Lenovo 7387 Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222

Zur Seite of

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Lenovo 7387 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Lenovo 7387, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Lenovo 7387 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Lenovo 7387. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Lenovo 7387 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Lenovo 7387
- Den Namen des Produzenten und das Produktionsjahr des Geräts Lenovo 7387
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Lenovo 7387
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Lenovo 7387 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Lenovo 7387 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Lenovo finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Lenovo 7387 zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Lenovo 7387, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Lenovo 7387 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    Hardw are Maintenance Manual Leno v o 3000 J Series T ypes 7387, 7388, 7389, 7390, 7391, 7392, 7393, 7394, 7395, 7396, 7397, 7398[...]

  • Seite 2

    [...]

  • Seite 3

    Le n o v o 3 000 J Ser ie s[...]

  • Seite 4

    Note: Before using this information and the pr oduct it supports, be sure to r ead the information under “Notices,” on page 213. Ninth Edition (March 2008) © Copyright Lenovo 2006, 2008. Portions © Copyright International Business Machines Corporation 2005. All rights reserved. LENOVO products, data, computer softwar e, and services have been[...]

  • Seite 5

    Contents Chapter 1. About this manual . . . . .1 Important Safety Information . . . . . . . . .1 Important information about replacing RoHS compliant FRUs . . . . . . . . . . . . .2 Chapter 2. Safety information . . . . .3 General safety . . . . . . . . . . . . . .3 Electrical safety . . . . . . . . . . . . .3 Safety inspection guide . . . . . . . [...]

  • Seite 6

    Replacing the system board (T ypes 7390, 7391, and 7392) . . . . . . . . . . . . . . . . 129 Replacing the micropr ocessor (T ypes 7396, 7397, and 7398) . . . . . . . . . . . . . . . 132 Replacing the micropr ocessor (T ypes 7390, 7391, and 7392) . . . . . . . . . . . . . . . 136 Replacing the hard disk drive . . . . . . . . 140 Replacing an optica[...]

  • Seite 7

    Chapter 1. About this manual This manual contains service and refer ence information for Lenovo ® computers listed on the cover . It is intended only for trained servicers who are familiar with Lenovo computer products. Before servicing a Lenovo pr oduct, be sure to r ead the Safety Information. See Chapter 2, “Safety information,” on page 3. [...]

  • Seite 8

    Important information about replacing RoHS compliant FRUs RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry . RoHS requirements must be implemented on Lenovo products placed on the market after June 2006. Product[...]

  • Seite 9

    Chapter 2. Safety information This chapter contains the safety information that you need to be familiar with before servicing a computer . General safety Follow these rules to ensur e general safety: v Observe good housekeeping in the area of the machines during and after maintenance. v When lifting any heavy object: 1. Ensure you can stand safely [...]

  • Seite 10

    CAUTION: Electrical current from power , telephone, and communication cables can be hazardous. To avoid personal injury or equipment damage, disconnect the attached power cords, telecommunication systems, networks, and modems before you open the server/workstation covers, unless instructed otherwise in the installation and configuration procedures.[...]

  • Seite 11

    v Always look carefully for possible hazards in your work ar ea. Examples of these hazards ar e moist floors, nongrounded power extension cables, power sur ges, and missing safety grounds. v Do not touch live electrical circuits with the reflective surface of a plastic dental mirror . The surface is conductive; such touching can cause personal inju[...]

  • Seite 12

    5. Check for any obvious alterations. Use good judgment as to the safety of any alterations. 6. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage. 7. Check for worn, frayed, or pinched cables. 8. Check that the power-supply cover fasteners (screws [...]

  • Seite 13

    Safety notices (multi-lingual translations) The caution and danger safety notices in this section are pr ovided in the following languages: v English v Arabic v Brazilian/Portuguese v Chinese (simplified) v Chinese (traditional) v French v German v Hebrew v Italian v Korean v Spanish DANGER Electrical current fr om power , telephone and communicati[...]

  • Seite 14

    CAUTION: When replacing the lithium battery , use only Part Number 33F8354 or an equivalent type battery recommended by the manufacturer . If your system has a module containing a lithium battery , replace it only with the same module type made by the same manufacturer . The battery contains lithium and can explode if not properly used, handled, or[...]

  • Seite 15

    CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source. 1 2 Chapter 2. Safety infor[...]

  • Seite 16

    10 Lenovo 3000 J Series[...]

  • Seite 17

    Chapter 2. Safety information 11[...]

  • Seite 18

    ≥ 18 kg (37 lbs) ≥ 32 kg (70.5 lbs) ≥ 55 kg (121.2 lbs) 1 2 12 Lenovo 3000 J Series[...]

  • Seite 19

    PERIGO A corrente elétrica pr oveniente de cabos de alimentação, de telefone e de comunicações é perigosa. Para evitar risco de choque elétrico: v Não conecte nem desconecte nenhum cabo ou execute instalação, manutenção ou reconfiguração deste pr oduto durante uma tempestade com raios. v Conecte todos os cabos de alimentação a tomad[...]

  • Seite 20

    CUIDADO: Ao substituir a bateria de lítio, utilize apenas uma bateria com Número de Peça 33F8354 ou um tipo de bateria equivalente recomendado pelo Se o seu sistema possui um módulo com uma bateria de lítio, substitua-o apenas por um módulo do mesmo tipo e do mesmo fabricante. A bateria contém lítio e pode explodir se não for utilizada, ma[...]

  • Seite 21

    CUIDADO: O botão de controle de alimentação do dispositivo e o botão para ligar/desligar da fonte de alimentação não desligam a corrente elétrica fornecida ao dispositivo. O dispositivo também pode ter mais de um cabo de alimentação. Para remover toda a corrente elétrica do dispositivo, assegur e que todos os cabos de alimentação este[...]

  • Seite 22

    16 Lenovo 3000 J Series[...]

  • Seite 23

    1 2 Chapter 2. Safety information 17[...]

  • Seite 24

    18 Lenovo 3000 J Series[...]

  • Seite 25

    1 2 Chapter 2. Safety information 19[...]

  • Seite 26

    DANGER Le courant électrique provenant de l’alimentation, du téléphone et des câbles de transmission peut présenter un danger . Pour éviter tout risque de choc électrique : v Ne manipulez aucun câble et n’effectuez aucune opération d’installation, d’entretien ou de r econfiguration de ce produit au cours d’un orage. v Branchez to[...]

  • Seite 27

    A TTENTION: Remplacer la pile au lithium usagée par une pile de référence identique exclusivement, (référence 33F8354), ou suivre les instructions du fabricant qui en définit les équivalences. Si votre système est doté d’un module contenant une pile au lithium, vous devez le remplacer uniquement par un module identique, produit par le m?[...]

  • Seite 28

    ≥ 18 kg (37 lbs) ≥ 32 kg (70.5 lbs) ≥ 55 kg (121.2 lbs) A TTENTION: Soulevez la machine avec précaution. A TTENTION: L’interrupteur de contrôle d’alimentation de l’unité et l’interrupteur dubloc d’alimentation ne coupent pas le courant électrique alimentantl’unité. En outre, le système peut être équipé de plusieurs cordon[...]

  • Seite 29

    VORSICHT An Netz-, T elefon- und Datenleitungen können gefährliche Spannungen anliegen. Aus Sicherheitsgründen: v Bei Gewitter an diesem Gerät keine Kabel anschließen oder lösen. Ferner keine Installations-, W artungs- oder Rekonfigurationsarbeiten durchführen. v Gerät nur an eine Schutzkontaktsteckdose mit ordnungsgemäß geerdetem Schutzk[...]

  • Seite 30

    CAUTION: Eine verbrauchte Lithiumbatterie nur durch eine Batterie mit der T eilenummer 33F8354 oder eine gleichwertige, vom Hersteller empfohlene Batterie ersetzen. Enthält das System ein Modul mit einer Lithiumbatterie, dieses nur durch ein Modul desselben T yps und von demselben Hersteller ersetzen. Die Batterie enthält Lithium und kann bei uns[...]

  • Seite 31

    ≥ 18 kg ≥ 32 kg ≥ 55 kg ACHTUNG: Arbeitsschutzrichtlinien beim Anheben der Maschine beachten. ACHTUNG: Mit dem Netzschalter an der Einheit und am Netzteil wird die Stromversorgung für die Einheit nicht unterbrochen. Die Einheit kann auch mit mehreren Netzkabeln ausgestattet sein. Um die Stromversorgung für die Einheit vollständig zu unterb[...]

  • Seite 32

    26 Lenovo 3000 J Series[...]

  • Seite 33

    Chapter 2. Safety information 27[...]

  • Seite 34

    1 2 28 Lenovo 3000 J Series[...]

  • Seite 35

    PERICOLO La corrente elettrica pr oveniente dai cavi di alimentazione, del telefono e di comunicazione può essere pericolosa. Per evitare il rischio di scosse elettriche: v Non collegare o scollegare qualsiasi cavo oppure effettuare l’installazione, la manutenzione o la riconfigurazione del prodotto durante un temporale. v Collegare tutti i fili[...]

  • Seite 36

    A TTENZIONE: Quando si sostituisce la batteria al litio, utilizzare solo il Numero parte 33F8354 o un tipo di batteria equivalente consigliato dal produttore. Se sul sistema è presente un modulo che contiene una batteria al litio, sostituirlo solo con un tipo di modulo dello stesso tipo della stessa casa di produzione. La batteria contiene litio e[...]

  • Seite 37

    ≥ 18 kg ≥ 32 kg ≥ 55 kg A TTENZIONE: Prestare attenzione nel sollevare l’apparecchiatura. A TTENZIONE: Il pulsante di controllo dell’alimentazione presente sull’unità e l’interruttore dell’alimentatore non disattivano l’alimentazione corrente fornita all’unità. E’ possibile che l’unità disponga di più cavi di alimentazio[...]

  • Seite 38

    32 Lenovo 3000 J Series[...]

  • Seite 39

    1 2 Chapter 2. Safety information 33[...]

  • Seite 40

    PELIGRO La corriente eléctrica procedente de cables de alimentación, teléfonos y cables de comunicación puede ser peligrosa. Para evitar el riesgo de descarga eléctrica: v No conecte ni desconecte los cables ni realice ninguna tarea de instalación, mantenimiento o reconfiguración de este producto durante una tormenta eléctrica. v Conecte to[...]

