Deutsch dropdown-ico

Konica Minolta C6500 Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82

Zur Seite of

Ähnliche Gebrauchsanleitungen

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Konica Minolta C6500 an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Konica Minolta C6500, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Konica Minolta C6500 die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Konica Minolta C6500. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Konica Minolta C6500 sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Konica Minolta C6500
- Den Namen des Produzenten und das Produktionsjahr des Geräts Konica Minolta C6500
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Konica Minolta C6500
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Konica Minolta C6500 zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Konica Minolta C6500 und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Konica Minolta finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Konica Minolta C6500 zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Konica Minolta C6500, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Konica Minolta C6500 widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    [...]

  • Seite 2

    .[...]

  • Seite 3

    bizhub PRO C6500 / bizhub PRO C6500e Contents-1 Contents 1 Introduction CMS ............. .............. .............. .............. .............. .............. ............ 1-3 Notices to the customer who emplo ys the CMS ............ .............. . 1-3 Registered tradem ark ........ .............. .............. .............. .............[...]

  • Seite 4

    Contents-2 bizhub PRO C6500 / bizhub PRO C6500e 3 PF-601/HT504 3.1 Maintenance procedure of t he tray section ....... .............. ............... 3-3 Removing the pick-up rubber/paper fe ed roller ................. ............ 3-3 Reinstalling the pick-up r ubber/paper feed rolle r ............... .......... 3-10 Removing separation roller ....[...]

  • Seite 5

    1 Introduction[...]

  • Seite 6

    [...]

  • Seite 7

    Introduction 1 bizhub PRO C6500 / bizhub PRO C6500e 1-3 1 Introduction CMS The CMS (Customer Maintenance Suppo rt) is a system that supports the customer who conducts a parts replacement ope ration by himself without getting an technical assistance from the customer engineer, to minimize the downtime (shutdown peri od of the machine operation) of t[...]

  • Seite 8

    1 Introduction 1-4 bizhub PRO C6500 / bizhub PRO C6500e 1.1 Safety instructions For your safe operation, the following are the desc riptions of the notices and requests that you have to follow when re placing parts. Be sure to read them carefully before conduct ing any part replacement operation. - Be sure to keep this CMS Replacement Instructions [...]

  • Seite 9

    Introduction 1 bizhub PRO C6500 / bizhub PRO C6500e 1-5 Operations before replacing any part 7 CAUTION Ignoring this caut ions could cause i njury or damage to property. % Do not ignore these safety advices. CMS part replacement operation 7 WARNING Ignoring this warnings could cause serious injury or even death. % Do not ignore these safety advices[...]

  • Seite 10

    1 Introduction 1-6 bizhub PRO C6500 / bizhub PRO C6500e Power plug 7 WARNING Ignoring this warnings could cause serious injury or even death. % Do not ignore these safety advices. 7 CAUTION Ignoring this caution s could cause injury or damage to property. % Do not ignore these safety advices. Warning Symbol Be sure to avoid plugging or unplugging t[...]

  • Seite 11

    Introduction 1 bizhub PRO C6500 / bizhub PRO C6500e 1-7 When any abnormal condition is found 7 WARNING Ignoring this warnings could cause serious injury or even death. % Do not ignore these safety advices. 7 CAUTION Ignoring this caut ions could cause i njury or damage to property. % Do not ignore these safety advices. Warning Symbol When the copie[...]

  • Seite 12

    1 Introduction 1-8 bizhub PRO C6500 / bizhub PRO C6500e 1.2 Caution notation s and caution labels For this copier, th ere are the caution nota tions or labels for safety operations provided at the l ocations as shown below. Be su re to take every care to avoid any accidents while in the part replacement operation. The fixing unit is very hot. To av[...]

  • Seite 13

    Introduction 1 bizhub PRO C6500 / bizhub PRO C6500e 1-9 DO NOT throw the toner recovery box into a fire. If it is thrown into a fire, the toner may ignite and cause a dangerous situation. WARNING[...]

