Deutsch dropdown-ico

Husqvarna 1130SB-LSB Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44

Zur Seite of

Ähnliche Gebrauchsanleitungen

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Husqvarna 1130SB-LSB an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Husqvarna 1130SB-LSB, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Husqvarna 1130SB-LSB die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Husqvarna 1130SB-LSB. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Husqvarna 1130SB-LSB sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Husqvarna 1130SB-LSB
- Den Namen des Produzenten und das Produktionsjahr des Geräts Husqvarna 1130SB-LSB
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Husqvarna 1130SB-LSB
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Husqvarna 1130SB-LSB zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Husqvarna 1130SB-LSB und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Husqvarna finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Husqvarna 1130SB-LSB zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Husqvarna 1130SB-LSB, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Husqvarna 1130SB-LSB widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    1130SB -LSb 1130SB -LSb Owner's Manual / 96193003800 / 2009-06[...]

  • Seite 2

    2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. F ailure to observe the following safety instructions could result in serious injury . WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be e[...]

  • Seite 3

    3 CONGRA TUL A TIONS on your purchase of a new snow thrower . It has been designed, engineered and man u fac - tured to give best possible dependability and per for mance. Should you experience any problem you cannot easily remedy , please contact your nearest authorized service center . W e have competent, well-trained tech ni cians and the proper[...]

  • Seite 4

    4 P ARTS P ACKED SEP ARA TEL Y IN CARTON (1) POWER CORD (198563) (1) DISCHARGE CHUTE (6) SHEAR BOL TS 1/4-20 x 1-3/4 (198636) (6) SP ACERS (198638) (1) WASHER 3/8 (19131316) (1) L OCKNUT 5/16-18 (751153) (1) CARRIAGE BOL T 5/16-18 x 5/8 (72250505) (1) L OCKNUT 1/4-20 (191730) (1) NYL ON WASHER (179246) (1) SHOULDER BOL T 1/4-20 (179829) (1) SPRING [...]

  • Seite 5

    5 AS SEMBL Y / PRE-OPERA TION NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad just ments to the skid plates. UNFOLD UPPER HANDLE 1. Raise upper handle to the operating position and tight en handle knobs securely . Additional carriage bolts, washers and handle knobs are in bag of parts. Use to [...]

  • Seite 6

    6 AS SEMBL Y / PRE-OPERA TION INST ALL DISCHARGE CHUTE / CHUTE ROT A TER HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower . 2. Position chute rotater head over chute bracket. If[...]

  • Seite 7

    7 AS SEMBL Y / PRE-OPERA TION CHECK TIRE PRESSURE The tires on your snow thrower were overinflated at the fac- tory for shipping purposes. Correct and equal tire pres sure is important for best snow throwing performance. • Reduce tire pressure to 14-17 PSI (19-24.5 N-m). INST ALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9) 1. Install remot[...]

  • Seite 8

    8 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literat[...]

  • Seite 9

    9 RECOIL (AUXILIARY) ST ARTER HANDLE THROTTLE / ENGINE CONTROL MUF FLER GAS O LINE FILLER CAP SAFETY IGNITION KEY CHOKE CON- TROL ELECTRIC ST ART BUTTON PRIM ER FUEL SHUT -OFF VAL VE OPERA TION Drive speed control lever - used to select forward or reverse motion and speed of snow thrower . T raction drive control lever - used to engage power - pro [...]

  • Seite 10

    10 The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any ad just- ments or repairs. We recommend standard safe ty glasses or a wide vision safety mask worn over spectacles. HOW TO USE Y[...]

  • Seite 11

    11 TO MOVE FORWARD AND BACK WARD (See Fig. 17) SELF-PROPELLING, forward and reverse movement of the snow thrower , is controlled by the traction drive control lever located on the left side handle. OPERA TION TO THROW SNOW (See Fig. 15) The auger rotation is controlled by the auger control lever located on the right side handle. • Squeeze auger c[...]

  • Seite 12

    12 OPERA TION BEFORE ST ARTING THE ENGINE CHECK ENGINE OIL LEVEL (See Fig. 21) The engine on your snow thrower has been shipped, from the factory , already filled with oil. 1. Check engine oil with snow thrower on level ground. 2. Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and [...]

  • Seite 13

    13 OPERA TION TO ST ART ENGINE • Be sure fuel shut-off valve is in the “OPEN” position. Y our snow thrower engine is equipped with both a 120 V olt A.C. electric starter and a recoil starter . The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 V olt A .C. household current. • Be sure you[...]

  • Seite 14

    14 MAINTENANCE LUBRICA TION CHART GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual. Some ad just ments will need to be made periodically to proper[...]

  • Seite 15

    15 MAINTENANCE BEL TS Check belts for deterioration and wear after every 50 hours of operation and replace if necessary . The belts are not ad just able. Replace belts if they begin to slip from wear . (See “TO REMOVE BEL T COVER” in the Service and Adjustments section of this manual). The belts on your snow thrower are of special con struc tio[...]

  • Seite 16

    16 SERVICE AND ADJUSTMENTS WARNING: T o avoid serious injury , before performing any service or ad- just ments: 1. Be sure throttle is in STOP position. 2. Remove safety ignition key . 3. Make sure the augers and all mov ing parts have completely stopped. 4. Disconnect spark plug wire from spark plug and place wire where it can not come in contact [...]

