Paradyne 12000E Bedienungsanleitung

IPD1-A2-GZ40-10 July 2005 1 12000E IP Br oadband Loop Carrier Installation Instructions Document Number IPD1-A2-GZ40-10 Ju ly 2005 Contents Softwar e and Firmware License Ag reement .......... ................ ............. ............... 1 Introductio n ............ ................ ............. ................ ............. ............. .....[...]

2 July 2005 IPD1-A2-GZ40-10 e xecuted a separ ate wr itten agreem ent cov ering the Software supplied to you under this purchase , such separate written agr eement shall gov er n. P aradyne Corporation (“P aradyne”) g rants to y ou, and y ou (“Licensee”) ag ree to accept a personal, non-t ransf erable , non-exclusiv e, right (without the ri[...]

IPD1-A2-GZ40-10 July 2005 3 9. Upon such termination, the Licensee shal l refrain from an y fur ther use of the Softwar e and destro y the original and all copies of the Softw are in the possession of L icensee togethe r with all documentat ion and relate d materials. 10. This Agreement shall be gov er ned by the la ws of the State of Florida, with[...]

4 July 2005 IPD1-A2-GZ40-10 If there is visib le damage, do not attempt to conne ct the de vice. Contact y our sales representat ive . Installation Options The 12000E BL C is designed f or installation in a Restricted Access area where admittance is limited t o trained and author ized se r vice personel. It m a y be installed on a tab letop or in a[...]

IPD1-A2-GZ40-10 July 2005 5 Installing in a Rack Procedur e 1. Using a Phillips screwdriv er , attach the two provided r ac k mo unt brac kets to the sides of the 1200 0E with eight of the ten pr ovided br acket scr ews . There are se ven position options f or the rac k brac kets; position them as best suited to the space av ailable fo r your chass[...]

6 July 2005 IPD1-A2-GZ40-10 2. Mount the chassis onto the r ac k and secure the rac k mount brac kets to the sides of the rack using one of the two provided set s of eight rac k screws (whichev er size fits the rack being utiliz ed). 3. Check the ra ck f or stability , ensur ing that installation of the 12000E has not caused the rac k to become top[...]

IPD1-A2-GZ40-10 July 2005 7 Procedur e 1. Select a slot f or installation. The 12000E is a f our teen slot chassis: slots 1–12 are reserved f or interf ace modules and slots U1–U2 are rese r ved f or management modules . Although the 12000E is shipped with P ort U1 open, yo ur management module can be inst alled in either P or t U1 or P or t U2[...]

8 July 2005 IPD1-A2-GZ40-10 2. With the manageme nt module printed circu it board (PCB) f acing right and the management mo dule model name upright, align the upper and lo wer edges of the PCB with the slot module guides . 3. Slide the management mo dule firmly into the chassis . Tighten the fasten ing screw s on the mana gement module f aceplate .[...]

IPD1-A2-GZ40-10 July 2005 9 Installing Y our Interface Module(s) Interf ace modules prov ide the subscriber connections f or an 12000E; up to twelv e interf ace modules may b e installed in the 1200 0E (slots 1–12). There ar e a va riety of models a va ilable f or purchase; contact y our sales representativ e f or fur ther inf or mation or visit [...]

10 July 2005 IPD1-A2-GZ40-10 3. Slide the interf ace module firmly into the chassis . Tighten the f astening scre ws on the interface module f aceplate. F astening Screws[...]

IPD1-A2-GZ40-10 July 2005 11 P owering Up Y our 12000E CA UTION: T ur n your DC po wer source(s) OF F until y ou hav e completed connection of the 12000E as outlined in the f ollowing sections . Do not opera te the 12000E withou t a ground conn ection. Procedur e 1. Connect a ground wire to the 12000E: Line up the 2 -hole terminal lug of your groun[...]

12 July 2005 IPD1-A2-GZ40-10 3. Select a terminal bloc k. Either ter minal bloc k on the back of the 12000E ma y be used to power the chassis; only one te rm inal bloc k is required f o r operat ional purposes. The two terminal b locks on the 12000E are independent f eeds. Chassis pow er is supplied by only one terminal bl ock at a time ; the secon[...]

