SmartBridges sB3415-01 Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75

Zur Seite of

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung SmartBridges sB3415-01 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von SmartBridges sB3415-01, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung SmartBridges sB3415-01 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung SmartBridges sB3415-01. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung SmartBridges sB3415-01 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts SmartBridges sB3415-01
- Den Namen des Produzenten und das Produktionsjahr des Geräts SmartBridges sB3415-01
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts SmartBridges sB3415-01
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von SmartBridges sB3415-01 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von SmartBridges sB3415-01 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service SmartBridges finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von SmartBridges sB3415-01 zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts SmartBridges sB3415-01, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von SmartBridges sB3415-01 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    Copy ri ght © s m a rtBri dges Pt e Ltd. A l l Rights Reserv ed. u n w i r i n g o u r w o r l d TM airClien t™ TOTAL 241 Series sB3415-01 / sB3415-02 / sB3415-03 User Guide Version 2.1[...]

  • Seite 2

    Page 2 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide CONTENTS ABOUT THIS DOCUMENT .......................................................................................................... 4 Overview of User Guide ...................................................................................................... 4 Rela[...]

  • Seite 3

    Page 3 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 5.8. F IRMWAR E U PGRADE .................................................................................................... 66 5.9. P RODUCT L ICENSE K EY ............. ................................................................................... 68 5.10. L INK [...]

  • Seite 4

    Page 4 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Congratulations on your pu rchase of sB product Your airClient™ TOTAL 241 unit is designed so that you ca n set it up easily and be on your way to get unwired. Important: Read all user instructions carefully before you use your device. About This Document This user gu[...]

  • Seite 5

    Page 5 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Chapter 5: • The site survey tool • The s ystem configuratio n tools • Backup/restore features • Firmware upgrade steps • Using the License Key feature for bandwidth upgrade on the unit. The abbreviations and acronyms used in this u ser guide are explained in [...]

  • Seite 6

    Page 6 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 1. Introduction This user manual will guide you through initial site prepar ation, installati on, configuration, and troubleshooting of t he airClient TOTAL 241 [sB3415] unit. A web-based management tool is provided to assist the user to configure the airClient TOTAL un[...]

  • Seite 7

    Page 7 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 1.2. Checklists Deployment time, link-up time and support time can be improved by adopting proper site survey analysis, link planning, pre-installation tests, and web-GUI fam iliarization. The follow ing pre-installation and post- installation checklist attempts to give[...]

  • Seite 8

    Page 8 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide No Para met ers Units Site A Site B 18 Length of e xternal cable c onnecting Radio a nd antenna Feet/m eters 19 Fade Margin ta ken into account for link budgeti ng Ideal ly between 15 to 20 dB 20 Model of smartBridges airCl ient TOTAL equipment se lected for a link. Pl [...]

  • Seite 9

    Page 9 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Post-Installation Checkli st for airClient TOTAL Organization Name/Site Name Addr ess City State Zip Code Telephone N umber General Configuration Informat ion No Parameters Units Site A Site B sB3415-01 / sB341 5-02 : Router / NA T 1 Radio ope ration mode sB3415-03 : Br[...]

  • Seite 10

    Page 10 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Chec klist No Parameters Units Site A Site B 1 Chec k the crimpin g of the Et hernet ca ble at both the ends Yes /N o 2 Check the p roper g ro und ing of th e ant e nn a and equipment Yes /N o 3 Ensure that there are no ext reme bends or kinks in the ca ble Yes /N o 4 [...]

  • Seite 11

    Page 11 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 2. airClient TO T AL Configuration The airClient TOTAL sB3415-01 and sB3415-02 can w ork in either Router or NAT mode. The airClient TOTAL sB3415-03 can work in one of the three modes: Bridge, Router or NAT. The procedures for configuring the various parameters in ea c[...]

  • Seite 12

    Page 12 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Figure 2-2 airClient TOTAL Lice nse Agreement Page[...]

  • Seite 13

    Page 13 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Figure 2-3 airClient TOTAL Summary Information Page[...]

  • Seite 14

    Page 14 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide The descriptions of the fields in the Summary Information page ar e provi ded i n the t able (Ta ble 2-1 ) below: Table 2-1 Description of the field item s in the ‘Summary Information’ page Field Items on Summary Info page Descriptions LAN IP Mode Set to Static I P[...]

  • Seite 15

    Page 15 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 2.2. Web GUI Administrator Us er Name and P assword Change The default administrator user name for th e airClient TOTAL 3415 is adminis trator and administ rator password is smartBridges (please n ote that this is case sen sitive). Follow the steps below to change th e[...]

