Hornet Car Security 700T Bedienungsanleitung

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28

Zur Seite of

Richtige Gebrauchsanleitung

Die Vorschriften verpflichten den Verkäufer zur Übertragung der Gebrauchsanleitung Hornet Car Security 700T an den Erwerber, zusammen mit der Ware. Eine fehlende Anleitung oder falsche Informationen, die dem Verbraucher übertragen werden, bilden eine Grundlage für eine Reklamation aufgrund Unstimmigkeit des Geräts mit dem Vertrag. Rechtsmäßig lässt man das Anfügen einer Gebrauchsanleitung in anderer Form als Papierform zu, was letztens sehr oft genutzt wird, indem man eine grafische oder elektronische Anleitung von Hornet Car Security 700T, sowie Anleitungsvideos für Nutzer beifügt. Die Bedingung ist, dass ihre Form leserlich und verständlich ist.

Was ist eine Gebrauchsanleitung?

Das Wort kommt vom lateinischen „instructio”, d.h. ordnen. Demnach kann man in der Anleitung Hornet Car Security 700T die Beschreibung der Etappen der Vorgehensweisen finden. Das Ziel der Anleitung ist die Belehrung, Vereinfachung des Starts, der Nutzung des Geräts oder auch der Ausführung bestimmter Tätigkeiten. Die Anleitung ist eine Sammlung von Informationen über ein Gegenstand/eine Dienstleistung, ein Hinweis.

Leider widmen nicht viele Nutzer ihre Zeit der Gebrauchsanleitung Hornet Car Security 700T. Eine gute Gebrauchsanleitung erlaubt nicht nur eine Reihe zusätzlicher Funktionen des gekauften Geräts kennenzulernen, sondern hilft dabei viele Fehler zu vermeiden.

Was sollte also eine ideale Gebrauchsanleitung beinhalten?

Die Gebrauchsanleitung Hornet Car Security 700T sollte vor allem folgendes enthalten:
- Informationen über technische Daten des Geräts Hornet Car Security 700T
- Den Namen des Produzenten und das Produktionsjahr des Geräts Hornet Car Security 700T
- Grundsätze der Bedienung, Regulierung und Wartung des Geräts Hornet Car Security 700T
- Sicherheitszeichen und Zertifikate, die die Übereinstimmung mit entsprechenden Normen bestätigen

Warum lesen wir keine Gebrauchsanleitungen?

Der Grund dafür ist die fehlende Zeit und die Sicherheit, was die bestimmten Funktionen der gekauften Geräte angeht. Leider ist das Anschließen und Starten von Hornet Car Security 700T zu wenig. Eine Anleitung beinhaltet eine Reihe von Hinweisen bezüglich bestimmter Funktionen, Sicherheitsgrundsätze, Wartungsarten (sogar das, welche Mittel man benutzen sollte), eventueller Fehler von Hornet Car Security 700T und Lösungsarten für Probleme, die während der Nutzung auftreten könnten. Immerhin kann man in der Gebrauchsanleitung die Kontaktnummer zum Service Hornet Car Security finden, wenn die vorgeschlagenen Lösungen nicht wirksam sind. Aktuell erfreuen sich Anleitungen in Form von interessanten Animationen oder Videoanleitungen an Popularität, die den Nutzer besser ansprechen als eine Broschüre. Diese Art von Anleitung gibt garantiert, dass der Nutzer sich das ganze Video anschaut, ohne die spezifizierten und komplizierten technischen Beschreibungen von Hornet Car Security 700T zu überspringen, wie es bei der Papierform passiert.

Warum sollte man Gebrauchsanleitungen lesen?

In der Gebrauchsanleitung finden wir vor allem die Antwort über den Bau sowie die Möglichkeiten des Geräts Hornet Car Security 700T, über die Nutzung bestimmter Accessoires und eine Reihe von Informationen, die erlauben, jegliche Funktionen und Bequemlichkeiten zu nutzen.

Nach dem gelungenen Kauf des Geräts, sollte man einige Zeit für das Kennenlernen jedes Teils der Anleitung von Hornet Car Security 700T widmen. Aktuell sind sie genau vorbereitet oder übersetzt, damit sie nicht nur verständlich für die Nutzer sind, aber auch ihre grundliegende Hilfs-Informations-Funktion erfüllen.

Inhaltsverzeichnis der Gebrauchsanleitungen

  • Seite 1

    ® © 2001 Directed Electr onics , Inc . Vista, CA N700T 8-01 Rev . E 1.1 Model 700T Installation Guide ® : http://www. guardianalarms . net[...]

  • Seite 2

    2 © 2001 Directed Electr onics , Inc . Vista, CA table o f contents What Is Included . . . . . . . . . . . . . . . . . . . . . . 3 Installation P oints to Remember . . . . . . . . . . . . 3 Befor e Beginning the In stallation . . . . . . . . . 3 After the In stallation. . . . . . . . . . . . . . . . . . 3 T ools Required . . . . . . . . . . . . . [...]

