Sony HDW-M2100P Bedienungsanleitung

HD DIGIT AL VIDEOCASSETTE PLA YER HD W -M2100 HD W -M2100P OPERA TION MANUAL [English] 1st Edition (Revised 5)[...]

W ARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. THIS APPARATUS MUST BE EARTHED. A VER TISSEMENT Afin d’éviter tout risque d’incendie ou d’électrocution, ne pas exposer cet appareil à la pluie ou à l’humi[...]

WARNING: THIS WARNING IS APPLICABLE FOR OTHER COUNTRIES. 1. Use the approved Power Cord (3-core mains)/Appliance Connector/Plug with earthing-contacts that conforms to the safety regulations of each country if applicable. 2. Use the Power Cord (3-core mains lead)/Plug conforming to the following ratings, which meets power supply voltage of each cou[...]

Table of Contents 1 Ta b le of Contents Chapter 1 Overview 1-1 Featur es ........................................................................................... 1-1 1-2 Example System Configuration .................................................... 1-3 Chapter 2 Location and Function of Pa r t s Chapter 3 Preparations Chapter 4 Pla yback 4-1 [...]

Ta b le of Contents 2 Table of Contents Chapter 7 UMID Functions 7-1 Overview of UMID Functions ....................................................... 7-1 7-2 UMID Output and Display ............................................................ 7-2 7-2-1 UMID Output Settings ........................................................... 7-2 7-2-2 UMID[...]

Chapter 1 Overview Chapter 1 Overview 1-1 1-1 Features Chapter 1 Overview The HDW-M2100/M2100P is a high-definition (HD) digital videocassette player based on the HDCAM format. This unit uses large scale integrated circuits for signal processing, and has a simple internal construction, allowing it to provide functionality at least equivalent to a c[...]

Chapter 1 Overview 1-2 Chapter 1 Overview 1-1 Features Basic operation buttons and jog/shuttle dial The basic buttons and jog/shuttle dial for VTR and editing operations are provided in the conventional VTR layout, ensuring continuity with conventional operating panels. Time data display This can be selected to display a CTL counter value, time cod[...]

Chapter 1 Overview Chapter 1 Overview 1-3 The following conceptual diagram shows an example of use. 1-2 Example System Configuration Digital cassette BVE-series editor Tape control HDSDI/Analog composite Audio monitor Analog composite/component Video monitor Audio/video server system SDTI (optional) HDSDI SDI Analog audio HDW-M2100/M2100P SDTI (opt[...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-1 2-1 Contr ol P anels There are three control panels, as follows: •U pper control panel • Lower control panel •S witch panel Chapter 2 Location and Function of P ar ts CTL/TC TC MENU Z 59.94 ON OFF KEY INHI FRONT REAR P ANEL SEL CONTROL P ANEL Upper control p[...]

Chapter 2 Location and Function of Parts 2-2 Chapter 2 Location and Function of Parts 2-1-1 Upper Contr ol P anel Z BET ACAM/SP BET ACAM SX MPEG IMX Digital BET ACAM 1(9P) 2(50P) RS-232C HDCAM POWER PHONES REMOTE EJECT 1 POWER switch 2 REMOTE buttons and RS-232C indicator 4 Format indicators 5 PHONES jack and control Cassette compartment 1 POWER sw[...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-3 2-1-2 Lower Contr ol P anel CTL/TC TC MENU 59.94 CTL/TC TC MENU 59.94 1 Audio control section (see page 2-4) 3 Menu control buttons (see page 2-5) 5 MULTI CONTROL knob and PUSH/ SHIFT indicator (see page 2-7) 6 RESET button (see page 2-7) 7 Search control section [...]

Chapter 2 Location and Function of Parts 2-4 Chapter 2 Location and Function of Parts 1 Audio control section 1 DISPLAY FULL/FINE button Pressing this button toggles the display mode of the level meters in the audio setting display section between FULL and FINE. FULL: The display covers the range –60 dB to 0 dB or –40 dB to +20 dB as selected u[...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-5 3 Audio monitor signal selection buttons (CH1 to CH4, and CUE) The buttons in the upper and lower rows select tracks to be output to the MONITOR OUTPUT L and R connectors on the connector panel or the PHONES jack on the upper control panel. The buttons in the uppe[...]

Chapter 2 Location and Function of Parts 2-6 Chapter 2 Location and Function of Parts 2-1 Contr ol P anels 4 Time data/menu display section 1 Time data display This displays indicators relating to time data and other indicators. Time data display area 1 Normally this displays a CTL count, time code value, or user bit value according to the setting [...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-7 DOLBY NR indicator This lights when the Dolby noise-reduction 1) circuit is functioning. Speed indication area This indicates the speed of a DMC playback. During a DMC playback, “DMC SPD” is displayed in time data display area 2. However, CONFI playback is not[...]

Chapter 2 Location and Function of Parts 2-8 Chapter 2 Location and Function of Parts 2 JOG button To use the search dial for playback in jog mode, press this button, turning it on. For details of playback in jog mode, see the description of the search dial 5 . 3 VAR (variable) button To use the search dial for playback in variable speed mode, pres[...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-9 PREROLL REW PLAY F FWD STOP STANDBY 1 PREROLL button 8 Tape transport control section 1 PREROLL button Press this button to cue up to the preroll point (before the IN point by the time set as the preroll time) on the tape. You can change or select the preroll time[...]