  • Seite 16

    Page 16 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 2.3. Using the Conf iguration Pages The airClie nt TOTAL co nfiguration system co mprises sever al pag es for config uring each paramete r. A common navigation menu bar is provided at the top of each page for ea sy navigation as shown in the figure below (Figure 2-5). [...]

  • Seite 17

    Page 17 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Menu Item Menu Sub-items Description Wireless Statisti cs Displays traffic s tatistics on the Wirele ss side Ass ociat ion St atus Shows the status of the association and the MA C of th e AP ass o c i at ed wi t h. Sho ws the Link Status Gr aph for t he associated link[...]

  • Seite 18

    Page 18 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Menu Item Menu Sub-items Description Note : By default, the Security mode is Disabled. AES sec urity mod e is only ava ilable in 3415-03 model . System Configuration Allows user to sw itch the operation mode between Bridge (sB3415 -03 Only), Router o r NAT mode . Allow[...]

  • Seite 19

    Page 19 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Menu Item Menu Sub-items Description Technical Support Information on Technical Support User Guide – Online Link to online user guide Product Registration and Feedback Allo ws user t o regis ter prod uct and provide feedback or suggestions. Check for Update s Ch ecks[...]

  • Seite 20

    Page 20 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 2.4. Device Mode Configuration The device operational mode is displayed a t the top right hand corner of each page. The de vice mode configuration allows the user to con figure the airClient TOTAL to a NAT (Network Add ress Translation) mode or Router mode for 3415 -01[...]

  • Seite 21

    Page 21 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 2.5. Changing from NAT to Router Mode The default configuration of the airClient TOTAL is in the NAT mode. Follow the steps below to change th e airClient TOTAL from the default NAT mode to Router mode: 1. From the navigation menu bar, click on Tools | System Configura[...]

  • Seite 22

    Page 22 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 2.6. Changing from Ro uter to NAT Mode Follow the steps below to change the airClient TOTAL from Router Mode to NAT Mode : 1. From the navigation me nu bar, click on Tools | System Configura tion . The System Configuration screen will appear as shown below. 2. Un der t[...]

  • Seite 23

    Page 23 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 3. Click on Save to conver t the unit to Bridge mode. 4. The Bridge Mode on sB3415 can be configured to operate in WDS and non-WDS modes. For all the different modes configuratio n in Bridge Mode, refer to Section 2.9. Figure 2-9 Changing Router/NAT Mode t o Bridge Mod[...]

  • Seite 24

    Page 24 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Figure 2-10 Changing Br idge Mode to Router (or NAT) Mode ( sB3415-03 Only)[...]

  • Seite 25

    Page 25 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 2.9. airClient TOTAL Bridge Configuration (sB 3415-03 only) This section is only valid for the sB3415-03 model. The sB3415-03 can be configured in b oth WDS and non-WDS mo des, while in Bridge Mode. In WDS mode, 3415 functions as a tra nsparent bridge. In non-WDS clien[...]

  • Seite 26

    Page 26 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Figure 2-11 airClient TOTAL WDS Bridge M ode Configuration (sB34 15-03 Only) LAN Settings This section outlines the procedures for changing the IP settings for bridge mode – 1. From the navigation menu bar, click on Home | LAN Set tings to change Ethernet/wired side [...]

  • Seite 27

    Page 27 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Figure 2-12 airClient TOTAL Bridge LAN Settings (sB3415-03 Only) Radio Settings Follow the steps below to config ure the Radio parame ters in the airClient TOTAL WD S Bridge Mode : 1. From the navi gation menu bar, click on Radio | Wire less Settings to set the radio p[...]

  • Seite 28

    Page 28 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Figure 2-13 airClient TO TAL WDS Bridge Radio Settings (s B3415-03 Only) Figure 2-14a airClient TOTAL Su mmary Information Page Figure 2-14b airClient TOTAL Wireless Association Status[...]

  • Seite 29

    Page 29 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 2.9. 2. Client Bridge Mode (Non-WDS) The sB3415-03 can also be configured to operate in the non-WDS Bridge Mode. It is said to be operating in the Client Bridge mode in this configuration. Th e airClient TOTAL can associate with any Access Point in this bridge mode. Th[...]

  • Seite 30

    Page 30 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Figure 2-15 airClient TOTAL Non-Trans parent bridging Configuration (sB3415-03 Only) LAN Settings This section outlines the procedures for changing the IP setting s for bridge mode. These settings are the same in all possible bridge modes – 1. From the navigation men[...]

