Telex Firefly P250 Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37

Zur Seite of

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Telex Firefly P250 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Telex Firefly P250, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Telex Firefly P250 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Telex Firefly P250. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Telex Firefly P250 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Telex Firefly P250
- Den Namen des Produzenten und das Produktionsjahr des Geräts Telex Firefly P250
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Telex Firefly P250
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Telex Firefly P250 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Telex Firefly P250 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Telex finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Telex Firefly P250 zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Telex Firefly P250, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Telex Firefly P250 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    T elex ® User’s Manual Firefly ™ P200/P250 LCD Notebook Projector COMPUTER MONITOR AUDIO OUT AUDIO IN SVHS VIDEO Firefly P200[...]

  • Seite 2

    The lightning flash with arrowhead symbol is displayed on the product to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may constitute a risk of electric shock. The exclamation point symbol is displayed on the product to alert the user to the presence of important operating and maintenanc[...]

  • Seite 3

    8. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at wall outlets, convenience receptacles, and the point where they exit from the product. 9. Lightning - For added protection for this product during a light[...]

  • Seite 4

    Warranty Telex warrants that the Firefly ™ P200/P250 will provide a usable active pixel ratio of at least 99.995%. This means that out of 1.44 million pixels on the Firefly ™ P250 (921,600 pixels on the P200), less than 50 pixels will be inactive. Inactive pixels may appear illumi nated on the display, however, they will not affect picture qual[...]

  • Seite 5

    TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIO NS ................. i i Warranty .............................. i v FCC Statement ........................... i v Canadian Department of Communications Statement ....... i v GENERAL FEA TURES ......................... 1 ACCESSORIE S ............................ 3 UNPACKING THE P200/P250 ...............[...]

  • Seite 6

    GENERAL FEATURES The Firefly ™ P200/P250 is a full-color compact LCD projection system that is used to display a computerized multi-media presen tation. The built-in amplifier/speakers lets you connect to a wireless microphone, portable CD player, or to the auxiliary output of a stereo system. The P200/P250 also allows you to connect to the outpu[...]

  • Seite 7

    The Firefly ™ P200/P250 can be connected to any IBM or IBM compatible computer equipped with a VGA/SVGA video output. The P200/P250 can also be connected to any Apple Macintosh computer that is equipped with a standard Macintosh video output. The Firefly ™ P200/P250 uses advanced thin-film-transi stor liquid crystal display (TFT LCD) technology[...]

  • Seite 8

    ACCESSORIES The accessories shown in Figures 2 and 3 are available for use with the Firefly ™ P200/P250 LCD notebook projector: The RC-8 is specifically designed for use with the Firefly ™ P200/P250. It allows remote control of all the P200/P250 keypanel and on-screen functions. (The RC-8 comes with the Firefly ™ P200/P250.) The B-10 features[...]

  • Seite 9

    UNPACKING THE P200/P250 Unpack the Firefly ™ P200/P250 LCD notebook projector and check the package contents. Refer to Figure 4 and the following list for items that are included in the P200/P250: • P200/P250 LCD notebook projector, with appropriate labels • User’s manual • Quick reference guide • Adapter Redemption Card • VGA/SVGA vi[...]

  • Seite 10

    ADAPTERS (Used on Macintosh units only) VGA/SVGA VIDEO CABLE POWER CORD COMPOSITE VIDEO (RCA to RCA) RC-8 REMO TE SOFTCASE AUDIO CABLE (dual RCA to 1/8" stereo) AUDIO CABLE (1/8" stereo to 1/8" stereo) SOURCE POWER BRIGHT CONTRAST VOLUME F1 MENU/RESET W arranty Card Registration Card Firefly P200 Quick Reference Guide U Manual Firefl[...]

  • Seite 11

    P200/P250 SETUP This section is a detailed description of the setup for your P200/P250. Positioning the Firefly ™ P200/P250 On the Desktop 1. Place the P200/P250 on a table or desktop as shown in Figure 5. NOTE: Ensure that the P200/P250 vents are not blocked. The P200/P250 takes in cool air at the side of the projector. Hot air is exhausted at t[...]

  • Seite 12

    2. Press and release the locking mechanism, then lift the P200/P250 to its raised position as shown in Figure 6. 3. Plug the Firefly ™ P200/P250 into an AC wall outlet (the POWER button will glow). 4. Audio input can be amplified by the P200/P250 and heard over the built-in speakers. Connect a stereo or mono audio source, such as the auxiliary ou[...]

