Supermicro SBA-7142G-T4 Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80

Zur Seite of

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Supermicro SBA-7142G-T4 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Supermicro SBA-7142G-T4, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Supermicro SBA-7142G-T4 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Supermicro SBA-7142G-T4. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Supermicro SBA-7142G-T4 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Supermicro SBA-7142G-T4
- Den Namen des Produzenten und das Produktionsjahr des Geräts Supermicro SBA-7142G-T4
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Supermicro SBA-7142G-T4
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Supermicro SBA-7142G-T4 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Supermicro SBA-7142G-T4 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Supermicro finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Supermicro SBA-7142G-T4 zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Supermicro SBA-7142G-T4, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Supermicro SBA-7142G-T4 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    SBA-7142G-T4 Blade Module User ’ s Manual Revison 1.0d[...]

  • Seite 2

    SBA-7142G-T4 Blade Modu le User ’s Manual ii The information in th is User’s Manual has been carefully reviewed and is bel ieved to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notif y any pers[...]

  • Seite 3

    iii Preface About this Manual This manual is written for professional system integrators, Information T echnology professionals, service personnel and tech nicians. It provides information for the installation and use of the Supermicro SuperBlade ® system’s SBA-7142G-T4 blade module. Installation and maintenance should be performed by experience[...]

  • Seite 4

    SBA-7142G-T4 Blade Modu le User ’s Manual iv Notes[...]

  • Seite 5

    v Table of Contents Chapter 1 Introduction .............. .............. ........... .............. ........... ....... 1-1 1-1 Overview ................... ........... .............. ........... .............. ............ ............ 1-1 1-2 Product Checklist of T ypical Components ................... ........... ....... 1-1 1-3 Blade Mo dule Fe[...]

  • Seite 6

    SBA-7142G-T4 Blade Modu le User ’s Manual vi 3-4 Onboard Battery Inst allation ........... .............. ........... .............. .......... 3-5 3-5 Memory Installation .... ........... .............. ........... .............. ........... .......... 3-5 Populating Memory Slots .................... ............ ........... .............. .....[...]

  • Seite 7

    vii T able of Contents Remote Access Configuratio n .... ........... .............. ........... .............. .......... 5-8 Hardware Health Configuration........... ...... .............. ........... .............. ....... 5-9 ACPI Configuration .......... ........... .............. .............. .............. .............. .... 5-9 IPMI Config[...]

  • Seite 8

    SBA-7142G-T4 Blade Modu le User ’s Manual viii Notes[...]

  • Seite 9

    1-1 Chapter 1 Introduction 1-1 Overview The SBA-7142G-T4 blade module is a compact self-contained server that connects into a pre-cabled enclosure that provide s power , cooling, management and networking functions. One enclosure for the SBA-7142G-T4 blade module can hold ten blade units. In this manual, “blade system” refers to the entire syst[...]

  • Seite 10

    SBA-7142G-T4 Blade Modu le User ’s Manual 1-2 1-3 Blade Module Features T able 1-1 lists the main features of the SBA-7142G-T4 blade module. See the proceeding section for components typically included in a blade system and other optional components. S pecific det ails on the SBA-7142G-T4 blade module is found in Chapter 4: "Blade Module Fea[...]

  • Seite 11

    1-3 Chapter 1: Introduction Details on inst allation of memory modules into the SBA-7142G-T4 blade module are found in Chapter 3: "Setup and Installation" on page 3-1 . Sto r ag e The SBA-7142G-T4 blade module can have four 2.5" SA T A (Serial A T A) hard disk drives in front-mounted easy removable carriers. See Cha pter 3: "Set[...]

  • Seite 12

    SBA-7142G-T4 Blade Modu le User ’s Manual 1-4 1-4 Cont acting Supermicro Headquarters Address: Super Micro Computer , I nc. 980 Rock Ave. San Jose, CA 95131 U.S.A. T el: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (T echnical Sup port) Web S ite : www .supermicro.com Europe[...]