Chapter 2 Location and Function of Parts 2-10 Chapter 2 Location and Function of Parts q; Editing control section 1 DMC EDIT button Use this button to memorize the playback speed varied between –1 and +2 times normal speed, and carry out automatic playback or automatic editing using the memorized playback speed. 2 MEMORY indicator When memorizing[...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-11 7 LEARN button After setting a speed variation start point (STUNT IN point) and a speed variation end point (STUNT OUT point), pressing this button makes the tape start running. You can then use the search dial to vary the tape speed, which is automatically store[...]

Chapter 2 Location and Function of Parts 2-12 Chapter 2 Location and Function of Parts 1 Memory card slot Insert a memory card to update this unit’s firmware. You can save or load setup menu settings onto the memory card. For details on firmware update and setup menu reading/ storing, refer to the Maintenance Manual Volume 1. 2 Memory card ejecti[...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-13 AUDIO OUTPUT CUE CH1 OUT CH2 CH3 CH4 2-2 Connector P anel 1 Analog audio output section 1 AUDIO OUTPUT CH1 to CH4 (channels 1 to 4) connectors (XLR 3-pin, male) These connectors output analog audio signals for channels 1 to 4. 2 CUE OUT (cue audio output) connect[...]

Chapter 2 Location and Function of Parts 2-14 Chapter 2 Location and Function of Parts 1 REF. (reference) VIDEO INPUT connectors (BNC type) and 75 Ω termination switch Input a reference video signal. Input a three-valued (positive and negative) sync signal, a video signal with chroma burst (VBS) or a monochrome video signal (VS). When using the l[...]

Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-15 5 Power supply section 1 AC IN connector Use the optional power cord to connect this to an AC outlet. 2 Ground terminal Connect this to ground. 6 External device connectors 1 REMOTE 2 PARALLEL I/O(50P) connector (D-sub 50-pin) Connect remote control signals from [...]

Chapter 2 Location and Function of Parts 2-16 Chapter 2 Location and Function of Parts TIME CODE OUT TIME CODE OUT connector 7 Time code output section TIME CODE OUT connector (XLR 3-pin, male) This outputs the playback time code. By setting setup menu item 606, you can also output the time code from the internal time code generator locked to the p[...]

Chapter 3 Preparations Chapter 3 Preparations 3-1 The following example shows the connections with an HDW-2000/M2000/M2000P unit as a recorder, with this unit used as a player. 75 Ω 75 Ω REMOTE 1-IN(9P) REMOTE 1-OUT(9P) HDSDI OUTPUT SDI OUTPUT 3 (SUPER) HDSDI INPUT REF . VIDEO INPUT REF . VIDEO INPUT REF . VIDEO INPUT 3-1 Connections to Externa[...]

Chapter 3 Preparations 3-2 Chapter 3 Preparations 3-1-2 Connecting Reference Signals Connect reference signals as shown below. 3-1 Connections to External De vices • SDI OUTPUT • COMPOSITE • COMPONENT REF . VIDEO INPUT HDSDI OUTPUT 75 Ω HD video monitor SD video monitor HDW-M2100/M2100P 75 Ω termination switch: ON Reference signal[...]

Chapter 3 Preparations Chapter 3 Preparations 3-3 3-2 Setup The principal setup operations before operating this unit can be carried out using setup menus. The setup menus of this unit comprise a basic setup menu and an extended setup menu. The contents of these menus are as follows. Basic setup menu: • Items relating to the hours meter • Items[...]

Chapter 3 Preparations 3-4 Chapter 3 Preparations 3-3 Superimposed Character Inf ormation When the function menu item CHARA is set to ON, the video signal output from the HDSDI OUTPUT 3 (SUPER) connector, SDI OUTPUT 3 (SUPER) connector, or COMPOSITE VIDEO OUTPUT 3 (SUPER) connector contains superimposed character information, including time code, m[...]

Chapter 3 Preparations Chapter 3 Preparations 3-5 2 Time code reader drop frame mark (for 59.94i, 29.97PsF mode only) “.”: Indicates drop frame mode “:”: Indicates non-drop-frame mode 3 VITC field mark “ ” (blank): Fields 1 and 3 (for 59.94i, 29.97PsF mode) or fields 1, 3, 5 and 7 (for 50i, 25PsF mode) “ * ”: Fields 2 and 4 (for 59.[...]

Chapter 3 Preparations 3-6 Chapter 3 Preparations 3-4-1 Cassette T ypes This unit uses the following HDCAM cassettes for playback. HDCAM cassettes The unit can also play back the following cassettes. •D igital Betacam cassettes •M PEG IMX cassettes •B etacam SX cassettes •B etacam SP cassettes (metal tape) •B etacam cassettes (oxide tape)[...]

