Perle Systems SDS Bedienungsanleitung

IOLAN SDS/SCS/STS/MDC Command Line Interface Reference Guide Version 3.7 Part #5500210-14 December 2008[...]

Copyright S tatement This document must not be repro duced in any way whatsoever , either printed or electronicall y , without the consent of: Perle Systems Limi ted, 60 Renfrew Drive Markham, ON Canada L3R 0E1 Perle reserves the right to make change s without further notice, to any products to improve reliability , function, or design. Perle, the [...]

IOLAN SDS/SCS/STS/MDC CLI Re ference Guide, V ersion 3.7 3 Preface ........................ ....................................................... 13 About This Book .............. .................................... ...................... 13 Intended Audience ........... .................................... ...................... 13 Typeface Con[...]

4 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 Show Console ............ ................................. ................................. ........... 26 Show Custom-App ............... ........................................................ ........... 26 Show Server ............. ................................................. ...[...]

5 Show TruePort ........... .................................................................. ........... 38 Email Commands ................... .............................. ...................... 39 Set Email-Alert Server . ................. ................................ ............... ........... 39 Show Email-Alert Server ....... .........[...]

6 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 Kill Line ............ ............................................................................. ........... 51 Kill Session............. .......................................... ............................ ........... 51 Logout ................ ................ ......................[...]

7 Set Termtype ......... .......................................... .............. ............... ........... 76 Show Line............ ............................................ .............. ............... ........... 77 Line Service Commands . .................................... ...................... 78 Set Custom-App .......... ..........[...]

8 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 Delete Modem........... ................................................. ................ .............. 97 Set Modem ................ ................................................................. .............. 97 Show Modems ............ ...............................................[...]

9 Show Server ............. ................................................................. ............ 108 Show WINS............... ................................................. ................ ............ 108 Gateway Commands .............. .................................... .............. 109 Add Gateway .............. ...............[...]

10 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Delete VPN Exception.......... ........................................................ ......... 122 Show VPN Exception .... ............................................................ ............ 122 Chapter 6 Time Commands ............................................ 123 Server Comman[...]

11 Netload .............. ............................................ ............................ ............ 130 Netsave ................ ........................................................ .............. ............ 131 Custom Factory Default .. .................................... .................... 132 Netload .............. ........[...]

12 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set Line ................ ...................................................................... 142 Set Line Service ....... ................................................................. ............ 142 Set IOChannel ....................... ...........................................[...]

IOLAN SDS/SCS/STS/MD C CLI Reference Guide, V ersion 3.7 13 Preface About This Book This guide provides the information you need to : z configure the IOLAN using the Command Line Interface (CLI) Intended Audience This guide is for adm inistrators who will be configuring th e IOLAN. Some prerequisite knowledge is needed to understand the concep ts a[...]

Contacting T ech nical Support 14 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Cont acting T echnical Support Making a T echnical Support Query Who T o Cont act If you bought your produ ct from a registered Perle supplier, you must contact their T echnical Supp ort department; they are qualified to deal with you r problem. Have Y our Pr[...]

15 Contacting T echnical Support Rep air Procedure Before sending a IOLAN for repair, you must contact your Perle supplier . If, however , you boug ht your product directly from Perle you can contact direct ly . Customers who are in Europe, Afri ca or Middle East can submit repair d etails via a websit e form. This form is on the Perle website, www[...]

Contacting T ech nical Support 16 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7[...]

IOLAN SDS/SCS/STS/MD C CLI Reference Guide, V ersion 3.7 17 Introduction Chapter 1 1 This book provides the command line interface (CLI) options availabl e for the IOLAN. The commands are grouped by function. CLI Conventions This section explains how to interpret the CLI s yntax. If you are an exis ting IOLAN+ custom er and would like to configure [...]

CLI Conventions 18 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 Command Shortcut s When you type a command, you can specify the shortest unique ve rsion of that command or you can press the ESC or TA B key to complete the command. For example, the following command: set telnet-clie nt map-to-crlf off can be typed as: set tel map off or ,[...]

IOLAN SDS/SCS/STS/MD C CLI Reference Guide, V ersion 3.7 19 Server Commands Chapter 2 2 This chapter defines all the CLI commands a ssociated with configuring the IOLAN server parameters. Server Commands Set Console Set Custom-App Description Sets the flow control and baud rate on IOLAN models that have a dedicated console port. User Level Admin Sy[...]

Server Commands 20 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set Port-Buffering Description Configures port buffering. User Level Admin Syntax set port-buffering [duplicate -nfs-to-syslog on|off] [keys-stroke-buffering on|off] [mode off|local|remote|both] [nfs-directory < text >] [nfs-encryptio n on|off] [nfs-host < config_h[...]

Server Commands 21 Server Commands Set Server Description Sets server parameters. User Level Admin Syntax set server [auto-obtain-dns o n|off] [auto-obtain-gw on|off] [auto-obtain-wins on|off] [banner on|o ff] [break on|off] [bypass-password on|off] [dhcp-update- dns on|off] [domain < string >] [flush-on-close on|o ff] [line-menu-string < [...]

Server Commands 22 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 dhcp-update-dns The DHCP server will update the DNS server when the IOLAN requests a DHCP IP address (the communicati on between the DNS server and the DHCP server must already be set up in your network). dhcp/bootp Enables the DHCP/BOOTP client process in the IOLAN. By def[...]

Server Commands 23 Server Commands password-limit The number of attempts a user is allowe d to enter a password for a serial port connection from the network, before the conn ection is terminated and the user has to attempt to login again. For us ers logging into the serial po rt, if this limit is exceeded, the serial port is disabled for 5 minutes[...]

Server Commands 24 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set SSL Server session-escape-string A configurable string that allows access to a port to view the multisession screen options, allowing the various options while accessing the pa rticular port on the IOLAN. Y ou can specify control (unprintab le) codes by putting the deci[...]

Server Commands 25 Server Commands Set Service validation-criteria Any values that are entered in the validation criteria m ust match the peer certificate for an SSL connection; any fiel ds left blank wi ll not be validated against the peer certificate. country A two character count ry code; for example, US. This fi eld is case sensitive in order t[...]

