Renesas SH7046 Series Bedienungsanleitung

2004.1.29 SH7046 Group FP-80Q User System Interfa ce Board HS7046ECH61H User’s Manual Renesas M icrocomput er Developm ent Enviro nment System SuperH TM Family /SH7046 S eries Rev.4. 00[...]

Cautions Keep safety first in your circ uit designs! 1. Renesas Technology Corp. put s the maximum e ffort int o making semi conductor pr oducts better and more reliable, but the re is always the possibility that trouble may occur with them. Trouble with semi conductors may l ead to personal i njury, fire or property dama ge. Remember to give due c[...]

I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this u ser system interface board. • KEEP the user's manual handy for future reference. Do not atte m pt to use the user system interface bo ard until you fully under stand its mec ha ni s m. User Syst em Interface Board: Throughout thi s document, the ter m &qu[...]

II LIMITED WARRANTY Renesas warrants its user system interface boards to be manufa ctured in accordance with published specifications and free from defects in material and/or workmanship. Renesas will re pair or replace any user system interfac e boards determined to be defe ctive in material and/or workmanship. User s ystem interface bo ards are w[...]

III State Law: Some states do not allo w the exclusion or limitatio n of implied warranties or liabilit y for incidental o r consequential d amages, so t he ab o ve limitation or excl usion ma y not appl y to you. This warr ant y give s yo u spec if ic lega l rig hts, and you ma y have ot her rig hts wh ic h may va ry fro m state to state. The Warr[...]

IV SAFETY PAGE READ FIRST • READ this user's manual before using this u ser system interface board. • KEEP the user's manual handy for future reference. Do not atte m pt to use the user system interface bo ard until you fully under stand its mec ha ni s m. DEFINITION OF SI GNAL WORDS This is the safet y alert symbol. It is used to ale[...]

V W ARNING Observe the pr ecautions listed below. Failure to do so will result in a FIRE HA ZARD and will damag e the user system and the emula tor product or will result in PERSONAL INJURY. Th e USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product b y yourself for e lectric shock pr evention and qualit y assurance. 2. Always[...]

i Preface The HS7046ECH61H is a u ser sys tem in terface board that conn ects a user sy stem for the S H7046 FP-80Q packag e to the SH7046 E6000H em ul ator (HS7046EPH60H).[...]

ii Contents Section 1 Configuration ..................................................................................... 1 Section 2 Connection Procedures ...................................................................... 3 2.1 Connectin g User System Interf ace Board to User System ................................................ 3 2.1. 1 Ins[...]

1 Section 1 Configuration Figure 1 and table 1 sh ow th e configu ration and compon ents of the u ser system interface board f or the FP-80Q packag e. Please make sure y ou hav e all of these com ponents w hen un packing. Socket cover Screws (M2.0 x 8 mm) with flat washers EV-chip board Board User system Spacer IC socket Screws (M2.0 x 12 mm) with [...]

2 CAUTION Use an IC149-080- 017-B5 socket (manuf actured by YAMAICH I ELECTRONICS Co., Ltd.) for the FP-80Q package IC socket on the user syst em. Table 1 HS7046ECH61H Compon ents No. Component Quantity Remarks 1 Board 1 With two spacers (2.6MP x 6 m m) 2 IC socket 1 For the FP-80Q package (to be mounted on the user system) 3 Socket cover 1 For the[...]

3 Section 2 Connection Procedures 2.1 Connectin g User System Interface Board to User S ystem W ARNING Always switch OFF the user syst em and the emulator product before the USER SYSTEM INTERFACE BOARD is connected to or removed from any part . Before connecting, make sure that pin 1 on bot h sides are correctly aligned. Failure to do so will resul[...]

4 2.1.2 Installing Cable Hea d CAUTION Check the location of pin 1 before inserting. Align pin 1 on the IC sock et for an FP-80Q packag e on the user sy stem with pin 1 on the us er system interface board, an d insert the user sy stem interface board into th e IC socket on the u ser system , as shown in figure 2. 2.1.3 Fas tening Cable Head CAUTION[...]