  • Seite 14

    1 Introduction 1-10 bizhub PRO C6500 / bizhub PRO C6500e[...]

  • Seite 15

    2 bizhub PRO C6500/bizhub PRO C6500e[...]

  • Seite 16

    [...]

  • Seite 17

    bizhub PRO C6500/bizhub PRO C6500e 2 bizhub PRO C6500 / bizhub PRO C6500e 2-3 2 bizhub PRO C6500/bizhub PRO C6500e 2.1 Maintenance procedure of the housing section Removing the dust-proof filter 1 assy Periodically replac ed parts/cycle: - Dust-proof filter 1 assy: Every 200, 000 prints (actual re placement cycle: Varies depending on the coverage, [...]

  • Seite 18

    2 bizhub PRO C6500/bizhub PRO C6500e 2-4 bizhub PRO C6500 / bizhub PRO C6500e 4 Remove the screw, and re move the filter cover. 5 Remove the dust-proof filter 1 assy. Reinstalling the dust -proof filter 1 assy % Reinstall the above parts following the removal steps in reverse. screw filter cover dust-proof filter 1 assy[...]

  • Seite 19

    bizhub PRO C6500/bizhub PRO C6500e 2 bizhub PRO C6500 / bizhub PRO C6500e 2-5 Removing the dust-proof filter 2 assy Periodically replac ed parts/cycle: - Dust-proof filter 2 a ssy: Every 200,000 prints 1 Turn OFF the sub power switch. 2 Open the left front door, and then turn O FF the main power switch. 3 Unplug the power cord. left front door main[...]

  • Seite 20

    2 bizhub PRO C6500/bizhub PRO C6500e 2-6 bizhub PRO C6500 / bizhub PRO C6500e 4 Loosen the two screws and remove the filt er cover. 5 Pull out the dust-proof filter 2 assy from the filter cover. Reinstalling the dust -proof filter 2 assy % Reinstall the above parts following the removal steps in reverse. screws filter cov er dust-proof filter 2 as [...]

  • Seite 21

    bizhub PRO C6500/bizhub PRO C6500e 2 bizhub PRO C6500 / bizhub PRO C6500e 2-7 2.2 Maintenance procedure of the toner co llection box Removing the toner collection box assy Periodically replac ed parts/cycle: - Toner collection box assy: Every 50,000 pr ints 1 Turn OFF the sub power switch. 2 Open the left front door, and then turn O FF the main pow[...]

  • Seite 22

    2 bizhub PRO C6500/bizhub PRO C6500e 2-8 bizhub PRO C6500 / bizhub PRO C6500e 4 Open the toner collection door, an d pull out the toner collection box assy. toner collection door toner collection box assy[...]

  • Seite 23

    bizhub PRO C6500/bizhub PRO C6500e 2 bizhub PRO C6500 / bizhub PRO C6500e 2-9 5 Peel off the label on the toner col lection box assy and close the opening of the tone r collection box assy with the label. Reinstalling the toner collection box assy % Reinstall the above parts following the removal steps in reverse. label label opening toner collecti[...]

  • Seite 24

    2 bizhub PRO C6500/bizhub PRO C6500e 2-10 bizhub PRO C6500 / bizhub PRO C6500e 2.3 Maintenance procedure of the paper feeding section Removing the pick-up roller /paper feed roller rubber Periodically replac ed parts/cycle: - Pick-up roller: Every 2,400,000 prints (actual replace ment cycle: every 800,000 feed) - Paper feed roller rubber: Every 400[...]

  • Seite 25

    bizhub PRO C6500/bizhub PRO C6500e 2 bizhub PRO C6500 / bizhub PRO C6500e 2-11 4 Pull out the paper feed tray 1. 5 Remove the four screws and remo ve the paper feed unit cover. paper feed tray 1 screws screws paper feed unit cover paper feed unit cover[...]

