Philips 97 (1) Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96

Zur Seite of

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Philips 97 (1) an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Philips 97 (1), sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Philips 97 (1) die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Philips 97 (1). Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Philips 97 (1) sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Philips 97 (1)
- Den Namen des Produzenten und das Produktionsjahr des Geräts Philips 97 (1)
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Philips 97 (1)
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Philips 97 (1) zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Philips 97 (1) und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Philips finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Philips 97 (1) zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Philips 97 (1), über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Philips 97 (1) widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    19" LCD Color Monitor Chassis: HUDSON 9 S e r v i c e S e r v i c e Service Description Page Descripti on Page P a g e SAFETY NOTICE ANY PERSON A TTEMPTING TO SER VICE THIS CH ASSIS MUST F AMILIARIZE HIMSELF WITH THE CHASSIS AND BE A W ARE OF THE NECESSARY SAF ETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC EQUIPMEN T CONT AINING HIGH VOL[...]

  • Seite 2

    HUDSON 9 2 Revision List Version Release Date Revision History A00 Apr .02, 2008 Initial release, Draft V ersion Add CTV Model 190V9FB/27, 190V9FB05 and 190V 9FB/00 A01 Apr .10, 2008 Add CTV Model 190V9FB/97 and it’ s Philips 12NC A02 Apr .17, 2008 Add two new panels for 1 90V9FB/97 A03 Apr .30, 2008 Add CTV Model 190V9FB/93 and 190V9FB/94 A03 Ma[...]

  • Seite 3

    HUDSON 9 3 Import ant Safety Notice Proper service and rep air is important to the safe, reliabl e ope ration of all Philips Comp any Equipment. The service procedures recommended by Philips and described in this service manual a re effective metho ds of performing service operations. Some of these se rvice operations require the use of t ools spec[...]

  • Seite 4

    HUDSON 9 4 1. Monitor S pecifications http://www.wjel.net[...]

  • Seite 5

    HUDSON 9 5 2. LCD Monitor Description The LCD monitor will co ntain a mai n board, a power board an d a key board which hou se the flat panel control logic, brightness control logic and DDC. The power board will provide AC to DC Inverter voltag e to drive the backlight of panel and the main board chi ps each voltage. Monitor Block Diagram AC-IN 100[...]

  • Seite 6

    HUDSON 9 6 3. Operating Instructions 3.1 General Instructions Press the power button to turn the monitor on or of f. The other control buttons are located at the front of the panel of the monitor . By changing these settings, the picture can be adjusted to your per sonal preference s. - The power cord should b e connected. - Connect the video cable[...]

  • Seite 7

    HUDSON 9 7 Rear View http://www.wjel.net[...]

  • Seite 8

    HUDSON 9 8 3.3 Adjusting the Picture Description of the On Screen Display When you press the button on the front control of your monitor, the On-Screen Display (OSD) Main Controls window will pop up and you can then st art making adjustments to your monitor's various features. Use the keys to make your adjustments. T o Lock/Unlock OSD fun ctio[...]

  • Seite 9

    HUDSON 9 9 The OSD Tree Below is an overall view of the stru cture of the On-Screen Di spla y. You can use this as a refe rence when you want to work your way around the different a djustments later on. http://www.wjel.net[...]

  • Seite 10

    HUDSON 9 10 3.4 Connecting to the PC 1) Connect the power cord to the back of the monitor firmly. 2) Connect to PC (a) Turn off your computer and unplug its power cable. (b) Connect the monitor si gnal cable to the video connector on the back of your computer. (c) Plug the power cord of your co mputer and your monitor into a nearby outlet. (d) Turn[...]

  • Seite 11

    HUDSON 9 11 4. Input/ Output Specification 4.1 Input Signal Connector Analog connectors Pin No. Description Pin No. Description 1. Red video input 9. DDC +5V 2. Green video input 10. Logic Ground 3. Blue video input 1 1. Ground 4. Sense (GND) 12. Serial data lin e (SDA) 5. Cable detect (GND) 13. H. Sync/ H+ V . Sync 6. Red video ground 14. V . Sync[...]

  • Seite 12

    HUDSON 9 12 4.3 Pixel Defect Policy http://www.wjel.net[...]

  • Seite 13

    HUDSON 9 13 http://www.wjel.net[...]

  • Seite 14

    HUDSON 9 14 http://www.wjel.net[...]

  • Seite 15

    HUDSON 9 15 4.4 Failure Mode Of Panel  Fai lu re de scri pt io n Phe nom enon V ert ica l bloc k de fec t V erti ca l dim line s V er tica l li nes de fe ct (Alw ays br i g ht or da rk ) Ho riz on ta l bloc k defe ct Hori zontal d im l i nes Hori zontal l i nes defe ct (Alw ays br i g ht or da rk ) Has br i g ht or da rk pi xel Pol ari zer ha[...]