Server Commands 26 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Show Console Show Custom-App Show Server Show Port-Buffering httpd HTTP daemon process in the IOLAN on port 80. snmpd SNMP daemon process in the IOLAN on port 16 1. spcd SPC (T ruePort) daemon process in the IOLAN that supports T ruePo rt Full Mode on UDP port 668. Y ou can[...]

Server Commands 27 Hardware Commands Show Modbus Hardware Commands Set Ethernet Show Hardware SSH Server Commands Set SSH-Server See Keys and Certificates in the IOLAN User’ s Guide for information abou t th e keys and certificates that need to be uploaded or downloaded with the IOLANs SSH server . Description Shows the Modbus settings for the ga[...]

SSH Server Commands 28 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Show SSH-Server authentication dsa An authentication method used by SSH version 2. Use DSA authen tication for the SSH session. authentication passw ord The user types in a pa ssword for authentication. authentication ke yboard-interactive The user types in a password f[...]

Server Commands 29 SSL/TLS Commands SSL/TLS Commands Set SSL Server Description Sets the default SSL/TLS parameters for the server . User Level Admin Syntax set ssl server [version any|t slv1|sslv3] [type client|server] [verify-peer on|off] [validation-criteria country < code >|state-province < text > |locality < text > |organisat[...]

SSL/TLS Commands 30 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set SSL Server Cipher-suite organisation-unit Up to a 64 character entry fo r the u nit in the organisation; for example, Payroll. This field is case sensitive in order to successfully match the inform ation in the peer SSL/TLS certificate. common-name Up to a 64 character[...]

Server Commands 31 Modbus Commands Show SSL Modbus Commands Set Modbus Gateway key-exchange The type of key to exchange for the encryption format: z Any —Any key exchange that is valid is used (this does not, however , include ADH keys). z RSA —This is an RSA key exchange using an RSA key and certificate. z EDH-RSA —This is an EDH key exchang[...]

Modbus Commands 32 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Show Modbus req-next -delay A delay , in milliseconds, to allow serial sl ave(s) to re-enable receivers before issuing next Modbus Master request. The default is 50 ms. exceptions When enabled, an exception message is gene rated and sent to the initiating Modbus device when[...]

Server Commands 33 Authentication Commands Authentication Commands Set Authentication Set Authentication Local Description Sets the authentication method for the IOLAN. User Level Admin Syntax set authentication type prima ry|secondary none|local|radius|kerberos|ldap|tacacs +|securid|nis [secondary-as-backup on|off] [auth-admin-user-local on|off] O[...]

Authentication Commands 34 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set Authentication Kerberos Set Authentication LDAP Description Configures Kerberos authentication settings. User Level Admin Syntax set authentication kerberos [ kdc-domain < string >] [port < TCP_port >] [realm < string >] Options kdc-d o main Th[...]

Server Commands 35 Authentication Commands Set Authentication NIS Add RADIUS Delete RADIUS Description Sets NIS authentication parameters. User Level Admin Syntax set authentication nis [domai n < string >] [primary < config_host >] [secondary < config_host >] Options domain The NIS domain name. primary The primary NIS host that i[...]

Authentication Commands 36 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set Authentication RADIUS Description Sets RADIUS parameters. User Level Admin Syntax set authentication radius [ac counting on|off] [acct-authenticator on|off] [acct-por t < UDP_port >] [auth-port < UDP_port >] [nas-identifie r < nas_id >] [nas-ip[...]

Server Commands 37 Authentication Commands Set Authentication T ACACS+ Set Authentication SecurID Description Configures T A CACS+ au thentication settings. User Level Admin Syntax set authentication tacacs+ [p ort < TCP_port >] [primary < config_host >] [secondary < co nfig_host >] [secret < string >] Options port The port [...]

T ruePort Ba ud Commands 38 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Show Authentication T ruePort Baud Commands Set T ruePort Remap-Baud Show T ruePort Description Shows the authentication settings. If you ty pe just the show authentication command, the configured primary and sec ondary authenti cation methods are displayed. User L[...]

Server Commands 39 Email Commands Email Commands Set Email-Alert Server Show Email-Alert Server Description Configures email alert se ttings for the server . User Level Admin Syntax set email-alert server [from < email_addr >] [level emergency|alert|critical|er ror|warning|notice|info|debug] [mode on|off] [to < email_addr >] [reply-to &[...]

Clustering Commands 40 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Clustering Commands Add Clustering Slave-IP Delete Clustering Slave-IP Description Adds a slave IOLAN to the clus tering group. User Level Admin Syntax add clustering slave-ip < IPv4 _address > number-of-ports 1|2|4|8|16|24|32|48 [ protocol telnet|ssh] [starting-m[...]

Server Commands 41 Clustering Commands Set Clustering Slave-IP Show Clustering Slave-IP Description Modify the parameter associated with a specific port in a clustering group. User Level Admin Syntax set clustering slave-ip < IPv4 _address > port < number > [master-tcp-port <10001-65535>] [name < port_name >] [protocol telne[...]

Dynamic DNS Commands 42 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Dynamic DNS Commands Set Dynamic-DNS Set Dynamic-DNS SSL Description Configures the dynamic DNS parameters. User Level Admin Syntax set dynamic-dns [on|off] [connection-method http|http-port-824 5|https] [hostname < hostname >] [username < user name >] [pas[...]

Server Commands 43 Dynamic DNS Commands country A two character count ry code; for example, US. This fi eld is case sensitive in order to successfully match the information in the peer SS L/TLS certificate. state-province Up to a 128 character entry for the s tate/pr ovince; for example, IL. This field is case sensitive in order to successfully mat[...]

Dynamic DNS Commands 44 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set Dynamic-DNS SSL Cipher-Suite Description Sets the SSL/TLS cipher suite parameters for the connection between the IOLAN and the DNS server . User Level Admin Syntax set dynamic-dns ssl cipher-su ite option1|option2|option3|option4|optio n5 encryption any|aes|3des|de[...]