  • Seite 26

    2 bizhub PRO C6500/bizhub PRO C6500e 2-12 bizhub PRO C6500 / bizhub PRO C6500e 6 Disconnect the connector 1. 7 Remove the screw and loose n the fixing shaft screw. 8 Slide the paper feed unit in the direction of the arrow, and lift the unit to remove it disconnecting the connector 2. connector 1 screw fixing shaft screw connector 2 paper feed unit[...]

  • Seite 27

    bizhub PRO C6500/bizhub PRO C6500e 2 bizhub PRO C6500 / bizhub PRO C6500e 2-13 9 Remove the two C-clips, slide the two bea rings outward, and remove the paper feed roller assy. – Before installing the pa per feed roller assy, make sure the rollers are free of grease or dust. C-clips bearing paper feed roller assy bearing[...]

  • Seite 28

    2 bizhub PRO C6500/bizhub PRO C6500e 2-14 bizhub PRO C6500 / bizhub PRO C6500e 10 Remove the b earing. 11 Remove the C-clip 1 and remove the pick-up roller. – When installing th e pick-up roller, be sure that the arrow mark 1 is facing toward the C-clip 1. 12 Remove the C-clip 2 and remove the paper feed roller. – When installing the paper feed[...]

  • Seite 29

    bizhub PRO C6500/bizhub PRO C6500e 2 bizhub PRO C6500 / bizhub PRO C6500e 2-15 Removing the separati on roller ru bber Periodically replac ed parts/cycle: - Separation roller rubber: Every 400,000 prints (actual replacement cycle: every 125,000 feed) 2 Note The tray 1 was used to illu strate th e replacement proce dure below. The procedure is the s[...]

  • Seite 30

    2 bizhub PRO C6500/bizhub PRO C6500e 2-16 bizhub PRO C6500 / bizhub PRO C6500e 4 Remove the paper feed roller assy. For details, refer to "Removing the pick-up roller/paper feed roller rubber" on page 2-10. 5 Remove the C-clip and remo ve the separation roller. – Before installing the sep aration roll er, make sure the roller is free of[...]

  • Seite 31

    bizhub PRO C6500/bizhub PRO C6500e 2 bizhub PRO C6500 / bizhub PRO C6500e 2-17 2.4 Maintenance procedure of the bypass feed tray section Removing the pick-up roller/paper feed roller rubber Periodically replac ed parts/cycle: - Pick-up roller: Every 4,000,000 prints (actual replacement c ycle: every 800,000 feed) - Paper feed roller rubber: Every 1[...]

  • Seite 32

    2 bizhub PRO C6500/bizhub PRO C6500e 2-18 bizhub PRO C6500 / bizhub PRO C6500e 4 While lifting the lever marked in the pi cture, turn the handle in the arrow marked direction and pull out the ADU. 5 Remove the six screws and remove the paper feed solenoid cover. lever screws paper feed solenoi d cover screws[...]

  • Seite 33

    bizhub PRO C6500/bizhub PRO C6500e 2 bizhub PRO C6500 / bizhub PRO C6500e 2-19 6 Remove the C-clip. C-clip bearing paper feeder roller unit[...]

  • Seite 34

    2 bizhub PRO C6500/bizhub PRO C6500e 2-20 bizhub PRO C6500 / bizhub PRO C6500e 7 Remove the bearing and remove the paper feed roller unit. – When installing the pape r feed roller unit, be sure to fit the actuator in the detection secti on of th e paper empty sensor/BP (PS47). – When installing the paper feed rolle r unit, bring the tip of the [...]

  • Seite 35

    bizhub PRO C6500/bizhub PRO C6500e 2 bizhub PRO C6500 / bizhub PRO C6500e 2-21 9 Remove the pick-up roller from the pick-up roller assy. 10 Remove the paper feed roller assy from the shaft. 11 Remove the paper feed roller rubbe r from the paper feed roller assy. – When installing the paper feed ro ller rubber, be sure that the painted mark is fac[...]