Chapter 3 Preparations Chapter 3 Preparations 3-7 3-4-3 Pre venting Accidental Recor ding of Shot Marks To prevent shot marks from being accidentally recorded on a tape, press in the red record inhibit plug on the cassette. Large cassette Small cassette Press in the red record inhibit plug. (“ON”) Return this plug to its original position to en[...]

Chapter 3 Preparations 3-8 Chapter 3 Preparations 3-5 Using a Memory Stic k When a Memory Stick is inserted in the VTR, the file data can be stored on the Memory Stick , which enables you to share data among cameras. Note Use a Memory Stick formatted with this VTR. It cannot be shared with other devices. For more details, refer to the Maintenance M[...]

Chapter 3 Preparations Chapter 3 Preparations 3-9 Notes • Prevent metallic objects or your finger from coming into contact with the terminal of the connecting section. •D o not attach any material other than the supplied label to the label space. •A ttach the label at the prescribed labeling position. Make sure the label is attached at the la[...]

Chapter 4 Playback Chapter 4 Playback 4-1 4-1 Playback This section describes playback of video and audio. 4-1-1 Preparations for Playback Switch and menu settings Z CTL/TC TC MENU 59.94 Audio monitor signal selection buttons (see page 2-5) : Select the audio channel(s) to be monitored. POWER switch: ‘ I ’ side (on) TCR setting (see page 8-2) :[...]

Chapter 4 Playback 4-2 Chapter 4 Playback 4-1 Playback Time data selection Displayed time data Use the CTL/TC setting in function menu HOME page to select one of CTL (control), time code, and user bit values. When you select time code, the data displayed is determined by the F6 (TCR) setting (LTC/AUTO/ VITC) in function menu page 1 as follows. Outp[...]

Chapter 4 Playback Chapter 4 Playback 4-3 Playback in jog mode In jog mode, you can control the speed of playback by the speed of turning the search dial. The playback speed range is ±1 times normal speed. The playback speed range can be ±3 times normal speed by changing the setting of setup menu item 116. To carry out playback in jog mode, use t[...]

Chapter 4 Playback 4-4 Chapter 4 Playback 4-1 Playback To return to normal-speed playback Press the PLAY button. To alternate between normal-speed playback and shuttle mode playback Set the search dial to the position corresponding to the desired shuttle playback speed, then switch between normal-speed playback and shuttle playback by pressing the [...]

Chapter 4 Playback Chapter 4 Playback 4-5 To perform continuous capstan override playback 1 Set setup menu item 111 (TSO PLAY) to TSO. 2 Hold down the DMC EDIT button and turn the MULTI CONTROL knob to select the playback speed. The selected playback speed is displayed in time data display area 2 on the lower control panel of this unit as well as i[...]

Chapter 4 Playback 4-6 Chapter 4 Playback 4-1 Playback Storing a varying playback speed in memory To store the playback speed for DMC playback, use the following procedure. 1 Press the DMC EDIT button, turning it on. 2 While playing back the recorded tape, press the ENTRY button and one of the following buttons simultaneously, to set the start and [...]

Chapter 4 Playback Chapter 4 Playback 4-7 3 Press the search dial or the SHUTTLE button or VAR button to enter shuttle/variable speed mode. The SHUTTLE/VAR indicator lights. Note Make sure that setup menu item 111 (TSO PLAY) is set to DIS. 4 Holding down the DMC EDIT button, turn the search dial, to set the initial speed at the playback start point[...]

Chapter 4 Playback 4-8 Chapter 4 Playback To start playback immediately after preroll Press the LEARN button. The LEARN button lights, and after preroll, DMC playback is carried out for the section from the speed variation start point, then playback continues at normal speed from the speed variation end point. To stop the tape during DMC playback P[...]

Chapter 5 Shot Mark Function Chapter 5 Shot Mark Function 5-1 This unit allows the use of shot marks. Shot marks are indications at desired points on a tape which enable faster cuing. Types of shot mark On this unit, you can write post marks by a button operation during playback, while stopped, or during a search. It is possible to modify or erase [...]

Chapter 5 Shot Mark Function 5-2 Chapter 5 Shot Mark Function This section describes the settings in the shot mark operation menu. Displaying the shot mark operation menu With the function menu HOME page showing in the menu display, hold down the MARK button, and press the F5 (MENU) button. The following menu appears on the monitor. GO1:SEARCH TYPE[...]

Chapter 5 Shot Mark Function Chapter 5 Shot Mark Function 5-3 This section describes the operations concerning reading and writing shot marks. Note that the following operations cannot be carried out by remote control. 5-3-1 Reading Shot Marks To read in shot marks With a cassette loaded, hold down the LIST button and press the F FWD or REW button.[...]

Chapter 5 Shot Mark Function 5-4 Chapter 5 Shot Mark Function Z ENTRY button LIST button 5-3 Shot Mark Operations 5-3-3 Shot Mark List Operations Displaying the shot mark list Hold down the ENTRY button and press the LIST button. All of the shot mark types for which item G02 in the shot mark operation menu is set to “ON” appear in the list. If [...]

Chapter 5 Shot Mark Function Chapter 5 Shot Mark Function 5-5 A virtual shot mark appears on the monitor as “V- MARK xxx” (xxx is the number). This is not written to the tape. After entering a virtual shot mark, if you change the cassette or power the unit off, it appears in the list as the first shot mark of the next group read in. Adding a me[...]

