Proxima ASA Pro AV 9400 Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58

Zur Seite of

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Proxima ASA Pro AV 9400 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Proxima ASA Pro AV 9400, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Proxima ASA Pro AV 9400 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Proxima ASA Pro AV 9400. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Proxima ASA Pro AV 9400 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Proxima ASA Pro AV 9400
- Den Namen des Produzenten und das Produktionsjahr des Geräts Proxima ASA Pro AV 9400
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Proxima ASA Pro AV 9400
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Proxima ASA Pro AV 9400 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Proxima ASA Pro AV 9400 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Proxima ASA finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Proxima ASA Pro AV 9400 zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Proxima ASA Pro AV 9400, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Proxima ASA Pro AV 9400 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    Multimedia Pr ojector Model Pr o A V 9400 Pr o A V 9400L (Without Lens) ■ PRESENT A TIONS ■ WORKING SESSIONS ■ TRAINING ■ MUL TIMEDIA ■ ANIMA TION ■ VIDEO[...]

  • Seite 2

    2 WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This Projector has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature. Intense light source. Do not stare directly into the projection lens [...]

  • Seite 3

    PROJECTOR (FRONT) PROJECTOR (SIDE) WALL 50cm 50cm 50cm 50cm Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the [...]

  • Seite 4

    4 T ABLE OF CONTENTS PAGE PAGE FEA TURES AND DESIGN 5 INTRODUCTION 5 COMPATIBILITY 5 IMAGE RESOLUTION 5 AUTOMATIC MULTISCANNING SYSTEM 5 SCREEN MODE 5 MULTILANGUAGE 5 UNPACKING THE PROJECTOR 5 TRADEMARKS 5 INST ALLA TION 6-9 NAME OF EACH PART OF THE PROJECTOR 6 SETTING-UP THE PROJECTOR 7 MOVING THE PROJECTOR 8 POWER REQUIREMENTS 9 CONNECTING THE PR[...]

  • Seite 5

    The Pro A V 9400 is a multimedia projector that combines powerful and sophisticated f eatures with easy-to-use, intuitiv e controls. Built-in m ultimedia f eatures include audio, a palette of 16.77 million colors and activ e matrix liquid cr ystal displa y (LCD) technology . The projector is ideal for high-perf or mance business , training and imag[...]

  • Seite 6

    6 EXHAUST VENT CAUTION HOT AIR! Air blown from the exhaust vent is hot. Observe the following when handling your projector or choosing a location to install it. ● Keep heat-sensitive objects away from the exhaust port. ● If you set the projector on top of a metallic surface, the surface will become hot because of the hot air exhaust. Be careful[...]

  • Seite 7

    200" 154" 26.9' (8.2 m) 600" 462" 80.7' (24.6 m) 7 40" 77" 115" 154" 231" 308" 462" 600" 100" 150" 200" 300" 400" 760 mm 760 mm 100" SCREEN POSITIONING: R OOM LIGHT ● This projector is basically designed to project on a flat projection surface. ●[...]

  • Seite 8

    8 Use the carry handle when moving the projector. Replace the lens cover and rotate the leveling/elevation feet fully clockwise when moving the projector to prevent damage to the projector. CA UTION IN CARR YING OR TRANSPORTING THE PR OJECT OR ● Do not drop or give a shock to the projector, otherwise damage or malfunction may result. ● When car[...]

  • Seite 9

    9 Your projector uses nominal input voltages of 100-120 VAC or 200-240 VAC. The projector automatically selects the correct input voltage. The projector is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system. Consult your author[...]

  • Seite 10

    10 SIDE OF THE PR OJECT OR (CONNECT THE COMPUTER) COMPUTER INPUT-1 TERMINAL (HDB15) ANALOG Used to connect a computer to the projector. COMPUTER INPUT-1 TERMINAL (MDR20) DIGITAL Used to connect a computer to the projector. COMPUTER INPUT-2 JACKS (BNC TYPE x 5) Used to connect a computer to the projector. MONITOR OUTPUT TERMINAL (HDB15) Used to conn[...]

