Zanussi ZGL 62 ITX Bedienungsanleitung

GAS HOB ZGL 62 ITX INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance GB IE[...]

2 Import ant Safety Information Y ou MUST read these warnings carefully before inst alling or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Inst allation z This appliance must be installed and serviced by a competent person as stated in the Gas Safety ( Installation and Use) Regulations Current Editions[...]

3 Keep this instruction book for future reference and ensure it is passed on to any new owner . For the User Content s For the Inst aller Important Safety Information 2 Description of the Hob 4 Operation 5 Maintenance and Cleaning 6 Something Not Working? 7 Service and S pare Parts 7 Guarantee/Customer Service 16 European guarantee 17 Instructions [...]

4 Description of the Hob 1. Hob T op 2. Auxiliary Burner 3. Semi-rapid Burners 4. Rapid Burner 5. Control knobs 6. Electric Ignition Push Button 1 3 2 3 4 5 6[...]

5 Operation A - Burner cap B - Burner crown C - Ignition electrode D - Thermocouple Burner minimum maximum diameter diameter Large (rapid) 180 mm 260 mm Medium (semi-rapid) 120 mm 220 mm Small (auxiliary) 80 mm 160 mm Hob burners T o light a burner: z push the electric ignition pushbutton which is marked by a little spark. z at the same time turn t[...]

6 Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply . The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob T o p Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing[...]

7 Something Not W orking? If the hob is not working correctly , please carry out the following checks before contacting your local Zanussi Service Force Centre. IMPORT ANT : If you call out an engineer to a fault listed below , or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarant[...]

8 Rear Left Burner (semi rapid) Heat Input 2.0 kW (6824 BTU/HR) Front Lef t Burner (auxiliary) Heat Input 1.0 kW (3412 BTU/HR) Rear Right Burner (semi rapid) Heat Input 2.0 kW (6824 BTU/HR) Front Right Burner (rapid) Heat Input 3.0 kW (10236 BTU/HR) Instructions for the Inst aller Engineers technical dat a Overall dimensions Width: 580 mm Depth: 50[...]

9 Import ant safety requirement s 650 mm 400 mm 400 mm 100 mm 50 mm 50 mm 55 mm 600 mm 700 mm 400 mm 100 mm 400 mm 50 mm 55 mm 50 mm I CLEARANCES REQUIRED WHEN FITTING THE HOB WITHOUT A COOKER HOOD ABOVE CLEARANCES REQUIRED WHEN FITTING THE HOB WITH A COOKER HOOD ABOVE FO 0813 FO 0812 700 mm This hob must be installed in accordance with the Gas Saf[...]

10 Rectangular cut-out size for hob A) End of shaft with nut B) W asher C) Elbow FO 0814 Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper . The connection should be suit able for connecting to RC 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a[...]

11 FO 0763 FO 0764 FO 1013 2 3 FO 0199 a Fitting the Hob into the worktop ) Carry out the building in of the hob as follows: • put the seals supplied with the hob, on the edges of the cut out taking care that the seals meet without overlapping; • place the hob in the cut out, taking care that it is centred; • fix the hob with the relevant fix[...]

12 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230 V 5[...]

13 Fault Finding Preliminary Electrical Systems Check A. EARTH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary . a ) T est leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (Ohm), check all earth wires for continuity and all[...]

14 Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check fitting of burners Check position of the electrode Check by pass simmer Light burner manually Check gas supply at burner Check continuity from 'N[...]

15 Conversion from Natural Gas to LPG IMPORTANT The replacement/conversion of the gas hob should only be undertaken by a competent person. It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted and the gas rate is adjusted to sui[...]

16 Guarantee/Customer Service Standard guarantee conditions We, Zanussi-Electrolux, undertake that if within 12 months of the date of the purchase this Zanussi-Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option rep air or replace the same FREE OF CHARGE for la[...]

17 This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the countries listed below the appliance guarantee will move with you subject to the following qualifications: ?[...]

18[...]

19[...]

Grafiche MDM - Forlì 35687-8002 1 1/06 www .zanussi-electrolux.co.uk[...]