Roland RT-10K Bedienungsanleitung

04232178 ’06-4-2N * 04232178 - 02 * Owner’s Manual Thank you, and congratulations on your choice of the Roland RT-10 series. 201a Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (p. 2; p. 3). These sections provide important information concerning the proper operation of the un[...]

2 USING THE UNIT SAFELY 001 • Before using this unit, make sure to read the instructions below, and the Owner’s Manual. .................................................................................................. 002a • Do not open or perform any internal modifi- cations on the unit. .....................................................[...]

3 IMPORTANT NOTES 291a In addition to the items listed under “USING THE UNIT SAFELY” on page 2, please read and observe the following: Placement 354a • Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes. Excessive heat can def[...]

4 Before You Start • Drum trigger • Connection cable • Owner’s Manual (this manual) • Two hoop guards (RT-10K only) • Works perfectly with Roland V-Drums Modules • High-Accuracy Sensor for Perfect Triggering • Dual Trigger for Head & Rim (only RT-10S Snare Trigger) • Mounts Easily and Quickly on Hoop • Adjustable-Sensor Syst[...]

5 Before You Start A drum trigger uses a built-in sensor to sense the timing and velocity (force) of how the drum is played. Then these trigger signals and transmitted to the sound module. The RT-10K Kick Trigger and RT-10T tom trigger support head triggering. The RT-10S Snare Trigger supports separate head/rim dual triggering. 1. Mount the drum tr[...]

6 Mounting The Drum Trigger • Set up your drums, making sure that any trigger-mounted drum is NOT in contact with another drum or stand. Vibrations transmitted from such direct contact can cause unwanted triggering. • Make sure the snare drum is secure in its stand. • Muffling (muting) of the drums can help reduce excess vibrations of the dru[...]

7 Mounting The Drum Trigger fig.RT-10K-toritsuke 1. Attach the included hoop guards (2) to the inner and outer sides of the kick drum hoop. • Attach the hoop guards at one of the positions indicated in the figure. We suggest these positions in order to keep the trigger as far away from the snare drum or tom toms as possible. • Make sure the hoo[...]

8 Mounting The Drum Trigger Set the sensor bolt so that the sensor compresses approximately 2–3 mm when pressed against the head. * The position of the secured sensor and the amount of this compression play an important role in the performance of the trigger. * Make sure that the sensor constantly remains in contact with the head, even when playi[...]

9 Setting Trigger Parameters in a Percussion Sound Module Correct trigger type and parameter settings provide accurate triggering. We have included an extensive list of percussion sound modules with their respective parameter settings. Please refer to the charts beginning on page 14. Unlike standard electronic drum pads, mesh or rubber, acoustic dr[...]

10 Setting Trigger Parameters in a Percussion Sound Module retriggering, it then becomes easy for sounds to be omitted when the drums played fast (roll etc.). * Muting the drum can work to suppress disruptions in the trigger waveform. Crosstalk is a problem in which the vibrations and sounds from a drum when it is struck ends up triggering other dr[...]

11 Troubleshooting Normally, you should not have any problems if you have read this manual carefully, followed the instructions and have carefully taken into consideration the multiple variables regarding using drum triggers; type of drum, head, muffling, playing style, acoustic environment etc. • Check all connections, and make sure the trigger [...]

12 Troubleshooting • Is the volume too loud of nearby monitor speakers? • If in a band situation, is the bass amp too close or too loud? • Adjust the “Threshold” value. (p. 9) Separate triggering from the rim is only possible when using the RT-10S snare trigger. • Make sure the cable is Stereo. • Verify that the trigger input you are [...]

13 Specifications RT-10K (Kick Trigger) Trigger: 1 (Head) Connector: Trigger Output Jack (1/4 inch Phone Type) Dimensions: approx. 40 (W) x 110 (D) x 70 (H) mm approx. 1-5/8 (W) x 4-3/8 (D) x 2- 13/16 (H) inches Weight: 90 g 4 oz Accessories: Connection Cable, Hoop Guard, Owner’s Manual Guide for Installation: Rim Height: 30 to 36 mm 1-3/16 to 1-[...]

14 Percussion Sound Module Parameter Settings Following you will find specific parameter settings for the indicated percussion sound modules. These are VERY important. If needed, please refer to the Owner’s Manual of your module. * The trigger parameters should be adjusted as necessary to match the actual state of your configuration, and the envi[...]

15 Percussion Sound Module Parameter Settings RT-10S Snare Trigger Dual Trigger Compatible Inputs SNARE RT-10S Snare Trigger Dual Trigger Compatible Inputs 2 (SNARE) (*) When you connect the RT-10S to the trigger input 2 (SNARE), make the settings as shown below. 2 HEAD: “Snr” 2 RIM: “riM” TD-3 (Percussion Sound Module) Parameter RT-10K Kic[...]

16 Percussion Sound Module Parameter Settings RT-10S Snare Trigger Dual Trigger Compatible Inputs 1, 2 RT-10S Snare Trigger Dual Trigger Compatible Inputs TRIG IN SPD-20 (Total Percussion Pad) Parameter RT-10K Kick Trigger RT-10S Snare Trigger RT-10T Tom Trigger TRIG SENS 10 10 10 TRIG THRESHOLD 8 7 7 TRIG TYPE KiK 120 toM TRIG CURVE 0 0 0 Advanced[...]

RT-10KST_e.fm 17 ページ ２００６年３月３０日　木曜日　午後１時５５分[...]

As of April 1, 2006 (ROLAND) Information When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below. EGYPT Al Fanny Trading Office 9, EBN Hagar A1 Askalany Street, ARD E1 Golf, Heliopolis, Cairo 11341, EGYPT TEL: 20-2-417-1828 REUNION Maison FO - YAM Marcel 25 Rue Jules Herm[...]