  • Seite 16

    HUDSON 9 16 5. Block Diagram 5.1 Sof tware Flow Chat 1 2 N Y 5 Y N 10 Y N 12 Y N 7 Y N 6 4 3 8 9 14 11 13 Y N 15 Y N 16 17 19 Y N 18 http://www.wjel.net[...]

  • Seite 17

    HUDSON 9 17 1) MCU initialize. 2) Is the EPROM blank? 3) Program the EPROM by default values. 4) Get the PWM value of brightness from EPROM. 5) Is the power key pressed? 6) Clear all global flags. 7) Are the AUT O and SELECT key s pressed? 8) Enter factory mode. 9) Save the power key stat us into EPROM. T urn on the LED and set it to green color . [...]

  • Seite 18

    HUDSON 9 18 5.2 Electrical Block Diagram 5.2.1 Main Board Flash Memory SST25VF010A-33-4C (U402) Panel Interface (CN403) Crystal 14.31818MHZ (X401) Keypad Interface (CN401) Scalar TSUM1PFR-LF (Include MCU, ADC, OSD) (U401) D-Sub Connecto r (CN101) EEPROM AZC099-04S (U103) H sync V sync RGB VGA_SDA, VGA _ SCL EEPROM M24C16 (U403) EEPROM AZC099-04S (U[...]

  • Seite 19

    HUDSON 9 19 5.2.2 Inverter/Power Board DIM DIM EMI filter S t art Circuit: R904 、 R905 、 R906 PWM Control IC Tr a n s f or m e r AC input 16V ON/OFF Control PWM Control IC Feedback Circuit Output Circuit T ransfor mer MOSFET Over V oltage Lamp ON/OFF 5V Bridge Rectifier and Filter Feedback Circuit Rectifier diodes http://www.wjel.net[...]

  • Seite 20

    HUDSON 9 20 6. Schematic 6.1 Main Board 715G2904-1 1 1 2 2 3 3 4 4 5 5 A A B B C C D D XGA/SXGA TSUM16FWR SCHEMATIC LVDS OUTPUT Top 04.Output CMVCC PB[0..9] PA[0..1] PPWR_ON# PA[4..9] 02.Input DSUB_R+ DSUB_G+ DSUB_B+ DSUB_V DSUB_R- DSUB_G- DSUB_B- DET_CABLE DSUB_H DSUB_SOG DDC1_SDA DDC1_SCL DSUB_5V CMVCC1 VCC3.3 03.Scalar DSUB_R+ DSUB_G+ DSUB_SOG D[...]

  • Seite 21

    HUDSON 9 21 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 A A B B C C D D E E CN101 B3 C101 A7 C102 A4 C103 A4 C104 A6 C105 B7 C106 B7 C107 B7 C108 C6 C109 C7 C110 C7 C111 C6 C113 C7 C114 E3 C115 D3 FB101 C5 FB102 A5 FB103 B5 R101 A3 R102 A4 R103 A4 R104 A6 R105 A3 R106 A3 R107 A6 R108 B6 R109 B6 R110 B2 R111 B6 R112 B6 R113 B2 R114 C6 R115 C6 R116 C6 R117 C6 R1[...]

  • Seite 22

    HUDSON 9 22 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 11 11 A A B B C C D D E E F F G G H H LVDS Max condition f or LED: 1. Vcc = 3.3 V 2. Current = 12 mA FW need to be modified. For NVRAM Without NVRAM U403 C419 R433 R434 R435 R436 R437 NC NC NC NC NC NC NC M24C04-WMN6TP 0.22uF16V 10K 1/16W 5% 10K 1/16W 5% 10K 1/16W 5% 100R 1/16W 5% 100R 1/16W 5% [...]

  • Seite 23

    HUDSON 9 23 1 1 2 2 3 3 4 4 5 5 A A B B C C D D S D 2 3 AO3401L 1 G CN403 A5 C419 C2 C420 A4 C421 C3 FB402 C3 Q404 C2 Q405 C3 R433 C2 R434 A4 R435 C1 R436 C2 Output PA1 PA8 PB2 PB6 PB2 PA9 PB3 PB5 PB8 PB8 PA0 PB2 PA5 PA6 PB6 PB9 PB[0..9] PA9 PB3 PA[0..1] PB1 PA1 PA7 PB5 PA[4..9] PA6 PA4 PB4 PA0 PB0 PA5 PB0 PA8 PB7 PA4 PB1 PB4 PA7 PB7 PB9 PB3 PPWR_O[...]

  • Seite 24

    HUDSON 9 24 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 A A B B C C D D E E BAV99 NC D401 LG OTHER NC 0Ohm 1/16W R458 Due to LG doen't request PC'99 Function. U404 can use package 232 or 252. CN404 B1 C422 D6 C423 B7 C425 B3 C426 D5 C427 D7 C428 D5 C432 B7 D401 A2 D402 B2 FB403 C6 Q406 B4 Q408 D3 Q409 B6 Q410 B6 R437 B4 R439 B4 R440 B4 R441 C1 R442 D[...]