  • Seite 13

    2-1 Chapter 2 Standardized Warning Statements 2-1 About St andardized W arning St atement s The following statements are industry standard warnings, provided to warn the user of situations which have the potential for bodily inju ry . Should you have questions or experience difficulty , contact Supermicro's T echnical Support department for as[...]

  • Seite 14

    SBA-7142G-T4 Blade Modu le User ’s Manual 2-2 W arnung WICHTIGE SICHERHEITSHINWEISE Dieses W arnsymbol bedeutet Gefahr . Sie befinden sich in einer Situation, die zu V erletzungen führen kann. Machen Sie sich vor der Arbeit mit Ge räten mit den Gefahren elektrischer Schaltungen und den üblichen V erfahren zur V orbeugung vor Unfällen vertraut[...]

  • Seite 15

    2-3 Chapter 2: S t andardized W arning S tatement s 경고 ! 이 경고 기호는 위험이 있 음을 알려 줍니다 . 작업자의 신체에 부상을 야기 할 수 있는 상태에 있게 됩니다 . 모든 장비에 대한 작 업을 수행하기 전에 전기회로 와 관련된 위험 요소들을 확인하시고 사전에 사고를 방지[...]

  • Seite 16

    SBA-7142G-T4 Blade Modu le User ’s Manual 2-4 시스템을 전원에 연결하기 전에 설치 안내를 읽어주십 시오 . W aarschuwing Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit. Circuit Breaker Wa r n i n g ! This product relies on the building's inst allation for shor t-circuit (overcurren[...]

  • Seite 17

    2-5 Chapter 2: S t andardized W arning S tatement s 경고 ! 이 제품은 전원의 단락 ( 과전류 ) 방지에 대해서 전적으로 건물의 관련 설비에 의존합니 다 . 보호장치의 정격이 반드시 250V( 볼트 ), 20A( 암페어 ) 를 초과하지 않도록 해야 합니다 . W aarschuwing Dit product is afhankelijk van de ko[...]

  • Seite 18

    SBA-7142G-T4 Blade Modu le User ’s Manual 2-6 ¡Advertencia! El sistema debe ser disconnected de todas las fuentes de energía y del cab le eléctrico quitado de los módulos de fuente de alimentaci ón antes de tener acceso el interior del chasis para instalar o para quit ar componentes de sistema. Attention Le système doit être débranché de[...]

  • Seite 19

    2-7 Chapter 2: S t andardized W arning S tatement s W arnung Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem, qualifiziertem Personal gestattet werden. ¡Advertencia! Solamente el personal calificado debe instal ar , reemplazar o utilizar este equipo. Attention Il est vivement recommandé de confier l'installa[...]

  • Seite 20

    SBA-7142G-T4 Blade Modu le User ’s Manual 2-8 W arnung Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vor gesehen. Der Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und Schlüssel oder einer sonstigen Sicherheitsvorkehrung möglich. ¡Advertencia! Esta unidad ha sido diseñada para instalaci[...]

  • Seite 21

    2-9 Chapter 2: S t andardized W arning S tatement s Battery Handling Wa r n i n g ! There is the danger of explosion if the battery is replaced in correctly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries acco rding to the manufacturer's instructions. 電池の取り扱い ?[...]

  • Seite 22

    SBA-7142G-T4 Blade Modu le User ’s Manual 2-10 배터리가 올바 르게 교체되지 않으면 폭발의 위험이 있습니다 . 기존 배터리 와 동일하 거 나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다 . 제조사의 안내 에 따라 사용된 배터리를 처리 하여 주십시오 . W aa[...]

  • Seite 23

    2-1 1 Chapter 2: S t andardized W arning S tatement s 경고 ! 이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습 니다 . 이 장치에 전 원을 차단하기 위해서는 모 든 연결 단자를 제거해야만 합니다 . W aarschuwing Deze eenheid kan meer dan één stroomtoevoer aansluiting bevatten. Al[...]

  • Seite 24

    SBA-7142G-T4 Blade Modu le User ’s Manual 2-12 경고 ! 시스템이 동작 중일 때 후면판 (Backplane) 에는 위험한 전압이나 에너지가 발생 합니 다 . 서비스 작업 시 주의하십시오 . W aarschuwing Een gevaarlijke spanning of energie is aanwezig op de backplane wanneer h et systeem in gebruik is. V o orzichtighei d i[...]