  • Seite 11

    11 14 17 20 15 18 19 21 22 16 video/y c/cb (b-y) cr (r-y) S-video RL (mono) audio S-video RL (mono) audio S-video RL audio VIDEO IN-1 VIDEO IN-2 MONIT OR OUT video/y c/cb (b-y) cr (r-y) video/y c/cb (b-y) cr (r-y) SIDE OF THE PR OJECT OR (CONNECT THE VIDEO EQUIPMENT) VIDEO INPUT JACKS-1 (BNC TYPE x 3) Used to connect a video source to the projector[...]

  • Seite 12

    12 CONNECTING THE COMPUTER CONNECTING THE PROJECT OR –––––––– ADB –––––––– –––––––– –––––––– –––––––– –––––––– –––––––– GND –––––––– –––––––– –––––––– Serial Port ADB Port 1 2 3 4 5 6 7 8 9 [...]

  • Seite 13

    13 CONNECTING THE PROJECT OR These jacks will contain the audio information of the selected program source being viewed on the screen (Computer 1, Computer 2, Video 1 or Video 2). If you have selected program source Computer 2 the audio signal connected to the Computer 2 audio input jack will be available at the audio monitor output jacks. Connect [...]

  • Seite 14

    14 USB audio R analog RGB in analog RGB out RG B H V L (mono) (mono) control USB R/C jack serial audio audio RL RL control digital in PC IN-1 PC IN-2 PC OUT COMPUTER OUTPUT (HDB15-PIN TYPE) COMPUTER MONITOR CABLE (NOT PROVIDED) COMPUTER OUTPUT (BNC TYPE x 5) SERIAL PORT INPUT AUDIO CABLE (NOT PROVIDED) AUDIO CABLE (NOT PROVIDED) COMPUTER AUDIO INPU[...]

  • Seite 15

    15 CONNECTING THE PROJECT OR USB audio R analog RGB in analog RGB out RG B H V L (mono) (mono) control USB R/C jack serial audio audio RL RL control digital in PC IN-1 PC IN-2 PC OUT COMPUTER MONITOR CABLE (NOT PROVIDED) SERIAL PORT INPUT AUDIO CABLE (NOT PROVIDED) AUDIO CABLE (NOT PROVIDED) COMPUTER AUDIO INPUT 1 CONTROL PORT OUTPUT 1 MOUSE CABLE [...]

  • Seite 16

    16 NOTE: The hook up should be done as per the above illustration. After hook up, turn on the projector, computer, in that order. USB audio R analog RGB in analog RGB out RG B H V L (mono) (mono) control USB R/C jack serial audio audio RL RL control digital in PC IN-1 PC IN-2 PC OUT SERIAL PORT OUTPUT COMPUTER COMPUTER OUTPUT (DB15-PIN TYPE) SERIAL[...]

  • Seite 17

    USB audio R analog RGB in analog RGB out RG B H V L (mono) (mono) control USB R/C jack serial audio audio RL RL control digital in PC IN-1 PC IN-2 PC OUT NO TE: Before using with digital connection, install (Plug in) Graphic Accelerator PC card into PC card slot of the computer and set up the computer following instructions in the Graphic Accelerat[...]

  • Seite 18

    USB audio R analog RGB in analog RGB out RG B H V L (mono) (mono) control USB R/C jack serial audio audio RL RL control digital in PC IN-1 PC IN-2 PC OUT 123456 ON 18 CONNECTING THE PROJECT OR CONTROL PORT OUTPUT 1 or 2 COMPUTER MONITOR CABLE (NOT PROVIDED) COMPUTER OUTPUT (BNC TYPE x 5) BNC CABLE x 5 (NOT PROVIDED) COMPUTER OUTPUT COMPUTER AUDIO O[...]

  • Seite 19

    19 USB audio R analog RGB in analog RGB out RG B H V L (mono) (mono) control USB R/C jack serial audio audio RL RL control digital in PC IN-1 PC IN-2 PC OUT 123456 ON NOTE: The hook up should be done as per the above illustration. After hook up, turn on the projector, computer, in that order. ON 2 34 5 6 1 ON OFF VGA/MAC ADAPTER SW1 ~ SW6 COMPUTER [...]