  • Seite 41

    PRECAUCIÓN: Cuando sustituya una batería de litio, utilice solamente una batería número de pieza 33F8354 u otra de tipo equivalente recomendada por el fabricante. Si su sistema dispone de un módulo que contiene una batería de litio, reemplácelo sólo con el mismo tipo de módulo, del mismo fabricante. La batería contiene litio y puede explo[...]

  • Seite 42

    ≥ 18 kg ≥ 32 kg ≥ 55 kg PRECAUCIÓN: Adopte procedimientos seguros al levantar el equipo. PRECAUCIÓN: El botón de control de alimentación del dispositivo y el interruptor de alimentación de la fuente de alimentación no desconectan la corriente eléctrica suministrada al dispositivo. Además, el dispositivo podría tener más de un cable [...]

  • Seite 43

    Chapter 3. General information This chapter provides general information that applies to all machine types supported by this publication. The Lenovo Care program Use the Lenovo Care pr ogram for general information about the use, operation, and maintenance of the computer . The Lenovo Care program also contains information to help solve problems an[...]

  • Seite 44

    Specifications This section lists the physical specifications for the computer . Machine types 7387, 7388, 7389, 7393, 7394, and 7395 Dimensions W idth: 180 mm (7.09 in.) Height: 392 mm (15.43 in.) Depth: 445 mm (17.52 in.) W eight Minimum configuration as shipped: 9.1kg (20.06 lbs) Maximum configuration: 10.2 kg (22.5 lbs) Environment Air temperat[...]

  • Seite 45

    Machine types 7390, 7391, 7392, 7396, 7397, and 7398 This section lists the physical specifications for the computer . Dimensions W idth: 331 mm (13.0 in.) Height: 108 mm (4.3 in.) Depth: 405 mm (15.9 in.) W eight Minimum configuration as shipped: 8.2 kg (18.0 lbs) Maximum configuration: 8.3 kg (18.2 lbs) Environment Air temperature: Operating at 0[...]

  • Seite 46

    40 Lenovo 3000 J Series[...]

  • Seite 47

    Chapter 4. General Checkout Attention The drives in the computer you are servicing might have been r earranged or the drive startup sequence changed. Be extremely car eful during write operations such as copying, saving, or formatting. Data or programs can be overwritten if you select an incorrect drive. General error messages appear if a pr oblem [...]

  • Seite 48

    – What, when, where, single, or multiple systems? – Is the failure repeatable? – Has this configuration ever worked? – If it has been working, what changes were made prior to it failing? – Is this the original reported failure? v Diagnostics version – T ype and version level v Hardware configuration – Print (print screen) configuratio[...]

  • Seite 49

    Chapter 5. Diagnostics Diagnostic programs ar e used to test hardwar e components of the computer and report operating-system-contr olled settings that can cause hardwar e failures. Ther e are two diagnostic pr ograms preinstalled on the computer to help diagnose problems: v PC-Doctor for W indows ® (used when diagnosing problems while running the[...]

  • Seite 50

    Note: It is important to cr eate a diagnostic CD image or diagnostic diskettes in case PC-Doctor for DOS cannot be run from the Rescue and Recovery workspace. Creating a diagnostic CD image To create a diagnostic CD image, download a self-starting bootable CD image (known as an .iso image) of the diagnostic program fr om http:// www .lenovo.com/sup[...]

  • Seite 51

    Note: If you ar e running diagnostics from a diskette, when pr ompted, remove the first diskette and insert the second diskette. 5. Select the diagnostic test you want to run. Press the F1 key for additional help. 6. Remove the CD or diskette when the program finishes. Running diagnostics from the Rescue and Recovery workspace If you do not have a [...]

  • Seite 52

    Navigating through the diagnostics programs Use the cursor movement keys to navigate within the menus. v The Enter key is used to select a menu item. v The Esc key is used to back up to the previous menu. v For online help select F1 . Running tests There ar e four ways to run the diagnostic tests. v Using the cursor movement keys, highlight Run Nor[...]

  • Seite 53

    Contains the date when the diagnostic test was run. The date is retrieved fr om CMOS and displayed using the YYYYMMDD format. v ChkDigits: Contains a 2-digit check-digit value to ensure the following: – Diagnostics were run on the specified date. – Diagnostics were run on the specified computer . – The diagnostic error code is recor ded corre[...]

  • Seite 54

    v Write-Splice Repair - detects and corrects Err or Correction Code err ors during V erify tests. v Auto Spin Down - a gradual spin down of the drive platters to avoid damaging the media. v Manufacturer Log - an in-depth manufacturer supported log of err ors on the drive. Multitasking: To allow simultaneous testing of multiple hard drives whenever [...]

  • Seite 55

    v Destroys all copies of the FAT T able on all partitions (both the master and backup). v Destroys the partition table. v Provides messages that warn the user that this is a non-recoverable pr ocess. The Full Erase Hard Drive pr ovides a DOS utility that performs the following: v Performs all the steps in Quick Erase. v Provides a DOS utility that [...]

  • Seite 56

    50 Lenovo 3000 J Series[...]

  • Seite 57

    Chapter 6. Using the Setup Utility The Setup Utility program is stor ed in the electrically erasable programmable read-only memory (EEPROM) of the computer . The Setup Utility program is used to view and change the configuration settings of the computer , regardless of which operating system you are using. However , the operating-system settings mi[...]

  • Seite 58

    1. Start the Setup Utility program (see “Starting the Setup Utility program” on page 51). 2. From the Setup Utility program menu, select Set User Password and pr ess Enter . 3. The password dialog box will be displayed. T ype the new password, and press Enter . 4. When prompted to confirm the password, type the passwor d again. If you type the [...]

  • Seite 59

    Selecting a startup device If the computer does not start up (boot) from a device such as the CD-ROM, diskette, or hard disk as expected, use one of the following pr ocedures to select a startup device. Selecting a temporary startup device Use this procedur e to startup from any boot device. Note: Not all CDs, har d disks, and diskettes are startab[...]

  • Seite 60

    54 Lenovo 3000 J Series[...]

  • Seite 61

    Chapter 7. Symptom-to-FRU Index The Symptom-to-FRU index lists error symptoms and possible causes. The most likely cause is listed first. Always begin with Chapter 4, “General Checkout,” on page 41. This index can also be used to help you decide which FRUs to have available when servicing a computer . If you are unable to correct the pr oblem u[...]

  • Seite 62

    Diagnostic error codes Refer to the following diagnostic error codes when using the diagnostic tests. See “Running tests” on page 46 for the specific type for information about the Diagnostic programs. In the following index, X can repr esent any number . Diagnostic Error Code FRU/Action 000-000-XXX BIOS T est Passed No action 000-002-XXX BIOS [...]

  • Seite 63

    Diagnostic Error Code FRU/Action 000-196-XXX BIOS test halt, error thr eshold exceeded 1. Press F3 to review the log file 2. Re-start the test to r eset the log file 000-197-XXX BIOS test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Re-run test 3. Repl[...]

  • Seite 64

    Diagnostic Error Code FRU/Action 001-032-XXX System Device Controller failur e System board 001-034-XXX System Device Buffer Allocation failur e 1. Reboot the system 2. Flash the system. See “Flash update procedur es” on page 209 3. Run memory test 4. System boar d 001-035-XXX System Device Reset condition detected System board 001-036-XXX Syst[...]

  • Seite 65

    Diagnostic Error Code FRU/Action 001-254-XXX 001-255-XXX 001-256-XXX 001-257-XXX System DMA error System board 001-260-XXX 001-264-XXX System IRQ error System board 001-268-XXX System IRQ1 failure 1. Device on IRQ1 2. System boar d 001-269-XXX System IRQ2 failure 1. Device on IRQ2 2. System boar d 001-270-XXX System IRQ3 failure 1. Device on IRQ3 2[...]

  • Seite 66

    Diagnostic Error Code FRU/Action 001-286-XXX 001-287-XXX 001-288-XXX System T imer failure System board 001-292-XXX System CMOS RAM error 1. Run Setup and re-test 2. System boar d 001-293-XXX System CMOS Battery 1. CMOS Battery 2. System boar d 001-298-XXX System RT C date/time update failure 1. Flash the system. See “Flash update procedures” o[...]

  • Seite 67

    Diagnostic Error Code FRU/Action 005-036-XXX V ideo Register error 1. V ideo card, if installed 2. System boar d 005-038-XXX System BIOS extension failure 1. V ideo card, if installed 2. System boar d 005-040-XXX V ideo IRQ failure 1. V ideo card, if installed 2. System boar d 005-195-XXX V ideo T est aborted by user Information only Re-start the t[...]

  • Seite 68

    Diagnostic Error Code FRU/Action 006-197-XXX Diskette interface test warning 1. If a component is called out, make sure it is connected and/or enabled 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 006-198-XXX Diskette interface test aborted 1. If a component is called out, make s[...]

  • Seite 69

    Diagnostic Error Code FRU/Action 01 1-197-XXX Serial port test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 01 1-198-XXX Serial port test a[...]

  • Seite 70

    Diagnostic Error Code FRU/Action 014-196-XXX Parallel port test halt, error thr eshold exceeded 1. Press F3 to review the log file 2. Re-start the test to r eset the log file 014-197-XXX Parallel port test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. R[...]

  • Seite 71

    Diagnostic Error Code FRU/Action 015-036-XXX USB port Register error System board 015-040-XXX USB port IRQ failure 1. Run setup and check for conflicts 2. Flash the system. See “Flash update procedur es” on page 209 3. System boar d 015-195-XXX USB port T est aborted by user Information only Re-start the test, if necessary 015-196-XXX USB port [...]

  • Seite 72

    Diagnostic Error Code FRU/Action 018-197-XXX PCI Card test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 018-198-XXX PCI Card test aborted 1[...]

  • Seite 73

    Diagnostic Error Code FRU/Action 020-198-XXX PCI test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Flash the system and r e-test. See “Flash update procedur es” on page 209 3. Go to “Undetermined pr oblems” on page 81 020-199-XXX PCI test faile[...]

  • Seite 74

    Diagnostic Error Code FRU/Action 025-198-XXX IDE interface test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Flash the system and r e-test. See “Flash update procedur es” on page 209 3. Go to “Undetermined pr oblems” on page 81 025-199-XXX IDE [...]

  • Seite 75

    Diagnostic Error Code FRU/Action 030-198-XXX SCSI interface test aborted 1. If a component is called out, make sure it is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Flash the system and r e-test. See “Flash update procedur es” on page 209 3. Go to “Undetermined pr oblems” on page 81 030-199-XXX SCS[...]