  • Seite 25

    HUDSON 9 25 6.2 Power Board 715G2824-1 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 A A B B C C D D E E ! ! ! ! ! ! ! ! ! ! ! ! 1500P/2KV ! BD901 A1 CN901 D1 CN902 D6 C900 D4 C901 D1 C902 D1 C903 C1 C904 B1 C905 B2 C906 B3 C907 B3 C908 B3 C909 C3 C912 A5 C915 B6 C917 B5 C918 B6 C920 D4 C921 C4 C924 C4 C928 C3 C929 B5 C931 E6 C932 B7 C939 B5 D900 B3 D901 B3 D903[...]

  • Seite 26

    HUDSON 9 26 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 A A B B C C D D E E CN801 A7 CN802 A7 CN803 C7 CN804 C7 C801 B3 C802 B3 C803 C1 C804 C1 C805 C2 C806 C2 C807 C3 C808 C3 C809 C4 C810 C4 C811 B4 C812 B4 C813 D2 C814 D3 C815 D4 C816 A6 C817 B6 C818 B6 C819 A7 C820 A7 C821 C6 C822 C7 C823 D6 C824 B6 D801 A4 D802 A4 D803 B4 D804 B4 D805 D4 D806 C4 D807 C4 D8[...]

  • Seite 27

    HUDSON 9 27 6.3 Key Board 715G3016-1 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 A A B B C C D D E E (OK) (UP) (DOWN) CONNECTOR (MENU) LED (Power) CN001 B1 C001 B2 C002 B2 C003 B3 C004 B3 C005 B4 C006 C7 C007 C5 C008 C5 C009 C6 C010 C8 LED001 A3 R001 B4 R002 B4 R004 B4 R005 B4 R007 C3 SW001 C7 SW002 C6 SW003 C8 SW004 C6 SW005 C5 ZD001 C7 ZD002 C5 ZD003 C8 ZD00[...]

  • Seite 28

    HUDSON 9 28 7. PCB Layout 7.1 Main Board 715G2904-1 C101 B2 FB101 B2 R418 B1 C102 B2 FB102 B2 R419 B1 C103 B2 FB103 B2 R420 B1 C104 B2 FB401 B2 R421 B1 C105 B2 FB402 A2 R424 B2 C106 B2 FB403 A1 R425 B2 C107 B2 FDT2 ?1 R426 A2 C108 B2 FDT3 ?6 R427 B1 C109 B2 Q404 A2 R428 B1 C110 B2 Q405 A2 R429 B1 C111 B2 Q406 B1 R430 B1 C113 B2 Q408 B1 R431 B1 C114[...]

  • Seite 29

    HUDSON 9 29 http://www.wjel.net[...]

  • Seite 30

    HUDSON 9 30 7.2 Power Board 715G2824-1 BD901 D3 J821 B2 BD901A D3 J823 B1 BD901B D3 J824 B2 C604 D4 J825 C2 C812 B2 J826 D1 C816 C1 J829 C4 C817 B1 J830 D1 C819 A1 J831 D1 C820 B1 J832 D4 C821 C1 J833 D3 C822 C1 J834 D1 C824 C1 J835 D4 C900 B3 J836 C4 C901 D2 J837 D4 C902 D2 J838 D4 C903 D2 J901 C4 C905 C3 J902 C3 C905A C3 J903 C3 C906 B3 J904 B2 C[...]

  • Seite 31

    HUDSON 9 31 C601 D3 R818 A2 C602 D4 R819 A2 C603 D4 R820 A2 C606 D3 R821 A2 C608 D3 R822 B2 C609 D3 R823 A2 C610 D3 R824 A2 C611 D3 R825 B2 C612 D3 R826 B2 C613 D3 R827 D1 C801 B2 R829 C1 C802 C2 R830 C1 C803 B2 R836 B1 C804 B2 R837 A1 C805 A2 R838 A1 C806 B2 R839 A1 C807 A2 R840 A1 C808 A2 R841 A1 C809 B2 R842 A1 C810 A2 R843 A1 C811 B2 R844 A1 C8[...]

  • Seite 32

    HUDSON 9 32 7.3 Key Board 715G3016-1 CN001 A3 G N D 1 A 1 G N D 2 A 3 LED001 A2 SW001 A1 SW002 A2 SW003 A1 SW004 A2 SW005 A3 C001 A3 C002 A2 C003 A2 C004 A3 C005 A1 C006 A1 C007 A3 C008 A2 C009 A2 C010 A1 R001 A1 R002 A1 R003 A2 R004 A2 R005 A2 R007 A3 ZD001 A1 ZD002 A3 ZD003 A1 ZD004 A2 ZD005 A2 http://www.wjel.net[...]

  • Seite 33

    HUDSON 9 33 8. Wiring Diagram Main Board 9Pin 30 Pin Panel D-SUB TSUM1PFR-LF U401 CN403 89G179J30N501 FFC Cable 1 9 CN404 Pin 1 6 CN401 Power Board Key Board 6 Pin A C IN CN902 1 14 CN802 CN801 CN804 CN803 CN901 6 1 CN001 95G 82014X507 HARNESS 14P (SAN)-9P 1 30 14Pin CN101 HARNESS6P (SANW)-6P 95G820H 6D509 http://www.wjel.net[...]