  • Seite 25

    2-13 Chapter 2: S t andardized W arning S tatement s 경고 ! 현 지역 및 국가의 전기 규정에 따라 장비를 설치해 야 합니다 . W aarschuwing Bij installatie van de apparatuur moet worden voldaan aan de lokale en nat ionale elektriciteitsvoorschriften. Product Disposal Wa r n i n g ! Ultimate disposal of this product should be ha[...]

  • Seite 26

    SBA-7142G-T4 Blade Modu le User ’s Manual 2-14 경고 ! 이 제품은 해당 국가의 관 련 법규 및 규정에 따라 폐기되어야 합니다 . W aarschuwing De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen. Hot Swap Fan W a rning Wa r n i n g ! The fans might sti[...]

  • Seite 27

    2-15 Chapter 2: S t andardized W arning S tatement s 경고 ! 섀시로부터 팬 조립품을 제거할 때 팬은 여전히 회전하고 있을 수 있습니다 . 팬 조림품 외관의 열려있는 부분들로부터 손가락 및 스크류드라이버 , 다른 물체들이 가까이 하지 않도록 배치해 주십시오 . W aarschuwing Het i[...]

  • Seite 28

    SBA-7142G-T4 Blade Modu le User ’s Manual 2-16 W arnung Bei der Installation des Produkts, die zur V erfügung gestellten oder benannt Anschlusskabel, S tromkabel und Netzte ile. V erwendung anderer Kabel und Adapter kann zu einer Fehlfunktion oder ein Brand ent stehen. Elektrische Geräte und Material Safety Law verbietet die V erwendung von UL-[...]

  • Seite 29

    2-17 Chapter 2: S t andardized W arning S tatement s 경고 ! 제품을 설치할 때에는 제공되거나 지정된 연결케이블과 전원케이블 , AC 어댑터 를 사용 해야 합니다 . 그 밖의 다른 케이블들이나 어댑터들은 고장 또는 화재의 원인이 될 수 있 습니다 . 전기용품안전법 (Electrical Appl ia[...]

  • Seite 30

    SBA-7142G-T4 Blade Modu le User ’s Manual 2-18 Notes[...]

  • Seite 31

    3-1 Chapter 3 Setup and Installation 3-1 Overview This chapter covers the setup and installation of the blade module and its components. 3-2 Inst alling Blade Modules Up to ten SBA-7142G-T4 blade modules may be installed into a single blade enclosure (depending upon your enclosure and blade). Blade modules with Windows and Linux operating systems m[...]

  • Seite 32

    SBA-7142G-T4 Blade Modu le User ’s Manual 3-2 Removing/Replacing the Blade Cove r The blade cover must be removed to access the mainboard when you need to install or remove processors, memory units, the onboard battery and so on. Removing/Replacing the Blad e Cover 1. Remove the blade unit from the enclosure (see "R emoving a Blade Unit from[...]

  • Seite 33

    3-3 Chapter 3: Setup and Installation Figure 3-1. Inserting a Blade into the Enclosure Figure 3-2. Locking the B lade into Position[...]

  • Seite 34

    SBA-7142G-T4 Blade Modu le User ’s Manual 3-4 3-3 Processor Inst allation One to four 1944-pin G34 socket AMD Opteron 6100 series processors may be installed to the mainboard of the blade module. See Chapter 1 for ge neral information on the features of the blade unit and the Supermicro web site for further details inclu ding processor , memory a[...]

  • Seite 35

    3-5 Chapter 3: Setup and Installation 10. Replace the cover on the blade unit and finish by installing the unit back into the blade enclosure. Figure 3-3. Installing a G34 Processor in a Socket 3-4 Onboard Battery Inst allation A battery is included on the mainboard to s upply certain volatile memory components with power when power has been remove[...]

