Husqvarna 327RJX-series Bedienungsanleitung

E E E E n n n n g g g g l l l l i i i i s s s s h h h h 327RJ X-series Oper ator ′ s manual Please r ead the operator’ s manual carefully and mak e sure you understand the instructions before using the machine.[...]

KEY T O SYMBOLS 2 – English Symbols W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of the operator’ s manual. Please read the operator’ s manual carefully and make[...]

CONTENTS English – 3 Contents Note the f ollowing bef ore starting: Please read the oper ator’ s manual carefully . KEY T O SYMBOLS Symbols ................................................................ 2 CONTENTS Contents ............................................................... 3 Note the follo wing before starting: ..................[...]

4 – English INTR ODUCTION Dear Customer , Cong ratulations on your choice to b uy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River , for production of muskets . The location was logical, since w ater power was har[...]

English – 5 WHA T IS WHA T? What is what on the trimmer? 1 3 2 4 17 18 24 25 19 4 26 21 27 16 7 28 8 9 30 10 29 11 12 15 14 13 22 23 20 1 5 6 1 T rimmer head 2 Grease filler cap, be vel gear 3 Bev el gear 4 Cutting attachment guard 5 Shaft 6 Loop handle 7 Throttle control 8 Stop switch 9 Throttle lock out 10 Cylinder cov er 11 Star ter handle 12[...]

GENERAL SAFETY PRECA UTIONS 6 – English Impor tant P ersonal protective equipment HELMET A protectiv e helmet where there is a risk of falling objects HEARING PRO TECTION Wear hearing protection that provides adequate noise reduction. EYE PRO TECTION Alwa ys wear approved e ye protection. If you use a visor then you must also w ear approved prote[...]

GENERAL SAFETY PRECA UTIONS English – 7 BOO TS Wear boots with steel toe-caps and non-slip sole . CLO THING Wear clothes made of a strong f abric and avoid loose clothing that can catch on twigs and branches. Alwa ys wear heavy , long pants. Do not wear je weller y , shorts sandals or go barefoot. Secure hair so it is abo ve shoulder lev el. FIRS[...]

GENERAL SAFETY PRECA UTIONS 8 – English Stop switc h Use the stop switch to s witch off the engine. Star t the engine and make sure the engine stops when you mov e the stop switch to the stop setting. Cutting attachment guar d This guard is intended to prev ent loose objects from being thrown tow ards the operator . The guard also protects the op[...]

GENERAL SAFETY PRECA UTIONS English – 9 fi tted with a catalytic conv er ter is also designed to reduce harmful exhaust gases. In countries that have a w ar m and dry climate there is a significant risk of fire. W e therefore fit certain mufflers with a spark arrestor mesh. Check whether the muffler on your machine is fitted with this kind[...]

GENERAL SAFETY PRECA UTIONS 10 – English Cutting equipment This section describes how to choose and maintain your cutting equipment in order to: • Reduce the risk of blade thrust. • Obtain maximum cutting perf or mance. • Extend the life of cutting equipment. Cutting equipment Grass blades and g rass cutters are intended for cutting coarse [...]

GENERAL SAFETY PRECA UTIONS English – 11 T rimmer head • Only use the recommended trimmer heads and trimmer cords. These have been tested b y the manuf acturer to suit a par ticular engine size. This is especially impor tant when a fully automatic trimmer head is used. Only use the recommended cutting attachment. See the chapter on T echnical d[...]

ASSEMBL Y 12 – English Fitting the J-handle • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. • Slide the spacer into the slot in the loop handle. • Fit the nut, knob and screw . Do not ov er tighten. • Attach the J-handle to the loop handle using the three screws, as sho wn.[...]

ASSEMBL Y English – 13 CA UTION! Use the recommended blade guard. See the T echnical data section. • Fit the drive disc (B) on the output shaft. • T urn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. • Inser t the locking pin (C) in the hole to loc k the shaft. • Place the [...]

FUEL HANDLING 14 – English Fuel safety Nev er star t the machine: 1 If you ha ve spilt fuel on it. Wipe off the spillage and allow remaining fuel to e vaporate. 2 If you ha ve spilt fuel on yourself or y our clothes, change your clothes. W ash any par t of your body that has come in contact with fuel. Use soap and water . 3 If the machine is leak[...]