  • Seite 76

    Diagnostic Error Code FRU/Action 071-00X-XXX 071-01X-XXX 071-02X-XXX Audio port error 1. Run Setup 2. Flash the system. See “Flash update procedur es” on page 209 3. System boar d 071-03X-XXX Audio port failure 1. Speakers 2. Micr ophone 3. Audio car d, if installed 4. System boar d 071-04X-XXX Audio port failure 1. Run Setup 2. Audio car d, if[...]

  • Seite 77

    Diagnostic Error Code FRU/Action 080-196-XXX Game Port interface test halt, error thr eshold exceeded 1. Press F3 to review the log file 2. Re-start the test to r eset the log file 080-197-XXX Game Port interface test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on [...]

  • Seite 78

    Diagnostic Error Code FRU/Action 086-197-XXX Mouse Port interface test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 086-198-XXX Mouse Port [...]

  • Seite 79

    Diagnostic Error Code FRU/Action 170-0XX-XXX V oltage Sensor(s) failure 1. Flash system 2. System boar d 170-195-XXX V oltage Sensor(s) T est aborted by user Information only Re-start the test, if necessary 170-196-XXX V oltage Sensor(s) test halt, error thr eshold exceeded 1. Press F3 to review the log file 2. Re-start the test to r eset the log f[...]

  • Seite 80

    Diagnostic Error Code FRU/Action 175-197-XXX Thermal Sensor(s) test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6, “Using the Setup Utility,” on page 51 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 175-198-XXX Thermal Sensor[...]

  • Seite 81

    Diagnostic Error Code FRU/Action 215-000-XXX CD-ROM Drive T est Passed No action 215-XXX-XXX CD-ROM Drive error 1. CD-ROM Drive Cable 2. Check power supply voltages 3. CD-ROM drive 4. System boar d 217-000-XXX Hard Disk Drive T est Passed No action 217-25X-XXX 217-26X-XXX Hard Disk Drive (IDE) err or 1. Hard Disk Drive Cable 2. Check power supply v[...]

  • Seite 82

    Diagnostic Error Code FRU/Action 415-000-XXX Modem T est Passed No action 415-XXX-XXX Modem error Remove the Modem and re-test the system 76 Lenovo 3000 J Series[...]

  • Seite 83

    Beep symptoms Beep symptoms are tones or a series of tones separated by pauses (intervals without sound) during POST . The following table describes beep symptoms. Beep Symptom FRU/Action 2 short beeps CMOS setting error Perform the following actions in order . 1. Start the Setup Utility pr ogram and press F10 to Save and exit. See Chapter 6, “Us[...]

  • Seite 84

    POST error codes Each time you power-on the system, it performs a series of tests that check the operation of the system and some options. This series of tests is called the Power-On Self-T est , or POST . POST does the following operations. v Checks some basic system-board operations v Checks the memory operation v Starts the video operation v V e[...]

  • Seite 85

    POST Error Message Description/Action Press TA B to show POST screen Pr essing the TA B key permits the user to toggle between the default POST display screen and a custom POST display scr een. Error: Non-System disk or disk err or Replace and press any key when r eady The BIOS was unable to find a suitable boot device. Make sure the boot drive is [...]

  • Seite 86

    Miscellaneous error messages Message/Symptom FRU/Action Changing display colors Display/Monitor Computer will not power-of f. See “Power Supply Problems” on page 55. 1. Power Switch 2. System Boar d 3. Riser car d, if installed Computer will not RPL from server 1. Ensure that network is in startup sequence as first device or first device after [...]

  • Seite 87

    Message/Symptom FRU/Action Non-system disk or disk error -type message with a known-good diagnostic diskette. 1. Diskette Drive 2. System Boar d 3. Diskette Drive Cable Other display symptoms not listed above (including blank or illegible display) 1. Display 2. System Boar d Power-on indicator or har d disk drive in-use light not on, but computer w[...]

  • Seite 88

    c. Memory modules d. Extended video memory e. External Cache f. External Cache RAM g. Hard disk drive h. Diskette drive 3. Power-on the computer to re-test the system. 4. Repeat steps 1 through 3 until you find the failing device or adapter . If all devices and adapters have been removed, and the pr oblem continues, replace the system board. 82 Len[...]

  • Seite 89

    Chapter 8. Replacing FRUs (T ypes 7387, 7388, 7389, 7393, 7394, and 7395) Important Before you r eplace any FRU, read Chapter 2, “Safety information,” on page 3. These precautions and guidelines will help you work safely . FRU replacements ar e to be done by trained service technicians only . This chapter does not contain a remove and r eplace [...]

  • Seite 90

    Rear connectors The following illustration shows the locations of the connectors on the rear of the computer . 1 Power connector 9 Ethernet connector 2 V oltage selection switch (some models) 10 USB connectors 3 Mouse connector 11 Microphone connector 4 Keyboard connector 12 Audio line out connector ?[...]

  • Seite 91

    3. Disconnect all cables attached to the computer . This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer . 4. Remove the two thumb screws at the rear of the left-side cover and slide the cover to the rear to r emove. 5. If necessary , remove the right-side cover in the same manner . Chapter 8[...]

  • Seite 92

    Locations The following illustration will help you locate the major FRUs in the computer . 1 Heat sink and fan 6 Front panel car d 2 Micropr ocessor 7 Hard disk drive 3 Memory modules 8 System board 4 Optical drive 9 System fan 5 Diskette drive 10 Power supply 86 Lenovo 3000 J Series[...]

  • Seite 93

    Identifying parts on the system board There ar e differ ent system boards depending on the machine type. Machine T ypes 7387, 7388, and 7389 1 Micropr ocessor fan connector 11 Front panel (power switch/LED) connector 2 Micropr ocessor and heat sink 12 S ATA IDE connectors (2) 3 Memory connector 1 13 Front USB con[...]

  • Seite 94

    Machine T ypes 7393, 7394, and 7395 1 Micropr ocessor and heat sink 11 Front USB connectors (2) 2 Micropr ocessor fan connector 12 Serial (COM2) connector 3 Memory connector 1 13 Front audio connectors 4 Memory connector 2 14 PCI adapter connectors (2) 5 Power connector 15 PCI Express x1 g[...]

  • Seite 95

    Removing and replacing the front bezel The front bezel must be r emoved to replace some FRUs. 1. Remove both the left-side and right-side covers. See “Removing the covers” on page 84. 2. Disconnect the cable for the power switch/LED assembly from the system board. See “Identifying parts on the system boar d” on page 87 for the connector loc[...]

  • Seite 96

    Replacing a memory module 1. Remove the left-side cover . See “Removing the covers” on page 84. 2. Locate the memory connectors. See “Identifying parts on the system board” on page 87. 3. Open the retaining clips and remove the failing memory module. 4. Make sure the notch 1 on the new memory module is aligned correctly with the conne[...]

  • Seite 97

    Replacing a PCI adapter 1. Remove the left-side cover . See “Removing the covers” on page 84. 2. Remove the screw securing the adapter being replaced. 3. Pull the adapter straight out of the PCI connector . 4. Remove the new adapter from its static-protective package. 5. Install the new adapter into the appropriate PCI connector . 6. Install th[...]

  • Seite 98

    Replacing the CMOS battery If the CMOS battery fails, the date, time, and configuration information (including passwords) ar e lost. An error message is displayed when you turn on the computer . 1. Refer to “Safety notices (multi-lingual translations)” on page 7 for information about replacing and disposing of the battery . 2. T urn off the com[...]

  • Seite 99

    Replacing the power supply Attention Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, curr ent, and energy levels ar e present inside any component that has this label attached. There ar e no servicable parts inside these components. 1. Remove the left-side cover . See “Removing the co[...]

  • Seite 100

    Replacing the system board (T ypes 7393, 7394, and 7395) Note: When r eplacing the system board a new r etention module for the micropr ocessor heat sink is requir ed. Make sure you have a new r etention module before beginning this pr ocedure. 1. Remove both side covers. See “Removing the covers” on page 84. 2. Lay the computer on the right si[...]

  • Seite 101

    10. Lift the small handle 3 and open the retainer 1 . 11 . Lift the microprocessor 2 straight up and out of the system boar d socket. Notes: a. Y our micropr ocessor and socket might look differ ent than the one illustrated. b. Note the orientation of the notches on the microprocessor . This is important when reinstalling the micr[...]

  • Seite 102

    cover and place it on the micropr ocessor socket of the failing system board when you complete this pr ocedure. 13. Holding the microprocessor with your fingers, position the micr oprocessor so that the notches on the micropr ocessor are aligned with the tabs in the micropr ocessor socket on the new system board. Important To avoid damaging the mic[...]

  • Seite 103

    Replacing the system board (T ypes 7387, 7388, and 7389) 1. Remove only the left-side cover . See “Removing the covers” on page 84. 2. Lay the computer on the right side to make the system board accessible. 3. Remove any adapter cards installed in the PCI connectors. See “Replacing a PCI adapter” on page 91. 4. Carefully take note of the lo[...]

  • Seite 104

    11 . Lift the small handle 1 . 12. Lift the microprocessor 2 straight up and out of the socket. Notes: a. Y our micropr ocessor and socket might look differ ent than the one illustrated. b. Note the orientation of the microprocessor in the socket. Look for the small triangle on one corner of the micropr ocessor . This is important when [...]

  • Seite 105

    13. Holding the microprocessor with your fingers, position the micr oprocessor so that the small triangle 1 is aligned with the corresponding triangle on the socket. 14. Lower the microprocessor straight down into the socket. 15. Lower and latch the handle to secure the micropr ocessor in the socket. 16. Install the retention module that was [...]

  • Seite 106

    Replacing the microprocessor (T ypes 7393, 7394, and 7395) Note: A thermal gr ease syringe is requir ed to complete the micropr ocessor installation. Make sure the gr ease syringe is available before beginning the procedur e. The FRU number for the thermal grease is 91P8835. 1. Remove the left-side cover . See “Removing the covers” on page 84. [...]

  • Seite 107

    6. Lift the small handle 3 and open the retainer 1 . Important T ouch only the sides of the micropr ocessor . Do not touch the gold contacts on the bottom. 7. Lift the microprocessor 2 straight up and out of the socket. Chapter 8. Replacing FRUs (T ypes 7387, 7388, 7389, 7393, 7394, and 7395) 101[...]

