Renesas H8SX/1648 Bedienungsanleitung

H8SX/1648 Group E6 000H PLQP014 4KA-A User System Interface Board HS1648ECH61H User’s Manual Renesas M icrocomput er Developm ent Environm ent System H8SX Family / H8SX/ 1600 Ser ies HS1648EC H61HE REJ10J1869-0200 Revision Date: A pr. 18, 2008 Rev.2.00[...]

[...]

1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any[...]

[...]

I IMPORTANT INFORMATION READ FIRST • READ this user's ma nual befo re using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to u se the user s ystem in terface board until y ou fully understand it s mechanism. User Syst em Interf ace Board : Throughout this document, the term "[...]

II LIMITED WA RRANTY Renesas warrants its user syst em interfa ce boards to be manufactu red in accordance with published specific ations and free from defects in material and/or workmanship. Renesas will repair or replace a ny user system interfac e boards determined to be defective in material and/or workmanship. Us er system interf ace boards ar[...]

III State Law : Some states do not allo w the exclusion or limitation of implied warran ties or liability for incidental or c onsequential damages, s o the above limi tation or excl usion may not apply t o you. This warrant y gives you s pecifi c legal rights , and yo u may have ot her rights which ma y vary fr om state to state. The Warranty is Vo[...]

IV SAFETY PAGE READ FIRST • READ this user's ma nual befo re using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to use the user sys tem in terface boa rd until you fully understand its mechanism. DEFINITION OF SI GNAL WORDS This is the safety ale rt symbo l. It is used to alert [...]

V W ARNING Observe the pr ecautions list ed below. Fai lure to do so will result in a FIRE H AZARD and will damage the us er system and the emul ator product or will r esult in PERSONAL INJURY. The USER PROGRA M will be LOST. 1. Do not repair or remodel the emul ator product by yourself for e lectric shock pre vention and qualit y assurance. 2. Alw[...]

VI[...]

i Preface The HS1648ECH61H is a us er system interface board that connects a user s ystem for the H8SX/1648 PL QP0144KA-A (former package: F P-144L) package to the H8S X/1650 E6000H emulator (HS1650EP H60H). Emulati on of the H8SX/1648 group i s only poss ible when thi s user system interface board is c onnected to the HS1650EPH 60H.[...]

ii Content Section 1 Configuration ..................................................................................... 1 Section 2 Connection Procedures ...................................................................... 3 2.1 Connecting the User System Interface B oard to the User System .................................... 3 2.1.1 Installing[...]

1 Section 1 Configuration Figure 1 and table 1 show the conf iguration and component s of the user sys tem interface board for the PLQP0144KA-A package. Please make sure you have al l of these components aft er you have unpacked the box. Evaluation-chip board Spacer User system interface board User system IC socket Screws (M2 × 10 mm) (for fasteni[...]

2 CAUTION Use an NQPACK144SD -ND socket ( manufactured by Tokyo Eletech Corporation) as the PLQP0144KA- A-packaged IC socket on the user syst em. Table 1 HS1648ECH61H Com ponents No. Component Quantity Remarks 1 User system interface board 1 2 IC socket 1 For the PLQP0144KA-A package (to be mounted on the user system) 3 Socket cover 1 For installin[...]

3 Section 2 Connection Procedures 2.1 Connecting the User Sy stem Interface Board to the User System W ARNING Always switch OFF the user syst em and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed. Before connecting t he two, make sure that pin 1 on both sides are correct ly aligned. Failure to do so will result [...]

4 To connect the b oard to the u ser system, follow the in structions below. 2.1.1 Installing the IC So cket After checking the locat ion of pin 1 on the IC s ocket fasten it to the user s ystem before soldering. CAUTION After confirming the locat ion of pin 1 on the IC socket, apply epoxy resin adhesive to the end of the four projections at the bo[...]

5 2.1.2 Soldering the IC Socket After fasteni ng, solder the IC socket for a PLQP0144KA-A package t o the user system. CAUTION Be sure to completely solder the leads so t hat the solder gently covers the leads and forms solder fillets. (Use slightly more solder than with the MCU.) 2.1.3 Inserting the IC Socket Connector CAUTION Check the location o[...]

6 2.1.4 Fastening th e IC Socket Connector CAUTION 1. Use the screwdriver provided fo r tightening screws. 2. The tightening torque must be 0.054 N•m or less. If the applied torque ca nnot be accurately measured, stop tightening when th e force required to tu rn the screw becomes significantly greater th an that needed when f irst tightening. If [...]

7 User system interface board User system Pin 1 Screws (M2 × 10 mm) (for fastenin g the board) IC socket (NQPACK144SD-ND manufactured by Tokyo Eletech Corporation) Figure 3 Connecting the User System In terface B oard to the User System[...]

8 2.2 Exchanging the Sp acers of the Evaluation-Chi p Board After connecting the user system in terface board to the us er system, be careful not to apply load to the user system. Exchange the spacers (2.6MP × 10 mm) of the evaluation-chip board with the spacers (2.6MP × 25 mm) provided with the user system interface board and adjust the height. [...]

9 2.3 Connecting the User Syst em Interface Board to the Evaluation-Chip Board W ARNING Observe the precautions listed below. Failure t o do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user syst em and the emulator[...]

10 Connector No. UCN1 UCN1 UCN2 UCN2 User system interface board Evaluation-Chip Board Connector No. Board Connector No. Evaluation-chip board Figure 5 Connecting the Us er System In terface Board to the Evaluati on-Chip Board[...]

11 2.4 Recommended Dimensions for the User System Mounting Pad (Footprint) Figure 6 shows the recommended dimensi ons for the mounting pad (foot print) for the us er system with the IC s ocket for a PLQP0144KA -A package (NQPAC K144SD-ND: manufactured by Tokyo Eletech Corporati on). Note that the dimens ions in figure 6 are s omewhat different from[...]