  • Seite 34

    HUDSON 9 34 9. Scalar Board Overview Morning St ar chip Flash ROM EEPROM D-SUB D-SUB DC-DC Converter s DC-DC Converter s http://www.wjel.net[...]

  • Seite 35

    HUDSON 9 35 10. Mechanical Instructions 1. Back Vie w as Fig1 Place the monitor face down on a smo oth surface as Fig 1. Be careful to avoid scratch and injury du ring the uninstallation. Fig1 2. Remove the hinge as Fig2. Remove the three scre ws remarked in red to remove the hinge as Fig2. Fig2 http://www.wjel.net[...]

  • Seite 36

    HUDSON 9 36 3. Remove bezel and rear cov er as Fig3~ Fig5. Fig3 Fig4 http://www.wjel.net[...]

  • Seite 37

    HUDSON 9 37 Fig5 4. Remove main frame cover as Fig6~Fig7. a. Remove the two screws marked in red as Fig6. b. Disconnect the four connector marked in blue as Fig6. c. Remove the two screws marked in red as Fig7. Fig6 Fig7 http://www.wjel.net[...]

  • Seite 38

    HUDSON 9 38 5. Remove power board as Fig8. a. Remove the two screws marked in red as Fig8. b. Disconnect the connector marked in blue as Fig8. Fig8 6. Remove scalar board as Fig9~Fig10. a. Remove the screw remarked in red as Fig9. b. Disconnect the t w o connectors marked in blue as Fig9. c. Remove the two screws remarked in red as Fig10. Fig9 Fig1[...]

  • Seite 39

    HUDSON 9 39 1 1. T rouble Shooting This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact P hilips customer service representativ e. http://www.wjel.net[...]

  • Seite 40

    HUDSON 9 40 http://www.wjel.net[...]

  • Seite 41

    HUDSON 9 41 12. Rep air Flow Chart 12.1 Main Board (1). No Power No power Press power key and look if the picture is normal Please reinsert and make sure the AC of 100-240 is normal Reinsert or check the Adapter/Inverter section X401 oscillate waveforms are normal Check U404, Q409 and Q4 10 Replace U401 Replace X401 OK OK OK NG NG NG NG Measure U40[...]

  • Seite 42

    HUDSON 9 42 (2). No Picture No picture The button if under control Replace U401 Replace X401 Measure U404 PIN2=3.3V Q409 V collector =1.8V Check Correspondent component Replace U401 X401 oscillate waveform is normal Check U404, Q409 and Q4 10 OK OK OK OK OK NG NG NG NG Check reset c ircuit of U401 is normal Check HS VS from CN101 is normal Replace [...]

  • Seite 43

    HUDSON 9 43 (3). White screen White screen Check Q404, Q405 is bro ken or CN403 solder? Check Correspond ent com p onent. Re p lace Panel Check Correspondent com p onent. Replace U401 OK OK Replace X401 OK NG NG NG NG Check reset c ircuit of U401 is normal OK X401 oscillate waveform is normal Measure Q404 base is low level? http://www.wjel.net[...]

  • Seite 44

    HUDSON 9 44 1 1.2. Power/Inverter Board (1) No power Check ZD902 (-) = 16V Check AC line volt 1 10V or 220V Check AC input Check the voltage of C9 05 (+) Check bridge rectified circuit and F901 circuit Check sta rt voltage for the pin3 of IC901 Check R904, R905, R90 6 and Change IC901 NG Check the auxiliary voltage is bigger than 10V and smaller th[...]

  • Seite 45

    HUDSON 9 45 (2) W / LED, No Backlight Check CN902 pin4 = 16V NG OK Check adapter or MB Check ON/OFF sign al Check Interface board NG OK Check IC801 PIN2=5V NG OK Check Q801 and ZD801 Check IC801 PIN1, 15 have the output of square wav e at short NG OK Change IC801 Check Q805 and Q806 PIN5, 6, 7, 8 have the output of square wa ve at short time. NG OK[...]

  • Seite 46

    HUDSON 9 46 12.3 Key Board OSD is unstable or not working Is Key Pad Board connecting normally? Connect Key Pad Board Is Button Switch normally? Replace Button Switch Y N N Is Key Pad Board normally? Replace Key Pad Board Y N Y Check Main Board http://www.wjel.net[...]

  • Seite 47

    HUDSON 9 47 13. ISP Instruction 1. When do the p art, need the tools as follo w: a. An i486 (or above) personal computer or comp atible. b. Microsoft operatio n system Windows 95/98/2000/XP . c. “ PORT95 NT .exe” program d. Software IS P SN Alignment kits The kit contents: a. ISP BOARD x1 b. Printer cablex1 c. VGA cable x1 2. Inst all the “PO[...]