  • Seite 13

    7. If you are using an IBM VGA/SVGA computer, the connections are shown in Figure 7: a. Unplug the monitor cable from the computer. b. Plug one end of the supplie d VGA/SVG A cable into the video port of the computer. c. Plug the other end of the VGA/ SVGA cable into the COMPUTER jack on the Firefly ™ P200/P250. d. To use your computer monitor al[...]

  • Seite 14

    8. If you are using a Macintosh computer, the connections are shown in Figure 8: a. Unplug the monitor cable from the computer. b. Plug the adapter labeled either “550093-0" or “550093-2" into the monitor port of the computer. c. Plug one end of the supplie d VGA/SVG A cable into the adapter on the computer. d. Plug the other end of t[...]

  • Seite 15

    Remote Control Battery The remote control requires one 9V alkaline battery installed as shown in Figure 9. A new battery should be installe d in the remote control unit under the following circumstances: • New remote control unit is received from the factory. • LED on the remote control no longer lights when keys are pressed, indicating a “de[...]

  • Seite 16

    OPERATION After you have connected the Firefly ™ P200/P250 as described in the P200/P250 Setup section of this manual, you are ready to begin using your P200/P250 LCD notebook projector. Basic Operation 1. Lift and rotate the mirror as shown in Figure 6. 2. Press POWER to turn on the P200/P250 LCD notebook projector. The keypanel will light up an[...]

  • Seite 17

    9. Press VOLUME to adjust the volume of the P200/P250 built-in speakers. NOTE: If you have an external powered speaker system plugged into the AUDIO OUT jack, turn it on and adjust the volume of that external system. (The level at the AUDIO OUT jack is controlled by VOLUME .) 10. Turn on and play the connected VCR, LaserDisc player, etc. 11. Press [...]

  • Seite 18

    14. After the Firefly ™ P200/P250 has cooled and the fans have stopped, you may unplug the P200/P250 from the AC wall outlet. NOTE: To use your computer and monitor without disconnecting them from the P200/P250, the P200/P250 must be plugged into an AC wall outlet. The MONITOR jack on the Firefly ™ P200/P250 requires power to operate the comput[...]

  • Seite 19

    CONTROLS The P200/P250 keypanel and Menu Mode On-Screen controls allow you to customize the projected image and enhance the appearance of your presentation. The function of each keypanel and on-screen control is described below and the keypanel is shown in Figure 11. Keypanel Con trols NOTE: All controls have on-screen graphics to indicate their re[...]

  • Seite 20

    NOTE: The Alignment controls are functional only when the P200/P250 is not in “menu” mode. MENU This key controls the display of the on-screen controls “menu.” If an on-screen controls “menu” item is displayed, pressing this key will make the display disappear (on-screen displays normally disappear after five seconds). To enter “menu?[...]

  • Seite 21

    Menu Mode On-Screen Controls INVERSE To access the INVERSE function, press and release MENU , then press either the up or down arrow key to “step” through the “menu” until INVERSE is displayed. Press either the right or left arrow key to switch between a positive and negative image. An on-screen graphic will indicate the INVERSE setting. WI[...]

  • Seite 22

    LAMP HOURS To access the LAMP HOURS function, press and release MENU , then press either the up or down arrow key to “step” through the “menu” until LAMP HOURS is displayed. An on-screen graphic will indicate the relative LAMP HOURS value. The LAMP HOURS value is based upon an expected average lamp life. As the P200/P250 is used, the lamp h[...]

  • Seite 23

    Illuminated Indicators POWER The POWER button glows red when the P200/P250 is plugged into an AC wall outlet and is ready to be turned on. Keypanel When the keypanel is lit, indicates that the P200/P250 is in operation; the projector lamp shoul d also be on. REPLACE LAMP When lit, REPLACE LAMP indicates that the LAMP HOURS value is zero. Refer to t[...]

  • Seite 24

    CARE AND MAINTENANCE Storage and Transportation To prepare your P200/P250 for transport, perform the following steps: 1. Press POWER to turn off the projector and lamp. (The fans will continue turning for approximately three minutes.) 2. When the fans have stopped turning and the P200/P250 is cool, unplug the power cord. 3. Close the P200/P250 down[...]

  • Seite 25

    3. Rotate and lower the mirror, then close the P200/P250 down to its storage position. 4. Turn the P200/P250 over on a flat, stable surface. NOTE: Typically, lamps have an average operating life of approximately 30 hours. When lit, REPLACE LAMP indicates that the P200/P250 has reached this average lamp operating life, and lamp failure may occur soo[...]