  • Seite 36

    SBA-7142G-T4 Blade Modu le User ’s Manual 3-6 Populating Memory Slot s The mainboard of a SBA-7142G-T4 blade module h as 16 memory slots. Both interleaved and non-interleaved me mory are supported, so you may popula te any number of DIMM slots. Populating slots at the same time with memory modules of the same size and of the same type will result[...]

  • Seite 37

    3-7 Chapter 3: Setup and Installation T a ble 3-1. Populating Memory Slots for Interleaved Operation Number of DIMMs CPU Channel 1 Channel 2 Channel3 Channel4 4 DIMMs CPU1 P1-DIMM1 CPU2 P2-DIMM1 CPU3 P3-DIMM1 CPU4 P4-DIMM1 8 DIMMs CPU1 P1-DIMM1 P1-DIMM2 CPU2 P2-DIMM1 P2-DIMM2 CPU3 P3-DIMM1 P3-DIMM2 CPU4 P4-DIMM1 P4-DIMM2 12 DIMMs CPU1 P1-DIMM1 P1-D[...]

  • Seite 38

    SBA-7142G-T4 Blade Modu le User ’s Manual 3-8 Figure 3-5. 16-Slot DIMM Numbering fo r Blade Module Edge of Board Toward CPU Toward CPU Edge of Board Toward CPU Toward CPU P1-DIMM2 P1-DIMM1 P1-DIMM3 P1-DIMM4 P3-DIMM3 P3-DIMM4 P3-DIMM2 P3-DIMM1 P4-DIMM2 P4-DIMM1 P4-DIMM3 P4-DIMM4 P2-DIMM3 P2-DIMM4 P2-DIMM2 P2-DIMM1[...]

  • Seite 39

    3-9 Chapter 3: Setup and Installation DIMM Inst allation WA R N I NG : Exercise extre me care when installing or removing DIMM modules to prevent any possible damage. Installing DIMM Memory Modules 1. Power down the blade module (see "Power ing Down a Blade Unit" on page 3-1 ). 2. Remove the blade from the enclosure and the cover from the[...]

  • Seite 40

    SBA-7142G-T4 Blade Modu le User ’s Manual 3-10 3-6 Hard Disk Drive Inst allation Hard disk drives are installed in “carriers” which are hot-swappable and can be removed or replaced without powering down the blade unit they reside in. A blade module needs a hard disk drive with an operati ng system installed to operate. WA R N I NG : T o maint[...]

  • Seite 41

    3-1 1 Chapter 3: Setup and Installation Figure 3-7. Installing a Hard Drive in a Carrier[...]

  • Seite 42

    SBA-7142G-T4 Blade Modu le User ’s Manual 3-12 3-7 Inst alling the Operating System An operating system (OS) must be inst alled on each blade module. Blades with Microsoft Windows OS and blades with Linux OS can both occupy and operate within the same blade enclosure. Refer to the SuperMicro web site for a complete list of supported operating sys[...]

  • Seite 43

    3-13 Chapter 3: Setup and Installation Refer to the manuals on your SuperBlade CD-R OM for further details on the Virtual Media (CD-ROM or Drive Redirection) se ctions of these two utility programs. 3-8 Management Sof tware System management may be performed with either of three software packages: IPMIview , SMCIPMItool or a W eb-based Management U[...]

  • Seite 44

    SBA-7142G-T4 Blade Modu le User ’s Manual 3-14 Notes[...]

  • Seite 45

    4-1 Chapter 4 Blade Module Features Figure 4-1. SBA-7142G- T4 Blade Unit Front View This chapter describes the SBA-7142G-T4 blad e unit. Installation and maintenance should be performed by experience d technicians only . See Figure 4-1 for a front view of th e blade unit and T able 4-1 for its features. Table 4-1. SBA-7142G-T4 B lade Unit Features [...]

  • Seite 46

    SBA-7142G-T4 Blade Modu le User ’s Manual 4-2 4-1 Control Panel Each blade has a similar control panel ( Figur e 4-2 ) with power on/off button, a KVM connector , a KVM button and four LEDs on the top front of the unit. The numbers mentioned in Figure 4-2 are described in T able 4-2 . Figure 4-2. Blade Cont rol Panel T able 4-2. Blade Co ntrol Pa[...]