  • Seite 17

    17 SERVICE AND ADJUSTMENTS TO REPL ACE BEL TS (See Fig. 24) The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear , they should be replaced. It is recommended that the belt(s) be replaced by a qualified service center . NOTE: It is recommended that both the auger and traction drive belt be replac[...]

  • Seite 18

    18 STORAGE Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open flame, spark or pilot light as on a fur nace, water heater , clothes dryer or gas ap pli ance. A[...]

  • Seite 19

    19 Does not start 1. F uel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Refill fuel tank with fresh, clean gasoline. 4. Throttle in STOP position. 4. Move throttle to F AST position. 5. Choke in OFF position.[...]

  • Seite 20

    20 REP AIR P ARTS A UGER HOUSING / IMPELLER AS SEMBL Y SNOW THROWER - MODEL NO . 1130SB-LSB 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow[...]

  • Seite 21

    21 REP AIR P ARTS A UGER HOUSING / IMPELLER AS SEMBL Y SNOW THROWER - MODEL NO . 1130SB-LSB 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow[...]

  • Seite 22

    22 REP AIR P ARTS A UGER HOUSING / IMPELLER AS SEMBL Y SNOW THROWER - MODEL NO . 1130SB-LSB 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replaceme[...]

  • Seite 23

    23 REP AIR P ARTS A UGER HOUSING / IMPELLER AS SEMBL Y SNOW THROWER - MODEL NO . 1130SB-LSB 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 1 2 3 3 2 01.11.002-A 1 532 40 78-34 SKID PL A TE 2 872 27 05-06 CARRIAGE BOL T 5/16 − 18 X .750 3 532 75 11-53 NUT 5/16 − 18 NOTE: All c[...]

  • Seite 24

    24 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS A UGER HOUSING / IMPELLER AS SEMBL Y SNOW THROWER - MODEL N[...]

  • Seite 25

    25 REP AIR P ARTS CONTROL P ANEL / DISCHARGE CHUTE SNOW THROWER - MODEL NO . 1130SB-LSB 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thr[...]

  • Seite 26

    26 REP AIR P ARTS CONTROL P ANEL / DISCHARGE CHUTE SNOW THROWER - MODEL NO . 1130SB-LSB 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thr[...]

  • Seite 27

    27 REP AIR P ARTS HANDLES SNOW THROWER - MODEL NO . 1130SB-LSB 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warran[...]

  • Seite 28

    28 REP AIR P ARTS HANDLES SNOW THROWER - MODEL NO . 1130SB-LSB 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warran[...]

  • Seite 29

    29 REP AIR P ARTS HANDLES SNOW THROWER - MODEL NO . 1130SB-LSB 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warran[...]

  • Seite 30

    30 REP AIR P ARTS HANDLES SNOW THROWER - MODEL NO . 1130SB-LSB 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warran[...]

  • Seite 31

    31 REP AIR P ARTS HANDLES SNOW THROWER - MODEL NO . 1130SB-LSB 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warran[...]

  • Seite 32

    32 REP AIR P ARTS DRIVE SNOW THROWER - MODEL NO . 1130SB-LSB 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty[...]

  • Seite 33

    33 REP AIR P ARTS DRIVE SNOW THROWER - MODEL NO . 1130SB-LSB 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty[...]

  • Seite 34

    34 REP AIR P ARTS DRIVE SNOW THROWER - MODEL NO . 1130SB-LSB 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38 01.02.001-F_Sheet_1 1 2 1 3 4 5 6 5 7 8 9 10 11 12 1 2 3 2 1 28 2 2 14 13 14 14 2 2 2 28 15 3 1 1 16 3 1 1 2 20 17 18 19 4 4 8 8 23 24 27 25 27 21 28 28 22 26 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NOTE: All compo[...]

  • Seite 35

    35 KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS DRIVE SNOW THROWER - MODEL NO . 1130SB-LSB 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38 KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so cou[...]

  • Seite 36

    36 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS DRIVE SNOW THROWER - MODEL NO . 1130SB-LSB 1130SB-LSB (9619[...]

  • Seite 37

    37 REP AIR P ARTS CHAS SIS / ENGINE / PULLEYS SNOW THROWER - MODEL NO . 1130SB-LSB 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower [...]

  • Seite 38

    38 REP AIR P ARTS CHAS SIS / ENGINE / PULLEYS SNOW THROWER - MODEL NO . 1130SB-LSB 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower [...]

  • Seite 39

    39 REP AIR P ARTS WHEELS SNOW THROWER - MODEL NO . 1130SB-LSB 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warrant[...]

  • Seite 40

    40 REP AIR P ARTS BAG OF P ARTS SNOW THROWER - MODEL NO . 1130SB-LSB 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your [...]

  • Seite 41

    41 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O .E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P ARTS DECALS SNOW THROWER - MODEL NO . 1130SB-LSB 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00[...]

  • Seite 42

    42 SERVICE NOTES[...]

  • Seite 43

    43 SERVICE NOTES[...]

  • Seite 44

    532 42 35-16 11.11.08 TH Printed in the U.S.A. SECTION 1: LIMITED W ARRANTY Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from defects in material and workmanship from the date of purchase for the “Warranty Period” of the product as set forth below: Lifetime Warranty (Par[...]