  • Seite 20

    20 Connect to the video outputs of a VCR, video disc player, DVD player, video camera, satellite TV tuner or other AV equipment. Connect video output from AV equipment to these jacks using the BNC cables. The video input can be selected 3 type of the input. “COMPOSITE VIDEO", "Y/C SEPARATE VIDEO" and COMPONENT VIDEO {Y, Cb (B-Y), C[...]

  • Seite 21

    21 video/y c/cb (b-y) cr (r-y) S-video RL (mono) audio S-video RL (mono) audio S-video RL audio VIDEO IN-1 VIDEO IN-2 MONIT OR OUT video/y c/cb (b-y) cr (r-y) video/y c/cb (b-y) cr (r-y) NOTE: The hook up should be done as per the above illustration. After hook up, turn on the projector, video equipment, in that order. VIDEO EQUIPMENT Video Cassett[...]

  • Seite 22

    22 memu mode auto image normal select volume zoom focus lens shift power 5 6 9 7 12 11 10 13 14 8 15 TOP CONTROLS FRONT INDICATORS FR ONT INDICA T ORS T OP CONTR OLS ready lamp lamp replace warning temp 1 2 3 4 BEFORE OPERA TION CONTR OLS AND INDICA T ORS[...]

  • Seite 23

    23 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 LAMP REPLACEMENT INDICATOR Light is orange when projection lamp is nearing end of service life. TEMPERATURE WARNING INDICATOR Flashes red when internal projector temperature is too high. READY INDICATOR Light is green when projector lamp is ready to be turned on. LAMP POWER INDICATOR Light is dim when the proj[...]

  • Seite 24

    P-TIMER MENU AUT O IMAGE MUTE VOLUME COMPUTER FOCUS ZOOM POWER FREEZE/ NO SHOW LENS SHIFT NORMAL 1 2 3 4 5 6 9 7 12 11 10 13 14 8 VIDEO CURSOR D .ZOOM LASER 15 17 18 16 19 24 FR ONT SIDE OPERA TION OF THE REMO TE CONTROL BEFORE OPERA TION LASER POINTER button LASER POINTER button This remote control emits a laser beam light as the Laser Pointer fro[...]

  • Seite 25

    25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 COMPUTER SELECT BUTTON Used to select computer mode. (Computer 1 or Computer 2 Input) VIDEO SELECT BUTTON Used to select video mode. (Video 1 or Video 2 Input) LAMP POWER ON/OFF BUTTON Used to turn the projection lamp on or off. VOLUME BUTTONS Used to adjust volume. ZOOM BUTTON Used to select power zoom lens a[...]

  • Seite 26

    26 Remote Control Battery Installation Using the Remote Control Unit 16.4' (5 m) 60° 60° 1 Remove the battery compartment lid. 2 Slide the batteries into the compartment. 3 Replace the compartment lid. Note : For correct polarity (+ and - terminal), be sure the battery terminals are in contact with the pins in the compartment. Point the remo[...]

  • Seite 27

    WIRED REMOTE JACK When using the wired remote control, connect the remote cable to this jack. COMPUTER SELECT BUTTON Used to select computer mode. (Computer 1 or Computer 2 Input) VIDEO SELECT BUTTON Used to select video mode. (Video 1 or Video 2 Input) LAMP POWER ON/OFF BUTTON Used to turn projection lamp on or off. VOLUME BUTTONS Used to adjust v[...]

  • Seite 28

    28 60° R/C JACK SERIAL PORT OPEN OPEN Connect a remote control cable to R/C jacks located on the wireless/wired remote control unit and the side of the projector. 60° The remote control unit can be used as wireless or wired remote control. WIRED REMOTE CABLE 1 Remove the battery compartment lid. 2 Slide the batteries into the compartment. 3 Repla[...]