12 2.5 Dimensions of the Evaluation-Chip Board and the User System Interface Board The dimensions of the evaluati on-chip board and the user s yst em interface board are shown in figure 7. Unit: mm Tolerance: ± 0.5 mm 140.0 Evaluation-chip board User system interface board 118.5 100.0 84.5 78.5 34.5 Figure 7 Dime nsions of the Evaluati on-Chip B o[...]

13 2.6 Dimensions after Connecting th e User System Interface Board The dimensions of the ass embly after the user system interface board has been connected to the user syst em are shown in figure 8. Unit: mm Tolerance: ±1.0 mm 32.9 13.3 54.9 User system Evaluation-chip board IC socket (NQPACK144SD-ND manufactured by Tokyo Eletech Corporation) 56.[...]

14 2.7 Using the Emulator with out Connecting User System W ARNING Always switch OFF the user syst em and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed. Before connecting t he two, make sure that pin 1 on both sides are correct ly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user s[...]

15 SW1 USER ON USER OFF Figure 9 SW1 Jumper Socket Spacer (2.6MQ x 13 mm) Figure 10 Attaching Spacers[...]

16 Section 3 Installing the MCU to the User System CAUTION 1. Check the locat ion of pin 1 before inserting. 2. Use the screwdriver provided fo r tightening screws. 3. The tightening torque must be 0.054 N•m or less. If the applied torque ca nnot be accurately measured, stop tightening when th e force required to tu rn the screw becomes significa[...]

17 MCU Pin 1 IC socket (NQPACK144SD-ND manufactured by Tokyo Eletech Corporation) User system Screws (M2 x 6 mm) Socket cover Figure 11 Insta lling MCU to User System[...]

18 Section 4 User System Interface Circuits The following user system interface circuits are required to use the emulator with the user syst em interface board. MCU User system Sub-MCU SN74CB3Q3306A PJ2, PJ3 PK2-PK7 PO16-PO23 PO24-PO31 PD0-PD7 PE0-PE7 PD0-PD7 (PJ0-PJ7) PE0-PE7 (PK0-PK7) SN74CBTL V3257 47 k Ω Vcc PJ0 PJ1 PJ4 PJ5 PJ6 PJ7 PK0 PK1 SN7[...]

19 MCU User system Sub-MCU P30 P31 P34 P35 P36 P37 P20 P21 47 k Ω Vcc P30 P31 P34 P35 P36 P37 P20 P21 TIOCA0 TIOCB0 TIOCA1 TIOCB1 TIOCA2 TIOCB2 TIOCA3 TIOCB3 Figure 13 User System Interface Circuit (2)[...]

20 47 k Ω Vcc PF7 MCU User system SN74CB3Q3306A PF7 PF5 SN74CB3Q3306A PF6 PF6 PF5 Sub-MCU SCK5 RxD5 TxD5 Figure 14 User System Interface Circuit (3)[...]

21 47 k Ω Vcc MCU SN74CB3Q3306A P65 SN74CB3Q3306A P64 P63 SCK6 RxD6 TxD6 Sub-MCU P65 P64 P63 User system Figure 15 User System Interface Circuit (4)[...]

22 47 k Ω Vcc MCU EPM3256A TC ADTRG0 SW2 1 P13 PB6 P13 3 PB6 Sub-MCU User system 47 k Ω Vcc Figure 16 User System Interface Circuit (5)[...]

23 Section 5 Verifying Operation 1. Turn on the emulator according to the pr ocedures described in the H8SX/1650 E6000H Emulator User's Manual (HS1650EPH 60HE). 2. Verify the user system interface cable c onnections by checking the pin s tates with the EXMONITOR_DISPLAY command (emulator command ) and checking the bus states with the MEMORY_FI[...]

24 ⎯ To use the crysta l resonator mounted on the eval uation-chip board Install the cry stal resonator in to the crystal reson ator termin als on the evaluatio n-chip board. Evaluation-chip board Crystal resonator terminals Crystal resonator Enlar g ed view X1 X2 Figure 18 Moun ting the Crys tal Resonator[...]

25 Section 6 Points for Caution 1. Before connecting any parts or cables, make sure that the pi ns at the pin 1 pos ition on bot h sides are correctly aligned. 2. Do not apply excessive force to the user sy stem interface board while it is connected to the user sy stem. 3. The dimensions of the recommended mounting pad for the IC socket for this us[...]

26 Section 7 Restrictions 1. Deep-software standby mode This emulator does not support deep-s oftware standby mode. Note that the emulator switches to the software st andby mode ev en if the register setting to select the deep-s oftware standby mode is made. 2. Sleep-instruction except ion processing This emulator does not support the proces sing o[...]

27 8. A/D converter In the emulator, the evaluation ch ip and the slave chip are used to implement fun ctions of Unit 0 and Units 1 and 2, respect ively, of the A/D convert er. For this reason, w hen the A/D control register (AD CR) has been s et to st art A/D conversi on (with synchronizat ion of units) by an external trigger from t he ADTRG0 pin,[...]

28[...]

H8SX/1648 Group E6000H PLQP0144KA-A User System Interface Board HS1648ECH61H User's Manual Publication Date: Rev.2.00, April 18, 2008 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Customer Suppor t Depar tment Global Strategic Communication Div . Renesas Solutions Cor p. © 2008. Renesas Technology Corp., All [...]

Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan http://www.renesas.com Refer to " http://www.renesas.com/en/network " for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) [...]

[...]

H8SX/1648 Gr oup E6000H PLQP0144KA-A User System Interface Board HS1648ECH6 1H User’s Manual[...]