IPD1-A2-GZ40-10 July 2005 13 4. Using a Phillips screwdriv er , remov e th e left-hand screw from the chosen terminal bloc k (labeled "+" on the chassis). Slide the ring terminal of your positiv e power lea d around the sh aft of the scre w and insert the scre w into the same "+" terminal from which it was remov ed. 5. Remov e t[...]

14 July 2005 IPD1-A2-GZ40-10 7. V er ify the connection. T ur n your po wer source(s) on. The PWR (po wer) LED on the interf ace module and management module f a ceplates will illuminate solid green to indicate the m odules are receiving po wer . Establishing Y our Uplink Connections No configuratio n is necessary for Uplink Interf ace Modules (UIM[...]

IPD1-A2-GZ40-10 July 2005 15 Connecting Y our Subscriber Lines No configuration is necessary f or the interf ace module(s) installed in y our 12000E to operate at def ault settings . How ev e r , if you wish to run y our subscriber connections at se ttings other than the de f aults, co nfigure the interf ace module(s) prior to connection. Ref er to[...]

16 July 2005 IPD1-A2-GZ40-10 2. Detach the hook-an d-loop f astener strap fr om the f emale RJ21 connector port: lift the hook -and-loo p fastener tab on the le ft and pull t he strap open towards the r ight, leaving it loop ed under th e r ight side o f the conn ector frame. 3. Slide the male RJ21 connector of y our interf ace cable un derneath th[...]

IPD1-A2-GZ40-10 July 2005 17 5. V er ify the connection(s). The LK (Link) LED f or each por t being connected with a remote modem will illuminate solid or flashing green (depending on the interf ace module model) to indicate a connection has be en established . Link up time betw een interf ace modules and remote mod ems can va r y from one to fiv e[...]

18 July 2005 IPD1-A2-GZ40-10 Conf iguration and Management Although no configu ration is necessary to run subscriber lines at the defa ult settings , all 12000E parameter settings are software se lectab le via Command Line Interf ace (CLI), Simple Network Management Prot ocol (SNMP), or the Netw ork Management System (NMS), depending upon the capab[...]

IPD1-A2-GZ40-10 July 2005 19 F an Module The 12000E f an module is installed horizontally abo ve the interf ace module slots. It comes pre-installed an d should not be remo ved unless it is being replaced. F an functionality is indicated b y a F AN LED on the management module ( all models): no illumination or solid green illumina tion indicates al[...]

20 July 2005 IPD1-A2-GZ40-10 Specif ications T able 1. Specifications Specif ication Criteria Environment Operatin g T emperature: –40° F to 149° F (–40° C to 65° C) Storage T emperature: –40° F to 158° F (–40° C to 70° C) Humidity: 5 % to 95 %, non-condensing Altitude: –200 ft to 16,500 ft (–60 m to 5,000 m) Physical 15.75"[...]

IPD1-A2-GZ40-10 July 2005 21 Important Safety Instructions 1. Read and f ollow all warning notices an d instructions marked on the produ ct or included in the man ual. 2. Do not attempt to ser vice this product y ourself, as opening or remo ving cov ers ma y expose you to dangerous hig h voltage points or o ther r isks. Ref er all ser vicing to qua[...]

22 July 2005 IPD1-A2-GZ40-10 12. In addition, if the equipment is to be used with telecommuni cations circuits , take the f ollowing precautions: — Ne v er install telephone wiring during a lightning storm. — Nev er install telephone jacks in wet lo cations unless the jack is specifically designed f or wet locations . — Ne v er touch uninsula[...]

IPD1-A2-GZ40-10 July 2005 23 CANAD A – EMI NO TICE: ! This Class A digi tal apparatus meet s all requirements of the Canadian interferen ce-causing equipment regula tions. Cet appareil n umérique de la c lasse A respecte toutes les e xig ences du règlement sur le matérial br ouilleur du Canada. W arranty , Sales, Service, and T raining Informa[...]

24 July 2005 IPD1-A2-GZ40-10 *IPD1-A2-GZ40-10* *IPD1-A2-GZ40-10*[...]