  • Seite 48

    HUDSON 9 48 http://www.wjel.net[...]

  • Seite 49

    HUDSON 9 49 http://www.wjel.net[...]

  • Seite 50

    HUDSON 9 50 Click to complete the installation. http://www.wjel.net[...]

  • Seite 51

    HUDSON 9 51 Note: After inst allation, you must restart t he PC to take the setup to ef fect. 3. Connect the ISP board as follo w: Connect to the PC LPT Connect to the Philip s 190V9 http://www.wjel.net[...]

  • Seite 52

    HUDSON 9 52 4. The process of ISP w rite is as follows. a. Double-click , running the program a s follows: http://www.wjel.net[...]

  • Seite 53

    HUDSON 9 53 b. Click icon, search the program” 190V9_TSUM1PFR_L M190E08_TLL_2008031 9_V101”, and click open: http://www.wjel.net[...]

  • Seite 54

    HUDSON 9 54 c. Click icon, it will auto run. If burn in succe ss, it will show as the follow picture: http://www.wjel.net[...]

  • Seite 55

    HUDSON 9 55 14. DDC Instruction General DDC Data R e-programming In case the main EEPROM with Software DDC which store all factory settings were replaced because a defect, repaired monitor’ the se rial numbers have to be re-programm ed. It is advised to re- soldered the main EEPROM with Software DDC from the old board onto the new board if circui[...]

  • Seite 56

    HUDSON 9 56 2. Inst all the “WinDDC_ setup” Second, you must in stall the . The proce ssing as follows: http://www.wjel.net[...]

  • Seite 57

    HUDSON 9 57 http://www.wjel.net[...]

  • Seite 58

    HUDSON 9 58 Click to complete the installation. 3. Connect the DDC board as follow: Connect to the PC LPT When you write analog EDID, Connect this port to the Philips 190V9’ s VGA port 12V Input http://www.wjel.net[...]

  • Seite 59

    HUDSON 9 59 4. T ake analog DDC write for example, as follo w a. Double-click , appear as follow Figs : http://www.wjel.net[...]

  • Seite 60

    HUDSON 9 60 b. Click . c. Key 14 numbers in the Serial Number blank, then c lick “OK”. Now analog DDC Write completes, a s follow . http://www.wjel.net[...]

  • Seite 61

    HUDSON 9 61 190V9 EDID Analog 128 bytes EDID Data (Hex): 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 0: 00 FF FF FF FF FF FF 00 41 0C 20 C0 01 01 01 0 1 16: 0C 0B 01 03 0E 26 1E 78 2A A1 50 A3 57 4C 9D 25 32: 11 50 54 BF EF 80 71 4F 81 40 81 80 01 01 01 01 48: 01 01 01 01 01 01 30 2A 00 98 51 00 2A 40 30 70 64: 13 00 78 2D 11 00 00 1E 00 00 00 [...]

  • Seite 62

    HUDSON 9 62 White y: 0.3291015625 <-x-Color Characteri stics-x-> <---Established Timings---> Established Timings 1: BF -720x400 @70Hz VGA,IBM -640x480 @60Hz VGA,IBM -640x480 @67Hz Apple,Mac II -640x480 @72Hz VESA -640x480 @75Hz VESA -800x600 @56Hz VESA -800x600 @60Hz VESA Established Timings 2: EF -800x600 @72Hz VESA -800x600 @75Hz VESA[...]

  • Seite 63

    HUDSON 9 63 15. White Balance, Luminance Adjustment 1. Apparatuses and program: analyzer CA-2 10, PC, tool, FGA adjustment progra m (PHILIPS170V9.DDCI), Pattern generator . 2. Equipment installation: a. Connect analyzer CA-210 to PC by USB connector , in stall drive program CA-SDK V er4.00 for CA-210 and restart PC af ter finish instal ling. b. Ins[...]

  • Seite 64

    HUDSON 9 64 4. Color T emp confirmatio n Connect the signal to the monitor , the monitor display wh ite-picture, use CA-2 10 to m easure the Color T e mp of the screen center and select the OS D to make sure whether the Co lor T emps accord with the SPEC. http://www.wjel.net[...]

  • Seite 65

    HUDSON 9 65 16. Monitor Exploded V iew 1 2 3 4 5 6 7 8 12 3 45 6 7 8 F E D C B A 190V9 8 7 6 5 4 3 2 1 A B C D E F Item Part No . 1 2 3 4 5 6 7 8 BEZEL PANEL SCALAR BOARD AS SY POWER BOAR D ASSY REAR COVER 19 0V9 STAND_BASE ASS'Y KEY BOARD ASSY KEY PAD http://www.wjel.net[...]