  • Seite 47

    4-3 Chapter 4: Blade Module Features Power Button Each blade has its own power button so that in dividual blade units within the enclosure may be turned on or off independently of the others. Pre ss the power button (#1) to turn on the blade server . The power LED (#3) will turn green. T o turn off, press and hold the power button for >4 seconds[...]

  • Seite 48

    SBA-7142G-T4 Blade Modu le User ’s Manual 4-4 4-2 Mainboard The mainboard of the SBA-7142G-T4 blade unit is a proprietary design, which is based on the AMD SR5650 & SP5100 chipset. See Figure 4-4 for a blo ck diagram of this chipset, Figure 4-3 for a view of the BHQGE Mainboard and Figure 4-5 f or an exploded view diagram of the blade unit. F[...]

  • Seite 49

    4-5 Chapter 4: Blade Module Features Figure 4-4. BHQGE Block Diagram T a ble 4-4. BHQGE Mainboard Layout Item Description 1 CPU Sockets 2 DIMM Slots 3 S pace for 2.5” SA T A Hard Drive 4 Gbx Connector (for power and logi c to backplane) 5 TPM Connector 6 Onboard Battery 7 AMD SR5650 chipset 8 SP5100 Chipset 9 KVM Module includes USB T ype-A Conne[...]

  • Seite 50

    SBA-7142G-T4 Blade Modu le User ’s Manual 4-6 Jumpers The jumpers present on t he mainboard are used by the manufacturer o nly; there are no jumpers used to configure the operation of the ma inboard. CMOS Clear JBT1 is used to clear CMOS and will also cl ear any passwords. JBT 1 consists of two contact pads located near the BIOS chip (#10 in Figu[...]

  • Seite 51

    4-7 Chapter 4: Blade Module Features 4-3 Blade Unit Component s Figure 4-5. Exploded View of SBA-7142G-T4 Blade Module 1 2 2 2 2 3 3 3 4 4 4 4 5[...]

  • Seite 52

    SBA-7142G-T4 Blade Modu le User ’s Manual 4-8 Memory Support The SBA-7142G-T4 blade module each suppo rts up to 512 GB of ECC Registered DDR3-1600/1333/1066 SDRAM o r 64 GB of ECC Unbuffered DDR3-1600/1333/1066 SDRAM in sixteen DIMM sockets. See Section 3-5 for further details on mainboard memory installation. Hard Disk Drives The SBA-7142G-T4 bl[...]

  • Seite 53

    5-1 Chapter 5 BIOS 5-1 Introduction This document describes the AMI ® BIOS Setup utility for the SBA-7142G-T4 Blade Module. The AMI ROM BIOS is stored in a flash chip and can be easily up graded using a floppy disk-based program. Running Setup Note: Default settings are in bold text unless otherw ise noted. The BIOS setup options described in this[...]

  • Seite 54

    SBA-7142G-T4 Blade Modu le User ’s Manual 5-2 When you first enter the AMI BIOS Setup utility , you will see the M AIN M ENU screen. Y ou can always return to the M AIN M ENU by selecting the Main t ab on the top of the screen with the arrow keys. The M AIN M ENU screen provides you with a system overview , which includes the version, built date [...]

  • Seite 55

    5-3 Chapter 5: BIOS Boot Feature The menu options in the B OOT F EATURE submenu and their descriptions are shown in T able 5-1 . T a ble 5-1. Boot Feature Subm enu Menu Option Description Quick Boot This option allows BIOS to skip certai n tests while booting . This will decrease the time needed to boot the syst em. Options include Enabled o r Disa[...]

  • Seite 56

    SBA-7142G-T4 Blade Modu le User ’s Manual 5-4 Processor & Clock Options The menu options in the P ROCESSOR & C LOCK O PTI ONS submenu and their descriptions are shown in T able 5-2 . Advanced Chip set Control The menu options in the Advanced Chipset Control submenu and their descriptions are shown in T able 5-3 . T a ble 5-2. Processor &a[...]