Chapter 5 Shot Mark Function 5-6 Chapter 5 Shot Mark Function 5-3 Shot Mark Operations 1 With no shot mark list displayed, hold the MARK button down for at least 2 seconds. The REC/ERASE indicator lights, indicating that you can rewrite or erase shot marks. 2 Display the shot mark list. 3 Turn the MULTI CONTROL knob to select on the list the shot m[...]

Chapter 5 Shot Mark Function Chapter 5 Shot Mark Function 5-7 Camera IDs SERIAL NUMBER 010001 DATE 1998.05.11 MODEL NAME DNW 0090 TIME 12.55.10 CASSETTE NUMBER 0095 ID1 AAAAAAAAAAAA SHOT NUMBER 0052 ID2 BBBBBBBBBBBB ID3 CCCCCCCCCCCC ID4 DDDDDDDDDDDD TCR 23:59:59:29 Recording time code First shot mark in the group NO. TIME CODE (---/180) SHOT MARK *[...]

Chapter 5 Shot Mark Function 5-8 Chapter 5 Shot Mark Function 5-3 Shot Mark Operations 5-3-6 Sorting Shot Marks Based on shot data recorded on the tape, you can separate the shot marks by cassette, and sort them in time code sequence. To sort the shot marks Use the following procedure. Z 1 3 2 1 With the shot mark list displayed, press the F5 (SETI[...]

Chapter 6 Tele-File 6-1 Chapter 6 Tele-File Chapter 6 T ele-File 6-1 Overview of T ele-File Functions Tele-File is a non-contact data carrier system. Tele-File enables data writing/reading between cassettes with memory labels and VTRs. It increases the efficiency of operations such as cuing up and playback, and source data management. Newly develop[...]

6-2 Chapter 6 Tele-File Chapter 6 Tele-File 6-2 Opening the T ele-File Menu Opening from the function menu Display page 5 of the function menu in the menu display section, and then press the F1 (TELE-F) button. The Tele-File menu opens. For details about the function menu, see Chapter 8 “Function Menu” (page 8-1). Opening automatically When set[...]

Chapter 6 Tele-File 6-3 Chapter 6 Tele-File 6-3 T ele-File Menu 6-3-1 Clip Data Display How to read the display Monitor display Menu display section Tele-File menu indicator Indicates that the menu display section is currently displaying the Tele-File menu. Data type indicator Indicates the type of data selected with the clip data display mode. The[...]

6-4 Chapter 6 Tele-File Chapter 6 Tele-File Setting display area Displays the setting of the currently selected data type, and a cursor (“ * ” or “>”). The meaning of the cursor symbols is as follows: *: Indicates that the mode is clip data display mode or attribute data display/modify mode, and that data is selected. >: Indicates tha[...]

Chapter 6 Tele-File 6-5 Chapter 6 Tele-File Monitor display Title The title (maximum 14 characters) set in attribute data display/modify mode. Selected clip number A 4-digit number representing the number of the selected clip (with the “*” cursor). Remaining memory percentage The percentage of remaining memory (user area) available for use. If [...]

6-6 Chapter 6 Tele-File Chapter 6 Tele-File Moving the cursor directly Regardless of the cursor’s current position, pressing one of the following buttons moves the cursor directly to the specified position in the same clip and displays the data. IN (video IN point) button: IN point data OUT (video OUT point) button: OUT point data MARK button: Cu[...]

Chapter 6 Tele-File 6-7 Chapter 6 Tele-File 6-3-3 Modifying Clip Data To modify clip data, put the unit into clip data display mode and then press the F2 (SELECT) button to put it into clip data modification mode (the cursor changes to “>”). The function assignments for menu items in clip data modification mode are as follows. Clip data modi[...]

6-8 Chapter 6 Tele-File Chapter 6 Tele-File To add and delete clips To add clips 1 Rotate the MULTI CONTROL knob to move the “*” cursor to the position where you want to insert the clip. 2 Press the F2 (SELECT) button. The unit enters clip data modification mode. 3 Press the F5 (INS LN) button. A confirmation message “INSERT CLIP OK?” appea[...]

Chapter 6 Tele-File 6-9 Chapter 6 Tele-File To set the set or modified data as other time data Press the F6 (SET TO) button and select the time data (cue point, IN point, or OUT point), and then press the F5 (SET) or F6 (SET NL) button. The position where the data is set differs as follows, depending on the button pressed. • F5 (SET): The data is[...]

6-10 Chapter 6 Tele-File Chapter 6 Tele-File To make comment settings Proceed as follows to make comment settings. 1 Select a clip. 2 Select comment. 3 Press the F2 (SELECT) button. The unit enters clip data modification mode. 4 Press the F2 (MODIFY) button. The data entry area begins to flash, and the data can be set. 5 Enter a character by rotati[...]

Chapter 6 Tele-File 6-11 Chapter 6 Tele-File 6-3-5 Displa ying and Modifying Attrib ute Data You can display and modify attribute data. The example below shows attribute data displayed on the monitor. Video final recording date The most recent date (year/month/day) on which video was recorded on the tape. Title The title (name assigned to Tele-File[...]