  • Seite 36

    2 bizhub PRO C6500/bizhub PRO C6500e 2-22 bizhub PRO C6500 / bizhub PRO C6500e 2.5 Maintenance procedure of the fusing section 7 CAUTION Precaution for high temperature Immediately after turning of f the main power switch or the sub power switch, the fusing section is very hot and you may get burnt. % Be sure to start o perations when the temperatu[...]

  • Seite 37

    bizhub PRO C6500/bizhub PRO C6500e 2 bizhub PRO C6500 / bizhub PRO C6500e 2-23 4 While lifting the lever marked in the pi cture, turn the handle in the arrow marked direction and pull out the ADU. 5 Open the front door and the toner supply section. lever[...]

  • Seite 38

    2 bizhub PRO C6500/bizhub PRO C6500e 2-24 bizhub PRO C6500 / bizhub PRO C6500e 6 Remove the screw, and remove the connector cover. 7 Disconnect the connect or. screw connector cove r connector[...]

  • Seite 39

    bizhub PRO C6500/bizhub PRO C6500e 2 bizhub PRO C6500 / bizhub PRO C6500e 2-25 8 Remove the screw, and remove the knob. 9 Remove the two screws and re move the front fusing cover. screw screws knob front fusing cov er[...]

  • Seite 40

    2 bizhub PRO C6500/bizhub PRO C6500e 2-26 bizhub PRO C6500 / bizhub PRO C6500e 10 Disconnect the two connectors. 11 Open the rev erse/exit section. 12 Remove the screw and re move the fusing unit. – When installing/removing the f using unit, be sure to hold both ends of the unit and slide i t toward you in the direction of the arrow before liftin[...]

  • Seite 41

    3 PF-601/HT504[...]

  • Seite 42

    [...]

  • Seite 43

    PF-601/HT504 3 bizhub PRO C6500 / bizhub PRO C6500e 3-3 3 PF-601/HT504 3.1 Maintenance procedur e of the tray section Removing the pick-up ru bber/paper feed roller Periodically replac ed parts/cycle: - Pick-up rubber: Every 60 0,000 prints (actual replacement cycl e: every 300,000 feed) - Paper feed roller: Every 60 0,000 print s (actual replaceme[...]

  • Seite 44

    3 PF-601/HT504 3-4 bizhub PRO C6500 / bizhub PRO C6500e 4 Open the front d oor. 5 Open the vertical c onveyance unit guide plate (tra y 4 only). front door vertical hole tray lock lever tray conveyance unit guide plate[...]

  • Seite 45

    PF-601/HT504 3 bizhub PRO C6500 / bizhub PRO C6500e 3-5 6 Insert a screwdriver or a similar tool into the hole, lift up the tray lock lever slightly, and pull out the tray. – Do not pull out tray all the way. Hold tray so that the stopper on the left side of the tray pushed in , and make the pi ck-up holder assy placed horizontally (paper feed po[...]

  • Seite 46

    3 PF-601/HT504 3-6 bizhub PRO C6500 / bizhub PRO C6500e 7 Rotate the pick-up roller in the dire ction of the arrow (clockwi se as seen from the front side) and bring the coupling to the shown position. – Be sure not to rotate the pick-up roller agai nst the direction of the arrow forcibly, as the roller is de signed not to rotate in that directio[...]

  • Seite 47

    PF-601/HT504 3 bizhub PRO C6500 / bizhub PRO C6500e 3-7 10 Move the rear be aring to the re ar side. – When installing the bearing, hold down the metal plate of the pick- up roller assy slightly, and insert the flat part of the rear bearing while keeping it horizontally into the notch of the metal plat e. Then, insert the fro nt bearin g in the s[...]