  • Seite 29

    ADJUST ITEM 29 The projector has two types of operation: DIRECT OPERATION and MENU OPERATION. DIRECT OPERATION allows you to operate the projector by using one button without showing the MENU. In MENU OPERATION mode, you display menus where you can adjust the projector's settings. Follow the instruction for each control. DIRECT OPERA TION WIRE[...]

  • Seite 30

    30 BEFORE OPERA TION WIRELESS REMOTE CONTROL COLOR SYSTEM WIRELESS REMOTE CONTROL ADJUST ITEM MODE SELECT WIRELESS REMOTE CONTROL SOUND SOUND VOLUME TREBLE BASS BUILT-IN SP. SOUND MUTE WIRELESS/WIRED REMOTE CONTROL MENU POINT LEFT/RIGHT SELECT POINT UP/DOWN SELECT MENU POINT LEFT/RIGHT SELECT POINT UP/DOWN SELECT MENU POINT (LEFT/RIGHT) SELECT (REA[...]

  • Seite 31

    31 BEFORE OPERA TION WIRELESS REMOTE CONTROL 3. COMPUTER MODE NOTES : 1. The MENU, once activated, will not disappear unless you choose MENU QUIT. If you switch to DIRECT operation by pressing a DIRECT operation button while in MENU mode, the menus will disappear and the MENU operation will end. 2. You can use the REMOTE CONTROL UNIT or the TOP CON[...]

  • Seite 32

    32 Connect the projector to a source (Computer, VCR, Video Camera, Video Disc Player, etc.) using the appropriate terminals on the side of the projector (See "CONNECTING THE PROJECTOR" section on pages 10-21). Connect the projector's AC power cord into a wall outlet and turn the MAIN ON/OFF switch (located on the side of the projecto[...]

  • Seite 33

    33 Press the MODE button on the projector or the COMPUTER and VIDEO button on the remote control unit to select Computer 1, Computer 2, Video 1 or Video 2 Input. The "Computer 1", "Computer 2", "Video 1" or "Video 2" display will appear on the screen for a few seconds. DIRECT OPERA TION B ASIC OPERA TION MODE[...]

  • Seite 34

    34 B ASIC OPERA TION Press the D. ZOOM button on the wireless remote control unit. The "D.zoom" and the magnifying-glass icon is displayed to indicate Digital zoom mode. Digital zoom mode can be adjust the image size or pan the image. To expand the image size, press SELECT (REAR CLICK) button. The image is magnified by degrees (Expand fun[...]

  • Seite 35

    MEMU NORMAL SELECT SELECT BUTTON 35 MENU FREEZE/ NO SHOW NORMAL SELECT D.ZOOM In MENU OPERATION mode, you can adjust the projector. You can use the TOP CONTROL THE PROJECTOR or the REMOTE CONTROL UNIT. You can select a mode from MAIN MENU display among computer 1, computer 2, video 1, video 2. 1. Press the MENU BUTTON and the MAIN MENU DISPLAY dial[...]

  • Seite 36

    36 SOUND ADJUST DISPLAY LANGUAGE SETTING DISPLAY MAIN MENU DISPLAY MAIN MENU DISPLAY You can adjust the sound volume, treble, bass levels and Built-in SP., Sound Mute ON/OFF switch in the MENU display. 1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. 2. Press the POINT LEFT/RIGHT BUTTON(s) to select SOUND and press the SEL[...]

  • Seite 37

    37 VIDEO SOURCE DISPLAY MAIN MENU DISPLAY 1. Connect the video equipment to the PROJECTOR, and turn them on projector first. 2. Set MODE SELECT to "VIDEO MODE". 3. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. 4. Press the POINT LEFT/RIGHT BUTTON(s) to select VIDEO SOURCE and press the SELECT (REAR CLICK) BUTTON.[...]

  • Seite 38

    38 IMAGE ADJUST DISPLAY TABLE OF PICTURE IMAGE ADJUSTMENT COLOUR TINT WHITE BALANCE (R/G/B) CONTRAST BRIGHTNESS SHARPNESS 0 63 0 63 63 63 31 0 63 0 0 0 DECREASES INCREASES DECREASES INCREASES MORE PURPLE MORE GREEN LIGHTER DEEPER DARKER BRIGHTER SOFTER SHARPER MAIN MENU DISPLAY Picture adjustments have been preset at the factory. If you want to cha[...]