  • Seite 3

    © 2001 Directed Electr onics , Inc . Vista, CA 3 what is included ■ One con trol mod ule with on-board shock sen sor ■ One plug-in status LED ■ One plug-in V alet/progr am switch ■ One 12-pin prim ary harness (H1) ■ One 5-pin auxili ary harness (H2) ■ One Reven ger Soft-Chirp sir en installation points to r emember ■ Check with th e [...]

  • Seite 4

    4 © 2001 Directed Electr onics , Inc . Vista, CA tools r equir ed This is a gen eral list of tools r equired to complete the in stallation of this security system in m ost vehicles. Som e vehicles m ay require ad ditional tools . deciding on component locations Some thin gs to remember wh en mountin g the siren: ■ Keep it away fr om heat sources[...]

  • Seite 5

    © 2001 Directed Electr onics , Inc . Vista, CA 5 ■ Never put th e control m odule in th e engine compartm ent! ■ The first step in h ot-wiring a vehicle is r emovin g the driver's si de und erd ash panel to access the starter an d igniti on wires . If the contr ol mod ule is placed just behind the d river's side d ash it can easily b[...]

  • Seite 6

    6 © 2001 Directed Electr onics , Inc . Vista, CA IMPORT ANT! When the vehicle is delivered, please show the user where the switch is located and how to disarm the system with it. Things to r emember when positi oning the Status LED: ■ It sh ould be visible from both sid es and the r ear of the vehi cle, if possible . ■ It n eeds at least 1 / 2[...]

  • Seite 7

    © 2001 Directed Electr onics , Inc . Vista, CA 7 wiring! Exposed yellow butt conn ectors do not look lik e factory parts, an d will not fool an yone! For this reason, routin g the starter kill wires away fr om the steering column is r ecommend ed. finding the wir es y ou need Now that you have d ecided wh ere each componen t will be located, you?[...]

  • Seite 8

    8 © 2001 Directed Electr onics , Inc . Vista, CA How to fin d (+)12V ignition with your m ultimeter: 1. Set to DCV or DC voltage (12V or 20V is fin e). 2. Attach th e (-) probe of th e meter to chassis groun d. 3. Probe th e wire you suspect of bein g the igniti on wire . The steering column harn ess or ignition switch harn ess is an ex cellent pl[...]

  • Seite 9

    © 2001 Directed Electr onics , Inc . Vista, CA 9 The best places to fin d the door pin switch wire are: ■ At th e pinswitch: When testin g at the pinswitch, ch eck the wire to en sure that it “sees” all the d oors. Often, the passen ger switch will cover all the d oors even if the driver’s switch will n ot. ■ At th e domeli ght: This may[...]

  • Seite 10

    10 © 2001 Directed Electr onics , Inc . Vista, CA 4. T urn the igniti on key switch to the start positi on. Make sur e the car is not in g ear! If your meter reads (+)12V , go to th e next step. If it d oes not, probe a differ ent wire . 5. Cut the wir e you suspect of being th e starter wire . 6. Attempt to start th e car . If the starter en gage[...]

  • Seite 11

    © 2001 Directed Electr onics , Inc . Vista, CA 11 3. Insert th e twisted pair of wires in to one end o f the butt connector an d crimp securely . 4. Insert th e other end o f the vehicle’s wir e into the oth er end of th e butt connector and crimp secur ely . 1. Usin g your wire strippers and r azor knife, strip about 1 / 2 -inch of in sulation [...]

  • Seite 12

    12 © 2001 Directed Electr onics , Inc . Vista, CA primary harness (H1) wir e connection guide This guid e describes in detail th e connection o f each wire . Also includ ed are possible applicati ons o f each wire . This system was desi gned with the ultim ate in flexibility and security in min d. Man y of the wir es have more than one possible fu[...]

  • Seite 13

    © 2001 Directed Electr onics , Inc . Vista, CA 13 As shipped , this wire should be conn ected to the (+) parking li ght wire . If the li ght flash polarity jumper insi de the unit is m oved to the opposite position (see th e Internal Jumpers section of this gui de), this wire suppli es a (-) 200 mA output. This is suitable for d riving (-) parking[...]

  • Seite 14

    14 © 2001 Directed Electr onics , Inc . Vista, CA Connect this wir e to the option al domeli ght supervision r elay . IMPORT ANT! This output is only intended to drive a relay. It cannot be connected directly to the domelight circuit, as the output cannot support the current draw of one or more bulbs . Most vehi cles use negative door tri gger cir[...]