Server Commands 45 PCI Commands Show Dynamic-DNS PCI Commands Set PCI Card Show PCI hmac Select the key-hashing for message authenticat ion method for your encryption type: z Any z MD5 z SHA1 The default is Any . Description Shows the dynamic DNS setting s. User Level Admin Syntax show dynamic-dns Description Sets the type of card in the PCI slot. [...]

PCI Commands 46 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set PCI Wireless-W AN Show Wireless-W AN Description Configures the wireless W AN parameters. User Level Admin Syntax set pci wireless-wan [access- point-name < name >] [init-string < modem_init_string >] [model sierra-wireless-aircard-881|so ny-ericsson-pc300|sier[...]

Server Commands 47 IPv6 Commands IPv6 Commands Set IPv6 Show IPv6 Description Configures the basic IPv6 settings. User Level Admin Syntax set ipv6 [dhcpv6-settings ipv 6-address on|off] [dhcp-settings network-prefix on|off] [auto-obtain-dns-ipv6 on|off] [eth1|et h2] [enable-ipv6-addressing on|off] [obtai n-using auto-ipv6|dhcpv6] Options dhcpv6-set[...]

IPv6 Commands 48 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Add Custom-IPv6 Description User Level Admin Syntax add custom-ipv6 [eth1|eth2] m ethod auto network-prefix < network_prefix > [prefix-bits <0-64> ] [router-advertisement on|off] add custom-ipv6 [eth1|eth2] method ma nual ipv6-address < ipv6_address> [prefix[...]

Server Commands 49 IPv6 Commands Set Custom-IPv6 Delete Custom-IPv6 Description Configures custom IPv6 network and IP addresses. User Level Admin Syntax set custom-ipv6 [eth1|eth2] < config_ip v6_address> method auto network-prefix < network_prefix > [prefix-bits <0-64> ] [router-advertisement on|off] set custom-ipv6 [eth1|eth2] &[...]

IPv6 Router Advertise ments 50 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 IPv6 Router Advertisement s Set IPv6-Router -Advertisement Show IPv6-Router-Advertisement Description Configures IPv6 rout er advertisements. User Level Admin Syntax set ipv6-router-advertisement [eth1|eth2] on|off [dhcpv6 off|on] [dhcpv6-cfg-options off|on] Opt[...]

IOLAN SDS/SCS/STS/MD C CLI Reference Guide, V ersion 3.7 51 User Commands Chapter 3 3 This chapter defines all the CLI commands avai lable to users who are logged into the IOLAN. Commands for Users Logged Into the IOLAN Admin Help Kill Line Kill Session Logout Description Changes a Normal-level user to the Admin user . When you press Enter after yo[...]

Commands for Users Logged Into the IOLAN 52 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Menu Ping Resume Rlogin Screen Description Switches from a command line based interface to Menu mode of operation. User Level Restricted, Normal, Admin Syntax menu Description This command checks to see if a given hos t is reachable via an IP messag[...]

User Commands 53 Commands for Users Logged Into the IOLAN Set T ermtype Set User Description Sets the type of terminal bei ng used for the current session. User Level Normal, Admin Syntax set termtype wyse60|vt100|ansi|dumb|tvi925|ibm3151t e|vt320|hp700|term1|term2| term3 Option wyse60|vt100|ansi|dumb|tvi925|ibm31 51te|vt320|hp700|t erm1|term2|term[...]

Commands for Users Logged Into the IOLAN 54 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set User Session rou ti n g Determines the ro uting mode used for RIP p a ckets on the PPP and SLIP interfaces for this user . V alues are: z None —RIP packets are neither received nor sent by the IOLAN. z Send —RIP packets can o nly be sent by [...]

User Commands 55 Commands for Users Logged Into the IOLAN Show Line Users SSH Description Shows the users who are on the line. User Level Admin Syntax show line users Description St arts an SSH session to th e specified host/IP address. User Level Normal, Admin Syntax ssh < hostname/IP_address > [< T CP_port >] [termtype < terminal_n[...]

Commands for Users Logged Into the IOLAN 56 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Syslog Console Show Sessions Show T ermtype Star t ssh-2-cipher -list Select the order of negotiation for the encrypt ion method (ciphers) that the IOLAN will use for the SSH version 2 connection: z 3DES z Blowfish z AES z Arcfour z CAST user The na[...]

User Commands 57 Commands for Users Logged Into the IOLAN Te l n e t Description Starts a telnet session to the specified host/IP address. User Level Normal, Admin Syntax telnet < hostname/IP_address > [< TCP_por t >] [termtype < terminal_name >] [line-mode on|off] [map-cr-crlf on|off] [local-echo on|off] [echo <00-7f>] [eof[...]

Configuring Users 58 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Ve r s i o n Configuring Users Add User Delete User escape Defines the escape character . Returns you to the command line mode. This value is in hexadecimal with a default value of 1d (ASCII value GS ). Description Displays firmware version and build . User Level Normal, [...]

User Commands 59 Configu ring Users Set Default User Description Configures the Default User . When adding a new user , the profile of the default user will be used to assign th e values of the va rious parameters of the new user . For example if you set the service parameter of the default user to ppp , when a new user is added, their service para[...]

Configuring Users 60 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 framed-mtu Used for User Service PPP or SLIP , specifies the maximum size of packets, in bytes, being transferred across the link. On noisy links it might be preferable to fragment lar ge packets being transferred over the link, since there will be quicker r eco very from[...]

User Commands 61 Configu ring Users level The access that a user is allowed: z Admin —The admin level user has total access to the IOLAN. Y ou can create more than one admin user account but we recomm end t hat you only ha ve one. They can monitor and configure t he IOLAN. z Normal —The Normal level user has limite d access to the IOL AN. Limit[...]

Configuring Users 62 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set User sess-timer The amount of time, in seconds, that the Session Timer will run. Use t his timer to forcibly close a user ’ s sess ion (connection). When the Session Timer expires, the IOLAN will end the connection. The default value is 0 (zero), meaning that the se[...]