  • Seite 108

    Notes: a. Note the orientation of the notches 1 on the microprocessor . This is important when reinstalling the micr oprocessor on the new system boar d. b. Do not drop anything onto the micropr ocessor socket while it is exposed. The socket pins must be kept as clean as possible. 8. Holding the microprocessor with your fingers, r emove the p[...]

  • Seite 109

    12. Use the thermal grease syringe to place five drops of gr ease on the top of the micropr ocessor . Each drop of grease should be 0.03ml (3 tick marks on the grease syringe). 13. Install the heat sink and fan assembly on the system board. 14. Connect the heat sink and fan assembly cable to the system board. See “Identifying parts on the system [...]

  • Seite 110

    Replacing the microprocessor (T ypes 7387, 7388, and 7389) 1. Remove the left-side cover . See “Removing the covers” on page 84. 2. Lay the computer on the right side to make the system board and micropr ocessor accessible. 3. Disconnect the heat sink and fan assembly cable from the system board. See “Identifying parts on the system board” [...]

  • Seite 111

    7. Lift the microprocessor 2 straight up and out of the socket. Notes: a. Y our micropr ocessor and socket might look differ ent than the one illustrated. b. Note the orientation of the microprocessor in the socket. Look for the small triangle on one corner of the micropr ocessor . This is important when reinstalling the micr oprocessor on th[...]

  • Seite 112

    11 . Lower the microprocessor straight down into the socket. Note: Install the black pr otective cover that was removed fr om the new micropr ocessor onto the defective micropr ocessor after the installation is complete. 12. Lower the small handle to secure the micropr ocessor in the socket. 13. Use the thermal grease syringe to place five drops of[...]

  • Seite 113

    Replacing the primary hard disk drive Important When you install a new hard disk drive, you also need a set of Pr oduct Recovery discs. The set of Product Recovery discs will enable the contents of the hard disk to be r estored to the same state as when the computer was originally shipped from the factory . For more information on r ecovering facto[...]

  • Seite 114

    Replacing an optical drive 1. Remove the left-side and right-side covers. See “Removing the covers” on page 84. 2. Disconnect the power cable and signal cable from the optical drive. 3. Remove the two screws that secure the drive on each side. 4. Slide the drive being replaced out the front of the computer . 5. If the drive you are replacing ha[...]

  • Seite 115

    Replacing the diskette drive 1. Remove the left-side and right-side covers. See “Removing the covers” on page 84. 2. Disconnect the signal and power cables from the rear of the har d disk drive. Note: Yo u will probably have to disconnect cables that ar e connected to the system board and other drives to allow the diskette drive to be r emoved [...]

  • Seite 116

    Replacing the power switch/ LED assembly 1. Disconnect the power switch/LED assembly cable from the system board. See “Identifying parts on the system board” on page 87. 2. Remove the front bezel. See “Removing and replacing the fr ont bezel” on page 89. 3. Remove the power switch/LED assembly by disconnecting it from the inside of the beze[...]

  • Seite 117

    Replacing the front panel card assembly 1. Remove the left-side and right-side covers. See “Removing the covers” on page 84. 2. Remove the front bezel. See “Removing and replacing the fr ont bezel” on page 89. 3. Disconnect the front USB cable and the front audio cable fr om the system board. See “Identifying parts on the system boar d”[...]

  • Seite 118

    Completing the FRU replacement After replacing FRUs, you need to install any r emoved parts, replace the cover , and reconnect any cables, including telephone lines and power cor ds. Also, depending on the FRU that is replaced, you might need to confirm the updated information in the Setup Utility program. Note: When the power cor d is first plugge[...]

  • Seite 119

    Chapter 9. Replacing FRUs (T ypes 7390, 7391, 7392, 7396, 7397, and 7398) Important Before you r eplace any FRU, read Chapter 2, “Safety information,” on page 3. These precautions and guidelines will help you work safely . FRU replacements ar e to be done by trained service technicians only . This chapter does not contain a remove and r eplace [...]

  • Seite 120

    Rear connectors The following illustration shows the locations of the connectors on the rear of the computer . 1 Standard mouse connector 9 PCI Expr ess x1 adapter or Express x16 graphics adapter connector (some models) 2 Parallel connector 10 Audio line out connector 3 Ethernet connector 11 Microphone connector [...]

  • Seite 121

    3. Disconnect all cables attached to the computer . This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer . 4. Remove any locking devices such as a padlock that secure the cover . 5. Remove the two screws at the rear of the computer cover and slide the cover to the rear . Locations The followi[...]

  • Seite 122

    Identifying parts on the system board System board locations ar e differ ent depending on the machine type. Machine T ypes 7390, 7391, and 7392 1 Micropr ocessor fan connector 11 Front panel (power switch/LED) connector 2 Micropr ocessor and heat sink 12 S ATA IDE connectors (2) 3 Memory connector 1 13 Front USB [...]

  • Seite 123

    Machine T ypes 7396, 7397, and 7398 1 Micropr ocessor and heat sink 11 Front USB connectors (2) 2 Micropr ocessor fan connector 12 Serial (COM2) connector 3 Memory connector 1 13 Front audio connectors 4 Memory connector 2 14 PCI adapter connectors (2) 5 Power connector 15 PCI Express x1 g[...]

  • Seite 124

    Removing and replacing the drive bay assembly Yo u will need to remove the drive bay assembly to access some FRUs. 1. Remove the computer cover . See “Removing the cover” on page 1 14. 2. Remove the front bezel by releasing the thr ee tabs and pivoting the top of the bezel outward. 3. Remove the two screws at the front of the chassis securing t[...]

  • Seite 125

    4. Slide the drive bay assembly forward until it stops. Disconnect the power supply and signal cables from the drives. Pivot the r ear of the drive bay assembly upward to r emove it completely from the computer . Note: To allow easier access to the cables, lift the fan plenum off the heat sink. See “Locations” on page 1 15. 5. Reverse this proc[...]

  • Seite 126

    Replacing a memory module 1. Remove the cover . See “Removing the cover” on page 1 14. 2. Remove the drive bay assembly . See “Removing and replacing the drive bay assembly” on page 1 18. 3. Locate the memory connectors. See “Identifying parts on the system board” on page 1 16. 4. Open the retaining clips and remove the failing memory m[...]

  • Seite 127

    Replacing a PCI adapter 1. Remove the computer cover . See “Removing the cover” on page 1 14. 2. Remove the screw that secures the adapter r etainer and remove the r etainer . 3. Remove the failing adapter . 4. Remove the new adapter from its static-protective package. 5. Install the new adapter into the appropriate connector on the system boar[...]

  • Seite 128

    Replacing the CMOS battery If the CMOS battery fails, the date, time, and configuration information (including passwords) ar e lost. An error message is displayed when you turn on the computer . Important Refer to “Safety notices (multi-lingual translations)” on page 7 for information about replacing and disposing of the battery . 1. Remove the[...]

  • Seite 129

    Replacing the power supply Attention Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, curr ent, and energy levels ar e present inside any component that has this label attached. There ar e no servicable parts inside these components. 1. Remove the cover . See “Removing the cover” on [...]

  • Seite 130

    10. Position the system board so that the screws holes ar e aligned and install the system board scr ews. 11 . Install the hard disk drive. Make sure to r oute the power supply cable for the system board underneath the har d disk drive. See “Replacing the hard disk drive” on page 140. 12. Reconnect all other power supply cables to the system bo[...]

  • Seite 131

    Replacing the system board (T ypes 7396, 7397, and 7398) Note: When r eplacing the system board, a new r etention bracket for the micropr ocessor heat sink is requir ed. Make sure you have a new r etention bracket before beginning this pr ocedure. 1. Remove the cover . See “Removing the cover” on page 11 4 2. Lift the fan duct off the heat sink[...]

  • Seite 132

    11 . Remove the four screws 1 securing the heat sink and fan assembly to the system board. 12. Lift the heat sink and fan assembly off the failing system board. Lay the heat sink on its side so that the thermal grease does not come in contact with anything. 13. Lift the small handle 3 and open the retainer 1 . 126 Lenovo 3000 J Se[...]

  • Seite 133

    Important T ouch only the sides of the micropr ocessor . Do not touch the gold contacts on the bottom. 14. Lift the microprocessor 2 straight up and out of the socket. Notes: a. Note the orientation of the notches 1 on the microprocessor . This is important when reinstalling the micr oprocessor on the new system boar d. b. Do not drop a[...]

  • Seite 134

    17. Lower the microprocessor straight down into the system boar d socket of the new system board. 18. Lower the microprocessor r etainer . 19. Lock the retainer with the small handle to secure the micr oprocessor in the socket. 20. The new retention bracket has plastic one-way rings on the posts that insert into the rear of the new system boar d. I[...]

  • Seite 135

    Replacing the system board (T ypes 7390, 7391, and 7392) 1. Remove the cover . See “Removing the cover” on page 1 14. 2. Lift the fan duct off the heat sink fan. 3. Remove any adapter cards installed in the PCI connectors. See “Replacing a PCI adapter” on page 121. 4. Remove the drive bay assembly . See “Removing and replacing the drive b[...]

  • Seite 136

    14. Lift the small handle 1 . Important T ouch only the sides of the micropr ocessor . Do not touch the gold contacts on the bottom. 15. Lift the microprocessor 2 straight up and out of the socket. Notes: a. Y our micropr ocessor and socket might look differ ent than the one illustrated. b. Note the orientation of the microprocessor in [...]

  • Seite 137

    16. Holding the microprocessor with your fingers, position the micr oprocessor so that the small triangle 1 on one corner is aligned with the corresponding triangle on the socket. 17. Make sure that the small handle is in the raised position. 18. Lower the microprocessor straight down into the system boar d socket of the new system board. 19.[...]

  • Seite 138

    Replacing the microprocessor (T ypes 7396, 7397, and 7398) Note: A thermal gr ease syringe is requir ed to complete the micropr ocessor installation. Make sure the gr ease syringe is available before beginning the procedur e. The FRU number for the thermal grease is 91P8835. 1. Remove the cover . See “Removing the cover” on page 1 14. 2. Lay th[...]

  • Seite 139

    6. Lift the small handle 3 and open the retainer 1 . Important T ouch only the sides of the micropr ocessor . Do not touch the gold contacts on the bottom. 7. Lift the microprocessor 2 straight up and out of the socket. Chapter 9. Replacing FRUs (T ypes 7390, 7391, 7392, 7396, 7397, and 7398) 133[...]

