Stamina Products 20-1200 Bedienungsanleitung

Owner's M a nual 20-1200 Patent(s) pending MADE IN CHINA Product May V ary Slightly From Pictured. 2008, 03 Exercise ca n present a health risk. Con sult a physicia n bef ore beginning a ny exercise progra m with this equi pment. If you feel faint or dizzy , i mmedi ately discontinue use of this equi pment. Serious bodily injury ca n occur if [...]

T ABLE OF CONTENTS 2 Operation al In struction s 10 Storage 14 W arra nty 15 Product Parts Drawing 16 Parts List 17 Fax/Mail Ordering Form 19 Page Page Safety In struction s 2 Before Y ou Begin 4 Equipment W arning & Notice Labels 5 Hardware Identification Chart 6 Asse mbly In structions 7 M ainten a nce 10 W ARNING: SAFETY INSTRUCTIONS W ARNIN[...]

THAN K YOU FOR PURCHASING THE Studio T ower T o help you get started, we have pre-a sse mbled most of your Studio T ower at the fa ctory with the exce ption of those few parts left un a sse mbled for shi pping purpose s. Simply f ollow the few a sse mbly in struction s set forth in this ma nual. With regular workouts you will be getting your body i[...]

4 BEFORE YOU BEGIN 4 Locking Pin T op Be a m Push-Thru Bar Left Upright Wooden Barre Right Upright Exten sion Cushion Right Slider Spring Pin Locking Knob Wheel Ca p Ba se Fra me Outer Cover Main Fra me Round Sta nd THE FOLLOWING TOOLS ARE REQUIRED FOR ASSEMBL Y : Allen W rench (6mm) Combin ation Wrench Tha nk you for choosing the Studio T ower . W[...]

5 EQUIPMENT W AR NING & NOTICE LABELS This chart is provided to help identify the warning & notice labels on the Studio T ower . Plea se ta ke a moment to fa miliarize yoursel f with all of the warning & notice la bels. La bel is larger tha n a ctual size W AR NING LABEL(63) W1[...]

6 Part No. and De scri ption Qty 56 Nylock Nut (M8 x 1.25) 8 59 W a sher (M8) 12 61 Arc W a sher (M8) 4 47 Bolt, Button He a d (M8 x 1.25 x 50mm) 2 48 Bolt, Button He a d (M8 x 1.25 x 55mm) 2 49 Bolt, Button He a d (M8 x 1.25 x 60mm) 4 50 Bolt, Button He a d (M8 x 1.25 x 70mm) 4 45 Screw , Round He a d (M4 x 20mm) 4 HAR D W ARE IDENTIFICA TION CHAR[...]

ASSEMBL Y INSTRUCTIONS 7 Pla ce all parts from the box in a cleared area a nd position them on the floor in front of you. Re move all pa cking materials from your are a and pla ce the m ba ck into the box. Do not dispose of the pa cking materi als until a ssembly is completed. Rea d ea ch step carefully bef ore beginning. If you are missing a part [...]

ASSEMBL Y INSTRUCTIONS 8 STEP 3 Atta ch the WOODEN BARRE(13) to the LEFT and RIGHT SLIDERS(8, 10) with BUTTON HEAD BOL TS (M8x1.25x55mm)(49), LOCK W ASHERS(M8)(62), a nd ACOR N NUTS(M8x1.25)(55). Do not tighten the bolts until STEP 5. STEP 4 Note the correct position of the holes a nd EYEBOL TS(23) on the TOP BEAM(22) in the illustration a bove. In[...]

ASSEMBL Y INSTRUCTIONS 9 STEP 7 Refer to illustration step 7. Pla ce the MAIN FRAME(1) with the cushion side fa ce down. Atta ch the EXTENSION FRAME(5) to the MAIN FRAME(1) with BUTT ON HEAD BOL TS(M8x1.25x55mm)(48), W ASHERS(M8)(59), an d NYLOCK NUTS(M8x1.25)(56). STEP 8 Refer to illustration step 8. U nfold the EXTENSION FRAME(5) from the MAIN FR[...]