User Commands 63 Configu ring Users framed-compression Used for User Service PPP or SLIP , determines whether V an Jacobsen Compression is used on the link. VJ compression is a mean s of reducing the standard TCP/IP header from 40 octets to approximately 5 octets. This gi ves a significant performance improvement, particularly when interactive appl[...]

Configuring Users 64 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 hotkey-pre fix The prefix that a user types to control the current session. The default value is hex 01 , which corresponds to Ctrl-a ( ^a ) (hex value 02 would be Ctrl-b (^b), etc. ): z ^a number —T o switch from one session to another, press ^a and then the required s[...]

User Commands 65 Configu ring Users netmask This is used for the PPP or SLIP Service type s. Only used for IPv4. If the remote user is on a sub net , e nter the network’ s subnet mask. For example, a subnet mask of 255.255.0.0. password The password the user will need to enter to login to the IOLAN. This case-sensitive field accepts a maximu m of[...]

Configuring Users 66 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set User Session Show Default User Show User Description Configures a users session settings . See Set User Session on page 54 for a description of the options. User Level Admin Syntax set user .|< username >|* sessi on 1|2|3|4|* [auto on|off] [type off|telnet|rlogi[...]

IOLAN SDS/SCS/STS/MD C CLI Reference Guide, V ersion 3.7 67 Line Commands Chapter 4 4 This chapter defines all the CLI commands associat ed with configuring the IOLAN ’ s l ine parameters. 1-Port vs. 2-Port+ Line Commands If you are using a 1-port IOLAN, the admin user doe s not have the option of using the number or all (*) options in the line c[...]

Line Commands 68 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 connection-method Determines how a modem will wo rk on the line. Select from the following options: z Direct Connect —Indicates that the re is not a modem on the l ine. This is the default. z Dial In —Specify this option when a user is remote and wil l be dialing in via m[...]

Line Commands 69 Line Commands break Specifies how a break is interpreted: z off —The IOLAN ignores the break key completely and it is not passed through to the host. This is the default setting. z local —The IOLAN deals with the break locally . If the user is in a session, the break key has the same effect as a hot key . z rem ot e —When the[...]

Line Commands 70 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 keepalive Enables a per -connection TCP keepalive f eature. After the configured number of seconds, the connection will send a gratuit ous ACK to the network peer , thus either ensuring the connection stays active OR cau sing a dro pped connection condition to be recognized. [...]

Line Commands 71 Line Commands stop-bits Specifies the number of stop bits that follow a byte. The 1.5 opt ion is only available on the 1-port and 2-port models, but not on the m odem of the SDS1M or SDS3M models. term-type Specifies the type of term inal connected to the line: z Dumb z WYSE60 z VT100 z ANSI z TVI925 z IBM3151 TE z VT320 (specifica[...]

Line Commands 72 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set Line Interface The SCS, STS, and MDC IOLAN mo dels support the EIA-232 interf ace only . Therefor e, you do not need to specify interface eia-232 in the command syntax; you only need to specify the command options (e.g., monitor-dcd ). Description Configures line interfac[...]

Line Commands 73 Line Commands Set Line Service tx-driver-contr ol Used with a EIA-485 serial interface, if y our applica t ion supports RTS (Request T o Send), select this optio n. Otherwise, select Auto . Default is Auto . duplex Specify whether the line is Full Duplex (communication both ways at t he same time) or Half Duplex (communication in o[...]

Line Commands 74 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Syntax set line .|< number >|* service bidir < config_host > < server_port > < host_port > set line .|< number >|* service direct| silent rlogin < config_host > set line .|< number >|* service direct raw < config_host > < hos[...]

Line Commands 75 Line Commands rlogin Sets the line for a remote login connection. raw Creates a connection where no authentication takes place and data is passed unchanged. telnet Sets the line for a telnet connection. ssh Sets the line for an SSH connection. reverse Enables a TCP/IP host to establish a login connection on an exte rnal machine att[...]

Line Commands 76 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set Modem Set T ermtype client-initiated When this option is turned on, the IOLAN will wait for a connection from th e T ruePo rt host (see the TruePort documentation for in formation on how to set up this feature on the T ruePort host). When this option is turned off, the IO[...]

Line Commands 77 Line Commands Show Line Option wyse60|vt100|ansi|dumb|tvi925|ibm31 51te|vt320|hp700|t erm1|term2|term3 Specifies the type of term inal connected to the line: z Dumb z WYSE60 z VT100 z ANSI z TVI925 z IBM3151 TE z VT320 (specifically supp orting VT320-7) z HP700 (specifical ly supporting HP700/4 4) z T erm1, T erm2, T erm3 (user-def[...]

Line Service Commands 78 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Line Service Commands Set Custom-App Set Rlogin-Client Set T elnet-Client Description Y ou can create a custom application that can run on a specific se rial line in IOLAN using the Perle SDK. User Level Admin Syntax set custom-app line .|< number >|* prog ram-c[...]

Line Commands 79 Line Service Commands Set SSH-Client echo Defines the echo character . When Line Mode is On , typing the echo character echoes the text locally and sends only completed lines to the ho st. This value is in hexadecimal with a default value of 5 (ASCII value ^E ). eof Defines the end-of-file character . When Lin e Mode is On , enteri[...]

Line Service Commands 80 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 auto-login Creates an automatic SSH login, using the Name and Password values. name The user ’ s name when Auto Login is enabled. password The user ’ s password when Auto Login is enabled. ssh-1-cipher Select the encryption method (cipher) that you want to use fo [...]

Line Commands 81 Line Service Commands Set PPP Description Configures the Lines PPP settings. User Level Admin Syntax set ppp wireless-wan|line .|< number >|* [accm < 8_hex_digits >] [address-comp on|off] [auth-tmout < int eger >] [challenge-interval < integer >] [cr-ret ry < integer >] [cr-timeout < integer >] [[...]