  • Seite 140

    Notes: a. Note the orientation of the notches 1 on the microprocessor . This is important when reinstalling the micr oprocessor on the system boar d. b. Do not drop anything onto the micropr ocessor socket while it is exposed. The socket pins must be kept as clean as possible. 8. Make sure that the micropr ocessor retainer is fully open. 9. H[...]

  • Seite 141

    11 . Lower the microprocessor straight down into the system boar d socket of the system board. 12. Lower the microprocessor r etainer . 13. Lock the retainer with the small handle to secure the micr oprocessor in the socket. 14. Use the thermal grease syringe to place five drops of gr ease on the top of the micropr ocessor . Each drop of grease sho[...]

  • Seite 142

    Replacing the microprocessor (T ypes 7390, 7391, and 7392) Note: A thermal gr ease syringe is requir ed to complete the micropr ocessor installation. Make sure the gr ease syringe is available before beginning the procedur e. The FRU number for the thermal grease is 91P8835. 1. Remove the cover . See “Removing the cover” on page 1 14. 2. Lift t[...]

  • Seite 143

    6. Lift the small handle 1 . Important Do not touch the gold contacts on the bottom of the micropr ocessor . If you must touch the micropr ocessor , touch only the sides. 7. Lift the microprocessor 2 straight up and out of the socket. Notes: a. Y our micropr ocessor and socket might look differ ent than the one illustrated. b. Note the [...]

  • Seite 144

    9. Holding the microprocessor with your fingers, position the micr oprocessor so that the small triangle on one corner is aligned with the corresponding triangle on the micropr ocessor socket. 10. Holding the microprocessor with your fingers, r emove the protective cover 2 that protects the gold contacts on the new micr oprocessor 1 . 1[...]

  • Seite 145

    13. Use the thermal grease syringe to place five drops of gr ease on the top of the micropr ocessor . Each drop of grease should be 0.03ml (3 tick marks on the grease syringe). 14. Install the heat sink and fan assembly on the system board. 15. Connect the heat sink and fan assembly to the system board. See “Identifying parts on the system board?[...]

  • Seite 146

    Replacing the hard disk drive 1. Remove the cover .See “Removing the cover” on page 1 14. 2. Remove the drive bay assembly . See “Removing and replacing the drive bay assembly” on page 1 18. 3. Remove the two screws that secure the har d disk drive bracket. 4. From the front of the chassis, slide the drive bracket to the left until it is fr[...]

  • Seite 147

    Replacing an optical drive 1. Remove the cover . See “Removing the cover” on page 1 14. 2. Remove the drive bay assembly . See “Removing and replacing the drive bay assembly” on page 1 18. 3. Remove the screws that secure the drive in the drive bay assembly . 4. Slide the drive being replaced out the front of the drive bay assembly . 5. Sli[...]

  • Seite 148

    Replacing the diskette drive 1. Remove the cover . See “Removing the cover” on page 1 14. 2. Remove the drive bay assembly . See “Removing and replacing the drive bay assembly” on page 1 18. 3. Remove the screws at the bottom of the diskette drive that secure the drive to the drive bay assembly . 4. Slide the diskette drive out of the drive[...]

  • Seite 149

    Replacing the power switch/ LED assembly 1. Remove cover . See “Removing the cover” on page 1 14. 2. Remove the drive bay assembly . See “Removing and replacing the drive bay assembly” on page 1 18. 3. Remove the hard disk drive. See “Replacing the hard disk drive” on page 140. 4. Disconnect the power switch/LED assembly cable from the [...]

  • Seite 150

    Replacing the front panel card 1. Remove cover . See “Removing the cover” on page 1 14. 2. Remove the drive bay assembly . See “Removing and replacing the drive bay assembly” on page 1 18. 3. Disconnect the front panel assembly cables from the system boar d. See “Identifying parts on the system board” on page 1 16. 4. Remove the screw t[...]

  • Seite 151

    3. Reconnect the external cables and power cords to the computer . See “Rear connectors” on page 1 14. 4. If you have replaced the system board, you must update (flash) the BIOS. See “Flash update procedur es” on page 209. 5. Some FRU replacements requir e the configuration to be updated. See Chapter 6, “Using the Setup Utility,” on pag[...]

  • Seite 152

    146 Lenovo 3000 J Series[...]

  • Seite 153

    Chapter 10. FRU lists Notes: 1. In the following tables, A CRU (Customer Replaceable Unit) is identified by either a 1, 2, or N in the CRU T ier column. A ″ 1 ″ means that the part is a T ier 1 CRU, A ″ 2 ″ means that the part is a T ier 2 CRU, and an ″ N ″ means that the part is not a CRU. 2. For some machine types, there is a column w[...]

  • Seite 154

    Machine T ype 7387 Item # 7387 FRUs FRU# CRU T ier RoHS? 1 FRU, Heat Sink/RM Kit, AMD Athlon/Sempron (all models) 41R4802 N Y 2 Micropr ocessor , 3800+ Athlon64 AM2 X2 (2.0 GHz processor , 89W) (models 21G 21B 22U 22S 22P 22M 23S 23P 23Y 24U 24F 24S 24P 24Y 25G 26U 26F 27U 27F 28G 21Q 26S 26Y 27S 27Y) 41X4241 N Y 2 Micropr ocessor , 4200+ Athlon64 [...]

  • Seite 155

    Item # 7387 FRUs FRU# CRU T ier RoHS? 4 PATA Combo RoHS TS-H492C (VIST A FW) (models 21G 21B 22U 22S 22P 22M 23S 23P 23Y 24U 24F 24S 24P 24Y 41U 41F 41S 41P 41Y 21Q 9AG 8AG 2BU 2BF 2CS 2CY 2HP 2DS 2DY 4CP 2GB 2GH 48U 48F 9HU 9HF 9JS 9JP 9JY 9KD 9PS 9PY 9QP 9SD 8DG 8ES 8EY 8FP 8GD 8HS 8HP 8HY 8JD 8NS 8NY 8PP 8QD 8KS 8KP 8KY 8SD 2JU 2JF 2NS 2NY 2RP 2[...]

  • Seite 156

    7387 FRUs FRU# CRU T ier RoHS? Mechanical kit, side cover (all models) 41N5333 2 Y Mechanical kit (all models) 41N5331 N Y Main bezel kit (all models) 41N5283 N Y Power switch/LED assembly (all models) 41N5284 N Y Shield, system board (all models) 41N5329 N Y Miscellaneous hardwar e kit (all models) 41N5334 N Y Cable, hard disk drive and optical dr[...]

  • Seite 157

    7387 Keyboards (USB, Productivity) FRU# CRU T ier RoHS? Romanian (models 21G 25G 28G 45G) 41A4987 1 Y Russian/Cy (models 21G 25G 28G 45G) 41A4988 1 Y Serbian/Cyrillic (models 21G 25G 28G 45G) 41A4989 1 Y Slovak (models 21G 25G 28G 45G) 41A4990 1 Y Spanish (models 21G 25G 28G 45G) 41A4991 1 Y Swedish/Finn (models 21G 25G 28G 45G) 41A4992 1 Y Swiss F[...]

  • Seite 158

    7387 Power Cords FRU# CRU T ier RoHS? Power Cord (LA High V olt (APU) (models 23Y 24Y 41Y 26Y 27Y 44Y) 39M5067 1 Y Power Cord (Australia, New Zealand) (models 22M 42M) 39M5102 1 Y Power Cord (Hong Kong) (models 21B) 39M5151 1 Y Power Cord (UK, Ir eland, Singapore, Malaysia, Brunei) (models 21G 25G 28G 42A 45G) 39M5150 1 Y Power Cord (T aiwan) (mode[...]

  • Seite 159

    7387 W indows XP Pro Recovery CDs FRU# CRU T ier RE (models 21G 28G 8DG) 42Y3473 1 FR/CF (models 21G 27F 28G 41F 9GF 8DG 2JF 2MF 48F 49F) 42Y4193 1 GR (models 21G 28G 8DG) 42Y4194 1 SP/LA (models 21G 22S 23S 23Y 28G 41S 41Y 27S 27Y 9PS 9PY 9SD 8ES 8EY 8GD 2DS 2DY 2NS 2NY 2SD 2PS 2PY 2UD 47S 47Y 9BG) 42Y4195 1 IT (models 21G 28G 8DG) 42Y4196 1 BR (m[...]

  • Seite 160

    7387 V ista Home Basic 32 Recovery DVDs FRU# CRU T ier CZ (models 9BG) 87H4741 1 FI (models 9BG) 87H4742 1 PL (models 9BG) 87H4743 1 RU (models 9BG) 87H4744 1 TR (models 9BG) 87H4745 1 HU (models 9BG) 87H4746 1 GK (models 9BG) 87H4747 1 PO (models 9BG) 87H4748 1 SL (models 9BG) 87H4752 1 7387 V ista Home Premium 32 Recovery DVDs FRU# CRU T ier US/U[...]

  • Seite 161

    7387 Corel Education CDs FRU# CRU T ier LA (models 22S 23S 23Y 24S 24Y 41S 41Y 26S 26Y 27S 27Y 44S 44Y) 41X0446 1 BR (models 22P 23P 24P 41P) 41X0449 1 Chapter 10. FRU lists 155[...]

  • Seite 162

    Machine T ype 7388 Item # 7388 FRUs FRU# CRU T ier RoHS? 1 Heat Sink/RM Kit, AMD Athlon/Sempron (all models) 41R4802 N Y 2 Micropr ocessor , 3800+ Athlon64 AM2 X2 (2.0 GHz processor , 89W) (models 21G 22G) 41X4241 N Y 2 Micropr ocessor , 4200+ Athlon64 AM2 X2 (2.2 GHz processor , 89W) (models 41G) 41X1421 N Y 3 Memory module, 512MB PC2-4200 - 533MH[...]

  • Seite 163

    Item # 7388 FRUs FRU# CRU T ier RoHS? 8 System board, Nvidia C51g (Remove BIOS socket) GA Level har d sub from 45C3619 (models 21G 22G 5AG 6AG 5BG 6BG) 45R5317 N Y 9 System Fan, rear w/grill (all models) 41N5339 N Y 10 Power supply , 280W , A TX, Standard (models 21G 22G 41G) 41N3479 N Y The FRUs listed in the following table are not illustrated. 7[...]