  • Seite 48

    3 PF-601/HT504 3-8 bizhub PRO C6500 / bizhub PRO C6500e 12 Remove the pick-up roller shaft from th e arm of the paper feed guide plate and remove the pick-up r oller assy. 13 Remove the C-clip, pull out the shaf t, and remove the pick-up roller. arm pick-up roller assy pick-up roller shaft C-clip pick-up roller shaft[...]

  • Seite 49

    PF-601/HT504 3 bizhub PRO C6500 / bizhub PRO C6500e 3-9 14 Remove the pick-up rubber from the pick-up roller. 15 Replace the pick-up rubber. 16 Remove the C-clip and remove the bearin g 1. 17 Slide the bearing 2 and remove the pa per feed roller together with the shaft. 18 Remove the actuator f rom the shaft. C-clip bearing 1 bearing 2 paper feed r[...]

  • Seite 50

    3 PF-601/HT504 3-10 bizhub PRO C6500 / bizhub PRO C6500e 19 Remove the C-clip and pull out th e paper feed roller from the collar. 20 Replace the paper feed roller. – The appeara nce of the collars is the same for the paper feed roller and the separation roller. Howeve r, the collar of the paper feed roller has a one-way mechanism in side while t[...]

  • Seite 51

    PF-601/HT504 3 bizhub PRO C6500 / bizhub PRO C6500e 3-11 Removing separat ion roller Periodically replac ed parts/cycle - Separation roller: Every 600,000 prints (actu al replacement cycle: every 300,000 feed) 2 Note The appearance of the collars is the same for the pa per feed roller and the separation roller. However, the co llar of the paper fee[...]

  • Seite 52

    3 PF-601/HT504 3-12 bizhub PRO C6500 / bizhub PRO C6500e 4 Open the front d oor. 5 Open the vertical c onveyance unit guide plate (tra y 4 only). 6 Insert a screwdriver or a similar tool into the hole, lift up the tray lock lever slightly, and pull out the tray. front door vertical hole tray lock lever tray conveyance unit guide plate[...]

  • Seite 53

    PF-601/HT504 3 bizhub PRO C6500 / bizhub PRO C6500e 3-13 7 Remove two screws. 8 Disengage the coupling pin from the joint wh ile pressing down the metal plate of the separation rolle r assy, and remove the s eparation roller assy. – When installing the separation roller assy, press down the metal plate of the separation roller a ssy and engage th[...]

  • Seite 54

    3 PF-601/HT504 3-14 bizhub PRO C6500 / bizhub PRO C6500e 9 Remove the C-clip of the separa tion ro ller assy and remove the separation roller together with the shaf t. shaft separation roll er C-clip[...]

  • Seite 55

    PF-601/HT504 3 bizhub PRO C6500 / bizhub PRO C6500e 3-15 10 Pull out the gear, the collar and the separation roller from the shaft to the arrow-marked direct ion, and remove them. 11 Replace the pick- up roller. 2 Note The appearance of the collars is the same for the pa per feed roller and the separation roller. However, the collar of th e paper f[...]

  • Seite 56

    3 PF-601/HT504 3-16 bizhub PRO C6500 / bizhub PRO C6500e Reinstalling the s eparation roller % Reinstall the above parts following the removal steps in reverse.[...]

  • Seite 57

    4 DF-609[...]

  • Seite 58

    [...]

  • Seite 59

    DF-609 4 bizhub PRO C6500 / bizhub PRO C6500e 4-3 4D F - 6 0 9 4.1 Maintenance procedure of the paper feeding section Removing the paper feed un it 1 Turn OFF the sub power switch. 2 Open the left front door, and then tr un OFF the main power switch. 3 Unplug the power cord. left front door main power switch sub power switch[...]

  • Seite 60

    4 DF-609 4-4 bizhub PRO C6500 / bizhub PRO C6500e 4 Open the paper feed cover. 5 Release the two loc ks of the paper fe ed guide. 6 Turn the paper feed guid e in the direction of the two arrows while pushing in the paper feed uni t to the paper feed cover side, and remove the paper feed guide upward. – When installing the paper feed guide, fit th[...]