  • Seite 31

    Page 31 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Figure 2-16 airClient TOTAL Bridge LAN Settings (sB3415-03 Only) Radio Settings Follow the steps below to configure the Radio param eters in the airClient TOTAL Bridge Mode, for Non- Transparent bridging : 1. From the navi gation menu bar, click on Radio | Wire less Se[...]

  • Seite 32

    Page 32 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Figure 2-17 airClient TOTAL Bridge Ra dio Settings – Non-Transparent bridging (sB3415- 03 Only) Note : In non-transparent bridging configuration, when airClient TOTAL is associated, the MAC addresses seen on the AP Association table, will be the MAC address of the sB[...]

  • Seite 33

    Page 33 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Figure 2-18 airClient TOTAL Transpare nt Bridging Configuration (sB3415-03 Only) LAN Settings This section outlines the procedures for changing the IP setting s for bridge mode. These settings are the same in all possible bridge modes – 1. From the navigation men u b[...]

  • Seite 34

    Page 34 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Figure 2-19 airClient TOTAL Bridge LAN Settings (sB3415-03 Only) Radio Settings Follow the steps below to configure the Radio para meters in the airClient TOTAL Bridge Mode, for Transparent bridging : 1. From the navi gation menu bar, click on Radio | Wire less Setting[...]

  • Seite 35

    Page 35 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Figure 2-20 airClient TOTAL Bridge Radio Settings – Transparent bridging (sB3415-03 Only) Note : In Tr anspare nt brid ging c onfigur ation , when ai rCli ent TO TAL is ass ociat ed, the MA C addr ess seen on the AP Association table, will be the MAC address of the d[...]

  • Seite 36

    Page 36 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 2.10. airClient TOTAL Rout er / NAT Configuration This section covers the procedures for configuring v arious parameters in the Router and NAT modes. 2.10.1. LAN Settings The LAN and the WLAN settings are ma intained in two different subnets. Follo w the st eps bel ow [...]

  • Seite 37

    Page 37 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 2.10.2. WLAN Settings The wi reless parame ters ne ed to be co nfigur ed to all ow the ai rClie nt TOTAL u nit to ass ociat e with an airPoint™ Nexus device or any other third party wireless access point. Follo w the st eps belo w to conf igure t he airCli ent T OTAL[...]

  • Seite 38

    Page 38 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Figure 2.23 airClient TOTAL Router/NAT WLAN Se ttings – Dynamic WLAN Connection For the airClie nt TOTAL d evice to a ssociate with an access point, th e user also ne eds to configure the access point’s SSID, security (if used), and select External/Internal antenna[...]

  • Seite 39

    Page 39 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Follo w the st eps bel ow to conf igur e the air Client TOTAL Ro uter/N AT Mode wireles s ass ociat ion parameters: 1. From the navigation menu bar, click on Radio | Wireless Sett ings to set the S SID and w ireless mode (802.11 b/g). The Wireless Settings screen w ill[...]

  • Seite 40

    Page 40 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Figure 2-24 airClient TOTAL Route r Wireless Settings Figure 2-25a airClient TOTAL Summary Information page[...]

  • Seite 41

    Page 41 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Figure 2-25b airClient TOTA L Wireless Associat ion Status Figure 2-25c airClient TOTAL Association Sta tus Graph Noise Floor is the measurement of the signal created from the sum of all the no ise sources and unwanted sign a ls wit hin a m easur ement s ystem . Note :[...]

  • Seite 42

    Page 42 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 2.10.3. DHCP Configurations The airClient TOTAL unit can be used as a DHCP server. DHCP ( Dynamic Host Configuration Protocol) allows a host to be a utomatically assigned a n ew IP address out of a pool of preconfig ured IP addresses for the network. This feature will [...]

  • Seite 43

    Page 43 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Figure 2-26 airClient TOTAL DHCP Server Configurations Figure 2-27 airClient TOTAL DHCP List Follow the steps below to disable the airClient TOTAL Rout er/NAT DHCP server : 1. From the Navigation menu b ar, click on Networking | DHCP Server to access t he DHCP conf igu[...]

  • Seite 44

    Page 44 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Figure 2-28 D isable DHCP and DHCP Relay 2.10.4. DHCP Relay Configuration If the user has a DHCP Server, the airClient TOTAL Router can be configured as a DHCP Relay agent of the DHCP Serve r for IP address assignm ent. Follow the steps below to configure the airClient[...]