  • Seite 39

    39 SCREEN ADJUST DISPLAY MAIN MENU DISPLAY This projector has the Wide function, which enables you to view a wider video image. WIDE function This projector is able to project not only a normal video image (with 4 x 3 aspect ratio), but also a wider video image by compressing 4 x 3 image. This feature enable you to enjoy watching pictures like cine[...]

  • Seite 40

    40 COMPUTER MODE XGA 1 X X X X X X X X X X X COMPUTER SYSTEM DISPLAY CURRENT MODE DISPLAY MAIN MENU DISPLAY This projector is adjustable to different types of computer display signals based on VGA, SVGA, XGA, SXGA or UXGA (See "COMPATIBLE COMPUTER SPECIFICATIONS" on the next page). If you set MODE SELECT to "COMPUTER", the proje[...]

  • Seite 41

    41 ON-SCREEN DISPLAY RESOLUTION H-Freq. (kHz) V-Freq. (Hz) 1024 x 768 60.023 75.03 XGA3 ON-SCREEN DISPLAY RESOLUTION H-Freq. (kHz) V-Freq. (Hz) 70.09 31.47 720 x 400 VGA2 Specifications are subject to change without notice. NOTE: Basically this projector can accept the signal from all computers with the above mentioned V, H-Frequency and less than [...]

  • Seite 42

    42 COMPUTER MODE AUTO IMAGE SETTING DISPLAY MAIN MENU DISPLAY The Auto image function is provided to automatically adjust Fine sync., Total dots and Screen position for most computers. NOTE : This auto image function will be skipped when the incoming signal is digital. 1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. 2. Pr[...]

  • Seite 43

    43 COMPUTER MODE IMAGE ADJUST DISPLAY TABLE OF PICTURE IMAGE ADJUSTMENT WHITE BALANCE (R/G/B) CONTRAST BRIGHTNESS 0 127 63 63 0 63 0 0 TOTAL DOTS FINE SYNC The number of the total dots in one horizontal period. Adjust the number to match your PC image. Adjust the picture as necessary to eliminate flicker from the display. LIGHTER DEEPER DECREASE IN[...]

  • Seite 44

    44 POSITION SETTING DISPLAY MAIN MENU DISPLAY 1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. 2. Press the POINT LEFT/RIGHT BUTTON(s) to select POSITION and press the SELECT (REAR CLICK) BUTTON. Another dialog box POSITION SETTING DISPLAY will appear. 3. Press the POINT DOWN BUTTON and a red arrow will appear. 4. Move the[...]

  • Seite 45

    45 COMPUTER MODE MAIN MENU DISPLAY This projector can automatically detect most display signals from most personal computers currently distributed. However, some computers adopt a special signal format which is different from the standard one and the projector cannot detect it. If this happens, the projector cannot reproduce a proper image. And a f[...]

  • Seite 46

    OK ? Ye s No 630 1056 47 4 46 ITEM T O T AL LINES T O T AL DO TS HORIZONT AL VERTICAL FUNCTION The number of the total vertical lines. Adjust the number to match your PC image. The number of the total dots in one horizontal period. Adjust the number to match your PC image. Adjustment of the horizontal picture position. When the image is not centere[...]

  • Seite 47

    XGA 47 ITEM CLAMP DISPLA Y AREA HORIZ. SCALE FUNCTION Adjustment of the clamp level. When the image has a dark bar, try this adjustment. Expanding or compressing level for the vertical direction. Expanding or compressing level for the horizontal direction. PC ADJUSTMENT DISPLAY 2 MAIN MENU DISPLAY 17. Another dialog box "PC ADJUSTMENT DISPLAY [...]

  • Seite 48

    OK ? Ye s No 630 1056 47 4 Stored Stored 48 MAIN MENU DISPLAY PC ADJUSTMENT DISPLAY MODE FREE The Mode free function is provided to confirm or clear the parameter data produced by PC ADJUST. 1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. 2. Press the POINT LEFT/RIGHT BUTTON(s) to select PC ADJUST and press the SELECT (RE[...]