6-12 Chapter 6 Tele-File Chapter 6 Tele-File To modify attribute data You can modify the title, ID, administrator data, and write inhibit setting attributes. However, the attributes cannot be modified when the control mode is “remote.” The modification is not possible when the write inhibit setting is ON, either. Proceed as follows after settin[...]

Chapter 7 UMID Functions Chapter 7 UMID Functions 7-1 Chapter 7 UMID Functions The UMID (Unique Material Identifier) is a type of meta-data in video and audio materials. It has been internationally standardized in SMPTE Standard 330M. This unit supports recording and generation of UMIDs. The UMID is made up of a section called the “Basic” secti[...]

Chapter 7 UMID Functions 7-2 Chapter 7 UMID Functions This section explains how to output and display UMIDs. Note When the number of active scan lines for HD SDI output is set to 720P, output and displaying of UMID are not carried out. 7-2-1 UMID Output Settings You can choose to output UMIDs or not, and select either Basic UMID or Extended UMID wh[...]

Chapter 7 UMID Functions Chapter 7 UMID Functions 7-3 Note The function for converting unit count to UTC works only when the unit rate is 2 (24 frames), 3 (24/1.001 frames), 4 (25 frames), 6 (30 frames), or 7 (30/1.001 frames). For other unit rates, the unit rate number and unit rate are displayed in hexadecimal. 5 Altitude XXXXXXXXm: Altitude data[...]

Chapter 8 Function Menu Chapter 8 Function Menu 8-1 Chapter 8 Function Menu 8-1 Overview The function menu allows you to make frequently made settings, such as selection of input video signals and time code settings. 8-1-1 Function Menu Configuration The function menu consists of seven pages by factory default: the HOME page and six pages numbered [...]

Chapter 8 Function Menu 8-2 Chapter 8 Function Menu 8-1-2 Using the Function Menu To change a menu item setting To change a menu item setting, press the corresponding function button (F1 to F6) to display the desired setting in the lower part of the menu display. Each press of the button displays the next setting. When a menu item setting flashes M[...]

Chapter 8 Function Menu Chapter 8 Function Menu 8-3 8-2 Function Menu Item List The function menu has the following items. HOME page a) The selection of LTC or VITC depends on the setting of F6 (TCR) in function menu page 1 . Page 1 Item Setting F4 (CTL/TC) Selects the time data to display in time data display area 1 (see page 2-6) . TC: Playback t[...]

Chapter 8 Function Menu 8-4 Chapter 8 Function Menu Page 2 8-2 Function Menu Item List Item Setting F1 (V.PROC) F2 (VIDEO) Sets the HD/SD video signal output level (– ∞ to +3 dB). PRESET: Regardless of manually set values, the video signal is set to the standard level. Manual setting: With the displayed setting flashing, you can rotate the MULT[...]

Chapter 8 Function Menu Chapter 8 Function Menu 8-5 Page 3 Item Setting F1 (SYNC) Sets the HD output signal sync phase. Setting method With the displayed setting flashing, you can rotate the MULTI CONTROL knob to adjust the output signal sync phase across the range ±15 µs relative to this unit’s input reference signal. Adjust this item when you[...]

Chapter 8 Function Menu 8-6 Chapter 8 Function Menu Page 4 Page 5 Item Setting F1 (CAPSTN) Selects the number of fields for capstan lock in playback. In 59.94i, 29.97PsF mode 2F: The capstan servo locks in units of 2 fields. When playing back a tape that was recorded with composite source signals, a vertical shift in the video (H shift) occurs. (Wh[...]

Chapter 9 Setup Menus Chapter 9 Setup Menus 9-1 Chapter 9 Setup Menus This unit has the following setup menus. •B asic setup menu • Extended setup menu To access the extended setup menu, a setting on the internal SS-89 board is required. For details, refer to the Installation Manual. In this manual, both the basic setup menu items and extended [...]

Chapter 9 Setup Menus 9-2 Chapter 9 Setup Menus To display setup menus With the function menu HOME page showing in the menu display, press the F5 (MENU) button. The currently selected setup menu item is displayed in the menu display, with the menu item number flashing. For basic operations in the menu display, see page 2-5. 9-2 Setup Men u Operatio[...]

Chapter 9 Setup Menus Chapter 9 Setup Menus 9-3 To display a desired sub-item For a menu item having sub-items, you can select a desired sub-item as follows. 1 With a desired menu item selected, press the F2 (SELECT) button. The currently selected sub-item name flashes. 2 Turn the MULTI CONTROL knob to select a desired sub-item. Changing menu item [...]

Chapter 9 Setup Menus 9-4 Chapter 9 Setup Menus Resetting the menu settings to their factory default values (menu item B20) To reset the current active menu settings to their factory default values, proceed as follows. 1 Perform steps 1 to 3 of the procedure described in the section “To change the settings of menu items without sub-items” on pa[...]