  • Seite 61

    DF-609 4 bizhub PRO C6500 / bizhub PRO C6500e 4-5 7 Remove the screw and remove the sh aft securing plate. 8 Remove the tw o C-clips. screw shaft securing pl ate C-clip bearing paper feed unit C-clip bearing[...]

  • Seite 62

    4 DF-609 4-6 bizhub PRO C6500 / bizhub PRO C6500e 9 Slide the two bearings inward, and remove the paper feed unit. – When removing the paper feed unit , be sure not to damage the arm with the shaft. – When installing the paper feed unit , make sure the arm is mounted on the shaft. – When installing the paper feed unit, insert the tab under th[...]

  • Seite 63

    DF-609 4 bizhub PRO C6500 / bizhub PRO C6500e 4-7 Removing the pick-up roller/paper feed roller Periodically replac ed parts/cycle - Paper feed roller: Eve ry 1,800,000 print s (actual replacement cycle: every 625,000 feed) - Pick-up roller: Every 1,800,000 prints (actual replacement c ycle: every 625,000 feed) 1 Turn OFF the sub power switch. 2 Op[...]

  • Seite 64

    4 DF-609 4-8 bizhub PRO C6500 / bizhub PRO C6500e 5 Remove the b earing. 6 Remove the C-clip. 7 Slide the gear in the direction of the arrow and remove the pin. Then remove the gear and the belt in the direction of the arr ow. bearing C-cli p gear belt pin[...]

  • Seite 65

    DF-609 4 bizhub PRO C6500 / bizhub PRO C6500e 4-9 8 Remove the C-clip, then rem ove the gear and th e pin. – Be carefu l not to lose the pin as it may drop off the shaft when removing the gear. 9 Remove the arm and the pin. – Be carefu l not to lose the pin as it may drop off the shaft when removing the arm. C-clip gear pin arm pin[...]

  • Seite 66

    4 DF-609 4-10 bizhub PRO C6500 / bizhub PRO C6500e 10 Remove the C-clip, and remove the pick-up roller assy from the paper feed roller assy. 11 Remove the C-clip and pull out the paper feed roller from the shaft to replace it with new one. – When installing the paper feed roller, make sure that the arrow mark on the paper feed roller is facing th[...]

  • Seite 67

    DF-609 4 bizhub PRO C6500 / bizhub PRO C6500e 4-11 13 Remove the pin and remo ve the pick-up roller. 14 Remove the C-clip. – Be carefu l not to lose the pin as it may drop off the shaft when removing the C-clip. 15 Remove the pin and remo ve the pick-up roller. Reinstalling the pick-up roller/paper feed ro ller % Reinstall the above parts followi[...]

  • Seite 68

    4 DF-609 4-12 bizhub PRO C6500 / bizhub PRO C6500e Removing the separati on roller Periodically replac ed parts/cycle - Separation roller: Every 1,80 0,000 prints (actual replacement cyc le: every 625,000 feed) 1 Turn OFF the sub power switch. 2 Open the left front door, and then turn OFF the main power switch. 3 Unplug the power cord. left front d[...]

  • Seite 69

    DF-609 4 bizhub PRO C6500 / bizhub PRO C6500e 4-13 4 Open the paper feed cover. 5 Push the two tabs inward to re lease th e lock and remove th e separation unit cover. tabs paper feed cover tabs[...]

  • Seite 70

    4 DF-609 4-14 bizhub PRO C6500 / bizhub PRO C6500e 6 Pinch both ends of the roller sh aft and raise the separation roller straight up . 7 Remove the separation unit and replace it with a new one. Reinstalling the pick-u p roller/paper feed roller % Reinstall the above parts following the removal steps in reverse. separation ro ller separation unit[...]