  • Seite 164

    7388 Keyboards (USB, Productivity) FRU# CRU T ier RoHS? Norwegian (models 21G 22G 41G) 41A4984 1 Y Polish (models 21G 22G 41G) 41A4985 1 Y Portuguese (models 21G 22G 41G) 41A4986 1 Y Romanian (models 21G 22G 41G) 41A4987 1 Y Russian/Cy (models 21G 22G 41G) 41A4988 1 Y Serbian/Cyrillic (models 21G 22G 41G) 41A4989 1 Y Slovak (models 21G 22G 41G) 41A[...]

  • Seite 165

    7388 W indows XP Home Recovery CDs FRU# CRU T ier FR/CF (models 21G 41G) 42Y3413 1 GR (models 21G 41G) 42Y4314 1 SP/LA (models 21G 41G) 42Y4315 1 IT (models 21G 41G) 42Y4316 1 AE (models 21G 41G) 42Y4318 1 RU (models 21G 41G) 42Y4319 1 SV (models 21G 41G) 42Y4320 1 DK (models 21G 41G) 42Y4321 1 FI (models 21G 41G) 42Y4322 1 NO (models 21G 41G) 42Y4[...]

  • Seite 166

    7388 W indows XP Pro Recovery CDs FRU# CRU T ier Multilingual 1 (models 22G 6BG) 42Y4427 1 Multilingual 2 (models 22G 6BG) 42Y4428 1 7388 V ista Home Basic 32 Recovery DVDs FRU# CRU T ier US/UK/AP/TH (models 5BG) 87H4730 1 FR/CF (models 5BG) 87H4731 1 GR (models 5BG) 87H4732 1 SP/LA (models 5BG) 87H4733 1 IT (models 5BG) 87H4735 1 RE (models 5BG) 4[...]

  • Seite 167

    7388 V ista Business 32 Recovery DVDs FRU# CRU T ier HU (models 6BG) 87H4792 1 GK (models 6BG) 87H4793 1 PO (models 6BG) 87H4794 1 SL (models 6BG) 87H4798 1 7388 Corel Education CDs FRU# CRU T ier RoHS? US (models 22U 22M 24U 26U 27U 41U 42M 42A 42T 44U) 41X0440 1 Y CF (models 24F 26F 27F 41F 44F) 41X0443 1 Y LA (models 22S 23S 23Y 24S 24Y 41S 41Y)[...]

  • Seite 168

    Machine T ype 7389 Item # 7389 FRUs FRU# CRU T ier RoHS? 1 Heat Sink/RM Kit, AMD Athlon/Sempron (all models) 41R4802 N Y 2 Micropr ocessor , 4200+ Athlon64 AM2 X2 (2.2 GHz processor , 89W) (models 41M 41A 42V) 41X1421 N Y 3 Memory module, 512MB PC2-4200 - 533MHz - DDR2 SDRAM (models 41M 41A 42V) 41X4251 2 Y 4 DVD Recordable - Multi Burner Plus -DVD[...]

  • Seite 169

    7389 FRUs FRU# CRU T ier RoHS? Cable, S ATA 250mm (all models) 41A7145 2 Y Luxshare S ATA cable, 457mm, 1 latching for Device, RoHS (all models) 26K1 186 2 Y IDE cable for T ower (2-drop) (all models) 41A7140 2 Y Modem Phone Cable (all models) 39K5120 2 Y Cable, diskette drive (RoHs) (all models) 41A7130 2 Y Mechanical kit, side cover (all models) [...]

  • Seite 170

    7389 W indows XP Pro Recovery CDs FRU# CRU T ier FR/CF (models 6BG) 42Y4193 1 GR (models 6BG) 42Y4194 1 SP/LA (models 6BG) 42Y4195 1 IT (models 6BG) 42Y4196 1 AE (models 6BG) 42Y4198 1 RU (models 6BG) 42Y4199 1 SV (models 6BG) 42Y4200 1 DK (models 6BG) 42Y4201 1 FI (models 6BG) 42Y4202 1 NO (models 6BG) 42Y4203 1 NL (models 6BG) 42Y4204 1 CZ (model[...]

  • Seite 171

    7389 V ista Home Basic 32 Recovery DVDs FRU# CRU T ier SL (models 4AG 4BG) 87H4752 1 7389 V ista Business 32 Recovery DVDs FRU# CRU T ier US/UK/AP/TH (models 6BG 44A) 87H4776 1 FR/CF (models 6BG) 87H4777 1 GR (models 6BG) 87H4778 1 SP/LA (models 6BG) 87H4779 1 IT (models 6BG) 87H4781 1 RE (models 6BG) 43C0615 1 NO (models 6BG) 87H4783 1 SV (models [...]

  • Seite 172

    Machine T ype 7390 Item # 7390 FRUs FRU# CRU T ier RoHS? 1 Heat Sink/RM Kit, AMD Athlon/Sempron (all models) 41R4802 N Y 1 Heat Sink/RM Kit, Intel ® Prescott, Cedar Mill, Smithfield, Pr esler (all models) 41R2950 N Y 2 Micropr ocessor , 3800+ Athlon64 AM2 X2 (2.0 GHz processor , 89W) (models 21B 21V 21J 22M 22Q 22H) 41X4241 N Y 2 Micropr ocessor ,[...]

  • Seite 173

    Item # 7390 FRUs FRU# CRU T ier RoHS? 5 Hard disk drive, 160GB, 7200rpm Serial ATA (models 21B 21V 21J 22M 22Q 22H 63S 63D 63Y) 40Y9035 N Y 5 Hard disk drive, 250GB, 7200rpm Serial ATA (models 41B 42H) 40Y9036 N Y 6 Diskette drive, wo/bezel (models) 7 Front I/O (USB/Audio) Cable Assembly (all models) 41N5270 N Y 8 Memory module, 512MB PC2-4200 -533[...]

  • Seite 174

    7390 Keyboards (USB Preferred - Fullwidth) FRU# CRU T ier RoHS? LA Spanish (models 63S 63D 63Y 45S 45D 45Y ) 41A5312 1 Y 7390 Keyboards (USB, Productivity) FRU# CRU T ier RoHS? US English (models 22M 22Q 22H 42H) 41A4961 1 Y Hong Kong/T aiwan (models 41B) 41A4968 1 Y 7390 mice FRU# CRU T ier RoHS? Mouse, USB optical wheel (models B1G 21G D1J D2J D3[...]

  • Seite 175

    7390 W indows XP Home Recovery CDs FRU# CRU T ier Hong Kong - TC (models 41B) 42T8727 1 7390 W indows XP Pro Recovery CDs FRU# CRU T ier US/UK/AP/TH (models 21G) 42Y3466 1 SP/LA (models 45S 45D 45Y 63S 63D 63Y ) 42Y4195 1 Japanese (models 21J) 42T8681 1 T aiwan -TC (models 21V) 42T8695 1 Hong Kong - TC (models 21B) 42T8702 1 7390 V ista Home Basic [...]

  • Seite 176

    Machine T ype 7392 Item # 7392 FRUs FRU# CRU T ier RoHS? 1 Heat Sink/RM Kit, AMD Athlon/Sempron (all models) 41R4802 N Y 1 Heat Sink/RM Kit, Intel Prescott, Cedar Mill, Smithfield, Pr esler (all models) 41R2950 N Y 2 Micropr ocessor , 3800+ Athlon64 AM2 X2 (2.0 GHz processor , 89W) (models 21B 22H) 41X4241 N Y 3 Combo 48 -32 -48 -16 - - DVD - ROM -[...]

  • Seite 177

    7392 FRUs FRU# CRU T ier RoHS? Shield, EMC, 5.25in. drive bay (all models) 41A7162 N Y Cable, Serial-A T A, (18in. RoHs) (all models) 41A7145 N Y Shield, EMC, diskette drive bay (all models) 41A7146 N Y Cable, diskette drive (all models) 41A7147 N Y Cover (all models) 41A7148 2 Y Chassis Kit Assembly with bezels (all models) 41N5251 N Y Bezel Assem[...]

  • Seite 178

    7392 V ista Home Basic 32 Recovery DVDs FRU# CRU T ier US/UK/AP/TH (models) 87H4730 1 FR/CF (models) 87H4731 1 GR (models) 87H4732 1 SP/LA (models) 87H4733 1 BR (models) 87H4734 1 IT (models) 87H4735 1 RE (models) 43C061 1 1 JP (models) 87H4736 1 NO (models) 87H4737 1 SV (models) 87H4738 1 DK (models) 87H4739 1 NL (models) 87H4740 1 CZ (models) 87H[...]

  • Seite 179

    7392 V ista Home Premium 32 Recovery DVDs FRU# CRU T ier RU (models) 87H4767 1 TR (models) 87H4768 1 HU (models) 87H4769 1 GK (models) 87H4770 1 PO (models) 87H4771 1 TW (models) 87H4772 1 HK (models) 87H4773 1 KR (models) 87H4774 1 SL (models) 87H4775 1 7392 V ista Business 32 Recovery DVDs FRU# CRU T ier US/UK/AP/TH (models) 87H4776 1 FR/CF (mode[...]

  • Seite 180

    Machine T ype 7393 Item # 7393 FRUs FRU# CRU T ier RoHS? 1 FRU, Heat Sink/RM Kit, Intel Prescott, Cedar Mill, Smithfield, Pr esler (all models) 41R4803 N Y 2 Micropr ocessor , Pentium ® E2140 CONROE-L 800/1600MHZ-1M, LGA, EM64T (models M7S M8S M9S MAS) 43C1967 N Y 2 Micropr ocessor , Intel 820 - A0 Smithfield (models 21U 21F 21S 21P 21Y 22U 22F 22[...]

  • Seite 181

    Item # 7393 FRUs FRU# CRU T ier RoHS? 4 Combo 48 -32 -48 -16 - - DVD - ROM - CDR W (models 22U 22F 23V 24U 24F 55U 55F 55S 55P 55Y 22Q 94H 95B EAS EAP EA Y F7D F8S F8P F8Y G4S G4P G4Y G5D H6S H6P H6Y H7D 5JS 5JP 5JY HAD 3KA M7S M9S) 41X3548 N Y 4 Combo 48 -32 -48 -16 - - DVD - ROM - CDR W (models 22U 22F 23V 24U 24F 55U 55F 55S 55P 55Y 22Q 94H 95B [...]