5 Screws (M2.0 x 12 mm) with flat washers Pin 1 Board IC socket (IC 149-080-017-B5 manufactured by YAMAICHI ELECTRONICS Co., Ltd.) User system Figure 2 Connecting User System Interface Board to User System[...]

6 2.2 Connecting User System Interface Board to EV-Chip Board W ARNING Observe the precautions listed below. Failure t o do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user syst em and the emulator product before t[...]

7 Connector No. UCN1 UCN1 UCN2 UCN2 Board EV-Chip Board Connector No. Board Connector No. EV-chip board Spacer User system Figure 3 Connecting User System Interface Board to EV-Chip Board[...]

8 2.3 Recom me nded Dim ensions for User System M ount Pad ( Footprint) Figure 4 show s the recom m ended dimens ions for the m ount pad (f ootprint) for the us er system w ith an IC socket f or an FP-80Q packag e (IC149-080- 017-B5: m anuf actured by YAMAIC HI ELECTRONICS C o., Ltd.). Note that the dim ensions in figu re 4 are somew hat diff erent[...]

9 2.4 Dim ensions for EV-Chip Boar d and User Syste m Inter face Board The dimens ions for the EV- chip board and the u ser system interface board are show n in figure 5. 140.0 19.5 31.0 33.5 16.0 100.0 116.0 92.0 69.0 29.5 5.0 34.5 Unit: mm Tolerance: ±0.5 mm EV-chip board User system interface board Spacer Figure 5 Dim ensions for EV-Chip Board [...]

10 2.5 Resultin g Dimensions after Con necting User System Interf ace Board The resulting dim ensions, af ter connecting th e user system interface board to th e user system , are shown in figure 6. Unit: mm Tolerance: ±1.0 mm User system EV-chip board IC socket (IC149-080-017-B5 manufactured by YAMAICHI ELECTRONICS Co., Ltd.) 31.0 29.5 29.5 31.0 [...]

11 Section 3 Installing the MCU to the User System CAUTION 1. Check the locat ion of pin 1 before inserting. 2. Use a Philips-type screwdriver whose head matches the screw head. 3. The tightening torque must be 0.294 N•m or less. If the applied torque cannot be accurately measured, stop tightening when th e force required to turn t he screw becom[...]

12 MCU (SH7046) Screws (M2.0 x 8 mm) with flat washers Socket cover Pin 1 User system IC socket (IC 149-080-017-B5 manufactured by YAMAICHI ELECTRONICS Co., Ltd.) Figure 7 Installing M CU to User System[...]

13 Section 4 Verifying Operation 1. Turn on the em ulator accordin g to the procedures described in the SH7046 E6000H Em ulator User's Manual (HS 7046EPH60HE). 2. Verify th e user sy stem interf ace cable connections by checking the pin states w ith the extended monitor an d checking the bus states w ith the FIL L comm and (em ulator com mand)[...]

14  To use the crystal oscillator mounted on the EV-chip board Install a crystal oscillator into the crys tal oscillator terminals on the EV-chip board. Evaluation chip board Crystal oscillator terminals Crystal oscillator Enlarged view X1 X2 Figure 9 Installing the Clock Oscillator[...]

15 Section 5 Notice 1. Before connectin g any parts or cables, make su re that pin 1 on the both sides are correctly aligned. 2. Do not apply excessive force to the u ser system interface board w hile it is con nected to the user system . 3. The dimen sions of th e recomm ended mou nt pad for the IC sock et for this user sy stem interface board are[...]

SH7046 Group FP-80Q User System Interface Board HS7046ECH61H User's Manual Publication Date: Rev.4.00, January 29, 2004 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Technical Documentation & Information Department Renesas Kodaira Semiconductor Co., Ltd.  2004 Renesas Technology Corp. All rights reserve[...]

SH7046 Group F P-80Q User Sy stem Inte rface B oard HS7046E C H61H U ser’ s Manual REJ10B0040-0400H[...]