Line Service Commands 82 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 ipaddr -neg Specifies whether or not IP address negotiatio n will take place. IP address negotiation is where the IOLAN allow s the remote end to sp ecify its IP address. The default value is Off . When On , the IP address specified by the remote en d will be used in [...]

Line Commands 83 Line Service Commands netmask The ne two rk s ub net mas k. F or ex amp le, 25 5.2 55. 0.0 . If your user is authenticated by RADIUS and the RADIUS parameter Fr amed-Netmask is set in the RADIUS file, the IOLAN will use the value in the RADIUS f ile in preference to the value configured here. password This field defines the passwor[...]

Line Service Commands 84 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 ruser This field is used to authenticate a user connect ing to this line. It is used in conjunction with the rpassword field. By specifying a name here , this line becomes dedicated to that user only . If left blank, the internal us er database will be used to authent[...]

Line Commands 85 Line Service Commands Set PPP Dynamic-DNS Set SLIP Description This option is only available when IP address negotiation ( ipaddr-neg ) is on . When enabled, the IOLAN will automatically updat e the DNS server with the specified host name and negotiated IP address for the PPP sessi on. User Level Admin Syntax set ppp line .|< nu[...]

Line Service Commands 86 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set UDP ripaddr The IPv4 address of the remote end of the SLIP link. Choose an address that is part of the same network or subnetwork as the IOLAN. If your user is authenticated by the IOLAN, this remote IP address wi ll be overridden if you have set a Framed IP Add r[...]

Line Commands 87 Line Service Commands Set Vmodem both|in|out|none The direction in which inform ation is received or relayed: z None —UDP service not enabled. z In —LAN to serial. The IOLAN will listen on p ort value configured i n the DS Port parameter for messages coming from the learned or configured port. z Out —Serial to LAN. The IOLAN [...]

Line Service Commands 88 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 failure-string String that is sent to the serial device when a connection fails. If no string i s entered, then the string NO CARRIER will be sent. host The target host name. init-string Y ou can specify additio nal vmodem commands th at will affect how vmodem starts.[...]

Line Commands 89 Line Service Commands style One of the following: z V erbose —Return codes (strings) are se nt to the connected device. z Numeric —The following characters can be sent to the connected device: 0 OK 1 CONNECTED 2 RING 3 NO CARRIER 4 ERROR 6 ITERF ACE DOWN 7 CONNECTION REFUSED 8 NO LISTNER success-string String that is sent to th[...]

Line Service Commands 90 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set Vmodem-Phone Set SSL Line Description This command associates a phone number wi th an IP address and TCP port. This enables the existing modem application to issue a dial command with a phone number . The phone number will be searched for in this table and if an e[...]

Line Commands 91 Line Service Commands type Specify whether the IOLAN will act as an SSL/TLS client or server . The default is Client . verify-peer Enable this option when you want the V alidat ion Criteria to match the Peer Certificate for authentication to pass. If you enable this option, you need to download an SSL/TLS certificate authority (CA)[...]

Line Service Commands 92 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set SSL Line Cipher-suite Description Sets the SSL/TLS cipher s u ite parameters for the line. User Level Admin Syntax set ssl line .|< number >|* cip her-suite option1|option2|option3|option4|optio n5 encryption any|aes|3des|des|arcfour|a rctwo|none min-key-siz[...]

Line Commands 93 Line Service Commands Set Modbus-Slave Line Set Modbus-Master Line Description Sets the Modbus slave pa rameters for the line. User Level Admin Syntax set modbus-slave line .|< numb er >|* [crlf on|off] [protocol rtu|ascii] [uid-range < uid_r ange >] Options crlf When Modbus/ASCII is selected, adds a CR/LF to th e end o[...]

Line Service Commands 94 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set Power-Management Line slave-ip The IP address of the TCP/Ethernet Modbus Slave. uid-range When Range Mo de is Hos t and you have sequential Modbus Slave IP addresses (for example, 10.10.10.1, 10.10 .10.2, 10.10.10.3, etc.), you can specify a UID range and the IOLA[...]

Line Commands 95 Line Service Commands Set Multihost Line Set Line Initiate-Connection Show Custom-App Show Interface Show Power-Management Description Configures multiple host s or a primary/back up host schema fo r Silent Raw , Reverse Raw , or Client-In ititated T r uePort service types (multihos t must be enabled by the line service type for th[...]

Line Service Commands 96 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Show PPP Show Rlogin-Client Show SLIP Show SSH-Client Show T elnet-Client Show Modbus Show UDP Show Vmodem Show Vmodem-Phone Description Shows the PPP line settings. User Level Admin Syntax show ppp line < number >|wirele ss-wan Description Show the rlogin-clien[...]

Line Commands 97 Modem Commands Modem Commands Add Modem Delete Modem Set Modem Show Modems Description Adds a modem. User Level Admin Syntax add modem < modem_name > < initi alization_string > Options < mo dem_name > The name of the modem. Do not use spaces. < initialization_st ring > The initialisation string of the modem;[...]

Email Commands 98 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Email Commands Set Email-Alert Line Description This command configur es email alert parameters for the line. User Level Admin Syntax set email-alert line < number > |* [from < email_addr >] [level emergency|alert|critical|e rror|warning|notice|info|debug] [mode [...]

Line Commands 99 Packet Forwarding Commands Show Email-Alert Line Packet Forwarding Commands Set Packet-Forwarding Line Description Shows how the line email alert is configured. User Level Admin Syntax show email-alert line < number > Description The Packet Forwarding feature allows you to control how the data coming from a serial device is p[...]

Packet Forwarding Commands 100 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 delay-between-messages The minimum time, in milliseconds, between mess ages that must pass before the data is forwarded by the IOLAN. The range is 0-65535. Th e default is 250 ms. custom-on-specific-events This section allows you to set a variety of packet defin[...]

Line Commands 101 Packet Forwarding Commands eof2 When enabled, creates a sequen ce of characters that must be received to define the end of the frame (if the EOF1 char acter is not immediately foll owed by the EOF2 character , the IOLAN waits for another EOF1 charact er to start the EOF1/EOF2 character sequence), which defines when the frame is re[...]