  • Seite 45

    Page 45 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 2.10.5. IP/Port Forwarding IP/Port forwarding (also referred to as Virtual Server in this d ocument) allow s the user to define the po rt mapping between the local area network and the public network. This feature is only available when the device is configured in the [...]

  • Seite 46

    Page 46 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Figure 2-31 IP/Port Forwarding Table Entries on Summary Page Follow the steps be low to edit or delete a po rt forwarding entry in the airClient TOTAL operating in NAT Mode. 1. Click on Networking | IP/Port Forwarding from the menu bar to access the Port Fo rwarding Ta[...]

  • Seite 47

    Page 47 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Adding and deleting static routes is allowed in the Router Mode of the airClient TOTAL . Follow the steps below to add a static route entry in the airClient TOTAL operating in the Router Mode. 1. Click on Networking | Routing Table from the menu bar to access the routi[...]

  • Seite 48

    Page 48 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Follow the steps below to edit or delete a static rout e entry in the airClient TOTAL operating in the Router Mode. 1. Click on Networking | Routing Table from the menu bar to access the view routing tab le page. 2. From t he Routing table on this page, select the rout[...]

  • Seite 49

    Page 49 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 2.11. Security This section allows you to configure wireless encryption to prevent unauthorized parties from accessing the network. The security options on the airClient TOTAL are as follows: 1. Open System 2. Shared Key 3. WPA –PSK Note : By default, secu rity is Di[...]

  • Seite 50

    Page 50 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Figure 2-36 airClient TOTAL Security - Open System/Shared Key Conf iguration Table 2-3 Security Settings for Open Sy stem/Shared Key Page Items Descriptions Authentication Type Choose between open system and shared key authent ication modes Open System : Open Syst em i[...]

  • Seite 51

    Page 51 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 1. Click on Radio | Security from the main menu. A screen as shown in the fig ure below will appear for the WPA-PSK settings. 2. Select the Authentication Type as WPA-PSK fro m the dr op down menu. 3. Enter the Key E n try Met hod as AS CII or HEX. 4. Enter the WPA-Sha[...]

  • Seite 52

    Page 52 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 3. Wireless Settings and Bandw id th Controller 3.1. Wireless Settings The Wi reles s Setti ngs can be acces sed fr om the Radio | Wireless Settings in the navigation menu bar. Figure 3-1 airClient TOTAL Wireless Settings The following table summarizes the information [...]

  • Seite 53

    Page 53 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Page Items Desc riptions 03 only) For Router/NAT modes or Client Bridge Mo de (3415-03 only), this MAC addre ss needs to be set to 00:00:00:00:00:00 Wire le ss M ode This is the radio operating mode of the client. This can be set to the wireless 802.11b or 802.11g. Ant[...]

  • Seite 54

    Page 54 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 3.2. Bandwidth Control Using the Bandwidth Controller, the user can limit the wireless link bandwidth speed. The maximum allowable bandwidth is up to 512Kbps in sB3415-01, 1 Mbps in 3415-02 and 3 Mbps in 3415-03. This is subject to the available upstream bandwidth, sig[...]

  • Seite 55

    Page 55 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Figure 3-3 airClient TOTAL Bandwidth Control (sB3415-03)[...]

  • Seite 56

    Page 56 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 3.2.2. Ethernet Bandwidth Control (sB3415-03 only) Note: This section is only applicable for sB3415-03. sB3415-03 allows you to limit the amount of bandw idth for each device connected on the Ethernet side, to allow for proper sharing of the bandwidth. The bandwidth on[...]

  • Seite 57

    Page 57 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Follow the steps be low to control the Ban dwidth parameters on the Ethernet side, b ased on MAC address: 1. From the navigation menu bar, click on Networking | Bandw idth Control . 2. In the E thernet Bandwidth Control settings. click on t he Enable Bandwidth BWC butt[...]

  • Seite 58

    Page 58 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 1. Click on Netw orking | Bandwidth Control from the m enu bar to acces s the Band width Contro l page, as shown below for MAC based Ethernet BWC in Fig 3-6. 2. In the Ethernet Bandwidth C ontrol Settings, click on the Edit co rresponding to the row you w ish to edit. [...]

  • Seite 59

    Page 59 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 4. T raffic S t atistics Wireless Statistic s can b e displ ayed by clicking on Networking | Wireless Stat istics from the navigation menu. The following figure shows the statistics page. Figure 4-1 a irClient TOTAL Wirele ss Statistics The following table summarizes t[...]

