Sears 831.159412 Bedienungsanleitung

Model No. 831.159412 Serial No. Write the serial number in the space above for reference. Serial Number Decal F- x EE R C i _%_ E_ EQUIPMENT HELPLINE! 1-800-735-5879 CAUTION! Read all precautions and Instructions in this user's man- ual before using this equip- ment. Save this user's manual for future reference. PATENT PENDING USER'S[...]

TABLE OF CONTENTS IMPORTANT PRECAUTIONS ..................................................................... 2 BEFORE YOU BEGIN ........................................................................... 3 ASSEMBLY .................................................................................... 4 TROUBLE-SHOOTING AND MAINTENANCE ..............[...]

BEFORE YOU BEGIN Thank you for selecting the PROFORtvP BODYLIFT Body Weight Resistance System. The compact BODYLIFT features an impressive array of weight sta- tions designed to develop every major muscle group of the body. Whether your goal is a shapely figure, dramatic muscle size and strength, or a healthier car- diovascular system, the BODYLIFT[...]

ASSEMBLY Before beginning assembly, carefully read the following Information end Instructions: • Assembly requires two people. • Due to the size of the BODYLIFT, it should be assembled in the location where it will be used. • Place all parts of the BODYLIFT in a cleared area and remove the packing materials; do not dis- pose of the packing ma[...]

3. 3 . . Attach the Footrest (35) to the Front Upright (7) with two 3/8" x 2 3/4" Bolts (85), two 3/8" Flat Washers (53), and two 3/8" Nylon Locknuts (33) as shown. Remove the 3/8" x I 112" Carriage Bolt (80) and the 3/8" Nylon Jam Nut (41) from the indicated brackets on the Front Upright (7). Remove the loop of C[...]

. 7o Slide a Weld Cover (63) onto each of the indicat- ed axles on the Front and Rear Uprights (7, 2). The Weld Covers must be tumed so the open sides are facing the Uprights. Lubricate the axles. Slide a Short Riser (4) onto the axles, The Short Riser must be turned as shown. Hold a 3/4" J=tetainer (57) and a 3/4" Retainer Cap (59) again[...]

. Carefully cut the wire tie attached to the Cable (25). Wrap the loop of Cable from steps 4 and 5 around the 3 1/2" Pulley (27) as shown. Hold the Pulley and the Pulley Covers (88) between the indicated holes in the Selector Plate (19). Make sure that the Pulley Covers are turned so the small rims are inside the loop of Cable as shown. See as[...]

10. Pull the Moment Arm(10) forward. Hold the lower and of the Left Press Arm (52) in the upper end of the Moment Arm. The Left Press Arm must be turned so the Handle (12) is on the side shown. Attach the Left Press Arm with two 3/8" x 2 1/2" Bolts (44) and two 3/8" Nylon Locknuts (33). The Bolts must be Inserted from the side shown,[...]

14. Insert one Pad Tube (13) into the Seat Frame (8). 14 Insert the other Pad Tube into the LegLever (9). Slide two 6" Pads (24) onto each Pad Tube (13). 15. Pivot the Link Tube (16) on the Left Arm (5) onto the end of the Link Tube Axle (17). Attach the Link Tube to the Link Tube Axle with a 114" x 1 1/4" Bolt (49) and a 1/4" A[...]

TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the BODYLIFT. Replace any worn parts immediately. The BODYLIFT can be cleaned using a damp cloth and mild non-abrasive detergent, Do not use solvents, HOW TO TIGHTEN THE CABLE Woven cable, the type used on the BODYLIFT, can stretch slightly when it is first used. If th[...]

USING THE BODYLIFT The instructions below describe how each part of the BODYLIFT can be adjusted. Refer to the EXERCISE GUIDE accompanying this user's manual for exercise guidelines, and to see how the BODYLIFT should be set up for each exercise. IMPORTANT: When attaching the lat bar or nylon strap, make sure that the attachments are in the co[...]

[...]

This chart is provided to help you identify the small parts used in assembly. Remove this chart from the user's manual before beginning assembly.[...]

PART IDENTIFICATION CHARTmModel No. 831.159412 This chart is provided to help you identify the small parts used in assembly. The number in parenthesis below each part refers to the key number of the part. The second number refers to the quantity needed for assembly. Note: Some parts may have been pre-assembled for shipping purposes; if you cannot f[...]

1/4" x 3/4" Sorew (47)-2 1/4" x 1 1/4" Bolt (49)-3 3/8" x 2" Bolt (87)-1 1/4" x 2 1/2" Carriage Bolt (46)-1 5/16" x 2 3/4" Bolt (78)-1 1/4" x 2 1/2" Screw (32)-1 3/8" x 2 1/2" Carriage Bolt (70)-4 3/8" x 2 1/2" Bolt (44)-4 3/8" x 2 3/4" Bolt (85)--3 1/4" [...]

EXPLODED DRAWING--Model No. 831.159412 71 79 14 46 33 24 21 67 69 .78 13 24 33 53 _. 27, 42 66 12 18 6O 33 9O 63 52 i 72 37 .-'" 27 5O 41 53 75 4O 63 85 4 57 59 19 59 57 81 RO195B[...]

PART LIST--Model No. 831.159412 Key Part Key Part No. No. Qty. Description No. No. Qty. Description 1 120574 1 Base 54 013485 1 2 120575 1 Rear Upright 55 121576 3 3 121466 2 Long Riser 56 102603 2 4 121467 2 Short Riser 57 101578 8 5 121468 1 Left Buttedly Arm 58 120810 16 6 121469 1 Right Butterfly Arm 59 120788 8 7 120580 1 Front Upright 60 1207[...]

HOW TO ORDER REPLACEMENT PARTS Each BODYLIFT has its own MODEL NUMBER. Always mention this MODEL NUMBER when requesting service or repair parts for your BODYLIFT. All parts listed herein can be ordered through SEARS, ROEBUCK AND CO. SERVICE CENTERS and most SEARS RETAIL STORES. If parts you need are not stocked locally, your order will be transmitt[...]