Packet Forwarding Commands 102 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Show Packet-Forwarding Line Description Shows the packet-forward ing settings for the line. User Level Admin Syntax show packet-forwarding line < number >[...]

IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 103 Network Commands Chapter 5 5 This chapter defines all the CLI commands asso ciated with co nfiguring the IOLAN’ s network parameters. SNMP Commands Add Community Add T rap Description Adds an SNMP community (version 1 and version 2). User Level Admin Syntax add community < community_n[...]

SNMP Commands 104 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Delete Community Delete T rap Set SNMP Description Deletes an SNMP community (version 1 and version 2). User Level Admin Syntax delete community < config_comm unity_number > Option < config_community_number > When you add an SNMP communi ty , it gets assigned to [...]

Network Commands 105 SNMP Commands Set SNMP V3-Security Description Configures SNMP settings for the V ers ion 3 read-write and read-only user . User Level Admin Syntax set snmp v3-security readonly [auth-algorithm md5|sha1] [privacy-algorithm des|aes] [security-level none|auth/nopriv|auth/ priv] set snmp v3-security readonly auth-pas sword|privacy[...]

TFTP Commands 106 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Show SNMP TFTP Commands Set Server TFTP Host s Commands Add Host Delete Host Description Shows SNMP settings, including communities and traps. User Level Admin Syntax show snmp Description Configures the IOLANs TFTP client settings. User Level Admin Syntax set server tftp [r[...]

Network Commands 107 DNS/WINS Commands Set Host Show Host s DNS/WINS Commands Add DNS Add WINS Description Configures a host in the IOLAN host table. User Level Admin Syntax set host < config_host > < IP_ad dress > set host < config_host > fqdn < text > Options < config_host > The name of the host. < IP_address >[...]

DNS/WINS Commands 108 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Delete DNS Delete WINS Show DNS Show Server Show WINS Description Deletes a DNS entry . User Level Admin Syntax delete dns < config_dns_addr > Option < config_dns_a ddr > Y ou can view a list of configured DNS server IP addresses to choose from by typing dele[...]

Network Commands 109 Gateway Commands Gateway Commands Add Gateway Description Adds a gateway . Y ou can configure up to twenty gateways. User Level Admin Syntax add gateway < config_host > def ault add gateway < config_host > host < dest_I P_addr > add gateway < config_host > network < dest_IPv4_addr >|< dest_IPv6_[...]

Gateway Commands 1 10 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 Delete Gateway Set Gateway Show Gateways Description Deletes a gateway . User Level Admin Syntax delete gateway < config_gatewa y_host > Option < config_gateway_host > Y ou can view the configured gateways that can be deleted by typing delete gateway ? . Descr[...]

Network Commands 1 1 1 Logging Commands Logging Commands Set Syslog Show Syslog Description Configures the system log. User Level Admin Syntax set syslog [level emergency|alert|critical|er ror|warning|notice|info|debug] [primary-host < config_host >] [secondary-host < config_h ost >] Options level Choose the event level that triggers a [...]

RIP Commands 1 12 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 RIP Commands Add RIP Delete RIP Description Adds a RIP MD5 key . After pressing Enter , you will be prompted for the MD5 key value. User Level Admin Syntax add rip md5 < integer_md5_id > < start_date > < start_time > < end_date > < end_time > Opt[...]

Network Commands 1 13 RIP Commands Set RIP Show RIP Description Configures the RIP MD5 key . After p ressing Enter , you will be prompted for the MD5 key value. User Level Admin Syntax set rip [authentication none| password|md5] [ethernet-mode none|send|listen|send-a nd-listen] set rip password set rip md5 < config_md5_id > [end < date >[...]

IPsec Commands 1 14 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 Show RIP Peers IPsec Commands Once there is an active VPN tunnel , the IOLAN expects all connections to be established through a VPN tunnel. T o allows hosts to connect outside of t he VPN tunnel, you must configure VPN exceptions, see VPN Exceptions on pa ge 121 for the co[...]

Network Commands 1 15 IPsec Commands Options authentication-method Specify the authentication metho d that will be used between VPN peers to authenticate the VPN tunnel. Data Options: z Shared Secr et —A text-based secret that is used to authenticate the IPsec tunnel (case sensitive). z RSA Signature —RSA signatures are used to au thenticate th[...]

IPsec Commands 1 16 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 remote-external-ip-address When NA T T raver sal (NA T_T) is enabled, the remote VPN’ s public external IPv4 or IPv6 address or FQDN. If you want to accept a VPN connect ion from any host/network, you can enter %any in this field. remote-host -nextwork The IPv4 or IPv6 ad[...]

Network Commands 1 17 IPv6 T unnels Show IPsec IPsec IPv6 T unnels Add IPv6tunnel email Up to a 64 character entry for an email address; for example, acct@anycompany .com. This field is case sensitive in order to succe ssfully match th e information in the remote X.509 certificate. An asteri sk (*) works as a wildcard. secret When the Authenticatio[...]

IPv6 T unnels 1 18 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 Set IPv6tunnel Show IPv6tunnel Delete IPv6tunnel Description Configures the speci fied IP v6 tunnel. User Level Admin Syntax set ipv6tunnel < config_tunnel _name > [mode manual|teredo|6to4] [gateway < interface >] [remote-host < c onfig_host >] Options mode[...]

Network Commands 1 19 L2TP/IPsec L2TP/IPsec Once L2TP/IPsec is enabled, the IOLAN expects all conn ections to be estab lished through a VPN tunnel. T o allows hosts to connect outsid e of the VPN tunnel, you must configure VPN exceptions, see VPN Exceptions on page 121 for the command syntax. Set L2TP Description User Level Admin Syntax set l2tp li[...]

L2TP/IPsec 120 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 country A two character country code; fo r example, US. This field is case sensitive in order to successfully match the information in the re mote X.509 certificate. An asterisk (*) works as a wildcard. state-province Up to a 128 character entry for the s tate/pr ovince; for ex[...]

