POSIFLEX Business Machines PST - 7700 Bedienungsanleitung

Part 1 FCC Notes: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are d[...]

Part 2 ALERT TO OUR HONORABLE CUSTOMERS: l Please always read thoroughly all the instructions and documents delivered with the produc t before you do anything about it. Don’t take any premature action before you have a full understanding of the consequences. l This product contains inside a Lithium battery and maybe also a sealed type Lead acid b[...]

Part 3 BRIEF INTRODUCTION THE USER’S MANUAL The purpose of this manual is to guide the user in the initial installation and general use of the Posiflex PST7700 series of POS terminals. It does not explain any application software that may be supplied with it. We intend to provide o ur customers with all technology advantages available by evolving[...]

Part 4 THE STANDARD FEATURES CPU: C3 1.0 GHz ; HDD: 20 GB or above; RAM: 128 MB Ethernet Networking: The standard network port works with both 10 Base T and 100 Base T. Programmable Keyboard: In either 112 key matrix or 136 key QWE RTY layout with 8 KB memory. Numerical Keypad: The matrix layout keyboard contains a numerical keypad. 6 Position Key [...]

Part 5 1). PP - 2000 series: Friction type paper feed, 2 stations 9 pin dot matrix impact printer. 2). PP - 5600 series: Friction type paper feed, 9 pin dot matrix impact printer 3). PP - 5700 series: Sprocket type paper feed, 9 pin dot matrix impact pri nter 4). PP - 7000II series: Friction type auto - paper feed, High - speed thermal sensitive li[...]

Part 6 Cashier Display Carton When the order is PST7700 or PST7730, the purchased 9” VGA mono CRT monitor will be shipped in a separate box from the main system un it. When the order is PST7705 or PST7735, the package for the 12.1” color TFT LCD is inserted in a side within the system box. Customer Display Carton This is a separate carton withi[...]

Part 7 INSTALLAT ION GUIDES IMPORTANT Please do not connect the power cord or turn on the main unit until you have fully read the installation guides and followed the instructions!!! TECHNICAL ENHANCEMENTS Applicable technical enhancements in PST 7700 series include RTC bat tery replacement, COM port power supply settings, VGA port power supply set[...]

Part 8 The next step is to pass the monitor cable through a square hole at the back edge of main unit. Open the back door by sliding two back door latches at the bottom of back door toward the center. The back door is easily removable. Remove the cable cover by pulling the latch on the underside of the cable cover (ref. drawing below). Connect the [...]

Part 9 platform of the main unit till it clicks. Screw the pivot back to secure the base of the cashier display on the display platfo rm of the main unit as in drawing below. Remove the cable cover on the display platform (same way as the instructions for CRT model) and connect the VGA connector of the 12.1” TFT LCD through the cable cover openin[...]

Part 10 without the transparent key caps (these are in the accessories box). Also supplied with the keyboard are 4 die cut self - adhesive A4 label sheets that ma y be printed by most conventional means with whatever legends are required by the application. Each type of key top (with transparent key cap) listed in the table at end of BRIEF INTRODUC[...]

Part 11 preferred for a permanent device like a bar code scanner in POS business. To access the internal connection you must remove the keyboard. To do this first unlock the front door lock and then remove the two mounting screws from the underneath of the chassis located just b ehind the front edge of the terminal. Once these screws have been remo[...]

Part 12 CASH DRAWER The P ST7700 installed with power management kit option is able to control most of the common cash drawers available on the market. However, it is recommended that the Posiflex CR - 3100 or CR - 3200 or CR - 4000 or CR - 4100 or CR - 4210 be used since the terminal has be en designed to compliment these cash drawers both mechani[...]

Part 13 USING THE PST SYSTEM BEFORE POWER ON – A Check List It is very important that you check the fol lowing operational points: Ventilation This terminal must NOT be operated in an environment with restricted ventilation. There must be at least 25 mm air clearance around any top or side ventilation holes with a free flow of air around the unit[...]

Part 14 room also provides very good pro tection as long as the ambient temperature remains below 30 ° C and the ventilation of the PST system is free. However, should any accident happen and the sulfuric acid from the battery spills on skin or clothing, wash immediately with water. If the acid com es in contact with eyes, rinse eyes with large am[...]

Part 15 AC power is available when the system is powered off. (b) With a UPS battery fitted together with the power management kit: 1. The standby LED lights steadily to indicate the presence of AC power at system powered off. The system cannot be turned on if the AC power fails. The power LED goes ON and the standby L ED goes OFF when the system i[...]

Part 16 choose for “PM Wake Up Events” in “Power Management Setup” and make the “Ring Power Up Control” enabled for Modem Ring Up or select the “Power Up by Alarm” for Alarm Clock Wake Up. Save the configurati on and exit the CMOS setup program. The Preset Power On Control will then be ready. For LAN wakeup, an operating caller syst[...]

Part 17 LCD MONITOR (for PST7705/PST7735) Mechanical Adjustments The 12.1” LCD color display is integrated on display platform to give the operator the clearest view. The display may be lifted from the horizontal to the upright position and rotated through a total of 90° (left 45 ° max., right 45 ° max.). Please do not to attempt to exceed the[...]

Part 18 There are 4 keys supplied with each keyboard and the lock is so designed that each key may turn the 6 position key switc h to correspondent position range. The keys are named: PRG, REG, Z, GT. The available positions for each key type are listed in the table below: ü = accessible û = not accessible PRG REG Z GT LP ü û û û LCK ü ü ü[...]

Part 19 of the slot, or sliding the card upward from the lower side of t he slot till it reaches the top end as long as the card is a standard one. A non - standard card recorded without complete degaussing prior to recovery may accept only one direction in card reading. The MSR indicator will light up in green when the MSR is re ady to read, blink[...]

Part 20 PRINTER One of the major design features of the PST terminals is the ability to accommodate a very large range of printers. The terminal provides a printer platform where the printer can be mounted (use the Velcro strips in the accessories kit for fixation aid), and also provides a regulated 24 volts DC power line to power the printer. The [...]