  • Seite 182

    Item # 7393 FRUs FRU# CRU T ier RoHS? 8 System board, 946GZ D (models 21U 21F 22U 22F 23V 24U 24F 26U 26F 27U 27F 51U 51F 51M 51A 51T 53B 54H 55U 55F 55S 55P 55Y 56U 56F 57G 57V 22Q 26S 26Y 27S 27Y 51S 51Y 56S 56Y 92M 93V 94H 28G 61G 95B 2AA 42Q 2BS 2BY 2CQ 2BP 2DS 2DY 2DP 5AS 5A Y 5BU 5BF 5CU 5CF 5DU 5DF 5KA 5KQ 5KT 5KV 5FH 5GB 5HB 5HH 6AU 6AF 8AA[...]

  • Seite 183

    Item # 7393 FRUs FRU# CRU T ier RoHS? 8 System board, 946GZ D (models 21U 21F 22U 22F 23V 24U 24F 26U 26F 27U 27F 51U 51F 51M 51A 51T 53B 54H 55U 55F 55S 55P 55Y 56U 56F 57G 57V 22Q 26S 26Y 27S 27Y 51S 51Y 56S 56Y 92M 93V 94H 28G 61G 95B 2AA 42Q 2BS 2BY 2CQ 2BP 2DS 2DY 2DP 5AS 5A Y 5BU 5BF 5CU 5CF 5DU 5DF 5KA 5KQ 5KT 5KV 5FH 5GB 5HB 5HH 6AU 6AF 8AA[...]

  • Seite 184

    7393 FRUs FRU# CRU T ier RoHS? Power switch/LED assembly (all models) 41N5284 N Y Shield, system board (945GZ) (all models) 41N5286 N Y Miscellaneous hardwar e kit (all models) 41N5334 N Y Cable, hard disk drive and optical drive signal (2-dr op) (all models) 41A7875 N Y Card Reader Bezel (all models) 41N5340 2 Y 7393 Keyboards (USB Preferred - Ful[...]

  • Seite 185

    7393 Keyboards (USB, Productivity) FRU# CRU T ier RoHS? Romanian (models 25G 52G 57G 58G 91G) 41A4987 1 Y Russian/Cy (models 25G 52G 57G 58G 91G) 41A4988 1 Y Serbian/Cyrillic (models 25G 52G 57G 58G 91G) 41A4989 1 Y Slovak (models 25G 52G 57G 58G 91G) 41A4990 1 Y Spanish (models 25G 52G 57G 58G 91G) 41A4991 1 Y Swedish/Finn (models 25G 52G 57G 58G [...]

  • Seite 186

    7393 Power Cords FRU# CRU T ier RoHS? Power Cord (Brazil) (models 21P 22P 24P 55P) 39M5232 1 Y Power Cord (LA High V olt (APU) (models 21Y 22Y 24Y 55Y 26Y 27Y 51Y 56Y) 39M5067 1 Y Power Cord (Australia, New Zealand) (models 51M 92M) 39M5102 1 Y Power Cord (Hong Kong) (models 53B 54H 94B 94H) 39M5151 1 Y Power Cord (UK, Ir eland, Singapore, Malaysia[...]

  • Seite 187

    7393 W indows XP Pro Recovery CDs FRU# CRU T ier US/UK/AP/TH (models 21U 22U 26U 51U 51M 51A 51T 52G 54H 55U 57G 22Q 91G 92M 3KA 42Q F1U G1U G2U 2CQ GCU GDU 5BU 5DU 5FH 5HH 6GU 8AM 8AA 8AQ 97M) 42Y3466 1 RE (models 52G 57G 91G) 42Y3473 1 FR/CF (models 21F 22F 26F 51F 52G 55F 57G 91G F1F G1F G2F GCF GDF 5BF 5DF 6GF) 42Y4193 1 GR (models 52G 57G 91G)[...]

  • Seite 188

    7393 V ista Home Premium 32 Recovery DVDs FRU# CRU T ier FR/CF (models GHF 8KF) 87H4754 1 HK (models 98B) 87H4773 1 7393 V ista Business 32 Recovery DVDs FRU# CRU T ier US/UK/AP/TH (models 42Q F1U G1U G2U 2CQ GCU GDU 5BU 5DU 5FH 5HH 6GU 8AM 8AA 8AQ 97M) 87H4776 1 FR/CF (models F1F G1F G2F GCF GDF 5BF 5DF 6GF) 87H4777 1 SP/LA (models E7S E7Y E8D G7S[...]

  • Seite 189

    Machine T ype 7394 Item # 7394 FRUs FRU# CRU T ier RoHS? 1 FRU, Heat Sink/RM Kit, Intel Prescott, Cedar Mill, Smithfield, Pr esler (all models) 41R4803 N Y 2 Micropr ocessor , Intel 820 - A0 Smithfield (models 21G) 41T1704 N Y 2 Micropr ocessor , Intel 925 (models 41G 42G) 41X2413 N Y 3 Memory module, 512MB PC2-4200 - 533MHz - DDR2 SDRAM (models 21[...]

  • Seite 190

    Item # 7394 FRUs FRU# CRU T ier RoHS? 8 System board, 946GZ B (models 21G 42G 94A 94T 22G 51G) Note: When you order a new system boar d you must also order a new retention bracket for the heat sink. 43C3504 N Y 8 System board, 946GZ D (models 21G 42G 94A 94T 22G 51G) Note: When you order a new system boar d you must also order a new retention brack[...]

  • Seite 191

    7394 Keyboards (USB, Productivity) FRU# CRU T ier RoHS? French (models 21G 41G 42G 91G) 41A4972 1 Y German (models 21G 41G 42G 91G) 41A4975 1 Y Greek (models 21G 41G 42G 91G) 41A4976 1 Y Hebrew (models 21G 41G 42G 91G) 41A4977 1 Y Hungarian (models 21G 41G 42G 91G) 41A4978 1 Y Iceland (models 21G 41G 42G 91G) 41A4979 1 Y Italian (models 21G 41G 42G[...]

  • Seite 192

    7394 Power Cords FRU# CRU T ier RoHS? Power Cord (Denmark) (models 21G 41G 42G 91G) 39M5129 1 Y Power Cord (Switzerland) (models 21G 41G 42G 91G) 39M5157 1 Y Power Cord (Israel) (models 21G 41G 42G 91G) 39M5171 1 Y Power Cord (South Africa) (models 21G 41G 42G 91G) 39M5143 1 Y 7394 W indows XP Home Recovery CDs FRU# CRU T ier US/UK/AP/TH (models 21[...]

  • Seite 193

    7394 W indows XP Pro Recovery CDs FRU# CRU T ier NL (models 42G 91G) 42Y4204 1 CZ (models 42G 91G) 42Y4205 1 HE (models 42G 91G) 42Y4206 1 PL (models 42G 91G) 42Y4207 1 TR (models 42G 91G) 42Y4208 1 HU (models 42G 91G) 42Y4209 1 PO (models 42G 91G) 42Y4210 1 GK (models 42G 91G) 42Y421 1 1 SL (models 42G 91G) 42Y4212 1 Multilingual 1 (models 42G 91G[...]

  • Seite 194

    Machine T ype 7395 Item # 7395 FRUs FRU# CRU T ier RoHS? 1 FRU, Heat Sink/RM Kit, Intel Prescott, Cedar Mill, Smithfield, Pr esler (all models) 41R4803 N Y 2 Micropr ocessor , Intel 820 - A0 Smithfield (models 21M 21A 22V) 41T1704 N Y 2 Micropr ocessor , Intel 925 (models 41B 42H 43M 43A 44V) 41X2413 N Y 2 Micropr ocessor , CONROE E6300 1066/1860MH[...]

  • Seite 195

    Item # 7395 FRUs FRU# CRU T ier RoHS? 6 Front panel car d (USB/Audio) assembly (all models) 41N5330 N Y 7 Hard disk drive, 80GB, 7200rpm, serial ATA (models 41B 42H) 40Y9034 N Y 7 Hard disk drive, 160GB, 7200rpm, serial ATA (models 21M 21A 22V) 40Y9035 N Y 7 Hard disk drive, 250GB, 7200rpm, serial ATA (models 43M 43A 44V 91S 91P 91Y 91M 91B 91H) 40[...]

  • Seite 196

    7395 FRUs FRU# CRU T ier RoHS? Shield, system board (945GZ) (all models) 41N5286 N Y Miscellaneous hardwar e kit (all models) 41N5334 N Y Cable, hard disk drive and optical drive signal (2-dr op) (all models) 41A7875 N Y Card Reader Bezel (all models) 41N5340 2 Y Dongle Cable - DMS59 to dual VGA (all models) 41D2399 2 Y Battery 3V -lithium (all mod[...]

  • Seite 197

    7395 Power Cords FRU# CRU T ier RoHS? Power Cord (Hong Kong) (models 41B 42H 91B 91H) 39M5151 1 Y Power Cord (UK, Ir eland, Singapore, Malaysia, Brunei) (models 21A 43A) 39M5150 1 Y Power Cord (T aiwan) (models 22V 44V) 39M5246 1 Y Power Cord (Italy) (models 91S 91Y) 39M5164 1 Y Power Cord (G models) (models 21A 43A) 39M5122 1 Y Power Cord (South A[...]

  • Seite 198

    7395 V ista Business 32 Recovery DVDs FRU# CRU T ier NO (models 49G 99G) 87H4783 1 SV (models 49G 99G) 87H4784 1 DK (models 49G 99G) 87H4785 1 NL (models 49G 99G) 87H4786 1 CZ (models 49G 99G) 87H4787 1 FI (models 49G 99G) 87H4788 1 PL (models 49G 99G) 87H4789 1 RU (models 49G 99G) 87H4790 1 TR (models 49G 99G) 87H4791 1 HU (models 49G 99G) 87H4792[...]

  • Seite 199

    Machine T ype 7396 Item # 7396 FRUs FRU# CRU T ier RoHS? 1 Heat Sink/RM Kit, Intel Prescott, Cedar Mill, Smithfield, Pr esler (all models) 41R4803 N Y 2 Micropr ocessor , Celeron ® 420 CONROE-L 800/1600MHZ-512K,LGA,EM64T (models 74B 74H) 43C3835 N Y 2 Micropr ocessor , Pentium E2140 CONROE-L 800/1600MHZ-1M, LGA, EM64T (models D6S D7S D8S) 43C1967 [...]