Chapter 9 Setup Menus Chapter 9 Setup Menus 9-5 Line conversion mode Use the following procedure. When setup menu item 018 ACTIVE LINE SELECT is set to 1035 Select the conversion mode in setup menu item 916 ACTIVE LINE 1035 CONVERT MODE. 1080 k 1035 (CONV): Convert the active scan lines from 1080 to 1035, without changing the aspect ratio. 1080 k 1[...]

Chapter 9 Setup Menus 9-6 Chapter 9 Setup Menus To recall settings from a menu bank When recalling the settings saved in one of menu banks 1 to 3, set the corresponding one of menu items B01 RECALL BANK 1 to B03 RECALL BANK 3 to ON, then press F5 (SET) button. When you wish to recall the settings saved in menu bank 4, select menu bank-4 with menu i[...]

Chapter 9 Setup Menus Chapter 9 Setup Menus 9-7 9-3 Items in the Basic Setup Men u The basic setup menu contains the following items. In the “Settings” column of the table, the factory default settings are indicated by an enclosing box. Item number Settings 001 PREROLL TIME 0S ... 5S ... 30S: Set the preroll time to between 0 and 30 seconds. A [...]

Chapter 9 Setup Menus 9-8 Chapter 9 Setup Menus Item number Item name Settings 009 a) CHARACTER TYPE 011 a) CHARACTER V-SIZE SYSTEM FREQUENCY SELECT 9-3 Items in the Basic Setup Menu Determines the type of characters such as time code output from the COMPOSITE VIDEO OUTPUT 3(SUPER) connector, HDSDI OUTPUT 3(SUPER) connector, and SDI OUTPUT 3(SUPER)[...]

Chapter 9 Setup Menus Chapter 9 Setup Menus 9-9 Item number Item name Settings B01 RECALL BANK 1 Set to ON to recall menu settings from menu bank 1. B02 RECALL BANK 2 Set to ON to recall menu settings from menu bank 2. B03 RECALL BANK 3 Set to ON to recall menu settings from menu bank 3. B11 SAVE BANK 1 Set to ON to save current active menu setting[...]

Chapter 9 Setup Menus 9-10 Chapter 9 Setup Menus 9-4 Items in the Extended Setup Menu 9-4 Items in the Extended Setup Men u The extended setup menu contains the following items. In the “Settings” column of the table, the factory default settings are indicated by an enclosing box. Menu items in the range 100 to 199, relating to the control panel[...]

Chapter 9 Setup Menus Chapter 9 Setup Menus 9-11 Menu items in the range 100 to 199, relating to the control panels (Continued) Item number Item name Settings 111 TSO PLAY Select whether or not to enable tape speed override mode. DIS : Disable tape speed override mode. TSO: Enable tape speed override mode. 116 JOG DIAL RESPONSE Select the tape spee[...]

Chapter 9 Setup Menus 9-12 Chapter 9 Setup Menus 9-4 Items in the Extended Setup Menu Menu items in the range 100 to 199, relating to the control panels (Continued) Item number Item name Settings 119 VARIABLE SPEED LIMIT IN KEY PANEL CONTROL Select the playback speed range when carrying out playback in variable speed mode from the control panel of [...]

Chapter 9 Setup Menus Chapter 9 Setup Menus 9-13 201 Item number Item name Settings PARA RUN 202 Menu items in the range 200 to 299, relating to the remote control interface CF FLAG (Valid only in 50i or 25PsF mode.) Select the mode for locking to the color framing sent from the remote controller. 8F : Eight-field locking mode 4F/8F: Four- or eight[...]

Chapter 9 Setup Menus 9-14 Chapter 9 Setup Menus 9-4 Items in the Extended Setup Menu Menu items in the range 300 to 399, relating to editing operations Item number Item name Settings 301 VAR SPEED RANGE FOR SYNCHRONIZATION Select the playback speed range when carrying out playback in variable speed mode from a remote control unit connected to the [...]

Chapter 9 Setup Menus Chapter 9 Setup Menus 9-15 Menu items in the range 300 to 399, relating to editing operations (Continued) Menu items in the range 400 to 499, relating to preroll 337 EXTERNAL REFERENCE SELECT 338 OUTPUT AUDIO/TC PHASE Set the audio (AES/EBU and analog) and time code output phase. HD : Sync with HDSDI output phase. SD : Sync wi[...]

Chapter 9 Setup Menus 9-16 Chapter 9 Setup Menus 9-4 Items in the Extended Setup Menu Menu items in the range 500 to 599, relating to tape protection Menu items in the range 600 to 650, relating to the time code generator Item number Item name Settings 601 VITC POSITION SEL-1 (Invalid in 24PsF or 23.98PsF mode.) In 59.94i, 29.97PsF mode Select a li[...]

Chapter 9 Setup Menus Chapter 9 Setup Menus 9-17 Menu items in the range 600 to 650, relating to the time code generator (Continued) 602 VITC POSITION SEL-2 (Invalid in 24PsF or 23.98PsF mode.) In 59.94i, 29.97PsF mode Select a line to insert the VITC in. (For SD output) 12H to 18H to 20H: Select any line from 12 to 20. Note You can insert the VITC[...]