  • Seite 60

    Page 60 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 5. T ools In this section, you w ill find relevant in formation for changing the o perating mode of the d evice, saving the configuration, restoring to factory defaults and upgrading the firmware. 5.1. System Configuration The System Configuration page a llows the user[...]

  • Seite 61

    Page 61 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide The following table summarizes the inform ation for the System Configuration page. Table 5-1 System Configuration Page Items 5.2. SNTP Setting The device time comes fro m the network time informatio n source. The device needs access to a ne twork timer (NTP time server[...]

  • Seite 62

    Page 62 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 5.3. Site Survey From the navigation menu bar, click on Tools | Site Survey to access the Site S urvey page. A screen, similar to the one below, would show all the standards-based wireless devices operating in the area. Figure 5-3 airClient TOTAL Site Survey The follow[...]

  • Seite 63

    Page 63 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 5.4. System Admin This menu option allows the user to change the User Name and/or password to access the unit. Refer to chapter 2.2 to change the user name and/or administrator p assword. The default user name is adm in istr at or and the default password is smartBridg[...]

  • Seite 64

    Page 64 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 5.6. SNMP Configuration The user can enable or disable the SNMP configuration using this tool. Follow the steps below to change the SN MP settings: 1. Click on Tools | SNMP Co nfiguration to access the SNMP Con figuration page, as shown below in Fig 5-5. 2. Enable or D[...]

  • Seite 65

    Page 65 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 5.7. Backup/Restore Settings The Backup/Restore page backs up good configuration settings of the system . This can be used to restore the unit in case of any undesired circumstances. Follow the step s below to change the Backup /Restore settings: 1. From the navigation[...]

  • Seite 66

    Page 66 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 5.8. Firmware Upgrade The airClient TOTAL unit firmware can be upgraded from the web management interface. The latest firmware for airClient TOTAL is a vailable for download from the smartBridges support website at http://www.smartbridges.com/support/aCT241.asp . Follo[...]

  • Seite 67

    Page 67 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Figure 5-8 airClient TOTAL Firmware Upgrade Figure 5-9 airClient TOTAL Successful Firmware Upgrade message[...]

  • Seite 68

    Page 68 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 5.9. Product License Key This feature is used to enhance/upgrade the default bandwidth on th e airClient TOTAL units, and to convert the models between sB3415-01, sB3415-02 and sB3415-03. By default, the 3415-01 allow s a maximum bandwidth of 512 kbps, 3415-02 allows a[...]

  • Seite 69

    Page 69 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 5.10. Link Budget Planning Link Budget Planning is a very useful tool for link budget estimation. A GPS Calculator is provided in the Link Budget Planning Calculator page to calculate the distance between an airClient TOTAL unit and an access poin t. To calculate the d[...]

  • Seite 70

    Page 70 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 5. Click the Compute Link B udget button to calculate the link budget information. 6. The link budget information will be displayed as shown below in Fig 5-12 . The link budget information include s the EIRP, Free Space Loss and Theoretical RSSI. The Receive Sensitivit[...]

  • Seite 71

    Page 71 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 5.11. System Log sB3415 allows the System logs to be created locally or remotely on the PC conne cted to the unit. Local logging is persistent across resets of the 3415-01/02/03 units. To configure the System Log on the 3415 device, follow the steps below : 1. From the[...]

  • Seite 72

    Page 72 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide To refresh or cle ar the Syslo g entries logg ed loca lly on the de vice, follow the ste ps below : 1. Select Tools | Syst em Log from the Na vigation menu bar. The System Log web page will appe ar as shown above in Fig 5-13. 2. At the bottom of this page, th ere are t[...]

  • Seite 73

    Page 73 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide 5.12. Reboot The device wo uld need to be rebooted in case any changes are to be made to the syste m, or a new firmware is download ed. Click o n Tools | Reboot to r eboot the unit. A figure showing the countd own to 0 will appear as shown below during the Reboot proce[...]

  • Seite 74

    Page 74 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide Appendix A – Some usef ul terms and definitions Acronyms and Abbrev iations MAC Media Access Control RSSI Receive Signal Sensitivity Indication SSID Service Set Identifier DHCP Dynamic Host Configuration Protocol ACL Access Control List SNMP Simple Network Management[...]

  • Seite 75

    Page 75 of 75 intelligent wireless platform airCli ent™ TOTAL 3415 User G uide COFDM COFDM involves modulating the data onto a large number of carriers using the OFDM te chnique. The Key features which makes it w ork, in a manner is so w ell suited to terrestrial channels, includes: • Orthogonality (the “O” of C OFDM); • The addition of G[...]