  • Seite 66

    HUDSON 9 66 17. Recommended & S p are Part s List 190V9FB/97(1) Item Location Philips 12NC PCM Codes Description 1 FQ106 996510017730 Q34G0368ADTE1B0130 BEZEL_190V 2 E750 996510016251 750GLG190E8G23 N000 P ANEL LM19 0E08-TLG2 GZ LGD 2 E750 996510016074 750GLG190E8G43 N000 P ANEL LM19 0E08-TLG4 GZ LGD 2 E750 996510016443 750GLH90N3A12N P ANEL HS[...]

  • Seite 67

    HUDSON 9 67 U402 996510015572 705GQ7 56218 MCU ASS'Y(HSD) IC903 996500036055 056G 139 3A IC PC123Y22FZ0F IC901 996510014843 056G 379 98 IC LD7552DPS SOP-8 IC801 996500036059 056G 608 10 IC OZ9938GN-B SOIC-16 IC904 996510002780 056G 158 10 T IC AZ431AZ-AE1 T O-92 BY AAC PT801 996510014840 S80GL1 9T32V TRANSFORMER ASSY PT801 996510014836 080GL19[...]

  • Seite 68

    HUDSON 9 68 18. Different Part s List Diversity of 190V9FB/62(1) comp ared with 190V9FB/97(1) 190V9FB/62 (1) 190V9FB/97 (1) Location Philip s 12NC PCM Codes De scription Philip s 12NC PC M Codes Description FQ205 705GQ83400 6 CUSHION ASSY 996510016252 705GQ8CS006 CUSHION ASSY Diversity of 190V9FB/27(1) comp ared with 190V9FB/97(1) 190V9FB/27 (1) 19[...]

  • Seite 69

    HUDSON 9 69 Diversity of 190V9FB/93(1) comp ared with 190V9FB/97 (1) 190V9FB/93(1) 190V9FB/97 (1) Location Philip s 12NC PCM Codes De scription Philips 12NC PCM Codes Description FQ301 089G414A15N IS POWER CORD 996510015663 089G404A15N IS POWER CORD FQ106 Q34G0368ADTF1B0130 BEZEL_190V 996510017730 Q34G0368ADTE1B0130 BEZEL_190V FQ202 Q44G91 14813 2A[...]

  • Seite 70

    HUDSON 9 70 Diversity of 190V9FB/94(2) comp ared with 190V9FB/97 (1) 190V9FB/94(2) 190V9FB/97 (1) Location Philips 12NC PCM Codes De scription Philip s 12NC PC M Codes Description F901 996510006276 084G 56 4W FUSE 4.0A 250V 996510013724 084G 56 4 B FUSE 4A 250V F903 996510006276 084G 56 4W FUSE 4.0A 250V 996510013724 084G 56 4 B FUSE 4A 250V T901 9[...]

  • Seite 71

    HUDSON 9 71 19. General Product S pecification CONTENTS 1 FOREWORD 2 PRODUCT PROFILE 2.1 LCD 2.2 SCANNING FREQUENCIES 2.3 AMBIENT TEMPERA TURE: 0 ° C - 40 ° C 3 ELECTRICAL CHARACTERISTICS 3.1 INTERF ACE SIGNALS 3.2 INTERF ACE 3.3 TIMING REQUIREMENT 3.4 HORIZONT AL SCANNING 3.5 VERTICAL SCANNING 3.6 POWER INPUT CONNECTION 3.7 POWER MANAGEMENT 3.8 [...]

  • Seite 72

    HUDSON 9 72 6. ENVIRONMENT AL CHARACTERISTICS 6.1 SUSCEPTIBILITY OF DISPLA Y TO EXTERNAL ENVIRONME NT 6.2 TRANSPOR T A TION TESTS 6.3 DISPLA Y DISTURBANCES FROM EXTERNAL ENVIRONMENT 6.4 DISPLA Y DISTURBANCES TO EXTERNAL ENVIRONMENT 7. RELIABILITY 7.1 MEAN TIME BETWEEN F AILURES 8. QUALITY ASSURANCE REQUIREMENTS 8.1 ACCEPT ANCE TEST 9. PHILIPS’ FL[...]

  • Seite 73

    HUDSON 9 73 1. FOREWORD T his specification describ es a 19" SXGA multi-scan color TFT LCD monitor with maximum resol ution up to 1280 x 1024 /75 Hz non-interlace d. All optical characteristics (i ncluding WHITE-D, Brightness, and so on) are determined according to panel sp ecification after warming up approxi mate 30 minutes that brightn ess [...]

  • Seite 74

    HUDSON 9 74 Color gamut : 72% G a t e I C : N o v a t e k S o u r c e I C : N o v a t e k R e s p o n s e t i m e : 5 m s 2.2 Scanning frequencies Hor . : 30 – 83 K Hz V er .: 56 - 76 Hz Video dot rat e: 165 MHz (140MHz for EDID) Power input: 90-264 V AC, 50/60 ± 2 Hz Power consumption : : 36 W typical Functions: D-SUB analog R/G/B sep arate inp[...]