Chapter 9 Setup Menus 9-18 Chapter 9 Setup Menus 9-4 Items in the Extended Setup Menu Menu items in the range 600 to 650, relating to the time code generator (Continued) Menu items in the range 651 to 699, relating to the UMID Item number Item name Settings 621 24F STARTING TC SEL (In 50i or 25PsF mode only. Not displayed when operating in 720P-lin[...]

Chapter 9 Setup Menus Chapter 9 Setup Menus 9-19 Menu items in the range 700 to 799, relating to video control a) The “Y-add” function is a circuit operation to interpolate the video signal vertically during jog or variable speed playback for the purpose of reducing the vertical movement of the playback picture. Item number Item name Settings 7[...]

Chapter 9 Setup Menus 9-20 Chapter 9 Setup Menus 9-4 Items in the Extended Setup Menu Menu items in the range 700 to 799, relating to video control (Continued) Item number Item name Settings 709 CAV LEVEL FORMAT (Valid only in 59.94i or 29.97PsF mode.) Select whether the analog component output should be D-1 or Betacam. Format Color bars Y video Y [...]

Chapter 9 Setup Menus Chapter 9 Setup Menus 9-21 Menu items in the range 700 to 799, relating to video control (Continued) (Items 715 to 720: Settings for controlling the SD video processing system according to the menu settings.) Item number Item name 715 VIDEO GAIN CONTROL 716 CHROMA GAIN CONTROL 717 CHROMA PHASE CONTROL 718 SETUP LEVEL (59.94i, [...]

Chapter 9 Setup Menus 9-22 Chapter 9 Setup Menus 9-4 Items in the Extended Setup Menu Menu items in the range 700 to 799, relating to video control (Continued) Item name Settings Item number 726 H BLANKING WIDTH (Invalid in 24PsF or 23.98PsF mode.) Select the horizontal blanking width of the video output signal. NAROW : Digital blanking (narrow) WI[...]

Chapter 9 Setup Menus Chapter 9 Setup Menus 9-23 Menu items in the range 800 to 899, relating to audio control Item number Item name Settings 802 DIGITAL AUDIO MUTING IN SHUTTLE MODE Set the digital audio muting conditions during shuttle playback. OFF : Not muted. CUEUP: Muted during cue-up or preroll operations. FULL: Muted in shuttle mode. 801 DI[...]

Chapter 9 Setup Menus 9-24 Chapter 9 Setup Menus 9-4 Items in the Extended Setup Menu Menu items in the range 800 to 899, relating to audio control (Continued) Menu items in the range 900 to 999, relating to digital processing 824 ANALOG LINE OUTPUT SELECT Select the analog audio signals (tracks 1 to 8) to be assigned to audio output channels 1 to [...]

Chapter 9 Setup Menus Chapter 9 Setup Menus 9-25 Menu items in the range 900 to 999, relating to digital processing (Continued) 903 FREEZE MODE Select the freeze mode and timing. FIELD : Freeze a video field. Field may be odd or even, according to the timing. FLD1: Freeze an odd field. FLD2: Freeze an even field. FRM12: Freeze a frame consisting of[...]

Chapter 9 Setup Menus 9-26 Chapter 9 Setup Menus 9-4 Items in the Extended Setup Menu Menu items in the range 900 to 999, relating to digital processing (Continued) Item number Item name Settings 918 SLOW PROCESS MODE Switch the filter for increasing the vertical resolution during slow-motion playback on or off. ON: Increase the vertical resolution[...]

Chapter 9 Setup Menus Chapter 9 Setup Menus 9-27 Menu items in the range 900 to 999, relating to digital processing (Continued) Item number Item name Settings 942 V FILTER SELECT (Invalid in 24PsF or 23.98PsF mode.) Set the vertical interpolation filter coefficient for HD-SD converter output. The vertical resolution increases as the setting grows l[...]

Chapter 9 Setup Menus 9-28 Chapter 9 Setup Menus 9-4 Items in the Extended Setup Menu Menu items in the range 900 to 999, relating to digital processing (Continued) 961 BACKGROUND COLOR (UC) (Invalid in 24PsF or 23.98PsF mode.) Set the color of the part where no material exists (background) for up-converting. BACK GROUND COLOR: Set the color. BLACK[...]

Chapter 10 Maintenance and Inspection 10-1 Chapter 10 Maintenance and Inspection 10-1 Remo ving a Cassette When T ape Slac k Occur s If tape slack occurs in the unit, it is necessary to remove the upper lid and sound baffle. This job should always be entrusted to a technician who has undergone service training. To clean the video heads and audio he[...]

10-2 Chapter 10 Maintenance and Inspection Chapter 10 Maintenance and Inspection 10-3 Err or Messa ges Z ALARM indicator This unit is equipped with a self-diagnosis function, and if a problem is detected, displays an error message in the time data display and on the monitor. If an error message appears, contact your Sony service representative. Ind[...]

Chapter 10 Maintenance and Inspection 10-3 Chapter 10 Maintenance and Inspection Error Message List Code Message Description – NO COMMUNICATION Abnormality in the interface between the lower control panel (KY-464/465 board) and SYS CPU (SS-89 board) has been detected on the lower control panel side. 01 REEL TROUBLE Tape slacking has been detected[...]