  • Seite 200

    Item # 7396 FRUs FRU# CRU T ier RoHS? 3 HLDS RoHS RAMBO-8 drive (models 23G 24B 25H 41M 26B 6BV 6AM 6AA 6A T 4GS 4GD 4GY 5FS 5FD 5FY 9DS 9DD 9DY 4KB 4KH 74B 74H F2B F2H D8S) 42Y9371 N Y 3 HLDS RAMBO-8 GSA-H10N F/W JX07 (models 23G 24B 25H 41M 26B 27M 29B 28H 43M 44B 44H 9AA 9A T 9A V 9BB 9BH 8CB 8CH 6BV 6AM 6AA 6A T 5BV 5CM 5AA 5A T 4GS 4GD 4GY 5FS[...]

  • Seite 201

    Item # 7396 FRUs FRU# CRU T ier RoHS? 9 System board, 946GZ D (models 21M 21A 21Q 21T 21H 22G 22V 23G 24B 25H 41M 8AG 27M 29B 28H 43M 44B 44H 9AA 9A T 9A V 9BB 9BH 8BG 8CB 8CH 6BV 6AM 6A T 6A T 45G 5BV 5CM 5AA 5A T ’4CS 4CD 4CY 4FS 4FD 4FY 4GS 4GD 4GY 4JS 4JD 4JY 5FS 5FD 5FY 9DS 9DD 9DY 4KB 4KH 74B 74H F2B F2H D6S D7S D8S) Note: When you order a [...]

  • Seite 202

    7396 Keyboards (USB Preferred - Fullwidth) FRU# CRU T ier RoHS? US English (models 4KH 74H F2H ) 41A5289 1 Y Chinese/US (models 4KB 74B F2B ) 41A5296 1 Y LA Spanish (models 4CS 4CD 4CY 4FS 4FD 4FY 4GS 4GD 4GY 4JS 4JD 4JY 5FS 5FD 5FY 9DS 9DD 9DY D6S D7S D8S) 41A5312 1 Y 7396 Keyboards (USB, Productivity) FRU# CRU T ier RoHS? US English (models 21M 2[...]

  • Seite 203

    7396 Keyboards (Fingerprint Reader , USB) FRU# CRU T ier RoHS? US English (models 41M 42G) 41A5248 1 Y Arabic (models 42G) 41A5249 1 Y Arabic/French (models 42G) 41A5250 1 Y Belgian/French (models 42G) 41A5251 1 Y Belgian/UK (models 42G) 41A5252 1 Y Brazil/Portuguese (models 42G) 41A5253 1 Y Bulgarian (models 42G) 41A5254 1 Y Chinese/US (models 42G[...]

  • Seite 204

    7396 mice FRU# CRU T ier RoHS? Mouse, USB optical wheel (all models) 41A5085 1 Y Mouse, USB optical wheel - Logitec (all models) 41A5089 1 Y 7396 Adapters and miscellaneous FRUs FRU# CRU T ier RoHS? AT I X300SE 128MB (models 41M 42G) 39J9635 1 Y Internal USB Memory Card Reader (models 21M 21A 21Q 21T 21H 22G 22V 23G 24B 25H 41M 42G) 41X2089 1 Y Spe[...]

  • Seite 205

    7396 W indows XP Pro Recovery CDs FRU# CRU T ier SP/LA (models 22G 23G 42G 8AG 8BG 4CS 4CD 4CY 4GS 4GD 4GY D6S D8S 4JS 4JD 4JY 5FS 5FD 5FY 9DS 9DD 9DY ) 42Y4195 1 IT (models 22G 23G 42G 8AG 8BG ) 42Y4196 1 AE (models 22G 23G 42G 8AG 8BG ) 42Y4198 1 RU (models 22G 23G 42G 8AG 8BG ) 42Y4199 1 SV (models 22G 23G 42G 8AG 8BG ) 42Y4200 1 DK (models 22G [...]

  • Seite 206

    7396 V ista Business 32 Recovery DVDs FRU# CRU T ier NL (models 8AG 8BG) 87H4786 1 CZ (models 8AG 8BG) 87H4787 1 FI (models 8AG 8BG) 87H4788 1 PL (models 8AG 8BG) 87H4789 1 RU (models 8AG 8BG) 87H4790 1 TR (models 8AG 8BG) 87H4791 1 HU (models 8AG 8BG) 87H4792 1 GK (models 8AG 8BG) 87H4793 1 PO (models 8AG 8BG) 87H4794 1 TW (models 5BV) 87H4795 1 S[...]

  • Seite 207

    Machine T ype 7397 Item # 7397 FRUs FRU# CRU T ier RoHS? 1 Heat Sink/RM Kit, Intel Prescott, Cedar Mill, Smithfield, Pr esler (all models) 41R4803 N Y 1 Heat Sink/RM Kit, Intel Prescott, Cedar Mill, Smithfield, Pr esler (all models) 41R2950 N Y 2 Micropr ocessor , Intel 820 - A0 Smithfield (models 21J 22J 23G) 41T1704 N Y 2 Micropr ocessor , Intel [...]

  • Seite 208

    Item # 7397 FRUs FRU# CRU T ier RoHS? 8 Memory module, 512MB PC2-4200 - 533MHz - DDR2 SDRAM (models 21J 22J 23G 45G) 41X4251 2 Y 8 Memory module, 1GB PC2-4200 - 533MHz - DDR2 SDRAM (models 41J 42J) 41X4252 2 Y 9 System board, 945GZ D - Intel based (models 21J 22J 23G 41J 42J 8AG 93J 94J 8BG 6AJ 43G 5AJ 91J 92J) Note: When you order a new system boa[...]

  • Seite 209

    7397 Keyboards (USB Preferred - Fullwidth) FRU# CRU T ier RoHS? Japanese (models 22J 42J) 41A5310 1 Y 7397 Keyboards (USB Productivity) FRU# CRU T ier RoHS? US English (models 23G 45G) 41A4961 1 Y Arabic (models 23G 45G) 41A4962 1 Y Arabic/French (models 23G 45G) 41A4963 1 Y Belgian/French (models 23G 45G) 41A4964 1 Y Belgian/UK (models 23G 45G) 41[...]

  • Seite 210

    7397 Adapters and miscellaneous FRUs FRU# CRU T ier RoHS? AT I X300SE 128MB (models 41J 42J) 39J9635 1 Y Internal USB Memory Card Reader (models 21J 23G 41J) 41X2089 1 Y Speaker Brick - Hong Kong, EMEA (models 45G) 89P8573 1 Y 7397 Power Cords FRU# CRU T ier RoHS? Power Cord (Japan) (models 21J 22J 41J 42J) 39M5193 1 Y Power Cord (UK, Ir eland, Sin[...]

  • Seite 211

    7397 W indows XP Pro Recovery CDs FRU# CRU T ier Multilingual 2 (models 23G 8BG) 42Y4428 1 7397 V ista Business 32 Recovery DVDs FRU# CRU T ier US/UK/AP/TH (models 8BG) 87H4776 1 FR/CF (models 8BG) 87H4777 1 GR (models 8BG) 87H4778 1 SP/LA (models 8BG) 87H4779 1 IT (models 8BG) 87H4781 1 RE (models 8BG) 43C0615 1 JP (models 5AJ 93J 94J) 87H4782 1 N[...]

  • Seite 212

    Machine T ype 7398 Item # 7398 FRUs FRU# CRU T ier RoHS? 1 Heat Sink/RM Kit, Intel Prescott, Cedar Mill, Smithfield, Pr esler (all models) 41R4803 N Y 1 Heat Sink/RM Kit, Intel Prescott, Cedar Mill, Smithfield, Pr esler (all models) 41R2950 N Y 2 Micropr ocessor , Intel 925 (models 41M 42V) 41X2413 N Y 2 Micropr ocessor , CONROE E6300 1066/1860MHZ-[...]

  • Seite 213

    Item # 7398 FRUs FRU# CRU T ier RoHS? 9 System board, 945GZ D - Intel based (models 41M 42V 91H 92H 93B 94B 97M 95A 95T 96B 96H) Note: When you order a new system boar d you must also order a new retention bracket for the heat sink. 87H6456 N Y 9 System board, 946GZ B (models 41M 42V 91H 92H 93B 94B 97M 95A 95T 96B 96H) Note: When you order a new s[...]

  • Seite 214

    7398 mice FRU# CRU T ier RoHS? Mouse, USB optical wheel (all models) 41A5085 1 Y Mouse, USB optical wheel - Logitec (all models) 41A5089 1 Y 7398 Adapters and miscellaneous FRUs FRU# CRU T ier RoHS? Internal USB Memory Card Reader (models 41M 42V 91B 91H 92B 92H) 41X2089 1 Y Boston - AT I X700 PRO 128MB (models 91B 91H 92B 92H) 39J6203 1 Y 7398 Pow[...]

  • Seite 215

    Chapter 11 . Additional Service Information This chapter provides additional information that the service r epresentative might find helpful. Security features Security features in this section include the following: v Passwords v V ital Product Data v Management Information Format (MIF) Hardware controlled Passwords Hardwar e controlled passwor ds[...]

  • Seite 216

    Updating (flashing) BIOS from a diskette 1. Insert a system program update (flash) diskette into the diskette drive. system program updates ar e available at http://www .lenovo.com/support on the W orld W ide W eb. 2. T urn on the computer . If it is already on, you must turn it off and back on. The update begins. 3. Follow the instructions on the [...]

  • Seite 217

    Power management Power management reduces the power consumption of certain components of the computer such as the system power supply , processor , hard disk drives, and some monitors. Automatic configuration and power interface (ACPI) BIOS Being an ACPI BIOS system, the operating system is allowed to control the power management features of the co[...]

  • Seite 218

    Recovering software When you install a new hard disk drive, you also need a set of Pr oduct Recovery discs. The set of Product Recovery discs will enable the contents of the har d disk to be restor ed to the same state as when the computer was originally shipped from the factory . For more information on recovering factory-installed softwar e, refe[...]

  • Seite 219

    Appendix. Notices Lenovo may not offer the pr oducts, services, or features discussed in this document in all countries. Consult your local Lenovo repr esentative for information on the products and services curr ently available in your area. Any refer ence to a Lenovo product, pr ogram, or service is not intended to state or imply that only that L[...]

  • Seite 220

    vary significantly . Some measurements may have been made on development-level systems and there is no guarantee that these measur ements will be the same on generally available systems. Furthermore, some measur ements may have been estimated through extrapolation. Actual r esults may vary . Users of this document should verify the applicable data [...]

  • Seite 221

    [...]

  • Seite 222

    Part Number: 41X8137 Printed in USA (1P) P/N: 41X8137[...]