  • Seite 57

    5-5 Chapter 5: BIOS Channel Interleaving This option enables Ch annel Interleaving. Options include Auto and Disabled. CS Sparing Enable This option reserves a spare memory rank in each node. Options inclu de Enabled and Disabled . Power Down Enable This option enables or disables the Power Down feature for your system. Bank Swizzle Mode This optio[...]

  • Seite 58

    SBA-7142G-T4 Blade Modu le User ’s Manual 5-6 IDE Configuration The menu options in the IDE Configura TION submenu and their descriptions are shown in T able 5-4 T a ble 5-4. IDE Configur ation Submenu Menu Option Description OnChip SA T A Channel This option enables or disables the on-chi p SA T A channel. OnChip SA T A T y pe This option specif[...]

  • Seite 59

    5-7 Chapter 5: BIOS PCI/PnP Configuration The menu options in the PCI/P N P C ONFIGURATION submenu and their descriptions are shown in T able 5-5 . S.M.A.R.T Self-Monitoring Analysis an d Reporting T echnology (SMAR T) can help predi ct impending drive f ailures. Select " Auto" to allow BI OS to aut o detect hard d isk drive support. Sele[...]

  • Seite 60

    SBA-7142G-T4 Blade Modu le User ’s Manual 5-8 Super IO Device Configuration The menu options in the S UPER IO C ONFIGURATION submenu and their descr iptions are shown in T able 5-6 . Remote Access Configuration The menu options in the R EMOTE A CCESS C ONFIGURATION submenu and their descriptions are shown in T able 5-7 . T able 5-6. Super IO Con [...]

  • Seite 61

    5-9 Chapter 5: BIOS Hardware Health Configuration The menu options in the H ARDWARE H EALTH C ONFIGURATION submenu and their descriptions are shown in T able 5-8 . ACPI Configuration The menu options in the ACPI C ONFIGURATION submenu and their descriptions are shown in T able 5-9 . IPMI Configuration The menu options in the IPMI C ONFIGURATION sub[...]

  • Seite 62

    SBA-7142G-T4 Blade Modu le User ’s Manual 5-10 Event Log Co nfiguration The menu options in the E VENT L OG C ONFIGURATION sub menu and their descrip tions are shown in T able 5-1 1 . Clear BMC System Event Log Use this option to clear all event s in the BMC System Event Log.  Set LAN Configuration This is the input for the SET LAN Configurati[...]

  • Seite 63

    5-1 1 Chapter 5: BIOS 5-4 Security Menu The menu options for the S ECURITY menu are shown in T able 5-12 . The AMI BIOS provides a Su pervisor and a User password. If you use both passwords, the Supervisor password must be set first. T able 5-12. Security Menu Menu Option Description Change Supervisor Password Select this option and press <E NTE[...]

  • Seite 64

    SBA-7142G-T4 Blade Modu le User ’s Manual 5-12 5-5 Boot Menu The menu options for the B OOT menu are shown in T able 5-13 . T able 5-13. Boot Menu Menu Option Description  Boot Device Priority Use this sub-menu to specify the boot device priorit y s equence for devi ces installed in your system. . 1st ~ Boot Devices These settings specify the [...]

  • Seite 65

    5-13 Chapter 5: BIOS 5-6 Exit Menu Select the E XIT t ab from AMI BIOS S ETUP U TILITY screen to enter the E XIT BIOS S ETUP screen. The options for the E XIT menu are shown in T able 5-14 . Y ou may also additionally press <E SC > to exit without saving or <F10> to save your settings and exit. 1st ~ Drive These settings specify the boo[...]

  • Seite 66

    SBA-7142G-T4 Blade Modu le User ’s Manual 5-14 Notes[...]

  • Seite 67

    A-1 Appendix A BIOS POST Codes A-1 BIOS POST Messages During the Power-On Self-T est (POST), the BIOS will check for problems. If a problem is found, the BIOS will activate an alarm or di splay a message. The following is a list of such BIOS messages. T a ble A-1. BIOS POST Messages BIOS Message Description Failure Fixed Disk Fixed disk is not work[...]