  • Seite 71

    DF-609 4 bizhub PRO C6500 / bizhub PRO C6500e 4-15 Cleaning the timing sensor (PS302) Periodically cleaned parts/cycle - Timing sensor (PS302): Every 200,000 prints 1 Turn OFF the sub power switch. 2 Open the left front door, and then turn O FF the main power switch. 3 Unplug the power cord. left front door main power switch sub power switch[...]

  • Seite 72

    4 DF-609 4-16 bizhub PRO C6500 / bizhub PRO C6500e 4 Secure the hinge adjustment bracket at 90 degrees. 5 Open the DF vertically. 6 Remove the two screws and open th e metal frame in the direction of the arrow. – The two screws are different from ea ch other, so try not to mix them up. 7 Clean the timing sensor (PS302) through the hole with a blo[...]

  • Seite 73

    DF-609 4 bizhub PRO C6500 / bizhub PRO C6500e 4-17 Removing the registration roller cover 1 Turn OFF the sub power switch. 2 Open the left front door, and then turn O FF the main power switch. 3 Unplug the power cord. left front door main power switch sub power switch[...]

  • Seite 74

    4 DF-609 4-18 bizhub PRO C6500 / bizhub PRO C6500e 4 Open the paper feed cover. 5 Raise the paper feed tray straight up. 6 Remove the four screws and remo ve the registration roller cover. Reinstalling the regist ration roller cover % Reinstall the above parts following the removal steps in reverse. paper feed tray screws registration roller cover [...]

  • Seite 75

    DF-609 4 bizhub PRO C6500 / bizhub PRO C6500e 4-19 Cleaning the registration roller Periodically cleaned parts/cycle: - Registration roller: Every 200,000 prints 1 Turn OFF the sub power switch. 2 Open the left front door, and then turn O FF the main power switch. 3 Unplug the power cord. left front door main power switch sub power switch[...]

  • Seite 76

    4 DF-609 4-20 bizhub PRO C6500 / bizhub PRO C6500e 4 Remove the registration roller cover. For detail, refer to "Removing the registration roller co ver" on page 4-17. 5 Soak cotton waste with alcohol and wipe t he three registration rollers with it. 6 Reinstall the registration roller cover. For details, refer to "Reinstalling the r[...]

  • Seite 77

    DF-609 4 bizhub PRO C6500 / bizhub PRO C6500e 4-21 Cleaning the registration sensor (PS301) Periodically cleaned parts/cycle Registration sensor: Every 200,000 prints 1 Turn OFF the sub power switch. 2 Open the left front door, and then turn O FF the main power switch. 3 Unplug the power cord. left front door main power switch sub power switch[...]

  • Seite 78

    4 DF-609 4-22 bizhub PRO C6500 / bizhub PRO C6500e 4 Remove the registrati on roller cover. For details, refer to "Removing the registration roller co ver" on page 4-17. 5 Clean the registration sensor (PS301 ) with a blower brush or a similar tool. 6 Reinstall the registration roller cover. For details, refer to "Reinstalling the re[...]

  • Seite 79

    5 Appendix[...]

  • Seite 80

    [...]

  • Seite 81

    Appendix 5 bizhub PRO C6500 / bizhub PRO C6500e 5-3 5 Appendix 5.1 Replacement parts list Main body Part name Part number Toner collection box A03UR7020 Dust-proof fi lter 1 (right side) exchanging a ssy A03UR7010 Dust-proof filter 2 (rear side) 65AAR7180 Feed / reverse (separation ) rubber (tray 1) 25SA40960E Feed / reverse (separation ) rubber (t[...]

  • Seite 82

    5 Appendix 5-4 bizhub PRO C6500 / bizhub PRO C6500e Paper feeding unit PF-601 Document feeder DF-609 Part name Part number Pick-up rubber 55VA4111 Paper feed roller 55VA-483 Separation roller 55VA-483 Part name Part number Pick-up roller 13YH4039 Paper feed roller 13YH4064 Separation roller 20AJ4015[...]