OPERA TIONAL INSTRUCTIONS WOODEN BARRE ADJUSTMENT T o adjust the height of the WOODEN BARRE(13). T urn the SPRING PINS(12) on the LEFT a nd RIGHT SLIDERS (8, 10) counter clockwise until the knob portion ca n be pulled. Pull both SPRING PINS(12) at the sa me ti me a nd slide the SLIDERS(8, 10) up or down to a djust. Relea s e the SPRING PINS(12) to [...]

OPERA TIONAL INSTRUCTIONS 11 Atta ch the PUSH-THRU BAR(26) to one of the a djustment holes in the UPRIGHTS(7, 9) with two LOCKING PINS(30). Atta ch the SECURING STRAP(32) to the EYEBOL T(23) on the top of the T OP BEAM(22). For some exercises, the PUSH-THRU BAR(26) should be up a nd secured in position with the SECURING STRAP (32). The PUSH-THRU BA[...]

PUSH-THRU BAR(26) When doing exercises that require the spring re sista nce to come from above the bar , atta ch the PUSH- THRU SPRING(34) to the loop on the upper side of the PUSH-THRU BAR(26) with the DOUBLE ENDED CLIP(38). Atta ch the other end of the PUSH-THRU SPRING(34) to one of the loops on the TO P BEAM(22) with the LINK(31). Refer to illus[...]

OPERA TIONAL INSTRUCTIONS SAFETY STRAP(37) Refer to the illustration. The SAFETY STRAP(37) must be used a s follows: When using the PUSH-THRU BAR(26) with the PUSH-THRU SPRING(34) atta ched from below f or bottom load exercise s, atta ch the SAFETY STRAP(37) to a nother side of the tower from the spring. Connect one end of the stra p to one of the [...]

ST ORAGE 14 Store the Studio T ower in a cle a n, dry pla ce. 1. 3. UNFOLD THE Studio T ower Remove the LOCKING K NOBS(19) from the UPRIGHTS(7, 9). With one ha nd on one of the HANDLE STRAPS(20) on the MAIN CUSHION(2), a nd one hand on the EXTENSION FRAME(5), slowly unfold a nd lower the MAIN FRAME(1) and EXTENSION FRAME(5). Lock the MAIN FRAME(1) [...]

LIMITED W ARRANTY MODEL 20-1200 W ARRANTY 15 Sta mina Products, Inc. warra nts that this product will be free from defects in materials a nd workma nshi p under normal use, service a nd proper operation for a period of 90 days on parts a nd upholstery a nd 5 years on the fra me from the date of the original purcha se from a n authorized retailer . [...]

PRODUCT P ARTS D RA WING BACK FRONT 16[...]

P ARTS LIST DIAG RAM# P ART NAME QTY 1 Main Fra me 1 2 Main Cushion 1 3 Ba se Fra me 1 4 Ba se Cushion 1 5 Extension Fra me 1 6 Extension Cushion 1 7 Left Upright 1 8 Left Slider 1 9 Right Upright 1 10 Right Slider 1 1 1 Slider Bushing 4 12 Spring Pin 2 13 Wooden Barre 1 14 Inner Cover 2 15 Outer Cover 2 16 Wheel Ca p 2 17 Ba se Sta nd 2 18 Round S[...]

P ARTS LIST DIAGRAM# P ART NAME QTY 48 Bolt, Button Hea d (M8 x 1.25 x 55mm) 2 49 Bolt, Button Hea d (M8 x 1.25 x 60mm) 4 50 Bolt, Button Hea d (M8 x 1.25 x 70mm) 4 51 Bolt, Hex Hea d (M6 x 1 x 20mm) 1 1 52 Bolt, Hex Hea d (M6 x 1 x 55mm) 4 53 Bolt, Flat Hea d (M6 x 1 x 15mm) 4 54 Acorn Nut (M6 x 1) 9 55 Acorn Nut (M8 x 1.25) 4 56 Nylock Nut (M8 x [...]

IMPORT ANT : Before filling out the f orm below ma ke sure you have the right information. Refer to the parts list to make sure you're ordering the right parts! Detach a nd Mail or Fax the Form Below Sta min a Products, Inc. P .O. Box 1071 Springfield, MO 65801-1071 IMPORT ANT : W e must have your phone number in order to proce ss the order! F[...]