  • Seite 26

    6. Lift out the lamp/spare lamp compartment assembly. 7. Turn over the lamp compartment assembly and place it on a stable surface. 8. Rotate the retainer clip (Figure 12) and pull the active lamp out of the lamp holder. 9. Slide the spare lamp from its storage location. 10. Insert the spare into the lamp holder and rotate the retainer clip to its o[...]

  • Seite 27

    Troubleshooting Guide PROBLEM POSSIBLE SOLUTIONS Telex logo is displayed on Firefly ™ P200/P250 • Unit is working properly, but no video source is present. No image projected from Firefly ™ P200/P250 • Firefly ™ not turned on. • Firefly ™ not connected to AC wall outlet. • AC wall outlet defective. • Computer or video cable not se[...]

  • Seite 28

    PROBLEM POSSIBLE SOLUTIONS Split image or partial image • Image alignment needed; use up-down and left-right arrow keys. • Incompatible video signal from computer. • Reset the Firefly ™ to factory default settings. Power button not illuminated on keypanel • Firefly ™ not connected to AC wall outlet. • Defective AC wall outlet. No audi[...]

  • Seite 29

    PROBLEM POSSIBLE SOLUTIONS Image out of focus • Rotate the lens to adjust screen focus. • Adjust FOCUS control. NOTE: If only portions of the image are out of focus and the FOCUS adjustment causes the out-of-focus portions to move, refer to the solution described in the “vertical bars” problem. NOTE: Displaying a cross-hatch pattern will ai[...]

  • Seite 30

    SERVICE INFORMATION In the interest of promptness (if service is required), it is recommended that you first contact the dealer from whom the equipment was purchased. If modules are to be returned to the dealer or factory, they should be shipped in the original packing material or carefully packed in some other container with sufficient packing mat[...]

  • Seite 31

    TECHNICAL SPECIFICATIONS P200 Computer Compatibil ity • IBM and IBM compatibles with VGA (640 x 480) • Macintosh computers with external video (640 x 480 mode) • 800 x 600 mode supported by showing a 640 x 480 window of the larger image P250 Computer Compatibil ity • IBM and IBM compatibles with SVGA (800 x 600) • Macintosh computers with[...]

  • Seite 32

    Optical Lens • 140 mm focal length • f3.7 • Four element Dogmar lens Computer Video Requirements • Red, Green, Blue signal input/output (0 to 1.0V at 75 ohms impedance) • Vertical sync frequency: 50 - 72 Hz • Horizontal sync frequency: 31 - 40 kHz (P200) • Horizontal sync frequency: 31 - 48 kHz (P250) Composite Video Requirements NTSC[...]

  • Seite 33

    ABBREVIATIONS AUX Auxiliary B/W Black and white CCIR Comite Consultatif International des Radio Communications CD Compact disk CW Clockwise CCW Counter-clockwise DOS Disk operating system EP Extended play (same as SLP) FCC Federal Communications Commission LCD Liquid crystal display LED Light emitting diode LP Long play ME-SECAM Middle East SECAM N[...]

  • Seite 34

    A accessories .................. 3 adapter ................. 4 , 9 , 2 4 alignment ................. 14, 23 audio ................ 6 - 7 , 11, 23 B battery .................. 10, 18 BRIGHTNESS .............. 14, 22 C cleaning .................... 1 9 color ........... 2 , 14, 16 - 17, 22, 26 compatibility ................. 2 6 compatible ..........[...]

  • Seite 35

    fuse holder .................. 2 1 fuse replacement ............... 2 1 G GERMAN ................... 1 7 I incompatible .............. 2 2 - 2 3 indicators ................. 15, 18 INVERSE ................. 16, 22 K keypanel ............... 2 , 14, 23 L lamp ............. 11, 15, 20 - 21, 27 lamp access .............. 11, 19, 21 lamp holder .......[...]

  • Seite 36

    remote control ........... 3 - 4 , 10, 18 REPLACE LAMP ........ 15, 17 - 18, 20 RESET .............. 15, 17, 20, 24 S service .................... 2 5 settings ............. 11, 15 - 17, 22 setup ................... 6 , 1 1 SOURCE ................. 12, 15 SPANISH ................... 1 7 spare lamp .................. 2 1 storage ................ 19,[...]

  • Seite 37

    38109-676 Rev A March 1997[...]