  • Seite 75

    HUDSON 9 75 10 Logic GND 1 1 Sense (GND) 12 Bi-directional data 13 H/H+V sync 14 V -sync 15 Data clock 3.3 Timing requiremen t Factory Preset mode definition : 1. Perfect FOS while presenting all required timings. 2. Required timings need t o be specified in User's Manual User mode 1. It can be showed visibly(not ov er scalar or Panel spec.) 2[...]

  • Seite 76

    HUDSON 9 76 DMT 1024x768/85 94.50 68.68 85.00 808 p / p 1152x864/60 79.90 54.00 60.00 900 p / p 1152x864/70 94.50 63.90 70.00 912 p / p DMT 1152x864/75 108.00 67.50 75.00 900 p / p MAC 1152x870/75 100.00 68.68 75.06 915 n / n SUN 1152x900/66 92.94 61.80 65.95 937 p / p SUN 1152x900/76 105.56 71.71 76.05 943 p / p CVT 16:9 1280x720/60 74.50 44.77 59[...]

  • Seite 77

    HUDSON 9 77 3.3.3 Software control functions via OSD / control adjust able functions: Any deviation, then refer to PVT Exit sample. Please refer to following Hudson8 OS D definitions Level 1 Level 2 Level 3 Default Picture Brightness (0~100) 100 Contrast (0~100) 50 Color Color Temp. (5000K,65 00K,7500K,8200K,9300K,11500K) 6500K sRGB User Define (Re[...]

  • Seite 78

    HUDSON 9 78 3.7 Power management The monitor must comply with the Microsoft on Now spe cification, and meet EP A requirements. Mode HSYNC VSYNC Video Po w er-cons. Indication Rec. time Power-On On On active 36W T yp. Green LED -- off Off Off blanked < 1W Amber LED < 3 s DC Power Of f N/A < 1W LED Off 3.8 VGA Display identification In accor[...]

  • Seite 79

    HUDSON 9 79 signal sources must have 75 ohm outp ut impedance. (2) Luminance setting : controls to be set to 300 nits (typical ) with full screen 100 % duty cycle white signal (3) Warm up: more than 30 minutes after po wer on with signal supplied. (4) Ambient light: 400 -- 600 lux. (5) Ambient temperature: 20 ± 5 ° C 4.2 Brightness Just follow pa[...]

  • Seite 80

    HUDSON 9 80 6500K/sRGB x = 0.313 ± 0.02 y = 0.329 ± 0.02 sRGB x = 0.313 ± 0.02 y = 0.329 ± 0.02 5000K x = 0.346 ± 0.02 y = 0.359 ± 0.02 Production alignement specification CIE coord inates (x,y) 1 1500K x = 0.272 ± 0.005 y = 0.283 ± 0.005 9300K x = 0.283 ± 0.005 y = 0.297 ± 0.005 8200K x = 0.292 ± 0.005 y = 0.307 ± 0.005 7500K x = 0.299[...]

  • Seite 81

    HUDSON 9 81 5.7 Resins z RoHS required z WEEE required. z Resin type/selection refer to Project Book Section 7.2 Plastic mate rial. 5.8 If p aint is used z RoHS required z WEEE require z If new painting type need to implement, refer to UN-D 1235. 5.9 Plastic mold tooling z T ooling to be designed to minimize cosmetic defe cts induced by molding pro[...]

  • Seite 82

    HUDSON 9 82 H :| L-R | ≤ 1. 5 ㎜ V :| U-D | ≤ 1. 5 ㎜ 2.Black side on the lef t and right is symmetrical, not cut side. z Gap between bezel and rear cover 0.4 mm ( Ty p . ) z S tep between bezel and rear cover Left, right and top : ≤ 0.6mm Bottom and corner: ≤ 1.1mm z "Wobbl e", "T wist", etc (front to [...]

  • Seite 83

    HUDSON 9 83 The following sections define the interfe rence and susceptibility condition limits t hat might occur between external environment and the display device. 6.1 Susceptibility of display to external environment Operating - T emperature : 0 to 35 degree C - H u m i d i t y : 8 0 % m a x - Altitude : 0-3658m - Air pressure : 600-1 100m BAR [...]

  • Seite 84

    HUDSON 9 84 BLACK DOT DEFECTS ACCEPT ABLE LEVEL MODEL 190V9 1 dark sub-pixel 5 2 adjacent dark sub-pixel s 2 3 adjacent dark sub-pixel s (one white pixel) 1 Distan ce between two black dot s 15mm Black dot defects within 2 0 mm circle* 1 T otal black dot defect s of all type 5 TOT AL D OT DE FE C TS ACCEPT ABLE LEVEL MODEL 190V9 T otal bright or bl[...]

  • Seite 85

    HUDSON 9 85 Fig 1: Measurement locations of Brightness Uniformity Fig 2: Cross t alk p attern Gray level 46 (64 Gray level) YA 1/2 1/2 1/6 Fig 3: Cross talk Pattern Center at Gray lev el 0 (Black) YB 1/2 1/2 1/6 1/3 1/3 1/3 1/3 1/3 http://www.wjel.net[...]