Network Commands 121 VPN Exceptions Show L T2P VPN Exceptions VPN exceptions allows specific hosts or any host in a network to conn ect to the IOLAN outside of a VPN tunnel. Add VPN Exception Set VPN Exception authentication- type Specify the authentication method that will be used for the L2TP tunnel. Data Options: CHAP , P AP , Both Default: Both[...]

VPN Exceptions 122 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Delete VPN Exception Show VPN Exception host-ip < ipv4/ipv6_address > The IP address of the host that will comm unicate with the IOLAN outside of the VPN tunnel. Field Format: IPv4 or IPv6 address Description Deletes a VPN exception. T o see a list of configured VPN e[...]

IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 123 T i me Commands Chapter 6 6 This chapter defines all the CLI commands a ssociated with configuring the IOLAN’ s time parameters. Server Commands Set T ime Set T imezone Show Time Show T imezone Description Sets the IOLAN’ s system clock. User Level Admin Syntax set time < hh : mm [:[...]

SNTP Commands 124 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 SNTP Commands Add SNTP Delete SNTP Set SNTP Description Adds an SNTP server . User Level Admin Syntax add sntp [server-1 < config_ho st >] [server-2 < config_host >] Options server -1 The name of the primary SNTP server from the IOLAN host table. V alid with U nic[...]

T ime Commands 125 T ime/Date Setti ng Commands Show SNTP Show SNTP-Info T ime/Date Setting Commands Set Date Set Summertime server -1 The name of the primary SNTP server from the IOLAN host table. V alid with U nicast and Multicast modes, although in Multicast mode, the IOLAN will only accept broadcasts from the speci fied host SNTP server . serve[...]

T ime/Date Settin g Commands 126 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 Set Summertime Fixed Set Summertime Recurring offset The offset from UTC for your local time zone. Specify in the format of hours hh (valid -12 to +14) and minutes mm (valid 0 to 59 minutes) for the offset from UTC. Description Sets the summertime clock to star[...]

T ime Commands 127 T ime/Date Setti ng Commands Show Date Show Summertime end-time The time to end summer time and start stan dard time; uses the format hh:mm for a 24-hour clock (00 :00-23:59). end-week The week to end summer time and start standard time. Description Shows the date, according to the IOLAN system clock. User Level Normal, Admin Syn[...]

T ime/Date Settin g Commands 128 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7[...]

IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 129 Administration Commands Chapter 7 7 This chapter defines all the CLI commands associ ated with configuring the IOLAN ’ s ad ministration parameters. Bootup Commands Reboot Reset Reset Factory Save Description Reboots the IOLAN. Y ou will be prompted to save configuration to FLASH, if the[...]

TFTP File Transfer Commands 130 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set Bootup Show ARP Show Bootup TFTP File T ransfer Commands Netload Description Specifies remote the TFTP host and pathname for files to be loaded after a IOLAN reboot. User Level Admin Syntax set bootup firmware host < hos tname > [file < path_filena[...]

Administration Commands 131 TFTP File T ransfer Commands Net save configuration Specifies that you are going to download a new configuration file to the IOLAN. customlang Specifies that you are going to download a custom language file to th e IOLAN. term1|term2|term3 Y ou can create and download up to three cu stom terminal definitions to the IOLAN[...]

Custom Factory Default 132 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Custom Factory Default Netload Set < filename > The complete path and file name fo r the file you are uploading from the IOLA N (this path should be relative to the default path of your TFTP server, wh ich may or may not allow drive letters). Description T ran[...]

Administration Commands 133 Keys and Certificates Commands Keys and Certificates Commands Netload Description Loads certificates and keys into the IOLAN. User Level Admin Syntax netload https certificate|pri vate-key < hostname/IP_address > < filename > netload ldap certificate < hostname/IP_ address > < filename > netload s[...]

Keys and Certificates Commands 134 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Net save ipsec < tunnel_name > When you config ure an IPsec tunnel with an Authentication Method of RSA Signature , you need to download the RSA key from the remote VPN gateway to the IOLAN for that specific tunnel. < hostname / IP_address > Ente[...]

Administration Commands 135 MOTD Commands MOTD Commands Set MOTD Show MOTD Description Specifies the server/file that contains the mes sage of the da y (MOTD) that is displayed when users log into the IOLAN. Y ou can also retrieve the MOTD from a local file (it must already be downloaded to the IOLAN using the netload customapp-file command); to do[...]

MOTD Commands 136 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7[...]

IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 137 S t atistics Commands Chapter 8 8 This chapter defines all the CLI commands asso ciated with co nfiguring the IOLAN’ s statistics parameters. Configuration S t atistics Show Net stat Show Net st at S tatistics Description Shows currently used TCP/UDP sockets/ports. User Level Admin Synta[...]

Run-T i me S tatistics 138 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Show Modbus St atistics Show Routes Run-T ime St atistics Delete Arp Show Arp Show Serial Uptime Description Shows the Modbus statistics. User Level Admin Syntax show modbus statistics master -tcp line *|< number > show modbus statistics master-udp lin e *|<[...]

IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 139 IOLAN+ User Commands Chapter 9 9 Y ou can configure the IOLAN us ing the IOLAN+ menu. See the IOLAN+ User ’ s Guide for the command line interface and menu parameters. See IOLAN+ Interface in the IOLAN User ’ s Guide for a list of changes to the IOLAN+ menu. IOLAN+ Description Displays[...]

IOLAN+ 140 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7[...]

IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 141 I/O Commands Chapter 10 10 This chapter defines all the CLI commands associat ed with configuring the IOLAN’ s I/O parameters. Global I/O Commands Set IO UDP Description Sets the UDP settings fo r I/O unicast messages. User Level Admin Syntax set io udp [mode on|off] [broadcast-interval [...]

Set Line 142 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set IO Failsafe Set IO Modbus Set IO T emperature-Scale Set Line Set Line Service Description Sets the failsafe (watchdog) settings for I/O. User Level Admin Syntax set io failsafe [mode on|off] [timeout < seconds >] Options mode Enables/disables the Failsafe T imer . This [...]

