERVICE (cont.) DIGITAL BREW TIMER (Late Models)(cont.) T imer Setting: NOTE: Prior to setting or modifying volumes, check that the brewer is conn[...]

  • Página 25

    Page 25[...]