  • Seite 68

    SBA-7142G-T4 Blade Modu le User ’s Manual A-2 Previous boot incomplete - Default configuration used Previous POST did not complete successfully . POST loads default values and of fers to run Se tup. If the failure was caused by incorrect values and they are not corrected, the next boot will likely fail. On systems with control of wait states , im[...]

  • Seite 69

    A-3 : nnnn kB Extended RAM Passed Where nnnn is the amount of RAM in kilobytes successfully tested. nnnn Cache SRAM Passed Where nnnn is the amount of system cache in kilobytes successfully tested. nnnn kB Shadow RAM Passed Where nnnn is the amount of shadow RAM in kilobytes successfully tested. nnnn kB System RAM Passe d Where nnnn is the amount o[...]

  • Seite 70

    SBA-7142G-T4 Blade Modu le User ’s Manual A-4 A-2 BIOS POST Codes This section lists the POST (Power-On Self-T est) codes for the AMI BIOS. POST codes are divided into two categories: recoverable and terminal. Recoverable POST Errors When a recoverable type of error occurs durin g POST , the BIOS will display an POST code that describes the probl[...]

  • Seite 71

    A-5 : Bootblock Recovery Codes The bootblock recovery checkpoint codes are listed in ord er of execution in T able A-3 . T a ble A-3. Bootblock Recovery Error Codes Post Code Description E0h The onboard floppy controller if available is initia lized. Next, beginning the base 512 KB memory test. E1h Initializing the interrupt vector table next. E2h [...]

  • Seite 72

    SBA-7142G-T4 Blade Modu le User ’s Manual A-6 Uncompressed Initializa tion Codes The following runtime checkpoint codes are listed in order of execution in Ta b l e A - 4 . These codes are uncompressed in F0000h shadow RAM. FCh Next, erasing the flash ROM. FDh Next, programming the flash ROM. FFh Flash ROM programming was successful. Next, restar[...]

  • Seite 73

    A-7 : 1Ah The memory refresh line is toggling. C hecking the 15 second on/off time next. 2Bh Passing control to the video ROM to perform any required configuration before the video ROM test. 2Ch All necessary proc essing before passing cont rol to the video ROM is done. Looking for the video ROM next and passing control to it. 2Dh The video ROM has[...]

  • Seite 74

    SBA-7142G-T4 Blade Modu le User ’s Manual A-8 40h Preparing the descriptor tables next. 42h The descriptor tables are prepared. Entering protected mode for the memory test next. 43h Entered protected mode. Enabling interrupts for diagnostics mode next. 44h Interrupts enabled if the diagnostics switch is on. Initializing data to check memory wrapa[...]

  • Seite 75

    A-9 : 59h The Hit <DEL> message is cleared. The <W AIT ...> message is displayed. S tarting the DMA and interrupt controller test next. 60h The DMA page register test passed. Performing the DMA Controller 1 base register test next. 62h The DMA controller 1 base register test passed. Performing the DMA controller 2 base register test nex[...]

  • Seite 76

    SBA-7142G-T4 Blade Modu le User ’s Manual A-10 95h Initializing the bus option ROMs from C800 next. See the last page of this chapter for additional information. 96h Initializing before passing control to the adaptor ROM at C800. 97h Initialization before the C800 adapto r ROM gains control has completed. The adaptor ROM check is next. 98h The ad[...]

  • Seite 77

    A-1 1 : B1h Copying any code to specific areas. 00h Code copying to specific areas is done . Passing control to INT 19h boot loader next. T a ble A-4. Uncompressed Initializatio n Error Codes Post Code Description[...]

  • Seite 78

    SBA-7142G-T4 Blade Modu le User ’s Manual A-12 Notes[...]

  • Seite 79

    Disclaimer The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilitie s or syste ms, aircraft, aircraft devices, aircraft/emergency communication devices or other critica l systems whose failure to perform be reasonably expected to result in significant inju ry or loss of [...]

  • Seite 80

    SBA-7142G-T4 Blade Modu le User ’s Manual NOTES[...]