10-4 Chapter 10 Maintenance and Inspection Chapter 10 Maintenance and Inspection 10-4 Moisture Condensation When the unit is suddenly moved from a cold to a warm location, or used in a very humid place, moisture from the air can condense on the head-drum. This is called moisture condensation. If the tape is run in this state, it can adhere to the d[...]

Chapter 10 Maintenance and Inspection 10-5 Chapter 10 Maintenance and Inspection 10-5 Regular Chec ks 10-5-1 Digital Hours Meter The digital hours meter can display seven items of information, in corresponding display modes, about the operational history of the unit. Use it as a guide in scheduling periodic maintenance. Display modes of the hours m[...]

10-6 Chapter 10 Maintenance and Inspection Chapter 10 Maintenance and Inspection Note Contact a Sony service or marketing representative regarding the replacement and checking of components. Component Digital hours meter indication (menu number in parenthesis) Guideline replacement intervals R: Replace C: Check, and replace if necessary 1000 hrs 20[...]

Appendix Appendix A-1 Specifications General Recording format HDCAM Power requirements 100 to 240 VAC, 50/60 Hz Power consumption 2.2 A (220 W), when used without optional devices Peak inrush current (1) Power ON, current probe method: 50 A (240 V), 14 A (100 V) (2) Hot switching inrush current, measured in accordance with European standard EN55103[...]

Appendix A-2 Appendix Specifications Variable speed mode HDCAM playback: –1 to +2 times normal playback speed Digital Betacam playback: –1 to +3 times normal playback speed MPEG IMX playback: –1 to +3 times normal playback speed Betacam SX playback: –1 to +2 times normal playback speed Analog Betacam playback: –1 to +3 times normal playba[...]

Appendix Appendix A-3 Digital Betacam playback Video Digital Audio (CH1 to CH4) Analog Audio (cue track) MPEG IMX playback Video Digital audio (CH1 to CH4) Betacam SX playback Video Digital Audio (CH1 to CH4) Bandwidth Y0 to 5.75 MHz +0.5 dB/–0.5 dB K factor R–Y/B–Y 0 to 2.75 MHz +0.5 dB/–0.5 dB S/N ratio 62 dB or more 1 % or less Frequency[...]

Appendix A-4 Appendix Specifications Analog Betacam playback Video Audio a) Reference level: +4 dBm Metal tape Oxide tape Frequency response (at 10 dB below reference level a) ) 50 Hz to 15 kHz +1.5 dB/ –3.0 dB 50 Hz to 15 kHz +3.0 dB S/N ratio (at 3% distortion level) 72 dB or more 50 dB or more (Dolby NR off) Distortion (THD at 1 kHz reference [...]

Appendix Appendix A-5 AUDIO OUTPUT CH1/2/3/4 XLR 3-pin, male (4) +4 dBm at 600 Ω load, low impedance, balanced AUDIO OUTPUT (AES/EBU) CH1/2, 3/4, 5/6, 7/8 BNC (4) Complies with AES-3id-1995 CUE OUT XLR 3-pin, male (1) +4 dBm at 600 Ω load, low impedance, balanced MONITOR OUTPUT (L/R) XLR 3-pin, male (2) +4 dBm at 600 Ω load, low impedance, ba[...]

Appendix A-6 Appendix Specifications Relation between HKDV-900/503 setting items and setup menu of this unit HKDV-900/503 setting items Setup menu items of this unit HD Master 740: MASTER LEVEL (HD) a) HD Y 741: Y LEVEL (HD) a) HD Pb 742: Pb LEVEL (HD) a) HD Pr 743: Pr LEVEL (HD) a) HD Setup 745: SETUP LEVEL (HD) a) HD Sync Phase 746: SYNC PHASE (H[...]

Appendix Appendix A-7 HD/SD video output phase settings For the HD/SD video output phase setting, you can use the maintenance menu. For details, refer to the Installation Manual. Item number Item name Settings M3 M3A: OUTPUT PHASE SELECT M3A0: HD PHASE SEL Select the HD video output signal phase with respect to the reference signal: 0H or –90H (H[...]

Index I-1 Index Index A AC IN connector 2-15 ALARM indicator 2-9 Analog audio output section 2-13 video input/output section 2-13 Audio control section 2-4 monitor signal output section 2-16 monitor signal selection buttons 2-5 setting display section 2-4 AUDIO OUTPUT (AES/EBU) connectors 2-14 AUDIO OUTPUT CH1 to CH4 connectors 2-13 B Basic setup m[...]

Index Index I-2 Index REMOTE 2 PARALLEL I/O(50P) connector 2-15 RESET button 2-7 REW button 2-9 RS-232C connector 2-15 indicator 2-2 S SC (function menu) 8-5 SDI OUTPUT connectors 2-14 SDTI OUTPUT connectors 2-14 Search control section 2-7 Search dial 2-8 SERVO indicator 2-9 Setup 3-3 SETUP (function menu) 8-4 Setup menu basic menu items 9-7 config[...]

The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenan[...]

 2001 HDW-M2100/M2100P (SY) 3-206-137- 15 (1) Sony Cor por ation[...]