FUEL HANDLING English – 15 Mixing • Alwa ys mix the petrol and oil in a clean container intended for fuel. • Alwa ys star t by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol. • Mix (shake) the fuel mixture thoroughly bef ore filling the [...]

ST AR TING AND ST OPPING 16 – English Check bef ore star ting • Check the b lade to ensure that no cracks hav e formed at the bottom of the teeth or by the centre hole. The most common reason why cr acks are formed is that sharp cor ners have been f ormed at the bottom of the teeth while sharpening or that the blade has been used with dull teet[...]

ST AR TING AND ST OPPING English – 17 Choke: Set the choke control in the chok e position. Hold the body of the machine on the ground using your left hand (CA UTION! Not with your foot!). Grip the starter handle, slowly pull out the cord with y our right hand until you f eel some resistance (the star ter pawls grip), now quickly and pow erfully p[...]

W ORKING TECHNIQ UES 18 – English General working instructions Basic safety rules 1 Look around you: • T o ensure that people, animals or other things cannot affect y our control of the machine. • T o ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects that are thrown out by the cutting att[...]

W ORKING TECHNIQ UES English – 19 Basic working tec hniques Alwa ys slow the engine to idle speed after each working operation. Long periods at full throttle without any load on the engine can lead to serious engine damage. Grass clearing using a grass b lade • Grass blades and g rass cutters must not be used on woody stems. • A grass b lade [...]

W ORKING TECHNIQ UES 20 – English Cutting • The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower . Keep the cord parallel to the ground when cutting. A void pressing the trimmer head against the ground as this can ruin the lawn and damage the tool. • Do not allow the trimmer head to constantly come into[...]

MAINTENANCE English – 21 Carburettor Y our Husqvarna product has been designed and manuf actured to specifications that reduce har mful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. T o ensure that it continues to run at peak performance and to minimise harmful exhaust emissions after the running-in period, a[...]

MAINTENANCE 22 – English Low speed jet L T r y to find the highest idle speed by turning the low speed jet L clockwise then anti-cloc kwise. When the highest speed has been found, turn the low speed jet L 1/4 turn anti-clockwise. CA UTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned an[...]

MAINTENANCE English – 23 Muffler CA UTION! Some mufflers are fitted with a catalytic conv er ter. See chapter on T echnical data to see whether your machine is fitted with a catalytic con ver ter . The muffler is designed to reduce the noise le vel and to direct the exhaust gases a way from the oper ator. The exhaust gases are hot and can co[...]

MAINTENANCE 24 – English If the machine is low on pow er, difficult to start or runs poorly at idle speed: alw ays check the spark plug first before taking an y fur ther action. If the spar k plug is dir ty , clean it and check that the electrode gap is 0.5 mm. The spark plug should be replaced after about a month in operation or earlier if nec[...]

English – 25 MAINTENANCE Maintenance schedule The follo wing is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and ser vice work described in this Operator’s Man ual. More e xtensive work must be carried out by an authorise[...]

26 – English TECHNICAL D A T A T ec hnical data Note 1: Noise emissions in the environment measured as sound power (L W A ) in conformity with EC directive 2000/14/ EC. Note 2: Equivalent sound pressure le vel is calculated as the time-weighted energy total for sound pressure le vels under various working conditions with the follo wing time distr[...]

English – 27 TECHNICAL D A T A EC-declaration of conf ormity (Applies to Eur ope only) W e, Husqvarna AB, SE-561 82 Huskv ar na, Sweden, tel: +46-36-146500, declare that the clearing saws Husqvarna 327RJx with serial numbers dating from 2008 onwards (the year is clearly stated on the rating plate , followed b y the serial number), comply with the[...]

[...]

"Clic" 1 2 3 5 6 7 10 11 8,5 m 28' 4 8 4,2 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm S35[...]

1 2 4 3 2,4-2,7 mm .095-.106" 4,25 m 14' 4,25 m 14' B 6" 15 cm A 6" 15 cm S35 5[...]

T35, T35x "Clic" 1 2 3 5 6 7 9 8,5 m 28' 4 8 4,3 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm[...]

"Clic" 1 2 3 5 6 7 9 6,0 m 18' 4 8 3,05 m 9' 2,0-2,4 mm .079-.095" 10 cm 4" 6" 15 cm T25[...]

[...]

[...]

[...]

1150990-26 ´®z+R•"¶6N¨ ´®z+R•"¶6N¨ 2008-05-20[...]