  • Seite 49

    49 COMPUTER MODE This projector can adjust the image size and pan the image with PICTURE SCREEN ADJUSTMENT. 1. Press MENU BUTTON and MAIN MENU DISPLAY dialog box will appear. 2. Press POINT LEFT/RIGHT BUTTON(s) to select SCREEN and press the SELECT (REAR CLICK) BUTTON. Another dialog box SCREEN ADJUST DISPLAY will appear. 3. Press POINT DOWN BUTTON[...]

  • Seite 50

    50 O THER FUNCTION SETTING This Projector is designed for connecting with USB Port of the computer or peripheral equipment that is to be standard. When this function is in the " " (Mouse) position, you control the pointer of the computer used the projector's wireless remote control unit. When this function is in the " " (Co[...]

  • Seite 51

    51 O THER FUNCTION SETTING SETTING DISPLAY MAIN MENU DISPLAY 1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. 2. Press the POINT LEFT/RIGHT BUTTON(s) to select SETTING and press the SELECT (REAR CLICK) BUTTON. Another dialog box SETTING DISPLAY will appear. 3. Press the POINT DOWN BUTTON and a red arrow will appear. 4. Mov[...]

  • Seite 52

    52 O THER FUNCTION SETTING MAIN MENU DISPLAY SETTING DISPLAY NOTE: Do not reset the LAMP REPLACEMENT MONITOR TIMER, except after the lamp is replaced. 1. Press the MENU BUTTON and the MAIN MENU DISPLAY dialog box will appear. 2. Press the POINT LEFT/RIGHT BUTTON(s) to select SETTING and press the SELECT (REAR CLICK) BUTTON. Another dialog box SETTI[...]

  • Seite 53

    53 The removable air filter prevents dust from accumulating on the surface of the projection lens and projection mirror. Should the air filter become clogged with dust particles, it will reduce the cooling fan's effectiveness and may result in internal heat build up and reduce the life of the projector. To clean the air filter, follow the clea[...]

  • Seite 54

    54 APPENDIX NO TE ON THE LAMP REPLA CEMENT INDICA T OR AND MESSA GE The LAMP REPLACEMENT INDICATOR and the warning message "LAMP REPLACEMENT" indicates the guide of the lamp life. It is unnecessary to replace the lamp immediately if the projector is operating normally with the indicator on. If the LAMP REPLACE INDICATOR is lit (and warnin[...]

  • Seite 55

    55 Before calling your dealer or service station for assistance, follow these steps, to make sure everything is properly connected. 1 . Make sure you have connected the projector to your equipment as described in section "CONNECTING THE PROJECTOR" on pages 14 ~ 21. 2. Check cable connections. Verify that all computer, video and power cord[...]

  • Seite 56

    No sound. 56 Pr oblem: Check Reverse L/R feature. (See "OTHER FUNCTION SETTING" section on pages 50 ~ 51). Picture is L/R Rever sed. Check Reverse T/B feature. (See "OTHER FUNCTION SETTING" section on pages 50 ~ 51). Picture is T/B in ver ted. Check Display feature. (See "OTHER FUNCTION SETTING" section on pages 50 ~ 5[...]

  • Seite 57

    57 TECHNICAL SPECIFICA TIONS Projector T ype Dimensions (W x H x D) Net W eight LCD P anel System Number of Pixels Colour System Scanning Frequency Projection Ima g e Size (Diagonal) Contrast Ratio Horizontal Resolution Projection Lens Motorized Lens Shift Thro w Distance Projection Lamp Projection Mirr or A V Input Jacks Computer A udio Input Jack[...]

  • Seite 58

    Pro xima Cor poration w arrants that the Proxima® Multimedia Projector Model Pro A V 9400 product manuf actured by Pro xima is free from def ects in materials and workmanship under nor mal use during the Warr anty P er iod. The W arranty P eriod commences on the da y of purchase by the end-user . The Warr anty P er iod is two years . The projector[...]