  • Seite 86

    HUDSON 9 86 D VIDEO C E SEPARATE SYNC. HORIZ ONTAL B A R VIDEO Q S P O D VIDEO C E B A VERTICA L HORIZ ONTAL COM PO SITE S YN C. FIG-4 TIMING CHAR T -1 http://www.wjel.net[...]

  • Seite 87

    HUDSON 9 87 10. REGULA T OR Y COMPLIANCE 10.1 World wide Regulatory Region (RSO) Country (NSO) Domain Safety / EMC / Ergonomics / Standards Documents Reference Logo Applicant Mandatory V-Line Sample Q'ty Remark World wi de World wide Sa IEC60950-1:2001. Group and national differences of all countries listed in CB Bulletin No. 107A CB Report, c[...]

  • Seite 88

    HUDSON 9 88 E European Electromagnetic Compatibility Directive 2004/108/EC EN55022:2006, EN55024:1998+A 1:2001+A2:2003, EN61000-3-2:200 6, EN61000-3-3:199 5+A1:200 1+A2:20 05 EMC/CE test report OEM Yes Yes HDMI have to test PC mode and DVD mode Sa EN60950-1:2001 TUV certificate OEM Optional No Philips is OEM license holder O LCD: ISO13406-2, pr EN [...]

  • Seite 89

    HUDSON 9 89 O TUV MPR-II TUV MPR-II certificate OEM Optional No Philips is OEM license holder Sa EN60950-1:2001 SEMKO certificate OEM Optional No Philips is license holder O TCO'99 TCO report and certificate OEM Optional No To add all sales name into certificate O TCO'03, or TCO'0x supersedes new standard TCO report and certificate O[...]

  • Seite 90

    HUDSON 9 90 and /00, /05, /69 into certificate. O EMF EN 50392 EN 50392 report Yes No 1 set Supplier ship out 1 samples to Netherlands and provide EN50392 report (test fee 750EU) Sa EN60950-1:2001 Certificate of Conformity Philips Yes Yes Eastern Europe E EN55022,EN5502 4, IEC61000-3-2 ,IE C61000-3-3 Certificate of Conformity Philips Yes Yes 3 sets[...]

  • Seite 91

    HUDSON 9 91 Sa Korean Safety Control law IEC 60950 EK certificate OEM Yes No NOT REQUIRED KOREA E Regulations laws: EMI 1996-78, 80. EMS 1996-79,81 MIC certificate OEM Yes No NOT REQUIRED SINGAPOR E Sa IEC60950 PSB certificate OEM Yes Yes Supplier to provide local representative Sa GB4943-2001 CCC certificate OEM Yes Yes E GB9254-1998; 17625.1-2003[...]

  • Seite 92

    HUDSON 9 92 AUSTRALIA / NEW-ZEAL AND E AS/NZS3548:199 5 AS/NZS CISPR22: 2002 Class B CB, EMC report OEM Yes Yes 1 set Supplier ship out 1 sample to Australia and pay transportation cost, Supplier to apply for C-Tick through Philips NSO Saudi Arabia Sa EN60950-1:2001 SASO OEM Yes Yes Saudi Arabia Sa EN55022, EN61000-3-2, EN61000-3-3, EN55024 SASO OE[...]

  • Seite 93

    HUDSON 9 93 E FCC Part 15 Class B FCC report and DOC OEM Yes Yes To list manufacture in FCC report O Energy Star EPA test data OEM Optional No Sa CSA C22.2 No 60950 CSA certificate or CUL OEM Optional No CANADA E ICES-003 issue 3 Statement on label OEM Yes Yes MEXICO Sa NOM-019-SC FI-1 994 NOM certificate Philips Yes No 2 sets NOT REQUIRED Argentin[...]

  • Seite 94

    HUDSON 9 94 Sa SABS IEC 60950 and IEC 60950-1 Certificate of Conformity Philips Yes Yes South Africa SOUTH AFRICA E EN55022 or Crisper 22 Certificate of Conformity Philips Yes Yes Supplier to provide CB, EMC report Sa = Safety E = Electromagnetic Compatibility O = Other which including recycli ng, energy saving, ergonomics, Green Ma rk X=X-Ray Rema[...]

  • Seite 95

    HUDSON 9 95 10.2 EMC Requirement s Supplier DVT EMI test result must be submitted pri or to DVT samples delivery , and PVT EMI test result must be submitted again prior to PVT samples delivery , which also has to meet Philips' immuni ty testing specification. 10.3 RoHS Restriction on the use of cert ain hazardous sub stances. Lead, Cadmium, Me[...]

  • Seite 96

    HUDSON 9 96 TELEVISION/MONITOR SAFFTY GUIDELINES FOR THE PROFESSIONAL SERVICE TECHNICIAN Safety Checks Fire and Shock Hazard Implosion X-radiation After the original service problem has been corrected,a complete safety check should be made. Be sure to check over the entire set, not just the areas where you have worked. Some previous servicer may ha[...]