  • Seite 15

    © 2001 Directed Electr onics , Inc . Vista, CA 15 This wire is used in vehi cles that have a positive (+) switched dom e light cir cuit. Connect the vi olet wire to a wire that sh ows (+)12V when any d oor is opened, an d ground wh en the door is closed . Connect this wir e to bare metal, pr eferably with a factory bolt r ather than your own screw[...]

  • Seite 16

    16 © 2001 Directed Electr onics , Inc . Vista, CA Connect this to th e red wire o f the siren. Conn ect the black wire o f the siren to (-) chassis gr ound, pr eferably at the sam e point you connect th e control m odule’s black groun d wire . Befor e connecting this wir e, r emove the suppli ed fuse. Conn ect to the battery positive terminal or[...]

  • Seite 17

    © 2001 Directed Electr onics , Inc . Vista, CA 17 auxiliary harness (H2) wir e connection guide This wire suppli es a (-) 200 mA output that can be used to honk the vehi cle’s horn. It pr ovides a pulsed output when th e security system is in the trigg ered sequence or in pani c mode . In most vehi cles with (-) horn circuits this wire can con t[...]

  • Seite 18

    18 © 2001 Directed Electr onics , Inc . Vista, CA has no fun ction. If the custom er wants the system to autom atically lock the d oors when the system passively arms , connect this wire to th e lock circuit in the vehi cle. An opti onal relay m ay be required . IMPORT ANT! Never use this wire to drive anything but a relay or a low-current input! [...]

  • Seite 19

    © 2001 Directed Electr onics , Inc . Vista, CA 19 This system is used in man y four-door GM sed ans. T o test for this type of system, pr obe the unlock wire fr om the interi or switch (black or white). Unlock the d river’s door , by itself, using the f actory remote . If the switch wir e shows (+) 12V , th en use the followin g diagram: NOTE: I[...]

  • Seite 20

    20 © 2001 Directed Electr onics , Inc . Vista, CA NOTE: Failure to insert the diodes at the correct point will allow the system to be disarmed by one of the power door lock switches inside the vehicle . The best place to insert the diode is at the keyless entry module itself or at the relays . door lock learn r outine Befor e the unit will respon [...]

  • Seite 21

    © 2001 Directed Electr onics , Inc . Vista, CA 21 3. Press an d HOLD the V alet/progr am for three secon ds. 4. The LED will flash on ce to confirm the lock polarity was learned . plug-in harnesses The super-bri ght LED operates at 2VDC. M ake sure th e LED wires are n ot shorted to groun d as the LED will be dam aged. Th e LED fits into a 9 / 32 [...]

  • Seite 22

    22 © 2001 Directed Electr onics , Inc . Vista, CA internal pr ogr amming jumper This jumper is used to determin e the ligh t flash output. In the (+) position, th e on-board relay is en abled and the unit will output (+)12V on th e WHITE wire , H1/2. In the (-) position, th e on-board relay is disabled . The WHITE wire , H1/2, will supply a (-) 20[...]

  • Seite 23

    © 2001 Directed Electr onics , Inc . Vista, CA 23 s y stem featur es learn r outine The System Featur es Learn Routine dictates h ow the unit operates . It is possible to access and chan ge any o f the feature settin gs using the V alet/progr am switch. T o enter th e System Features Learn Routine: 1. Open a door: Th e GREEN wire , H1/5, or the VI[...]

  • Seite 24

    24 © 2001 Directed Electr onics , Inc . Vista, CA 2. Then pr ess the V alet/program switch on ce more an d HOLD it. For ex ample, if you just pr ogramm ed the secon d feature an d you would like to progr am the seventh featur e in the men u, you would press and r elease the V alet/program switch five tim es. Then pr ess it once mor e and HOLD it. [...]

  • Seite 25

    © 2001 Directed Electr onics , Inc . Vista, CA 25 3 SIREN DURA TION 30/60 SECONDS: In the d efault setting, th e full trigger ed sequence will con tinue wh en trig- ger ed for 30 seconds . This can be changed to 60 secon ds in the system features learn r outine . 4 DOOR TRIGGER INST ANT/DELA YED: In the in stant (d efault) settin g, if a door is o[...]

  • Seite 26

    26 © 2001 Directed Electr onics , Inc . Vista, CA table o f zones When usin g the diagn ostic functi ons, use th e T able of Z ones to d etermine which input has tri ggered th e system. It is also h elpful in deci ding which input to use wh en connecting opti onal sensors an d switches. r apid r esume logic This DEI system will store its curr ent [...]

  • Seite 27

    © 2001 Directed Electr onics , Inc . Vista, CA 27 ■ Door input does not immediately trigger full alarm. Instead, first I hear chirps f or three seconds. That’s how th e progressive two-stag e door input works! This is a feature o f this system. This is an instant tri gger , so even if the d oor is instantly closed , the progr ession from chirp[...]

  • Seite 28

    28 © 2001 Directed Electr onics , Inc . Vista, CA wiring quick r efer ence guide[...]