I/O Commands 143 Set IOChannel Set IOChannel Set IOChannel Mode Set IOChannel Digit al I/O Description Sets general I/O channel set tings for the sp ecified channel, these settings are available to all channels and I/O serial pins. User Level Admin Syntax set iochannel < i/o_channel > [ mode enabled|disabled] [description < string >] Op[...]

Set IOChannel 144 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set IOChannel Digit al Input Description Sets the Digital input settings for the channel. User Level Admin Syntax set iochannel < digital_channe l > [alarm [trigger disabled|inactive-inp ut|active-input] [clear auto|manual] [email on|off] [syslog on|off] [snmp on|off]][...]

I/O Commands 145 Set IOChannel Set IOChannel Digit al Input (Serial Pins) Description Sets the Digital input settings for serial pi ns CTS, DSR, and DCD. This option is onl y available when the Line Service is set to Signal I/O . User Level Admin Syntax set iochannel cts|dsr|dcd [alarm [trigger disabled|inactive-inpu t|active-input] [clear auto|man[...]

Set IOChannel 146 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set IOChannel Digit al Output latch Latches (remembers) the activity transition ( active-to-inactive or inactive-to-active). The latched status is maintained until it is read. Once it i s read, it will revert to the current status. The default is disabled. Description Sets t[...]

I/O Commands 147 Set IOChannel Set IOChannel Digit al Output (Serial Pins) output Specify how the chan nel output will be handled: z Manual —Y ou must manually manipulate the ch annel output. z Pulse —Activates and deactivates the channel out put activity in intervals after it is manually activat ed. z Inactive-to-A ctive De lay —The channel [...]

Set IOChannel 148 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set IOChannel Relay Description Sets the Relay output channel settings. User Level Admin Syntax set iochannel < relay_number > output [pulse continuous|counted <pulse_coun t>] [active-to-inactive-delay < delay >] [inactive-to-active-delay < delay >] s[...]

I/O Commands 149 Set IOChannel Set IOChannel Analog (T rue Analog) Description Sets the Analog input channel settings. User Level Admin Syntax set iochannel < analog_channel > type cu rrent|voltage range < range_specifier > set iochannel < analog_channel > alarm [level 1|2|3|4|5 [mode on|off] [trigge r-type disabled|low|high] [tri[...]

Set IOChannel 150 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set IOChannel Analog (T emperature) trigger - level Specify the value that will trigger an ala rm, the measurement is based on the Ty p e and Range that you specify . This value must not fall within the scope of the value used to clear an alarm. clear -mode Specifies whether[...]

I/O Commands 151 Set IOChannel range Specify the temperature range that you wa nt to measure. For R TD, t he range is: z 1 (Pt100 a=385 -50 to 150C) Th is is the default. z 2 (Pt100 a=385 0 to 100C) z 3 (Pt100 a=385 0 to 200C) z 4 (Pt100 a=385 0 to 400C) z 5 (Pt100 a=385 -200 to 200C) z 6 (Pt100 a=392 -50 to 150C) z 7 (Pt100 a=392 0 to 100C) z 8 (P[...]

Set IOChannel 152 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set IOChannel IOExtension clear -mode Specifies whether an act ivated alarm must be Manually cleared, or can be cleared when the input drops below th e specified value (when Tr i g g e r Ty p e is High ) or goes above the specified value (when Tr i g g e r Ty p e is Low ). c[...]

I/O Commands 153 Set IOChannel enabled When enabled, the di gital input channel o r DSR/DCD/CTS input serial signal pins can be connected to: z A Digital output or relay (if the I/O model suppo rts relay) channel on the same IOLAN z Output Serial Si gnal Pins (DTR/R TS) z A Digital output channel on anot her IOLAN(s) or output serial signal pins (D[...]

Set IOChannel 154 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set IOChannel Multihost server -initiated tcp-port The TCP Port that the channe l/serial signal pin will use to communicate to another IOLAN or a TCP/ IP application. Default: 2000 for channel 1, then increments by one for each channel server -initiated mult ihost all|backup[...]

I/O Commands 155 Set IOChannel Set IOChannel IOExtension SSL Show IOChannel S t atus Kill IOChannel Description Configures the secure SSL/ TLS connection between the Digital/Relay I/O channel or serial signal pin and the host/IOLAN. For an explanation of the parameters, see Set SSL Line on page 90 . User Level Admin Syntax set iochannel < channe[...]

I/O Channel Control Commands 156 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Show IO Show IOChannel I/O Channel Control Commands The I/O commands in this section are used to manual ly manage the I/O channels. Digit al Output Description Shows global I/O information (for example, UDP , TruePort, Modbus). T emperature I/O is Analog. User[...]

I/O Commands 157 Calibrating Analog I nput (Analog/T empera ture) Digit al Input Relay Analog Input Calibrating Analog Input (Analog/T emperature) Calibrate Analog Reset Calibration Description Manages the Digital input channe l status. User Level Admin Syntax iochannel d1|d2|d3|d4|rts|dtr output activate|deactivate Option output Manually activates[...]

Calibrating Analog I nput (Analog/T empera ture) 158 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7[...]

IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 159 Power Commands Chapter 11 11 This chapter defines all the CLI commands a ssociated with configuring the IOLAN’ s power parameters. Power Commands Description Actively controls the RPS plug power . User Level Admin, Normal Syntax power cycle line < number > [pl ug < number | rang[...]

Power Commands 160 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7[...]

IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 161 Glossary This chapter provides definitions for IOLAN terms. BOOTP (BOOT strap Protocol) An Internet protocol that enables a diskless workstation to discover its own IP address, the IP address of a BOOTP server on the network, and a file to be loaded into memory to boot the machine. This en[...]

162 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 P AP (Password Authentication Protocol) Standard authentication protocol for PPP connections. see CHAP RADIUS (Remote Authentication Dial In Users Services) An open standard network securit y server that communicates wi th the P AP protocol. Reverse Connection Connections that originat e [...]