POSIFLEX Business Machines KS-6812 Bedienungsanleitung

Part 1 FCC Notes: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are d[...]

Part 2 ALERT TO OUR HONORABLE CUSTOMERS: z Please always read thoroughly all the instructions and documents delivered with the product before you do anything about it. Don’t take any premature action before you have a full understanding of the consequences. z This product contains inside a Lithium battery. Please always follow local environmental[...]

Part 3 INTRODUCTION PRODUCT PICTURES Front View Rear View Side Views Bottom View Inside Base PARTS IDENTIFICATION 1. Main unit 2. Touch panel / LCD panel 3. Power indicator 4. B ase stand 4 6 1 5 3 7 8 2 1 9 18 16 20 17 19 7 12 15 13 13 5 11 10 14[...]

Part 4 5. Optional side mount kit 6. HDD cover CF memory card reader 7. Hinge cover 8. Base back cover 9. Cable exit 10. Power switch 11. LCD brightness up button 12. LCD brightness down button 13. Base back cover hook 14. USB ports on left side 15. Sundries trough for pencils, paper clips etc. 16. Rubber feet with fixing screws 17. Screw holes for[...]

Part 5 5. one VGA port 6. one SATA data port plus one HDD power connector for optional SATA HDD in base eSATA 7. one audio jack for stereo line output 8. one CR port capable of controlling 2 cash drawers max. 9. one 2 pin type DC 12 V power input connector 10. reserved one LPT interface through use of optional special cable in service window k) Bui[...]

Part 6 IN STAL LATION GUIDES CAUTION: Before any installation or cable connection to the set, please always make certain that the system is turned off and the external power source to the set is removed t o prevent electric hazard! Never touch any metal pin in the connectors or circuits to avoid high voltage hazard or electrostatic discharge damage[...]

Part 7 OPENING BASE BACK COVER In order to settle the touch terminal properly in a point of sale system, all the cable connectio ns have to be routed through its base. Therefore, please observe the side view pict ures of the base trunk at the left and release the triangle marked hooks to remove the back cover. CABLE ROUTING IN BASE For cable routin[...]

Part 8 PREPAR I NG THE MAIN UNIT On the back of the main unit, there is a service window facing the base trunk in most of application. It is recommended to tilt the LCD panel to most backward position and rest the surface of LCD panel over a piece of soft clean cloth on a desktop to access the service window. Use a screw driver of adequate length t[...]

Part 9 The KS system will directly control the cash drawer using the cash drawer port (CR) both to operate the opening mechanism and to monitor the drawer open status. Both functions may be accomplished under software control of the COM1 serial port. Use the cable supplied with the cash drawer (Part No. 21863018010) for connection to the CR port in[...]

Part 10 OPERATING SYSTEM RECOVERY For KS-6812 systems with operati ng system in the Compact Flash Card if the system is installed with the CF card reader, once the Compact Flash is damaged for any reason, the thin client may fail to boot. A bootable new Compact Flash Card will be required to have the workstation back to work . Please follow instruc[...]

Part 11 USING THE TOUCH TERMINAL APPLICATION ENVIRONMENT It is very important that you check the following operational guidelines: Ventilation This terminal must NOT be operated in an environment with restricted ventilation. There must be at least 25 mm air clearance around any top or side ventilation holes with a free flow of air around the unit a[...]

Part 12 for within 10 seconds. There must always be at least 10 seconds waiting before switching on again once the system is powered off successfully. Automatic Power On Control The system may also turn on according to some preset conditions such as Modem Ring Up or Alarm Clock Wake Up or LAN Wake Up. To utilize Modem Ring Up or Alarm Clock Wake Up[...]

Part 13 CUSTOMER DISPLA Y Please follow the instructions on the manual that comes along with the customer display when it is installed. DISPLAY ISSUES Main LCD Display For best viewing result please set your display re solution at 1024 x 768 with high color. The system Video Memor y is shared from system memory . The video memory size is default 8 [...]

Part 14 CF MEMORY CARD READER If the CF card reader is installed and the CF card is used for system data storage device, it is recognized by the system as the IDE channe l 1 Master device. The CF memory card reader inside main unit accepts a type II CF memory card. Please note that usual utilities such as FDISK.EXE or FORMAT.COM mus t never be used[...]

Part 15 Posiflex USB Touch Manager A program named “ Posiflex USB Touch Manager” and a right -click sticky button tool in the program group “ Posiflex USB Touch Tools” is installed in the preloaded Windows system with a USB interface touch panel controller. This program can also be obtained by download from the POSIFLEX web site.[...]

Part 16 2 nd Monitor The 2 nd LCD display monitor LM- 3112 can be attached to the rear edge of base bottom of KS-6812 series if no pole display is attached. Refer to the picture at left. Use the 2 attached screws to fix the metal base of the LM to the bottom plate of mini slim base at the circled positions. Connect the VGA cable to go through the c[...]

Part 17[...]

Part 18[...]

Part 19[...]

Part 20 這是甲類的資訊產品， 在居住的環 境中使用時，可能會造成射頻干 擾，在這種情況下，使用者會被要 求採取某些適當的對策。 T31454 本電池如果更換不正確會有爆炸的危險 請依製造商說明書處理用過之電池[...]